Response ML6 Installation and Operating Instructions

Brand: Response

Model: ML6

Type: Installation and Operating Instructions

Response ML6 is a single-room PIR alarm with remote control, which can be either wall-mounted or used freestanding for portable use. It features a passive infrared (PIR) detector, which detects movement by sensing changes in infrared radiation levels caused by a person or animal moving within the device's field of vision. The system has two operating modes:

Alarm Mode: In this mode, the device will produce a constant high-volume alarm sound when triggered.
Chime Mode: This is a low-security feature that will produce a door-chime sound when the alarm is triggered.

Alarm Mode: In this mode, the device will produce a constant high-volume alarm sound when triggered.
Chime Mode: This is a low-security feature that will produce a door-chime sound when the alarm is triggered.

ML6 - Single Room PIR Alarm

with Remote Control

Installation and Operating Instructions

These instructions should be retained in a safe place for future reference.

INTRODUCTION

The Alarm can be either wall mounted using the

bracket supplied or used freestanding for

portable use.

The Remote Control is used to ARM and DISARM

the system. The Remote Control operates using

Infra Red so it must be pointing directly at the PIR

Alarm to function.

A Passive Infra-Red (PIR) detector is designed to

detect movement in an area by detecting changes

in infra-red radiation levels caused for example

when a person/animal moves within the devices

field of vision.

The system has 2 operating modes: ALARM and

CHIME. Chime Mode is a low security feature

that will produce a door-chime sound when the

alarm is triggered. In Alarm Mode the device will

produce a constant high volume alarm sound

when triggered.

Safety: Always follow the manufacturers advice

when using power tools; steps, ladders etc. and

wear suitable protective equipment (e.g. safety

goggles) when drilling holes etc.

Before drilling holes in walls, check for hidden

cables and pipes, the use of a cable/pipe locater

may be advisable if in doubt.

The use of ear protection is advisable when

working in close proximity to the Siren due to the

high sound level produced by this device.

Do not use in wet locations.

INSTALLATION

The alarm is designed to be wall mounted with the

ball and socket mount (included). The ball and

socket mount will provide the flexibility to aim the

motion sensor in a particular direction.

1. Select your desired location for the alarm, such

as the corner of a room. This will provide

maximum coverage.

Note: The sensor has a 6m. detection zone,

with approximate angles of 110° horizontal

and 70° vertical. Recommended installation

height is 1.8 - 2.4m.

2. Secure the ball and socket mount to the wall

using either the provided wall anchors or by

screwing directly into a wall stud. Once

installed securely on the wall, slide the insert

bracket of the mount into the back of the unit

and lock in place. The mount will click when

secured to the alarm.

INSTALLING BATTERIES

Installing batteries in the Alarm:

The Motion Sensing Alarm requires three AA

Alkaline batteries (not included).

The battery compartment is located on the back of

the unit.

Remove the battery compartment screw and slide

off the cover in the direction of the open arrow.

2. Insert three AA Alkaline batteries (not included).

Take care to note the polarity diagram inside the

battery compartment.

3. Replace battery compartment cover and secure

screw.

Installing the battery in the Remote Control:

The Remote Control is supplied fitted with one

CR2032 battery. Average battery life for typical

usage is up to one year.

The battery compartment is located on the back of

the unit.

1. Slide offthe battery compartment cover located

on the back of the Remote Control.

2. Carefully remove the battery isolation tab fitted.

3. Replace cover.

LOW BATTERY INDICATOR

The Remote Controlled Motion Sensing Alarm has

a low battery indicator light. When the batteries

need to be replaced, the indicator light will flash

slowly. Average battery life for typical usage is up

to one year.

LINKING THE REMOTE CONTROL

TO THE ALARM

Make sure you have installed the batteries before

proceeding.

1. Remove the screw from the battery

compartment cover and slide off the cover in

the direction of the open arrow. Locate the

LEARN button.

2. Press the LEARN button.

3. Immediately point the remote control towards

the front of the the alarm unit and press the

ARM button. The alarm will sound a single short

tone, and the light will stop flashing to confirm

the remote has been linked to the Alarm. The

alarm unit will now respond to the remote.

4. Replace the battery compartment cover on the

main alarm unit and secure the screw. The

alarm is now in standby mode.

OPERATING IN ALARM MODE

1. Locate the ALARM/CHIME switch on the side

of the alarm.

2. Slide the switch to ALARM mode.

Arming the Alarm:

1. Point the remote control at the front of the alarm

and press the ARM button. The alarm will sound

a tone and the red indicator light will flash. There

will be a 45 second exit delay before the unit is

armed. The delay allows time for you to leave

the protected area without triggering the alarm.

2. When motion is detected, the alarm unit

will sound a short time and a red light will

flash. The alarm will activate after 30 seconds.

The siren will sound for 30 seconds (unless

disarmed by the remote) and then turn off.

