Eaton i-on Series Engineering Manual

i-on Range

Page ii

IN NO EVENT WILL EATON’S SECURITY BUSINESS BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, OR INDIRECT LOSS OR

DAMAGE, INCIDENTAL DAMAGES, STATUTORY DAMAGES, EXEMPLARY DAMAGES, LOSS OF PROFITS, LOSS OF REVENUE,

LOSS OF ANTICIPATED SAVINGS, LOSS OF BUSINESS OR OPPORTUNTIY, LOSS OF GOODWILL OR INJURY TO

REPUTATION, LIQUIDATED DAMAGES OR LOSS OF USE, EVEN IF INFORMED OF THE POSSIBILITY OF SUCH DAMAGES.

EATON’S SECURITY BUSINESS’S LIABILITY FOR DAMAGES ARISING OUT OF OR RELATED TO A PRODUCT SHALL IN NO

CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT FROM WHICH THE CLAIM ARISES. TO THE EXTENT PERMITTED

BY APPLICABLE LAW, THESE LIMITATIONS AND EXCLUSIONS WILL APPLY WHETHER EATON’S SSECURITY BUSINESS’S

LIABILITY ARISES FROM BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING BUT NOT LIMITED TO

NEGLIGENCE), STRICT LIABILITY, BY OPERATION OF LAW, OR OTHERWISE.

Every effort has been made to ensure that the contents of this book are correct. The

contents of this book are subject to change without notice.

About this Guide

The i-on Engineering Guide describes:

The general architecture of systems based on i-on control units.

The options provided by the Installation Menu.

This guide applies to the i-on range of control units using version 4.04 software.

Other i-onEX Publications

To install, connect and start up an i-onEX control unit please read the Installation Guide

appropriate for the control unit.

If you need to add or administer users (and their remote controls, HUA buttons and

proximity tags) then you must enter the User Menu. This is described in detail in the i-on40

& i-onEX Administrator’s Guide and the i-on16 Administrator’s Guide.

If you wish to program an i-on40, i-on50EX/i-on50EXD, or the i-on160EX from a PC or

laptop please read i-on Range Web Server Setup Guide first.

If you wish to use Downloader then please read the Downloader Quick Guide.

A Note about screen displays

Some of the keypad screen displays in this book show the standby screen, which shows

the type of control unit on the top line. Although the book shows “i-on160EX”, the text will

be different if you are using another control unit.

Conventions

Some i-on control units do not share all the programming features available in the Installer

Menu. Where necessary the following symbols show which control unit a feature applies

to: 16 30 40 50 160. If there are no symbols then the feature applies across all i-on

control units.

Changes Since Release 4.00

This section outlines the main changes that have been introduced since Release 4.00.

(Version 4.01 was not released for i-on products, version 4.02 was not released for sale in

the UK.) Changes made since issue 6 are highlighted by a black box.

New in Issue 6 (S/W Version 4.03)

New hardware:

1. 705r now supported as a single channel HUD. The control unit ignores the top button.

2. There is a new Appendix VI showing how the i-on control units support the 703r

transmitter.

For Users

1. Users can edit their own partition assignments for FOB-2W-4B.

i-on Range

Page iii

2. A user can now make only four attempts (instead of 10) before code lockout. After four

attempts the system generates a tamper condition.

3. A Duress Code user is blocked from all menus. A Duress code can only set/unset

system. A Duress code cannot have a prox tag or any remotes or HUDs.

4. Using a Duress code does not prevent other HUDs from starting an alarm.

5. A user can now set other partitions when the calendar set warning timer is running.

They do this by pressing the menu key, and the system shows them the normal setting

options.

6. An External Warning Device fault now prevents setting and cannot be overridden when

configured for EN50131 Grade 3. This fault can only be overridden for Grade 2.

7. For the Master User, Calendar Set now has two new warning timer options, see

“Partitions/Setting Options Menu” below.

8. A Master User can now make a test call to the ARC. This new feature helps installers

to clear PSTN alarm fail and line fail conditions without attending the site.

For Installers:

1. The i-kp01 ABCD LEDs now show the set status in partitioned systems with four

partitions or less (i-on40 and i-on30).

Detectors/Devices Menu:

1. There is a new HUD fault zone type.

2. The Ext PSU AC fail, Ext PSU battery fault, Ext PSU fault, WD fault and HUD fault

zone types are not available on radio devices.

3. There is a new Reset attribute for zones connected to shock and vibration sensors.

4. Tampers on Fire or Technical Alarm zones now cause an internal alarm instead of an

alert.

Partitions/Setting Options Menu:

1. Calendar Set now has two warning timer options: “Warning Time" and "Warning Tone".

Outputs Menu:

1. Output type "HUA confirm" now triggers on any two qualifying events. (two HUAs or

HUA plus tamper in any order).

2. There is a new output type: “Burg confirmed”. This output triggers on any two qualifying

events (two Normal Alarms or Normal Alarm plus tamper in any order).

