Balcrank 1300-001 Service Bulletin

Brand
Balcrank
Model
1300-001
Type
Service Bulletin

Balcrank 1300-001

The Balcrank 1300-001 is a heavy-duty barrel pump designed for transferring liquids from drums. It features a sturdy steel construction and is compatible with a wide range of fluids, including oils, solvents, and chemicals.

The pump's simple design makes it easy to assemble and operate. It comes with a variety of attachments, including a spout, base assembly, and tube section assembly, which allow it to be customized for different applications.

Balcrank 1300-001

The Balcrank 1300-001 is a heavy-duty barrel pump designed for transferring liquids from drums. It features a sturdy steel construction and is compatible with a wide range of fluids, including oils, solvents, and chemicals.

The pump's simple design makes it easy to assemble and operate. It comes with a variety of attachments, including a spout, base assembly, and tube section assembly, which allow it to be customized for different applications.

SERVICE BUTTETIN SB1054
REV. B 2/03
Thoroughly read and understand this manual before
installing, operating or servicing this equipment.
OPERATION, INSTALLATION,
MAINTENANCE AND REPAIR GUIDE
BARREL PUMP
MODEL #1300-001
ITEM PART# DESCRIPTION
A 822519 Bushing, Compression
B 822520 Seal
C 820180 Gasket, Molded
D 820178 Base Assembly
E 820827 Piston Sub Assembly
F 820829 Rings, Brass (2)
G 820184 Tube Section Assembly
H 822275 Seal
®
Balcrank
®
Corporation
Weaverville, NC 28787
800-747-5300
800-763-0840 Fax
www.balcrank.com
SERVICE BULLETIN SB1054
REV. B 2/03
822101
PARTS LIST AND INSTRUCTIONS FOR ASSEMBLING AND OPERATING
HEAVY DUTY BARREL PUMP MODEL #1300-001
1. Screw the 822521 Spout into head, engaging threads until tight. If not properly aligned,
increase pressure to further tighten spout to correct position.
2. Insert the 820184 Tube Section Assembly into the 820178 Base Assembly of the pump and
tighten securely with a small pipe wrench to eliminate any air leaks. Do not use undue force
in tightening as the base or valve may be damaged.
3. Screw the pump into the threaded bung in the drum and tighten securely by grasping the
spout in one hand and the lever in the other hand.
NOTE: The 820184 tube suction assembly will automatically adjust to the proper position.
IMPORTANT: If when the pump is tightened into the drum bung and the spout is not in the
desired position above the drum, loosen the clamp bolt on base assembly and rotate pump
housing to the desired position and retighten.
4. Pull the piston rod of piston sub-assembly up and attach the operating lever to the piston rod,
using the rivet and retainer clip, enclosed in the envelope.
5. Start the pump by several quick strokes of the lever. If the pump fails to start, check Step 2.
6. If the pump fails to start, and Item 2 has been checked, remove the pump from the drum
and check the 820184 Tube Suction Assembly to see that it is extended to reach the bottom
of the drum.
7. In as much as certain liquids have a tendency to build up a coating on the surface when
the pump is not in use.
8. If pump leaks around the 822519 compression bushing, tighten bushing by hand only.
NOTICE: This pump is made of steel. If it is used with uids that cause rusting, the rust
may interfere with the operation of the pump. Our guarantee does not cover any pump
showing rust.
Distributed by:
  • Page 1 1
  • Page 2 2

Balcrank 1300-001 Service Bulletin

Brand
Balcrank
Model
1300-001
Type
Service Bulletin

Balcrank 1300-001

The Balcrank 1300-001 is a heavy-duty barrel pump designed for transferring liquids from drums. It features a sturdy steel construction and is compatible with a wide range of fluids, including oils, solvents, and chemicals.

The pump's simple design makes it easy to assemble and operate. It comes with a variety of attachments, including a spout, base assembly, and tube section assembly, which allow it to be customized for different applications.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents