Konica Minolta EP2050 User manual

EP2050

Thank you for choosing Minolta.

This operator’s manual explains how to operate the copier and replenish its

supplies. It also gives some troubleshooting tips as well as general precautions to

be observed when operating the copier.

To ensure the best performance and effective use of your copier, read this manual

carefully until you familiarize yourself thoroughly with its operation and features.

After you have read through the manual, keep it for ready reference.

Please use this manual as a quick and handy reference tool for immediately

clarifying any questions which may arise.

1136O053AA

i

Contents

Chapters 1 through 3 contain the basic information for making copies.

Be sure to read these chapters before attempting to use your copier.

Using This Manual

Organization viii

Page Organization ix

Terms and Symbols for the Type of Originals and Copy

Paper x

Chapter 1 Safety Notes 1

1. Installing The Copier

Installation Site 2

Power Source 2

Grounding 2

Space Requirements 3

2. Precautions for Use

Operating Environment 4

Using the Copier Properly 4

Care of Copier Supplies 4

Moving 5

ii

Chapter 2 First Things to Know

about EP2050 7

1. System overview 8

2. Copier parts and Accessories

Outside Your Copier 10

Inside Your Copier 12

Paper Feed Cabinet 14

Duplex Cabinet and Duplex Unit 15

Duplexing Document Feeder 16

Automatic Document Feeder 17

20-Bin Staple Sorter and Sorter 18

10-Bin Staple Sorter and Sorter 19

Data Controller 20

3. Control Panel Keys and Indicators

Basic Panel 22

System Panel 24

Supplementary Panel 26

Display Panel 28

4. Turning On and Off, and Resetting The Copier

Turning On and Off 30

When Copier is Turned On 31

Auto Copy Start Function 32

Energy Saver Mode 33

Initial Mode and Panel Resetting 34

Auto Reset Function 35

Entering the Access Number 36

Contents

iii

Chapter 3 Making Copies 37

1. Basic Copying Overview 38

2. Basic Copying Procedure

Original Placement 40

Using Automatic/Duplexing Document Feeder 42

Image Density 48

Zoom Ratio

• Types of Zoom Ratio 50

• Auto Size Mode 56

• Zoom Ratio Table (Orignal Size to Paper Size) 58

Paper Size

• Manual Mode 60

• Auto Paper Mode 62

• Special Paper Mode 64

Number of Copies 66

Copy Cycle Start 67

Interrupt Mode 68

Multi Bypass Copying 70

3. System Copying Overview 72

4. System Copying Procedure

Original Copy Type

• Type I 74

• Type II 76

• Original Count Mode 82

Finishing Mode

• Finishing Modes 86

• Auto Dual Function 88

• Selecting the Finishing Mode 90

• Typical Finishing Mode 94

5. Supplementary Copying Overview 96

6. Supplementary Function Setting

Erase 98

File Margin 102

Book 106

Cover 108

Insertion 114

Job Memory 124

▼

Contents

iv

Chapter 4 Special Functions 127

1. Meter Count Function 128

2. Auxiliary Toner Replenishing Mode

(Increasing the Image Density) 130

3. Drum Dehumidify Function 131

4. User’s Choice 132

Chapter 5 When a Warning Message

Appears 143

1. Quick Reference for Warning Messages and

Indicator Lights 144

2. Detailed Instructions for Messages/Indicator Lights

Add Toner Indicator 146

Add Paper Indicator 148

Add Staples Indicator 154

Closure Failure Indicator 162

Misfeed Indicator

• Misfeed Indicator and Monitor Display 166

• Misfeed Clearing Procedure

•

Copier 168

•

Paper Feed Cabinet 172

•

Duplex Unit 176

•

Duplexing Document Feeder 178

•

Automatic Document Feeder 179

•

Sorter/Staple Sorter 180

Call-Technical-Representative Indicator 182

Contents

v

Chapter 6 Troubleshooting 183

1. When This Type of Copy is Produced

•

The Image is too Light 184

•

The Image is too Dark 184

•

The Image is too Blurry 184

•

The Copy has Lines 186

•

The Copy has dark specks or spots 186

•

The Edge of the Copy is dirty 186

•

The Image on the Copy is not aligned properly 186

2. The Copier is not Activated

•

No Indicators on the Control Panel light up 188

•

The Message Display shows nothing 188

•

Pressing The Start Key does not start the copy cycle 188

•

Control panel keys do not start the copy cycle 188

•

The Copier is not activated when the Power Switch is turned

ON 188

Chapter 7 Specifications 191

1. Copier 192

2. Paper Feed Cabinet 194

3. Duplexing Document Feeder 196

4. Automatic Document Feeder 197

5. 20 Bin Staple Sorter 198

6. 10 Bin Staple Sorter 199

7. 20 Bin Sorter 200

8. 10 Bin Sorter 201

9. Duplex Unit 202

10. Data Controller 203

11. Copier Outline Dimensions 204

Contents

vi

Contents

Chapter 8 Miscellaneous 205

1. Care of the Copier

•

Daily Checks 206

•

Cleaning 208

2. Function Combination Matrix 212

3. Description of Paper Size 216

4. Zoom Ratio Table

(Original Size to Paper Size) 217

5. Index 218

Chapter 1

Safety Notes

Chapter 2

First Things to

Know about

EP2050

Chapter 3

Making Copies

Chapter 4

Special Functions

Chapter 5

When a Warning

Message Appears

Chapter 6

Troubleshooting

Chapter 7

Specifications

Chapter 8

Miscellaneous

vii

Organization

This manual consists of eight chapters.