(These modifications are to help ARCs which cannot correctly differentiate between

confirmed Burgs/HUA using existing outputs and messages.)

3. A Failed soak test no longer contributes to a General Fault.

4. The A/C Fail output type now restores as soon as the fault clears, and does not wait for

the user to acknowledge/clear the fault.

System Options Menu:

1. There is a new option “2-way Set Instant” in User Access.

2. There is a new option “Remote needs entry” for a part set.

3. The entry alarm delay has changed from 45s to 30s.

Communications Menu:

1. Fast Format now has three new channels to provide separate signals for Duress, HUA

confirm and Burg confirm.

2. The HUD/HUA SIA/CID report codes have been corrected:

i-on Range

Page iv

Zone PA = SIA "PA", CID "120"

User RF PA = SIA "PA", CID "120"

Keypad PA (dual keys) = SIA "PA", CID "120"

Duress Code = SIA "HA", CID "121"

3. Automatic Remote Diagnostics is now available the for i-on30EX/D, i-on40, i-on50EX/D

and i-on160EX. (Please note that this must be activated within Downloader by a

Eaton’s Security Business External Support Manager.)

Changes to Defaults:

1. Unset Comms now defaults to Enabled.

2. Fast Format channels 6 and 8 now default to Tamper and General Fault respectively.

3. Selected plug by outputs now default as follows:

4. Output 6 – Tamper, Output 8 – General Fault, Output 11 – Technical Alarm, Output 12

– Alarm Abort.

For –EUR panels Output 5 now defaults to Zone Omit (setting).

5. Default settle time is now 15 seconds.

New In Issue 7 (S/W version 4.03 with new keypads)

New Hardware

1. Control units now support KEY-KPZ01, KEY-KP01 and KEY-K01. The keypads have

new enclosures.

2. KEY-KPZ01 has an internal prox reader and connections for and external prox reader

(KEY-EP), two zones and one output.

3. KEY-KP01 has an internal prox reader and connections for an external prox reader

only.

4. KEY-K01 has no internal prox reader, no zones or outputs.

For Installers

Detectors/Devices Menu

1. The Wired Keypads menu allows you to enable/disable the zones and external prox

reader provided by the KEY-KPZ01, or external prox reader on the KEY-KP01. In

addition, you can also enable/disable the LEDs and set the display brightness for the

KEY-KPZ01, KEY-KP01 and KEY-K01.

Communications Menu

1. A HUA confirm code is now available in CID/SIA reporting.

New In Issue 8 (S/W version 4.04)

New Hardware:

1. The i-on expandable control units now support the EXP-WCC expander.

For Installers:

1. The ABCD LEDs are now linked to the ABCD keys. The ABCD LEDs glow whenever

all the partitions/part sets allocated to the keys are active.

Detectors/Devices Menu:

1. Zones connected directly to the control unit now appear on the keypad labelled as

“PAN<00<Znn” where nn is the zone number.

2. Log Only zones can now be allocated to Partitions, and can use the Chime attribute.

i-on Range

Page v

Partitions/Setting Options Menu:

1. Exit mode for Partition 2 and higher now defaults to “As Partition 1.”

Outputs Menu:

1. There is a new “pulsed” option available for outputs that previously did not have a

pulsed option.

2. Some output types previously available on the i-onEX range are now also available for

the i-on16.

3. Outputs connected to the control unit are now shown as “Panel>OPn” on the keypad,

where “n” is the number of the output.

System Options Menu:

1. There are new options for the radio keypad so that it can be configured to unset only

the partition(s) that have an entry timer running.

2. Mains Fail Delay has changed in operation.

Communications Menu:

1. Version 4.04 now supports Downloader over IP for all control units with an Ethernet

socket.

2. There is a new version of the SIA: EX SIA3 version 2. This option is designed to help

with some ARCs receiving unwanted “Mains Fail” signals.

3. There is now an additional Line Fail Response option available for the plug-by line fail

input.

4. The SMS over PSTN option now has the ETSI Protocol 1. (Not available on i-on16.)

5. Answer on one ring has a new option to accept three rings.

6. There is a new standalone virtual keypad called Virtual Keypad Instant (VKP Instant).

This can be enabled to allow user access.

Log Menu:

1. It is now possible to look through either the Mandatory Events for EN50131, or the

Non-Mandatory Events on their own. Alternatively you can still look through the whole

Log as one list.

i-on Range

Page vi

This page is intentionally blank.

i-on Range

Pagevii

Contents

About this Guide ............................................................................................................... ii

Other i-onEX Publications .......................................................................................................................... ii

A Note about screen displays .................................................................................................................... ii

Changes Since Release 4.00 ........................................................................................... ii

New in Issue 6 (S/W Version 4.03) ............................................................................................................ ii

New In Issue 7 (S/W version 4.03 with new keypads) .............................................................................. iv

New In Issue 8 (S/W version 4.04) ........................................................................................................... iv

Introduction ........................................................................................................................ 1

System Design ................................................................................................................. 1

