Arkon CLAMPRCB User manual

Arkon
Brand
Arkon
Model
CLAMPRCB
Category
Projector mounts
Type
User manual

Arkon CLAMPRCB is a multifunctional device that can serve as a video phone holder, tablet holder, and ring light.

With its telescoping pole that extends from 17 to 29 inches, you can adjust the height to your preference. The clamp post mount allows you to attach the device to surfaces, while the overhead arm assembly provides flexible positioning options.

The phone holder accommodates smartphones with cases weighing up to 2 pounds and measuring up to 4 inches wide. The tablet holder (sold separately) can be attached to the mount using Dual T-Tabs and Dual T-Slots.

The LED ring light provides additional illumination for video calls, photography, and other activities. The intensity of the light can be adjusted to suit your needs.

Arkon CLAMPRCB is a multifunctional device that can serve as a video phone holder, tablet holder, and ring light.

With its telescoping pole that extends from 17 to 29 inches, you can adjust the height to your preference. The clamp post mount allows you to attach the device to surfaces, while the overhead arm assembly provides flexible positioning options.

The phone holder accommodates smartphones with cases weighing up to 2 pounds and measuring up to 4 inches wide. The tablet holder (sold separately) can be attached to the mount using Dual T-Tabs and Dual T-Slots.

The LED ring light provides additional illumination for video calls, photography, and other activities. The intensity of the light can be adjusted to suit your needs.

Telescoping pole extends
upward from 17 inches to
29 inches.
Compatibility:
Fits smartphones with
cases weighing up to 2
pounds and measuring
up to 4” wide.
IMPORTANT:
Do not overtighten ring.
Overtightening may
damage threads on
holder and also make it
difficult to adjust phone
and tablet holders.
3 4
Attach mount to surface by tightening
C-clamp knob. Slide optional rubber clamp
boot onto the top of the mount’s clamp to
prevent scratching clamp surface if desired.
Attach overhead arm assembly to clamp
pedestal by unscrewing the collar at the top
of the pole until the metal ball side of the
overhead arm assembly fits into the collar.
Tighten collar clockwise to secure.
Your Remarkable Creators Bundle will arrive in seven pieces:
HD011-B
Clamp Pedestal
with Telescoping
Pole
SP25MMCAM
25mm to 1/4”-20
Camera Bolt Adapter
(optional)
2
RV001WR-B
For thicker tables or desks, adjust the clamp
bracket by using a Phillips screwdriver to
remove the screws from the top position and
move them to the bottom position.
Unscrew tightening ring from holder.
Place ring over the 17mm end of mount
then snap the holder onto the ball. Set to
desired position, then tighten ring.
Using two hands, insert phone into the
holder by pushing the device into one of the
spring-loaded support arms. Expand the other
support arm and fully insert device until it lays
flat against the blue rubber pad.
Assembled Mount
SP3RMPR0PL
Tightening Ring
Tightening
Knob
Collar
Metal
Ball side
Continued on page 2
CLAMPRCB | Remarkable Creators Video Phone and Tablet Clamp with Ring Light
rev.092418
HD011-B
RV001WR-B
Phone Holder
SPLEDRING
LED Ring Light
SP3RMPROPL
Overhead Arm
Assembly
GN031-SBH-B
Clamp Post Mount
TAB001
GN031-SBH-B
5
Shafts can be adjusted by unscrewing
the shafts’ knobs to loosen. Tighten
knobs to set.
TAB001
Tablet Holder
Clamp Bracket
C-Clamp Knob
C-Clamp
Screws
Screws
1a 1b
7
9
10
6
8
To attach optional camera/pico projector adapter, unscrew shaft knob and
remove phone holder, ring, and ball adapter. Attach the 25mm ball end of the
camera adapter to the shaft and tighten clockwise to secure.
Unscrew mount’s knob to loosen grip. Place mount around pole and
tighten knob to secure.
Attach short, medium or long support legs to the tablet holder based
on the size of your device.
Push down on lower legs of spring-loaded holder to insert tablet.
For instructions on how to assemble tablet holder, refer to included
TAB001 manual. Attach tablet holder by inserting the mount’s Dual
T-Tabs into the holder’s Dual T-Slots.
Adjust the height of the pole by loosening the adjustment collar
counterclockwise. Tighten clockwise to set height.
Consumer Hotline:
USA (800) 841-0884
INT’L (626) 25 4- 9005
Monday - Friday 9 am - 5 pm, PST
www.arkon.com
Arcadia, CA 91006 USA
Designed in USA | Made in Taiwan and USA
© Copyright 2018 Arkon Resources, Inc.
!
page 2
Tightening
Knob
OPTIONAL
rev.092418
CLAMPRCB | Remarkable Creators Video Phone and Tablet Clamp with Ring Light
Safety Precautions
Arkon Resources, Inc. is not responsible for any damages caused to your
device or yourself due to the installation or use of this mount.
  • Page 1 1
  • Page 2 2

Arkon CLAMPRCB User manual

Arkon
Brand
Arkon
Model
CLAMPRCB
Category
Projector mounts
Type
User manual

Arkon CLAMPRCB is a multifunctional device that can serve as a video phone holder, tablet holder, and ring light.

With its telescoping pole that extends from 17 to 29 inches, you can adjust the height to your preference. The clamp post mount allows you to attach the device to surfaces, while the overhead arm assembly provides flexible positioning options.

The phone holder accommodates smartphones with cases weighing up to 2 pounds and measuring up to 4 inches wide. The tablet holder (sold separately) can be attached to the mount using Dual T-Tabs and Dual T-Slots.

The LED ring light provides additional illumination for video calls, photography, and other activities. The intensity of the light can be adjusted to suit your needs.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents