Husqvarna 265 ACX User manual

HUSQVARNA AUTOMOWER

®

265 ACX

OPERATOR’S MANUAL

TABLE OF CONTENTS

English - 3

1. Introduction and safety

..............................................................

5

1.1 Introduction

.....................................................................................

5

1.2 Symbols on Automower

®

...........................................................

6

1.3 Symbols in the Operator’s Manual

..........................................

7

1.4 Safety instructions

........................................................................

8

2. Presentation

..................................................................................

10

2.1 Automower

®

, what’s what?

.....................................................

11

2.2 Function of Automower

®

...........................................................

12

2.3 Search method

............................................................................

15

2.4 More than one Automower

®

in a garden

.............................

16

2.5 One Automower

®

in several gardens

...................................

16

2.6 GPS communication unit

..........................................................

16

3. Installation

.....................................................................................

17

3.1 Preparations

.................................................................................

17

3.2 Installation of the charging station

.......................................

18

3.3 Charging the battery

..................................................................

22

3.4 Installation of the boundary wire

...........................................

23

3.5 Connecting the boundary wire

..............................................

30

3.6 Checking the installation

.........................................................

32

3.7 Linking Automower

®

to the charging station

.....................

32

3.8 Installation of the guide wire

..................................................

33

3.9 Activate the GPS anti-theft protection area

........................

37

4. Use

....................................................................................................

38

4.1 Charging a discharged battery

...............................................

38

4.2 Using the timer

............................................................................

39

4.3 Using GPS-communication

....................................................

39

4.4 Starting Automower

®

..................................................................

41

4.5 Stopping Automower

®

...............................................................

42

4.6 Restart

............................................................................................

42

4.7 Switching off Automower

®

........................................................

42

4.8 Adjusting the cutting height

.....................................................

43

5. Control panel

................................................................................

44

5.1 Shortcuts

.......................................................................................

45

5.2 Numbers

........................................................................................

46

5.3 Main switch

...................................................................................

46

6. Menu functions

............................................................................

47

6.1 Main menu

....................................................................................

47

6.2 Automower

®

main menu, menu overview

...........................

48

6.3 Commands (1)

.............................................................................

49

6.4 Timer (2)

........................................................................................

49

6.5 Installation (3)

..............................................................................

51

6.6 Settings (4)

...................................................................................

57

7. Garden example

..........................................................................

61

8. Maintenance

..................................................................................

65

8.1 Battery

............................................................................................

65

8.2 Winter storage

.............................................................................

66

8.3 Service

...........................................................................................

66

8.4 After winter storage

....................................................................

67

8.5 Cleaning

........................................................................................

67

8.6 Replacing the blades

................................................................

68

8.7 Transport and moving

...............................................................

68

9. Trouble shooting

........................................................................

69

9.1 Fault messages

...........................................................................

69

9.2 Fault symptom

.............................................................................

72

10. Technical data

...........................................................................

73

11. Environmental information

..................................................

74

12. EU declaration of conformity

..............................................

75

TABLE OF CONTENTS

4 - English

English - 5

1. INTRODUCTION AND SAFETY

1. Introduction and safety

1.1 Introduction

Congratulations on your choice of an exceptionally

high quality product. To get the best results from your

Husqvarna Automower

®

requires knowledge of its

function. This Operator's manual contains important

information about the mower, how you install it and

how you use it.

The following system is used in the Operator's manual

to make this easier:

•

Italic

content

indicates one of the following:

• It is shown in the mower's display

• It is an SMS via a mobile phone

• It is a reference to a another section in the

operator's manual.

• Words written in

bold

are one of the buttons on

the mower's keypad.

• Words written in

UPPERCASE

and

italics

refer to

the position of the main switch and the different

operating modes on the mower.

Husqvarna AB has a policy of continuous product

development and therefore reserves the right to modify

the design and appearance and function of products

without prior notice.

IMPORTANT INFORMATION

Read through the Operator’s Manual carefully

and understand the content before using

your Automower

®

.