The Control Unit ............................................................................................................... 1

Case ........................................................................................................................................................... 1

Printed Circuit Board .................................................................................................................................. 2

Bus Connections ........................................................................................................................................ 2

Zone Connections ...................................................................................................................................... 2

Output Connections ................................................................................................................................... 2

Keypads ..................................................................................................................................................... 3

Expanders .................................................................................................................................................. 5

Communications ........................................................................................................................................ 6

Programming the System .......................................................................................................................... 6

Part Setting or Partitioned System ............................................................................................................. 7

System Security Grade .............................................................................................................................. 7

System Capacities ..................................................................................................................................... 9

Basic Programming Procedures .................................................................................... 11

Programming Before Installation .................................................................................... 11

Built-in Web Browser Interface ................................................................................................................ 11

Entering and Leaving the Installer Menu ........................................................................ 11

From a Keypad ........................................................................................................................................ 11

From a Web Browser ............................................................................................................................... 11

To Enter the Installer Menu by Keypad: .................................................................................................. 12

Code Lockout – Excess Keys Tamper ..................................................................................................... 12

Transferring to Another Keypad ............................................................................................................... 13

To leave the Installer Menu at any time: .................................................................................................. 13

Important! Saving Changes ..................................................................................................................... 14

Defaulting the System .................................................................................................... 14

Restoring Factory Defaults ...................................................................................................................... 14

Defaulting Access Codes ......................................................................................................................... 17

Editing Text .................................................................................................................... 18

Resetting a System After an Alarm ................................................................................ 19

Programming Backlight and LEDs on KEY-K01/KP01/KPZ01 ....................................... 19

Adding Bus Devices ....................................................................................................... 21

The System Bus (i-on EX Control Units Only) ............................................................... 22

Device Addressing on the Bus ....................................................................................... 22

Bus Device Addresses ............................................................................................................................. 23

Detector Connection Point Addresses ..................................................................................................... 24

Output Numbering .................................................................................................................................... 25

Other Radio Device Addressing............................................................................................................... 26

Other Devices Connected to the Control Unit.......................................................................................... 26

Bus Scanning and Re-configuring ........................................................................................................... 26

Zone Numbering............................................................................................................. 27

Mapping Zones to Expanders .................................................................................................................. 27

Adding/Removing Expanders and Zone Numbering ............................................................................... 29

Zone 000 .................................................................................................................................................. 29

Numbering Zones on Keypads ................................................................................................................ 30

Processing Priority ................................................................................................................................... 32

Tampers and the Bus ..................................................................................................... 32

Installer Menu ................................................................................................................... 33

Installer Menu Options .................................................................................................... 44

i-on Range

Page viii

Detectors/Devices .......................................................................................................... 44

Detectors .................................................................................................................................................. 44

Expanders ................................................................................................................................................ 54

Wired Keypads ......................................................................................................................................... 57

Radio Keypads ......................................................................................................................................... 61

External Sirens ......................................................................................................................................... 62

Info Modules............................................................................................................................................. 63

WAMs ....................................................................................................................................................... 64

Outputs ........................................................................................................................... 64

Bell and Strobe ........................................................................................................................................ 65

Wired Outputs .......................................................................................................................................... 65

Control Unit Plug-By Outputs ................................................................................................................... 66

Radio Outputs .......................................................................................................................................... 66

Output Types............................................................................................................................................ 66

Programing Zone Follow Outputs ............................................................................................................ 73

Programming Zone Alarm Outputs .......................................................................................................... 74

Programming User Defined Outputs ........................................................................................................ 75

“Setting Options” and “Partitions” Menus ....................................................................... 75

Part Setting or Partitioned System? ......................................................................................................... 75

Options ..................................................................................................................................................... 77

Full Set Link ............................................................................................................................................. 82

Calendar Set ............................................................................................................................................ 83

System Options .............................................................................................................. 86

Wired Zone Type ..................................................................................................................................... 86

User Access ............................................................................................................................................. 87

User Reset ............................................................................................................................................... 88

Confirmation (EUR Variants) ................................................................................................................... 89

Confirmation (UK Variants) ...................................................................................................................... 90

Profiles ..................................................................................................................................................... 93

Masking .................................................................................................................................................... 94

Mask Override .......................................................................................................................................... 96

Language ................................................................................................................................................. 96

Restore Defaults ...................................................................................................................................... 96

Installer Name .......................................................................................................................................... 97

Installer Code ........................................................................................................................................... 97

Keypad Text ............................................................................................................................................. 98

Remote Needs Entry ................................................................................................................................ 98

Remote Entry Part Set ............................................................................................................................. 98

RKP Needs Entry ..................................................................................................................................... 98

RKP Entry Part Set .................................................................................................................................. 99

HUA Response ........................................................................................................................................ 99

Auto Rearm .............................................................................................................................................. 99

Panel Loudspeaker .................................................................................................................................. 99

Entry Alarm Delay .................................................................................................................................. 100