After 15 seconds the alarm will check for motion.

If motion is detected, the siren will sound again.

The cycle will repeat until the unit is disarmed

with the remote.

Disarming the Alarm:

1. When returning to the protected area, the unit

will beep once if motion is sensed.

2. Point the remote control at the front of the

alarm unit and press the DISARM button within

30 seconds to disarm the alarm.

If the disarm button is not pressed within 30

seconds, the alarm will sound. During the entrance

delay, the red indicator light will flash. Use the

remote control at any time to deactivate the alarm.

Note: To test, a cloth can be used to cover the

alarm to reduce risk of hearing damage.

OPERATING IN CHIME MODE

The chime is used to notify you when motion is

sensed in the area.

1. Locate the ALARM/CHIME switch on the side

of the remote.

Slide the ALARM/CHIME switch to CHIME mode.

Activating the Chime:

To activate the chime point the remote control at the

alarm and press the ARM button. The chime will

sound immediately and again when motion is sensed.

Deactivating the Chime:

To deactivate the chime point the remote control at

the alarm and press the DISARM button.

Panic Feature:

For immediate alarm with no delay, point the

remote at the front of the alarm and press and hold

the ARM and DISARM buttons on the remote

control for 2 seconds. To turn off the panic alarm,

point the remote at the front of the alarm and press

the DISARM button.

TESTING MOTION SENSOR

OPERATION

1. Set the remote to CHIME mode and press the

ARM button; the chime will sound once.

After the initial chime, wait 15 seconds and then

wave your hand in front of the sensor. If the chime

sounds immediately, the sensor is working correctly.

3. To discontinue the test, point the remote at the

front of the alarm and press DISARM. Set the

remote to ALARM mode.

MAINTENANCE

To clean the unit housing, use a soft cloth slightly

dampened with water and wipe dry. Do not use

chemical agents as this may damage and

discolor the unit.

Warning:

Risk of personal injury

●

Prolonged exposure to alarm siren may cause

permanent hearing loss.

Battery Warning:

●

Remove batteries before storing the Alarm for

extended periods.

●

Batteries may leak harmful liquids or ignitable

materials or explode causing injury and product

damage.

●

Do not mix old and new or other battery types.

●

Replace all batteries at the same time.

●

Replace fully discharged batteries immediately.

●

Do not put the button cells in your mouth as this could

impair your health. Keep out of reach of young

children as they could swallow these and choke.

For indoor use only; do not use in wet locations.

TROUBLE SHOOTING

Remote Control not operating

●

Batteries low, flat, missing or are incorrectly fitted.

●

Infra-Red Transmitter LED obscured.

●

Remote Control not pointing directly at PIR

Alarm Unit

PIR Alarm Unit not operating

●

Batteries low, flat, missing or are incorrectly fitted.

●

House code not programmed.

PIR causing false alarms

●

PIR badly positioned, (e.g. in direct sunlight,

draughts and above a radiator etc.).

DISPOSAL AND

RECYCLING

At the end of their useful life the

packaging and product should be

disposed of via a suitable Recycling

Centre.

Do not dispose of with your normal household

waste.

DO NOT BURN.

GUARANTEE

Novar ED&S undertakes to replace or repair at its discretion goods (excluding non rechargeable batteries)

should they become defective within 1 year solely as a result of faulty materials and workmanship.

Understandably if the product has not been installed, operated or maintained in accordance with the

instructions, has not been used appropriately or if any attempt has been made to rectify, dismantle or alter

the product in any way the guarantee will be invalidated.

The guarantee states Novar ED&S entire liability. It does not extend to cover consequential loss or damage

or installation costs arising from the defective product. This guarantee does not in any way affect the

statutory or other rights of a consumer and applies to products installed within UK and Eire only.

If an item develops a fault, the product must be returned to the point of sale with:

1. Proof of purchase.

2. A full description of the fault.

3. All relevant batteries (disconnected).

Response is a trademark of Novar ED&S.

CUSTOMER HELPLINE

Most issues can be solved over the phone in a few minutes.

Please contact our Helpline Team on the number below for any installation

and general advice regarding our products:

0844 736 9149

Lines open 9.00am to 5.00pm, Monday to Friday. Calls charged at service providers national rate.

Novar Electrical Devices and Systems Limited. (A Honeywell Company)

The Arnold Centre, Paycocke Road, Basildon, Essex SS14 3EA. UK

www.friedland.co.uk

Response ML6 Installation and Operating Instructions

Brand: Response

Model: ML6

Type: Installation and Operating Instructions

Alarm Mode: In this mode, the device will produce a constant high-volume alarm sound when triggered.
Chime Mode: This is a low-security feature that will produce a door-chime sound when the alarm is triggered.

Download PDF

report

Response ML6 Installation and Operating Instructions

Response ML6 Installation and Operating Instructions

Related papers

Other documents