Chapters 1 through 3 give the basic information for making copies. Be sure to

read these Chapters before using your copier.

Chapter 1 Safety Notes

About the operating environment, conditions and precautions for use.

Chapter 2 First Things to Know About EP2050

A brief description of the system and preliminary information about

the different parts of the system.

Chapter 3 Making Copies

About how to make basic, system and supplementary copies.

Basic Copying Overview is p. 38

System Copying Overview is p. 72

Supplementary Copying Overview is p. 96

These pages offer quick, at-a-glance flowcharts for making copies.

Each step is keyed to a page number where you will find more

detailed information.

Chapter 4 Special Functions

About the special functions that can be used for specific purposes.

Chapter 5 When a Warning Message Appears

About the various warning indications given on the Message Display

and Display Panel and steps to correct these conditions.

Chapter 6 Troubleshooting

Instructions on how to troubleshoot copier malfunctions.

Chapter 7 Specifications

Complete specifications of the copier system and options.

Chapter 8 Miscellaneous

About care of the copier and possible combinations of functions.

Using This Manual

viii

Page Organization

Each page of this manual is basically organized as follows.

Control Panel Indicators

A steady light or blinking light indicator on the control panel is indicated as

follows.

1139O4760A

➭

p. XX (Cross-reference):

Shows the page to refer to for more detailed information.

Index: To locate your Chapter quickly.

Section title

Table of contents of the Chapter:

To quickly locate your page in the Chapter.

1076O298

1139O4770A

Using This Manual

ix

Feeding Direction (copy paper path)

In this copier system, copy paper is taken up from the right-hand side of the

copier and fed through the copier toward the left-hand side, out face up onto the

Exit Tray. In the figure below, the direction in which the copy paper is fed, as

indicated by the arrow, is called the "feeding direction."

Terms and Symbols for the Type of Originals and Copy

Paper

A few special terms and symbols are used in this manual to designate types of

originals and copy paper. These two pages explain about these terms and

symbols.

1139O1702A

Using This Manual

x

"Width" and "Length"

1139O1610A

When we talk about the size of the

original or copy, we call side A

"width" and side B "length."

A: Width

B: Length

Terms and Symbols Used

1139O1610A

When the original or copy has a

"length" longer than its "width," we

call it "lengthwise" and use symbol

"L" or " ."

1139O1620A

When the original or copy has a

"length" shorter than its "width," we

call it "crosswise" and use symbol

"C" or " ."

Using This Manual

xi

xii

Chapter 1

Safety Notes

This Chapter explains about the operating environment, conditions,

and precautions for use.

1. Installing the Copier

Installation Site 2

Power Source 2

Grounding 2

Space Requirements 3

2. Precautions for Use

Operating Environment 4

Using the Copier Properly 4

Care of Copier Supplies 4

Moving 5

Chapter 1

Safety Notes

1

Installation Site

To ensure utmost safety and prevent possible malfunctions of the copier, install it

in a location which meets the following requirements.

◆

A place away from a curtain or the like that may catch fire and burn easily.

◆

An area where there is no possibility of being splashed with water or other

types of liquid.

◆

An area free from direct sunlight.

◆

A place out of the direct air stream of an air conditioner, heater, or ventilator.

◆

A well-ventilated place.

◆

A dry place.

◆

A dust-free location.

◆

An area not subject to undue vibration.

◆

A stable and level location.

Power Source

The power source voltage requirements are as follows.

◆

Use a power source with little voltage fluctuation.

◆

If any other electrical equipment is sourced from the same power outlet, make

sure that the capacity of the outlet is not exceeded.

◆

The outlet should be located near the copier and easily accessible.

◆

Never connect any other appliances or machines by means of a multiple socket

to the outlet being used for the copier.

◆

If an extension cord is needed, use one with a capacity more than the power

consumption of the copier.

◆

Make sure that no unusual, excessive force is being applied to the power cord

or extension cord.

Grounding

To prevent receiving electrical shocks in the case of electrical leakage, always

ground the copier.

Connect the grounding wire to:

◆

The ground terminal of the outlet.

◆

A grounding contact which complies with the local electrical standards.

Voltage Fluctuation : Within ±10%

Frequency Fluctuation : 50 Hz Within ±2.5%

: 60 Hz Within ±3%

1. Installing the Copier

Never connect the grounding wire to a gas pipe, a grounding wire for a

telephone or a water pipe.

NOTE

Safety Notes

Chapter 1

2

Space Requirements

To ensure easy copier operation, supply replacements and service maintenance,

adhere to the recommended space requirements detailed below.