Abort Time.............................................................................................................................................. 100

Supervision ............................................................................................................................................ 100

Jamming ................................................................................................................................................. 101

Force Set ................................................................................................................................................ 101

Tamper Omit .......................................................................................................................................... 102

CSID Code (Anti-Code Reset) ............................................................................................................... 102

Silence Alerts ......................................................................................................................................... 102

Mains Fail Delay .................................................................................................................................... 103

Battery 2 ................................................................................................................................................. 104

Set Time and Date ................................................................................................................................. 104

Panel Tamper Return ............................................................................................................................. 104

Communications........................................................................................................... 104

ARC Reporting ....................................................................................................................................... 106

Unset Comms ........................................................................................................................................ 114

Speech Dialler ........................................................................................................................................ 114

SMS ....................................................................................................................................................... 117

Line Fail Response (For Plug-on or Built-in Module) ............................................................................. 120

Line Fail Delay (For Plug-on or Built-in Module) .................................................................................... 121

i-on Range

Page ix

IP Network (Own) ................................................................................................................................... 121

Downloading .......................................................................................................................................... 123

Plug-by ................................................................................................................................................... 126

Test .............................................................................................................................. 127

Sirens and Sounders ............................................................................................................................. 127

Wired Keypad......................................................................................................................................... 128

Radio Keypads ....................................................................................................................................... 128

Expanders .............................................................................................................................................. 128

Walk test ................................................................................................................................................ 129

Zone Resistances .................................................................................................................................. 130

Signal Strengths ..................................................................................................................................... 131

Outputs ................................................................................................................................................... 131

Remotes ................................................................................................................................................. 132

User Hold Up Alarms ............................................................................................................................. 132

Prox Tags ............................................................................................................................................... 132

ARC Reporting ....................................................................................................................................... 133

Speech Dialler ........................................................................................................................................ 133

PSU Current ........................................................................................................................................... 133

Battery(s) ................................................................................................................................................ 134

Locate Panel .......................................................................................................................................... 134

Locate Bus Device ................................................................................................................................. 134

Using LEDs for Bus Diagnostics ............................................................................................................ 134

Other Diagnostic LEDs .......................................................................................................................... 135

View Log ...................................................................................................................... 135

Mandatory and Non-Mandatory Log Events .......................................................................................... 135

How the Log Displays User Identities .................................................................................................... 135

Downloader and the Log ........................................................................................................................ 136

Logging Tamper Events ......................................................................................................................... 136

Logging Software Updates ..................................................................................................................... 136

About ............................................................................................................................ 136

Panel ...................................................................................................................................................... 136

Expanders .............................................................................................................................................. 136

Keypads ................................................................................................................................................. 136

PSU ........................................................................................................................................................ 137

Comms ................................................................................................................................................... 137

Zone Mapping ........................................................................................................................................ 137

Appendix I: ARC Communication Formats ................................................................. 138

Fast Format .................................................................................................................. 138

Contact ID .................................................................................................................... 138

SIA 1, SIA 2, SIA 3 and Extended SIA 3 ...................................................................... 138

Extended SIA3 V2 .................................................................................................................................. 139

Appendix II: Programming a Common Area ................................................................ 140

Installation and Programming ....................................................................................... 140

Zone Programming ................................................................................................................................ 141

Partition and Other Programming .......................................................................................................... 141

User Programming ................................................................................................................................. 142

User Operation ............................................................................................................. 142

To set: .................................................................................................................................................... 142

To Unset: ................................................................................................................................................ 142

Appendix III: Using A WAM As A Repeater ................................................................. 144

Introduction .................................................................................................................. 144

Before You Begin ......................................................................................................... 144

Teach the Expander the Identity of the WAM ............................................................... 145

At The Keypad: ...................................................................................................................................... 145

On the WAM:.......................................................................................................................................... 146

At the Keypad ........................................................................................................................................ 146

Teach the WAM the Identity of the Detectors ............................................................... 146

Deleting Devices .......................................................................................................... 147

Appendix IV: Programming a 762 or 768/769 as an Output Module .......................... 149

i-on Range

Page x

Introduction .................................................................................................................. 149

Before You Begin ................................................................................................................................... 149

Set Up the 762 or 768/769 ........................................................................................... 149

Enter Programming Mode ...................................................................................................................... 149

Set the Channels to Output Module Mode ............................................................................................. 149

Disable infrared learning ........................................................................................................................ 150

Set to manual learn ................................................................................................................................ 150

Select channel ....................................................................................................................................... 150

Teach the Control Unit to the 762r or 768r/769r ........................................................... 150

At the Keypad: ....................................................................................................................................... 150

At the 762r (or 768r/769r) ...................................................................................................................... 151

At the Keypad ........................................................................................................................................ 152

Appendix V: Changing i-rk01 From Four to Six Digit Access Codes ........................ 153

Appendix VI: Using a 703 Transmitter ......................................................................... 154

Appendix VII: Log Messages ........................................................................................ 155

Log Events ................................................................................................................... 155

Index ............................................................................................................................... 160

i-on Range

Page 1

Introduction

System Design

The i-on range of control units for hybrid wired/wirefree alarm systems are intended for,

domestic, commercial or industrial use. The range is designed to support a wide spread of

alarm system sizes. To increase the size of the alarm system the i-onEX control units

allow the Installer to connect expanders and keypads to a single “data bus” which carries

all the data between the control unit and its peripherals.