WARNING

Automower

®

can be dangerous if

incorrectly used.

6 - English

1. INTRODUCTION AND SAFETY

1.2 Symbols on Automower

®

These symbols can be found on the lawn mover. Study

them carefully so you understand their significance.

• Read through the Operator’s Manual carefully

and understand the content before using your

Automower

®

.

• The warnings and safety instructions in this

Operator’s Manual must be carefully followed if

the mower is to be used safely and efficiently.

• Automower

®

can only start when the main switch

is moved to the

ON

position and the correct PIN

code has been entered. Inspection and/or

maintenance must be carried out with the main

switch set to

OFF

.

• Keep your hands and feet away from the rotating

blades. Never place your hands or feet close to

or under the body when Automower

®

is in

operation.

• Do not ride on Automower

®

.

• Noise emission to surroundings. The machine's

emission is specified in chapter Technical data

and on label.

• This product conforms to the applicable

EU Directives.

• This product contains components tested

according to FCC (complete system not tested).

• It is not permitted to dispose of this product as

normal household waste when it has reached the

end of its useful life. Ensure that the product is

recycled in accordance with local legal

requirements.

English - 7

1. INTRODUCTION AND SAFETY

1.3 Symbols in the Operator’s Manual

These symbols can be found in the Operator’s Manual.

Study them carefully so you understand their

significance.

• Inspection and/or maintenance must be carried

out with the main switch set to

OFF

.

• Always wear protective gloves when working

with the mower’s underframe.

• Never use a high-pressure washer or even

running water to clean Automower

®

.

• A warning box indicates a risk of personal injury

exist, especially when the stated instructions are

not followed.

• An information box indicates a risk of material

damage exist, especially when the stated

instructions are not followed. The box is also

used where there is a risk of user error.

OFF

WARNING

Xxxxxx xxxxx xxxx xxxx xxxxx xxx.

IMPORTANT INFORMATION

Xxxxxx xxxxx xxxx xxxx xxxxx xxx.

8 - English

1. INTRODUCTION AND SAFETY

1.4 Safety instructions

Use

• This robotic lawn mower is designed to mow

grass in open and level ground areas. It may only

be used with the equipment recommended by

the manufacturer. All other types of use are

incorrect. The manufacturer’s instructions with

regard to operation, maintenance and repair

must be followed precisely.

• The robotic lawn mower may only be operated,

maintained, and repaired by persons that are fully

conversant with its special characteristics and

safety regulations. Please read the Operator’s

Manual carefully and make sure you understand

the instructions before using the robotic lawn

mower.

• It is not permitted to modify the original design of

Automower

®

. All modifications are made at your

own risk.

• Check that there are no stones, branches, tools,

toys or other objects on the lawn that can

damage the blades and cause the mower to

stop.

• Start Automower

®

according to the instructions.

When the main switch is in the

ON

position;

make sure you keep your hands and feet away

from the rotating blades. Never put your hands

and feet under the mower.

• Never lift up Automower

®

or carry it around when

the main switch is in the

ON

position.

• Do not let persons who do not know how

Automower

®

works and behaves use the mower.

• Never use Automower

®

if persons, especially

children, or pets, are in the immediate vicinity.

• Do not put anything on top of Automower

®

or its

charging station.

• Do not allow Automower

®

to be used with a

defective blade disc or body. Neither should it be

used with defective blades, screws, nuts or cables.

• Do not use Automower

®

if the main switch does

not work.

• Always switch off Automower

®

using the main

switch when you do not intend to use the mower.

Automower

®

can only start when the main switch

is moved to the

ON

position and the correct PIN

code has been entered.

• Automower

®

must never be used at the same time

as a sprinkler. In this case use the timer function,

see

6.4 Timer (2)

on page 49, so the mower and

sprinkler never run simultaneously.

English - 9

1. INTRODUCTION AND SAFETY

Transport

The original packaging should be used when

transporting Automower

®

over long distances.