1136O163AA

1139O163AA

1,350

150

<Scale: mm>

1136O162AA

2,165

300

200

1. Installing the Copier

Be sure to allow a clearance of 150 mm or more at the back of the copier as

there is a ventilation duct.

NOTE

Chapter 1

Safety Notes

3

= Locate the Copier in a Well Ventilated Room =

A negligible amount of ozone is generated during normal operation of this

copier. An unpleasant odor may, however, be created in poorly ventilated

rooms during extensive copier operations. For a comfortable, healthy, and

safe operating environment, it is recommended that the room be well

ventilated.

NOTE

Operating Environment

The operating environmental requirements of the copier are as follows.

Temperature : 10°C to 30°C (50°F to 86°F) with a fluctuation of 10°C (50°F) per hour

Humidity : 15% to 85% with a fluctuation of 20% per hour

Using the Copier Properly

To ensure the optimum performance of the copier, follow the precautions listed

below.

◆

NEVER place a heavy object on the copier or subject the copier to shocks.

◆

NEVER open any Doors, or turn OFF the copier while the copier is making

copies.

◆

NEVER bring any magnetized object or use flammable sprays near the copier.

◆

NEVER place a vase or vessel containing water on the copier.

◆

NEVER drop paper clips, staples, or other small pieces of metal into the copier.

◆

NEVER attempt to remove any Cover that is secured.

◆

ALWAYS insert the Power Plug all the way into the outlet.

◆

ALWAYS make sure that the outlet is visible, clear of the copier or copier

cabinet.

◆

ALWAYS ensure that the copier does not ride on the power cord or

communications cable of other electrical equipment, and it does not get such a

cord or cable wedged into its own mechanism.

◆

NEVER leave a damaged or cracked copier power cord unattended. If you find

any of these conditions, immediately shut down the copier, unplug the power

cord, and call your Technical Representative for appropriate action.

◆

ALWAYS provide good ventilation when making a large number of continuous

copies.

◆

NEVER leave the copier running when it becomes inordinately hot or produces

abnormal noise. If that happens, immediately turn OFF the copier, unplug it,

and then call your Technical Representative.

2. Precautions for Use

Safety Notes

Chapter 1

4

Care of Copier Supplies

Use the following precautions when handling the copier supplies (toner, paper,

etc.).

◆

Store paper, toner, and other supplies in a place free from direct sunlight and

away from any heating apparatus. Keep them in a dry, clean environment.

◆

Store paper, which has been removed from its wrapper but not loaded into the

Drawer, in a sealed plastic bag in a cool, dark place.

◆

Keep supplies out of the reach of children.

◆

If your hands become soiled with toner, wash them with soap and water

immediately.

Moving

If you need to transport the copier over a long distance, consult your Technical

Representative.

1. Precautions for Use

Chapter 1

Safety Notes

5

6

Chapter 2

First Things to Know

about EP2050

This Chapter gives you a brief description of the system and

preliminary information about the different parts of the system.

1. System Overview 8

2. Copier Parts and Accessories

Outside Your Copier 10

Inside Your Copier 12

Paper Feed Cabinet 14

Duplex Cabinet and Duplex Unit 15

Duplexing Document Feeder 16

Automatic Document Feeder 17

20-Bin Staple Sorter and Sorter 18

10-Bin Staple Sorter and Sorter 19

Data Controller 20

3. Control Panel Keys and Indicators

Basic Panel 22

System Panel 24

Supplementary Panel 26

Display Panel 28

4. Turning ON and OFF, and Resetting The Copier

Turning ON and OFF 30

When Copier is Turned ON 31

Auto Copy Start Function 32

Energy Saver Mode 33

Initial Mode and Panel Resetting 34

Auto Reset Function 35

Entering the Access Number 36

Chapter 2

First Things to Know about EP2050

7

The EP2050 system can be configured with the following

components.

◆

Automatic Document Feeder AF-3 <Option>

Permits automatic feeding of multiple

originals.

➭

p. 42

1139O0010A

◆

Staple Sorters <Option>

Staple Sorter ST-101

Automatically staples the copy sets or stacks

that are sorted or grouped the same as with the

S-104.

➭

p. 90

Staple Sorter ST-206

Automatically punches holes in the copy sets or

stacks that are sorted or grouped, in addition to

the functions provided by the ST-101.

1136O059AA

1139O1222A

◆

Duplex Unit AD-5 <Option>

Mounted in the 3rd Drawer of the

Paper Feed Cabinet, it turns over

1-sided copies to make 2-sided

copies.

➭

p. 80

◆

Duplex Cabinet PF-2D <Option>

Turns over 1-sided copies to make

2-sided copies. It is also equipped

with a storage drawer for keeping

copy paper and toner.

➭

p. 74

◆

Sorters <Option>

10-Bin Sorter S-104/20-Bin Sorter S-205

Permits sorting or grouping copies into up to

10 or 20 copy sets or stacks.

➭

p. 90

1139O0020A

1. System Overview

Chapter 2

First Things to Know about EP2050

8

Page is loading ...

Konica Minolta EP2050 User manual

Konica Minolta EP2050 User manual

Related papers

Other documents