The control unit PCB provides connections for wired zones and a number of outputs. The

Expanders provide connections to either extra wired zones and outputs, or radio detectors

and radio outputs. Both wired and radio devices can exist in the same alarm system. The

single bus cable also allows the installer to connect keypads, output modules or extra

power supplies wherever they are needed.

The Control Unit

Case

All i-on control units are housed in an individual case that provides space for the control

unit’s PCB, power supply and one or more backup batteries. The cases are designed for

vertical mounting on a wall, and provide three or more fixing points.

The i-on160EX, i-on50EX and i-on30EXL cases are made of coated steel and can be

butted up to side walls or a ceiling without blocking the opening or closing of its lid. The

case lid is fixed by a single screw, and can be hung from the case back when open. The

back of the case provides pre-cut holes for cable access, and stands off from the mounting

surface to allow cables to pass behind.

The i-on30EX case is also made of coated steel, and has an “all-over” lid fixed on by a two

screws.

The i-on16 and i-on40 cases are made from ABS plastic.

Battery Backup

The i-on160EX case provides space for two 17Ah backup batteries. Each battery has its

own connector on the control unit PCB, and is charged by the control unit while mains

power is present.

It is possible to run the system with a single backup battery (although the resulting standby

time may not meet the Grade 2 or Grade 3 requirements). If you chose to use a single

battery, then you should connect the battery to connector “BATT1” and program the

control unit to suppress alerts that Battery 2 is missing, see page 104.

The i-on50EX and i-on30EXL provide space and a connector for one 17Ah battery.

The i-on16, i-on30EX and i-on40 provide space and connectors for one 7Ah battery.

Back tamper/Lid tamper. In the i-on160EX, i-on50EX i-on40 and i-on16 the back of the

case provides a plastic shrouded slot through which the Installer can fit the combined back

tamper/lid tamper switch. This switch is mounted on a metal blade that slides through the

slot and touches the mounting surface. Once fitted and connected to the PCB, removing

the lid or prising the case from the wall activates the switch.

In the i-on16 and i-on30EX the lid tamper is a switch mounted on the main PCB.

Introduction i-on Range

Page 2

Printed Circuit Board

All of the control unit functions and connectors are provided by a single PCB. In the i-

on30EX/i-on30EXD, i-on30EXL/i-on30EXDL, i-on50EX/i-on50EXD and i-on160EX a

plastic PCB carrier holds the PCB within the case.

Bus Connections

30 50 160.

The i-on EX range of control units provide connectors for one four-wire bus cable. All

keypads, expanders and other equipment connect to the same bus. The cable can be run

as one single line, or as a three or four armed star branched at the control unit. See the

relevant Installation Guide for details of bus configuration, maximum bus length and

cabling type.

Zone Connections

The control unit itself provides the following connections for wired zones:

Control Unit

CC Zones

FSL Zones

i-on40

8 x 4-wire

16 x 2-wire

16

i-onEX

5 x 4-wire

10 x 2-wire

10

These zones can be either all Closed Circuit (CC) or all Fully Supervised Loop (FSL). The

Installer can select the zone wiring type during initial commissioning, or at any time after.

The Installer can make the wiring type of expanders either CC or FSL, independent of the

wiring type of the zones on an i-onEX control unit. Note that there are no wired zones on

the i-on16 control unit.

Output Connections

Transistor Outputs

The control unit provides connectors for programmable transistor outputs which can be

used to control external equipment. The outputs are normally switched negative, from 12V

to 0V on activation. In this mode each output can sink up to 500mA from a dc source.

The installer can program these outputs to be switched positive (from 0V to 12V on

activation). In this mode the outputs can deliver up to 500mA to an external load.

See page 9 for the number of transistor outputs available on each control unit.

Relay Outputs

40 50 160.

The i-on40, i-on50EX and i-on160EX control unit also provide sets of connectors for relay

outputs, providing voltage free changeover contacts. Relay outputs are programmable by

the Installer.

See page 9 for the number of relay outputs available on each control unit.

Digital Communicator Outputs (Plug-by Outputs)

30 40 50 160.

A set of pins on the control unit PCB provide programmable outputs designed to control a

separate digital communicator.

By default each output is switched negative (switched from +12V to 0V when active).

When at 0V each communicator output can sink up to 100mA.

The installer can program these outputs to be switched positive when active (switched

from 0V to +12V). When at +12V each output can provide up to 50mA to an external load.

i-on Range Introduction

Page 3

See page 9 for the number of relay outputs available on each control unit.