To safely move from or within the working area:

1. Press the

STOP

button to stop the mower.

If the anti-theft alarm (see page 59) is activated;

enter the first digit of the PIN code.

You select the four digit PIN code when you start

the mower for the first time, see page 32.

2. Move the main switch to the

OFF

position if you

intend to carry the mower.

3. Carry the mower by the handle at the rear under

the mower. Carry the mower with the blade disc

away from the body.

Maintenance

• Inspect Automower

®

each week and replace any

damaged or worn parts.

Check especially that the blades and blade disc

are not damaged. Replace all blades and screws

at the same time if necessary so that the rotating

parts are balanced, see

8. Maintenance

on

page 65.

WARNING

When the mower is turned upside

down the main switch must always

be set to the

OFF

position.

The main switch should be set to the

OFF

position during all work on the

mower’s underframe, such as

cleaning or replacing the blades.

ON

OFF

10 - English

2. PRESENTATION

2. Presentation

This chapter contains information you should be aware

of when planning the installation.

An installation of Husqvarna Automower

®

includes four

main components:

Automower

®

, an automatic lawn mower that mows

the lawn by moving in essentially an irregular pattern.

The mower is powered by a maintenance-free

battery.

Charging station, where your Automower

®

returns

when the charge level in the battery becomes too low.

The charging station has three functions:

• To send control signals along the boundary wire.

• To send out signals so Automower

®

finds the

charging station.

• To charge Automower

®

battery.

Transformer, which is connected between the

charging station and a 230V wall socket. The

transformer is connected to the wall socket via an

integrated power cord and to the charging station via

a 20 m long low voltage cable. The low voltage cable

must not be extended. The low voltage cable must

not be shortened nor extended.

Wire, laid in a loop around Automower

®

’s working

area. The boundary wire is laid around the edges of

the lawn and around objects and plants that the

mower must not run into. The wire is also used for

any guide wires. Contact your dealer to purchase a

cable with the right length.

English - 11

2. PRESENTATION

2.1 Automower

®

, what’s what?

The numbers in the picture correspond to:

1. Charging strip

2. Cutting height adjustment cover

3. Catch button to open the cutting height adjustment

cover

4. Ultrasonic sensors

5. Drive wheel

6. Body

7. Stop button

8. Keypad

9. Display

10. Main switch

11. Front wheel

12. Handle

13. Chassis box with electronics, battery and motors

14. Skid plate

15. Blade disc

16. Charging station

17. Contact strips

18. LED for operation check of the boundary wire

19. Loop wire for the boundary wire and guide wire

20. Transformer with power cord

21. Low voltage cable

22. Staples

23. Connector for the loop wire

24. Screws for securing the charging station

25. Measurement gauge for help when installing the

boundary wire

26. Solderless coupler for the loop wire

27. Operator’s Manual

8

9

10

12

13

14

15

16

17

20

21

23

26

27

7

1

2

3

4

6

7

25

24

5

18

19

22

11

12 - English

2. PRESENTATION

2.2 Function of Automower

®

Capacity

Automower

®

is recommended for lawns up to 6000 m

2

+/-20%.

How large an area is mown depends primarily on the

condition of the blades and the type of grass, growth

rate and humidity. The shape of the garden is also

significant. If the garden mainly consists of open lawns,

Automower

®

can mow more per hour than if the garden

consists of several small lawns separated by trees,

flower beds and passages.

How long Automower

®

mows and recharges can vary

depending on, among others, the ambient

temperature. Up to around 25 ˚C, a fully charged

Automower

®

will mow for approx. 80 minutes,

depending on the age of the battery and how thick the

grass is. Then the mower will charge for approx. 40

minutes

Above 25 °C both the mowing and charging times

gradually drop.

Mowing technique

The mowing system used by Automower

®

is based on

an effective and energy efficient principle. Unlike

normal lawn mowers, Automower

®

cuts the grass

instead of striking it off.

