Continental CDIZC - N User manual

Brand: Continental

Model: CDIZC - N

Category: Fireplaces

Type: User manual

This manual is also suitable for

CDIZC - P

W415-0224 / D / 01.15.04

INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER.

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON L4M 4Y8 Canada • (705)721-1212 • fax(705)722-6031

www.continentalfireplaces.com • [email protected]

GAS-FIRED DIRECT VENT INSERT

INSTALLATION AND OPERATION INSTRUCTIONS FOR:

VENTED GAS FIREPLACE HEATER

NATURAL GAS MODELS

CDIZC - N

PROPANE GAS MODELS CDIZC - P

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS

R-2000

• Immediately call your gas supplier

from a neighbour's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier,

call the fire department.

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or death.

FOR YOUR SAFETY

Do not store or use gasoline or other flammable vapours and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

Installation and service must be performed by a qualified installer, service

agency or the gas supplier.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / CSA METHODS

W415-0224 / D / 01.15.04

Pg 2-4 INTRODUCTION

Warranty

General Instructions

General Information

Care of Glass & Plated Parts

5-7 INSTALLATION

Insert Vent Connection

Chimney Connection

Wall Switch / Thermostat

Gas Pipe Installation

7-8 FINISHING

Trim Extrusion Installation

Log Placement

Door Installation

Mantle Clearances

Logo Placement

Pg 9 OPERATION / MAINTENANCE

Operating Instructions

Maintenance

10 REPLACEMENT BLOWER

11 ADJUSTMENTS

Pilot Burner Adjustment

Vent Restrictions

Venturi Adjustments

12-13 REPLACEMENTS

Ordering Replacement Parts

Replacement Parts

Terminal Kits

Accessories

14-15 TROUBLE SHOOTING GUIDE

16 SERVICE HISTORY

NOTE: changes, other than editorial, are denoted by a vertical line in the margin.

WARNING

• The fireplace insert is a vented gas-fired heater. Do not burn wood or other materials in this fireplace insert.

• Adults and especially children should be alerted to the hazards of high surface temperatures and should stay

away to avoid burns or clothing ignition. Supervise young children when they are in the same room as the

fireplace insert.

• Due to high temperatures, the fireplace insert should be located out of traffic and away from furniture and

draperies.

• Clothing or other flammable material should not be placed on or near the fireplace insert.

• Any safety screen or guard removed for servicing must be replaced prior to operating the fireplace insert.

• It is imperative that the control compartments, burners and circulating blower and its passageway in the

fireplace insert and venting system are kept clean. The fireplace insert and its venting system should be

inspected before use and at least annually by a qualified service person. More frequent cleaning may be

required due to excessive lint from carpeting, bedding material, etc. The fireplace insert area must be kept

clear and free from combustible materials, gasoline and other flammable vapours and liquids.

• Under no circumstances should this fireplace insert be modified.

• This fireplace insert must not be connected to a chimney flue pipe serving a separate solid fuel burning

appliance.

• Do not use this fireplace insert if any part has been under water. Immediately call a qualified service technician

to inspect the fireplace insert and to replace any part of the control system and any gas control which has

been under water.

• Do not operate the fireplace insert with the glass door opened, cracked or broken. Replacement of the glass

should be done by a licensed or qualified service person.

• Do not strike or slam shut the fireplace insert glass door.

• This fireplace uses and requires a fast acting thermocouple. Replace only with a fast acting thermocouple

supplied by Wolf Steel Ltd.

TABLE of CONTENTS

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE

W415-0224 / D / 01.15.04

CONTINENTAL gas fireplaces are manufactured under the strict Standard of the world recognized

ISO 9001 : 2000 Quality Assurance Certificate.

CONTINENTAL products are designed with superior components and materials, assembled by trained craftsmen

who take great pride in their work. The burner and valve assembly are leak and test-fired at a quality test station.

Once assembled the complete fireplace is thoroughly inspected by a qualified technician before packaging to ensure

that you, the customer, receives the quality product that you expect from WOLF STEEL Ltd..

CONTINENTAL GAS FIREPLACE PRESIDENT'S LIFETIME LIMITED WARRANTY

The following materials and workmanship in your new The following materials and workmanship in your new

The following materials and workmanship in your new

CONTINENTALCONTINENTAL

CONTINENTAL

gas fireplace are gas fireplace are

gas fireplace are

warranted against defects for as long as you own the fireplace. This covers: combustion cham-warranted against defects for as long as you own the fireplace. This covers: combustion cham-

warranted against defects for as long as you own the fireplace. This covers: combustion cham-

ber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermalber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal

ber, heat exchanger, stainless steel burner, phazer™ logs and embers, ceramic glass (thermal

breakage only), gold plated parts against tarnishing, porcelainized enamelled components andbreakage only), gold plated parts against tarnishing, porcelainized enamelled components and

breakage only), gold plated parts against tarnishing, porcelainized enamelled components and

aluminium extrusion trims.aluminium extrusion trims.

aluminium extrusion trims.

Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,

Electrical (110V and millivolt) components and wearable parts such as blowers, gas valves,

thermal switch, switches, wiring, remote controls, igniter, gasketing, and pilot assembly arethermal switch, switches, wiring, remote controls, igniter, gasketing, and pilot assembly are

thermal switch, switches, wiring, remote controls, igniter, gasketing, and pilot assembly are

covered and covered and

covered and

WOLF STEEL WOLF STEEL

WOLF STEEL

LTD. LTD.

LTD.

will provide replacement parts free of charge during the firstwill provide replacement parts free of charge during the first

will provide replacement parts free of charge during the first

year of the limited warranty.year of the limited warranty.

year of the limited warranty.