USB Port

30 40 50 160.

The mini-USB port allows an Installer to program the control unit through a USB cable

from a PC to the control unit. The PC must be running Eaton Security Business’s

Downloader.

The USB port also allows an Installer to apply software updates to the control unit or, in

European versions, install alternate language text files for the keypad display. To do this

the Installer must run Eaton Security Business’s i-on Updater software on the connected

PC.

The Downloader and i-on Updater software is available to registered users from the

Touchpoint Product Support/Downloads pages on www.coopersecurity.co.uk.

Ethernet Port

40 50 160.

The Ethernet port also allows a local connection to a PC. The Ethernet connection is

designed to allow an Installer to program the control unit through a series of web pages

presented by a built-in web browser interface running on the control unit. Eaton’s Security

Business recommends that you use Internet Explorer 8 or higher to browse the pages.

With software release 4.04 and higher Downloader can also use the Ethernet port to

program control units from a PC.

External Bell/Strobe Outputs

30 50 160.

The control unit has one external bell output to drive standard Self-Activating Bell (SAB) or

Self-Contained Bell (SCB) modules, and one output to activate a strobe. Expanders also

provide connectors for additional external sounders. See the Installation Guide for each

product for details of maximum current available for external bells.

Auxilliary Tamper

50 160.

The i-on50EX and i-on160EX control units also provide “Aux Tamper” terminals for

connecting the tamper wiring of any external device (other than keypads and expanders)

that needs tamper protection.

Extension Loudspeaker Connectors

If required the Installer can connect 16 Ohm extension loudspeakers to increase the

audibility of setting and unsetting tones. Each expander also provides connectors for one

16 Ohm extension loudspeaker. Note that you must not connect another loudspeaker in

parallel to the same connectors.

Keypads

In alarm systems built around i-on control units all the keypads connect directly to the

system bus.

The i-on control units with Release 4 software can use a range of keypads, including the i-

kp01, KEY-K01, KEY-KP01 and KEY-KPZ01.

Users can set and unset the system or partitions from the keypad, either by keying-in

access codes or presenting a prox tag (if the keypad has a prox tag reader).

Introduction i-on Range

Page 4

Provided that they are in separate partitions, the control unit can respond to several

keypads in use at the same time. Within each partition, the control unit responds to just

one keypad at a time. The number of simultaneous keypad sessions each control unit can

handle at any one time is:

i-on160EX five

i-on50EX five

i-on30EX two

i-on40 four

1-on16 one

In a part setting system (one not using partitions) the control unit responds to just one

keypad at a time.

The Installer can also program the system from any keypad. When the Installer is logged

into the system all other keypads are locked out and their displays show the message

“Installer on site” if a user tries to access the system.

User Interface

All keypads have:

A two line by 20 character backlit LCD display

Four LEDs that can be programmed to show the setting status of the system. To

comply with EN50131 the installer can disable these LEDs in order to hide the state of

the system.

An illuminated four way switch (the “navigation key”) that is used to navigate through

menus

LEDs behind the navigation key that show the fault status of the system.

A numeric keypad for entering access codes and keying in text.

Dedicated A, B, C and D keys that can be programmed to set individual partitions, part

sets, or allocated to control outputs.

Keys for “yes”, “no”, menu and unset functions.

HUA keys that can be used to start a hold up alarm.

The keys are backlit by LEDs within the keypad. The backlighting for both the display and

keys can be programmed to different intensities and timing.

The i-kp01

i-on control units can use i-kp01 keypads with keypad firmware version 2.00 and above.

The installer can disable the ABCD LEDs by removing the appropriate jumpers in each

keypad (see the Installation Guide for each control unit).

Separate jumpers allow the installer to adjust the brightness and timing of the backlighting.

The KEY-K01/KP01/KPZ01

From control unit software version 4.03 onwards the i-on range control units can also use

the KEY-K01, KEY-KP01 and KEY-KPZ01 keypads. All of these keypads provide similar

functions to the i-kp01 and can be substituted freely for i-kp01’s on any i-on control unit

running software version 4.03.09 or higher.

The KEY keypads have slight changes in their user interface compared to the i-kp01:

The KEY- keypads do not have separate ABCD LEDs. The ABCD keys themselves

now glow whenever the setting state of the system corresponds the action

programmed for the key (see page 58).

i-on Range Introduction

Page 5

The navigation key has been redesigned so that the key itself glows red or green to

show system status.

The LCD display is slightly smaller in order to provide space for a customisable label.

This label can be printed with installer details (for example logo or telephone number).

Please contact the Eaton’s Security Business marketing department for more details.

All the KEY- keypads allow the installer to program the behaviour of the backlight, the

illuminated ABCD keys and the LEDs in the navigation key. Instead of using jumpers (as

on the i-kp01) the new keypads now have their own local programming menu, see page 19

for details.

In the i-on EX panels the keypad backlights, ABCD/Navigation key LEDs can be

programmed from the Installer menu, (see page 59). The i-on16 and i-on40 can also

program the keypad backlights from the control unit, but to change the behaviour of the

ABCD/Navigation key LEDs you must use the keypad’s local programming menu.