We recommend you allow Automower

®

to mainly mow

in dry weather to obtain the best possible result.

Automower

®

can even mow in the rain, however, wet

grass easily collects on the mower and the risk of

slipping on steep slopes is greater.

If there is risk for thunder, the transformer should be

disconnected from the power, and the boundary wire

and the guide wire from the charging station.

The blades must be in good condition to obtain the

best mowing result. In order to keep the blades sharp

for as long as possible it is important to keep the lawn

free from branches, small stones and other objects.

Replace the blades regularly for the best mowing

result. It is very easy to replace the blades. See

8.6

Replacing the blades

.

English - 13

2. PRESENTATION

Working method

Automower

®

automatically mows the lawn.

It continuously combines mowing and charging.

The charging station sends out a signal that

Automower

®

can sense at a distance of 6 - 7 metres.

The mower starts to search for the charging station

when the battery charge becomes too low.

Automower

®

does not mow when it is searching for

the charging station.

When Automower

®

searches for the charging station

it uses one or more of three different search methods:

Irregular, Follow boundary wire and Follow guide

wire. For more information about the search

methods, see

2.3 Search method

on page 15 and

Follow loop in (3-2-2)

on page 53.

When the battery is charged the mower reverses,

turns around and leaves the charging station in a

randomly selected direction within the exit sector

90° - 270°.

To make it easier for Automower

®

to reach all parts of

the garden you can manually set how the mower will

leave the charging station, see

6.5 Installation (3)

on

page 51.

Automower

®

is equipped with ultrasonic sensors that

effectively sensor both fixed and moving obstacles

that the mower is subjected to. When faced with an

obstacle, the mower slows down to avoid

unnecessarily hard collisions. When Automower

®

body hits an obstacle, the mower reverses and

selects a new direction.

Two additional sensors, one on the front and one on

the back of the Automower

®

, will sense when the

mower is approaching the boundary wire.

Automower

®

overruns the wire by up to

27 centimetres before it turns. The overrun length

can be set, see

Drive past wire (3-4-2)

on page 57.

The

STOP

button on the top of Automower

®

is mainly

used to stop the mower when it’s running. When the

STOP

button is pressed a cover opens, behind which

there is a control panel. The

STOP

button remains

depressed until the cover is closed again. This acts

as start inhibitor.

14 - English

2. PRESENTATION

The control panel on the top of Automower

®

is where

you manage all the mower settings. The main switch

is also located on the control panel. Open the control

panel cover by pressing down the

STOP

button.

When the main switch is turned

ON

for the first time, a

start-up sequence begins which includes: selection of

the language, time format, date format and four digit

PIN code, plus setting of the time and date, see

page 32.

The selected PIN code must then be entered each

time the main switch is moved to the

ON position.

This theft-prevention function is called Time lock(4-1-2)

and Automower

®

has this function activated as a

default setting. The function also means that the

mower stops mowing after a set number of days and

will not continue until the correct PIN code has been

entered. The function can be deactivated or changed

as required. For more information about Time

lock(4-1-2), see page 58.

Automower

®

can enter a sleep mode to save power.

The display on the control panel is then completely

dimmed.

The sleep mode is activated 25 minutes after the

STOP button has been pressed and then not reset to

the operating mode. Automower

®

is then activated by

switching the main switch off and on.

The sleep mode can also be activated in the event of

a fault occurring during mowing or charging and

which is not rectified within 25 minutes. Automower

®

is then activated by pressing the STOP button.

Movement pattern

The mower’s movement pattern is irregular and is

determined by Automower

®

itself. A movement

pattern is never repeated. This mowing system

means the lawn is mown equally without any mowing

lines.

If Automower

®

enters an area where it senses the

grass is longer than earlier, it can change the

movement pattern. It can then mow in a square

pattern to cover the area of longer grass more

systematically.

When Automower

®

mows in a square pattern, this is

known as square mode cutting. The mower must

have been operational for more than 6 hours in order

for Automower

®

to start square mode cutting.