The differences between the KEY-K01, KEY-KP01 and KEY-KPZ01 are as follows:

The KEY-K01 does not have an internal prox reader.

The KEY-KP01 has an internal prox reader and terminals for connecting and external

prox reader (the KEY-EP).

The KEY-KPZ01:

Has an internal prox reader and terminals for connecting an external prox reader

(the KEY-EP).

Provides terminals for two zones.

Provides terminals for a single output.

Note: Do not fit any keypad with an internal prox reader closer than one meter to any other

type of prox reader. This includes other keypads with prox readers, external prox

readers such as the KEY-EP, or prox readers used by other systems (for example

access control systems). If you mount prox readers closer together than one meter

(including on the other side of walls) then the two prox readers will interfere and may

not work correctly.

Engineering Keypad

30 50 160

An Engineering Keypad is a modified i-kp01 that can be plugged into a dedicated

connector on the control unit PCB or any of the expanders. An Engineering Keypad does

not need to be addressed, and will always be recognised by the control unit as an

Engineering Keypad.

You can use an Engineering Keypad to program the system without being tied to any of

the installed keypads. If you wish to move an Engineering keypad from one connection

point to another then you can do so without removing power from the system.

Expanders

30 50 160

Wired Expander

The EXP-W10 wired expander provides connections for:

Either ten FSL zones, or five 4-wire CCL zones, or ten 2-wire

CCL zones.

One loudspeaker

Four wired programmable outputs

The EXP-WCC wired expander in general provides the same number

of connections as the EXP-W10, but in addition also provides

terminals for ten 4-wire CCL zones instead of five.

Introduction i-on Range

Page 6

Radio Expander

The EXP-R10 radio expander provides 10 zones for radio detectors.

The EXP-R30 provides 30 zones for radio detectors on an i-on160EX

or i-on50EX. When fitted to an i-on30EX the EXP-R30 provides 20

zones. In addition each radio expander provides channels for: two

radio keypads, two external radio sounders and two Wireless

Accessory Modules (WAMs) (Note that the i-on30EX supports only

one WAM.). Each radio expander also provides wired connections for

a Loudspeaker. The maximum number of expanders, detectors,

keypads and WAMs depends on control unit type, see page 9.

Note: The total number of radio detectors that can be handled by an

i-onEX control unit depends partly on the density of radio

transmitters within a given volume. If there are more than 30

transmitters within 10 meters radius of an expander then some

mutual jamming may occur. Please read “Guidance Notes For

Radio Alarm System” available from www.coopersecurity.co.uk.

Remote Power

Supply

The EXP-PSU remote power supply provides extra power and more

space for standby batteries for larger alarm systems. The EXP-PSU

also provides connections for either 10 FSL zones, or five 4-wire CCL

zones, or ten 2-wire CCL zones, plus a loudspeaker and four wired

programmable outputs.

The EXP-PSU connects to the system bus, and communicates with

the control unit in the same way as a wired expander.

Communications

Each of the i-on range of control units provide sockets for a single plug-on communication

module. For the i-on40 and i-onEX range the available modules are:

i-dig02

A PSTN module that allows the control unit to report alarm information using standard

protocols such as Fast Format, SIA and Contact ID. This module also allows remote

maintenance over the PSTN and sending SMS messages.

i-sd02

A speech dialler and public switched telephone network (PSTN) module that

allows the control unit to send recorded speech messages and also report

alarm information using standard protocols such as Fast Format, SIA and

Contact ID. This module also allows remote maintenance over the PSTN and

sending SMS messages.

i-gsm02

A GSM module that allows speech messaging, alarm reporting and SMS text

messaging over the GSM mobile phone network.

For the i-on16 the i-sd01 provides a speech dialler and public switched telephone network

(PSTN) module with the same features as the i-sd02.

To ensure that the i-on16, i-on30EX, i-on40, i-on50EX and i-on160EX comply with

EN50131 you must fit a suitable communicator to meet the Security Grade required.

The i-on30EXD and i-on50EXD also have built-in digital communicators. Note that the

communicators are disabled if you fit any of the above plug-on modules.

Programming the System

As an installer you can program the system in any of three separate ways:

a) From the keypad.

i-on Range Introduction

Page 7

b) 30 40 50 160 Using Downloader software on a PC or laptop connected to the

control unit either over the PSTN, or via the USB port, or via the Ethernet port. (This

option is not available on i-on16.)

c) 40 50 160 From a PC or laptop connected to the control unit via Ethernet cable,

and using a web browser (IE 8 recommended). This option is not available on the i-

on16 or the i-on30EX.

This manual describes programming the control unit from a wired keypad. The settings

and options provided through the web server or Downloader have the same functionality

as those provided through the keypad.

Part Setting or Partitioned System

An i-on control unit offers two basic ways of behaving as an alarm system:

Part Set Mode. In Part Set Mode the control unit can set in one of four ways: either Full

set or three varieties of Part Set. In Full Set the control unit pays attention to all detectors.

In each of the three Part Sets, the control unit ignores all detectors that do not have the

appropriate Part Set attribute enabled (see page 51 ).

Partition Mode. 30 40 50 160 In Partition Mode the control unit provides the

equivalent of a set of smaller, independent alarm systems. Each system is a “Partition” of

the whole. You can allocate any set of zones to each Partition. Each Partition can have a

Full Set level and one Part Set level. During programming the installer can allocate

keypads, sounders or outputs to any of the partitions.

The fact that each zone can belong to more than one Partition may produce un-anticipated

results for the users of the system. When designing a system remember that a zone will

only be armed when ALL of the partitions that it belongs to are set. If a user unsets any of

the partitions that a zone belongs to, then the control unit will disarm the zone. If a user is

not aware of all the partitions that use the zone they may not realise that a zone is

disarmed when they believe it should be armed.

The i-on160EX supports 20 partitions, the i-on50EX supports five, and the i-on30EX and

i-on40 support four partitions.

System Security Grade

All i-on control units are suitable for use in systems conforming to Security Grade 2

requirements.

The i-on50EX/i-on50EXD and i-on160EX can be used in either Security Grade 2 or 3

alarm systems.

50 160 During initial power up (and if you reset a system to factory defaults) the i-

on50EX/i-on50EXD and i-on160EX control units provide an opportunity for you to set

various system options in one step in order to program the system for either Security

Grade 2 or Security Grade 3.

Grade 2

The system uses four digit user codes, turns Masking OFF, defaults User

Reset – Zone Tampers to “Yes”, and ensures that “Tampers” are

communicated as “Alarms”.

Grade 3

The system uses six digit user codes, turns Masking ON, defaults User Reset

– Zone Tampers and User Reset – Zone Alarms to “No” (Installer). The

system communicates tampers as tampers.

You can override any of the settings by selecting individual options in other parts of the

Installer Menu. Note that if you do so then the system may no longer comply with the

selected Grade.

Introduction i-on Range

Page 8

User Codes

When using four digit access codes, the default Installer code is “7890” and the default

User 001 (User 01) code is “1234”.

When using six digit access codes the default Installer code is “567890”, and the default

User 001 (User 01) code is “123456”.

i-on Range Introduction

Page 9

System Capacities

Main Software Differences

i-on16

i-on30EX

i-on40

i-on50EX

i-on160EX

Max No Zones

16

30

40

50

160

Users:

16

50

100

500

Part Sets (In part set mode)

3

Partitions: (see Note 3)

n/a

4

5

20

Bus devices: (see Note 1)

None

10

None

20

45

Max No Wired Outputs

(non plug-by)

4

30

4

50

160

Max No Radio Outputs

(see Note 5)

4

30

8

50

160

Radio sounders: (see Note 2)

2

4

5

20

Radio Keypads: (see Note 2)

2

4

5

20

WAMs: (see Note 2)

0

1

2

5

20

Mandatory log events

250

750

500

1,500

Non-mandatory log events

15

100

250

500

Calendar Set events

0

5

20

Calendar Set Exceptions

0

30

EN 50131 Security Grade

2

2 or 3

Web browser interface

No

Yes

ARD

No

Yes

Main Hardware Differences

i-on16

i-on30EX

i-on40

i-on50EX

i-on160EX

Wired zones on control unit

(see Note 4)

None

10

16

10

Networks (Bus)

None

1

None

1

Dedicated Sounder / strobe outputs

on board

No

Yes,

1+1

No

Yes,

1+1

Yes,

1+1

Panel Outputs (Relay)

0

2

1

2

Panel Outputs Transistor

4

1

2

Plug-by outputs

0

12

16

Ethernet port

N

Y

Batteries (see Note 6)

1*7Ah

1*17Ah

2*17Ah

On Board Loudspeaker Ports

1

2

Power Available

1.0A

1.5A

3A

Control unit case

Plastic

Steel

Plastic

Steel

Built-in communicator

No

EXD/

EXDL

No

EXD

No

Introduction i-on Range

Page 10

Notes:

1. Shared between expanders and keypads. The i-on16 can have two keypads and

the i-on40 four keypads. Neither the i-on16 nor i-on40 can use expanders.

2. Two per expander for i-onEX control units.

3. In partition mode. Each partition has one part set within it.

4. i-on40: Either 16 in FSL mode OR eight in 4-wire CC mode. 24 radio zones.

5. i-on16 and i-on40 have four wired outputs. The i-on16 has four radio outputs while

the i-on40 has eight. All –EX control units have radio outputs provided by EXP-

R10/EXP-R30 expanders and 762r, 768r or 769r receivers.

6. The i-on30EXL can take one 17Ah battery.

Page is loading ...

Eaton i-on Series Engineering Manual

Eaton i-on Series Engineering Manual

Related papers

Other documents