English - 15

2. PRESENTATION

2.3 Search method

Automower

®

can be set to search for the charging

station in three different ways. Using the setting

options the three search methods can be combined to

optimise the search for the charging station. The

required search method or methods depends on the

shape of the garden.

Search method 1: Irregular

Automower

®

runs irregularly until it finds the charging

station.

This search method is best for an installation that has

an open lawn and no narrow passages (narrower

than about 3 metres).

The advantage of this search method is that there is

no risk of leaving tracks in the grass after the mower.

The disadvantage is that the search times can be

somewhat longer.

Search method 2: Follow boundary wire

Automower

®

runs irregularly until it reaches the

boundary wire. The mower then follows the boundary

wire in to the charging station.

This search method is best for an installation that has an

open lawn with wide passages (wider than about

3 metres) and no, or only a small, island.

The advantage of this search method is that the search

times are generally short.

The disadvantage is that tracks can be formed to a

certain extent in the grass behind the mower. Problems

can also arise if there are narrow passages or a large

number of islands, for example, bushes.

Automower

®

circles an island roughly twice, which can take a long time

and create tracks.

Search method 3: Follow guide wire

Automower

®

runs irregularly until it reaches the guide

wire. The mower then follows the guide wire in to the

charging station.

The guide wire is an extra wire that is laid from the

charging station, out towards a remote part of the

working area or through a narrow passage and is then

connected to the boundary wire. Up to two guide wires

can be installed for 265 ACX. For more information, see

3.8 Installation of the guide wire on page 33.

This search method is best for an installation that has

numerous or large islands, narrow passages or steep

slopes.

The advantage of this search method is that the search

times are generally short.

The disadvantage is that the mower can leave tracks in

the grass along the length of the guide wire.

16 - English

2. PRESENTATION

2.4 More than one Automower

®

in

a garden

If you install more than one Automower

®

in the same

area of lawn, each mower must have its own PIN code.

A complete installation, including charging station, is

required for each mower. The boundary wires for the

different installations can be routed next to each other.

Contact your dealer for further information.

2.5 One Automower

®

in several

gardens

One Automower

®

can easily be used for more than one

garden, where each garden has its own charging

station and boundary wire. The mower can then have

the same PIN code for all gardens.

Contact your dealer for further information.

2.6 GPS communication unit

Automower

®

GPS communication unit contains two

main functions;

1. The SMS feature allows you to communicate with

the Automower

®

via SMS. In this way, one can

alter settings as well as start and stop the mower

remotely and as required. The mower sends an

SMS if it should stop working.

2. GPS anti-theft protection offers increased

protection and control of the Automower

®

. If the

mower is moved outside the preset protection

area, an SMS alert message is sent. New SMS

are sent with updated location details as the

Automower

®

is moved. The movement can be

followed using an online map service by entering

the positioning data provided in the SMS.

English - 17

3. INSTALLATION

3. Installation

This chapter describes how you install Husqvarna

Automower

®

. Before starting the installation read the

previous chapter 2. Presentation.

Read the whole of this chapter too before starting the

installation. How the installation is made also affects

how well Automower

®

will work. It is therefore

important to plan the installation carefully.

Planning is simplified if you make a sketch of the

working area, including all obstacles. This makes it

easier to see the ideal positions for the charging

station, boundary wire and guide wire, if used. Draw on

the sketch how the boundary wire and the guide wire, if

used, should be routed.

Carry out the installation in the following steps:

3.1 Preparations.

3.2 Installation of the charging station.

3.3 Charging the battery.

3.4 Installation of the boundary wire.

3.5 Connecting the boundary wire.

3.6 Checking the installation.

3.7 Linking Automower® to the charging station.

3.8 Installation of the guide wire.

To carry out a complete start-up of Automower

®

the

charging station must be in position and connected,

the boundary wire connected, and the mower

connected to the charging station. If you would like to

start the mower without having completed the full

boundary installation, you can connect a temporary

short loop around the mower.

3.1 Preparations

1. If the lawn in the proposed working area is taller

than 10 cm, mow it using a normal lawn mower.

Then collect the clippings.

2. Read carefully through all the steps before the

installation.

3. Check that all parts for the installation are

included:

The numbers in brackets refer to the detail

diagram 2.1 Automower®, what’s what? on

page 11.

• Operator’s Manual (27)

• Automower

®

• Charging station (16)

• Transformer (20)

• Low voltage cable (21)

18 - English

3. INSTALLATION

• Screws for the charging station (24)

• Measurement gauge (25)

• Connector for the loop wire (23)

• Solderless coupler for the loop wire (26)

Contact your dealer to purchase the following

installation material:

• Loop wire for the boundary wire and guide wire

(19)

• Staples (22)

During installation you will also need:

• Hammer/plastic mallet to simplify putting the

staples in the ground

• Combination pliers for cutting the boundary

wire and pressing the contact units together.

• Edge cutter/straight spade if the boundary wire

must be buried.

3.2 Installation of the charging

station

Best charging station location

Take the following aspects into consideration when

identifying the best location for the charging station:

• Allow for 3 metres of free space in front of the

charging station

• Close to a wall socket. The supplied low voltage

cable is 20 metres long.

• A level surface to place the charging station on.

• Protection from water spray for instance from

irrigation

• Protection from direct sunlight

• Place in the lower part of a working area that has

a major slope

• Possible requirement to keep the charging

station out of sight for outsiders

• Any aesthetic preferences

For examples of where best to install the charging

station, see 7. Garden example on page 61.

If you are going to install a guide wire, read 3.8

Installation of the guide wire, see page 33, before

choosing the position of the charging station.

English - 19

3. INSTALLATION

The charging station must be positioned with a great

deal of free area in front of it (at least 3 metres). It

should also be positioned centrally in the working

area so that Automower

®

can easily find the charging

station and quickly reach all parts of the working

area.

It is a good idea to place the charging station in the

shadow. The battery is spared if it is charged in the

lowest possible ambient temperature.

The charging station must be positioned on relatively

level ground. The height difference must not differ

more than 5 cm between the front and rear of the

charging station.

The charging station must not be positioned so that

its plate bends.

Consider the distance to a wall socket when choosing

the position. The charging station should be

connected to a 230V wall socket via the low voltage

cable and transformer. The supplied low voltage

cable is 20 metres long.

Tip! It is possible to let the low voltage cable cross

the working area. It must then be either stapled down

or buried. In some cases there is a better positioning

option for the charging station than close to a house

wall or by the closest wall socket.

The transformer must be placed where it is well

ventilated and is not exposed to direct sunlight. It is

also beneficial if the transformer can be placed under a

roof.

It is recommended to use an earth fault-breaker when

connecting the transformer to the wall socket.

IMPORTANT INFORMATION

The low voltage cable must not under any

circumstances be shortened or extended.

IMPORTANT INFORMATION

The mains cable on the transformer must not

be replaced. In those cases the mains cable

has been damaged, the transformer must be

discarded and replaced by a new one.

20 - English

3. INSTALLATION

The transformer shall be mounted on a vertical

surface, for example a house wall. Mount the

transformer with screws in the two attachment points.

Securing screws are not included. Choose screws

suitable for the wall material.

Mount the transformer at a height such that there is

no risk the transformer can become submerged in

water (minimum 30 cm from the ground). The

transformer must never be placed on the ground.

Do not put the charging station in a corner or pocket

in the working area.

Avoid placing the charging station in a narrow

passage (narrower than about 3 metres).

Do not position the charging station so that the mower

can come closer than 3 metres behind the charging

station (for example on a narrow point). The mower

will not then find the charging station.

min 30cm/12”

Page is loading ...

Husqvarna 265 ACX User manual

This manual is also suitable for

Husqvarna 265 ACX User manual

Related papers

Other documents