Any labour related to warranty repair is not covered.Any labour related to warranty repair is not covered.

Any labour related to warranty repair is not covered.

CONDITIONS AND LIMITATIONS

WOLF STEEL LTD. warrants its products against manufacturing defects to the original purchaser only -- i.e., the individual or legal entity (registered customer) whose name appears on

the warranty registration card filed with WOLF STEEL Ltd. -- provided that the purchase was made through an authorized CONTINENTAL dealer and is subject to the following conditions

and limitations:

This factory warranty is nontransferable and may not be extended whatsoever by any of our representatives.

The gas fireplace must be installed by a licenced, authorized service technician or contractor. Installation must be done in accordance with the installation instructions included with the

product and all local and national building and fire codes.

This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect and parts installed from other manufacturers will nullify this

warranty.

This limited warranty further does not cover any scratches, dents, corrosion or discolouring caused by excessive heat, abrasive and chemical cleaners nor chipping on porcelain enamel

parts, mechanical breakage of PHAZER™ logs and embers, nor any venting components used in the installation of the fireplace.

WOLF STEEL Ltd. warrants its stainless steel burners against defects in workmanship and material for life, subject to the following conditions: During the first 10 years WOLF STEEL

Ltd. will replace or repair the defective parts at our option free of charge. From 10 years to life, WOLF STEEL LTD. will provide replacement burners at 50% of the current retail price.

In the first year only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship provided that the product has been operated in

accordance with the operation instructions and under normal conditions.

After the first year, with respect to this President's Limited Lifetime Warranty, WOLF STEEL LTD. may, at its discretion, fully discharge all obligations with respect to this warranty by refunding

to the original warranted purchaser the wholesale price of any warranted but defective part(s).

WOLF STEEL Ltd. will not be responsible for installation, labour, or any other costs or expenses related to the reinstallation of a warranted part, and such expenses are not covered by this

warranty.

Notwithstanding any provisions contained in this President's Limited Lifetime Warranty, WOLF STEEL’S responsibility under this warranty is defined as above and it shall not in any event

extend to any incidental, consequential or indirect damages.

This warranty defines the obligations and liability of WOLF STEEL Ltd. with respect to the CONTINENTAL gas fireplace and any other warranties expressed or implied with respect to this

product, its components or accessories are excluded.

WOLF STEEL Ltd. neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product. WOLF STEEL Ltd. will not be responsible

for: over-firing, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees, hills, mountains, inadequate vents or ventilation, excessive venting

configurations, insufficient makeup air, or negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc.

Any damages to fireplace, combustion chamber, heat exchanger, brass trim or other component due to water, weather damage, long periods of dampness, condensation, damaging

chemicals or cleaners will not be the responsibility of WOLF STEEL Ltd.

The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. The warranty registration card

must be returned within fourteen days to register the warranty.

WOLF STEEL Ltd. reserves the right to have its representative inspect any product or part thereof prior to honouring any warranty claim.

ALL SPECIFICATIONS AND DESIGNS ARE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE DUE TO ON-GOING PRODUCT IMPROVEMENTS. CONTINENTAL® IS A REGISTERED

TRADEMARK OF WOLF STEEL LTD. PATENTS U.S. 5.303.693.801 - CAN. 2.073.411, 2.082.915. © WOLF STEEL LTD.

W415-0224 / D / 01.15.04

FOR YOUR SATISFACTION, THIS FIREPLACE INSERT

HAS BEEN TEST-FIRED TO ASSURE ITS OPERATION

AND QUALITY!

Minimum inlet gas supply pressure is 4.5 inches water

column for natural gas and 11 inches water column for

propane. Maximum inlet gas pressure is 7 inches water

column for natural gas and 13 inches water column for

propane. Manifold pressure under flow conditions is 3.5

inches water column for natural gas and 10 inches water

column for propane. When the fireplace is installed at el-

evations above 4,500ft, and in the absence of specific rec-

ommendations from the local authority having jurisdiction,

the certified high altitude input rating shall be reduced at

the rate of 4% for each additional 1,000ft.

Expansion / contraction noises during heating up and cool-

ing down cycles are normal and to be expected.

Maximum input is 24,000 BTU/hr for natural gas and pro-

pane. Maximum output for natural gas and propane is

20,400 BTU/hr at an efficiency of 85% with the fan on. Maxi-

mum A.F.U.E. (annual fuel utilization efficiency) rating is

79 % for natural gas and propane. This fireplace insert is

not approved for closet or recessed installations. It is ap-

proved for bathroom, bedroom and bed-sitting room in-

stallations and is suitable for mobile homes. The natural

gas model is suitable for installation in a mobile home that

is permanently positioned on its site and fuelled with natu-

ral gas.

This insert must be recessed into a vented noncombus-

tible wood-burning fireplace (prefabricated or masonry)

only. The minimum fireplace opening size in which the

heater is to be installed is:

HEIGHT 14½ inches

WIDTH 25 inches

DEPTH 11 inches

The minimum allowable chimney flue size is 6" round.

The minimum distance, from the bottom of a combustible

mantle projecting 3" maximum from the wall to the top of

the aluminium trim, is 3".

Do not use abrasive cleaners to clean these parts. Buff

lightly with a clean dry cloth.

The glass is 3/16" ceramic glass available from your

Continental / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE

MATERIALS. Clean the glass after the first 10 hours of op-

eration with a recommended gas fireplace glass cleaner.

Thereafter clean as required. DO NOT CLEAN GLASS

WHEN HOT! If the glass is not kept clean permanent

discolouration and / or blemishes may result.

THIS GAS FIREPLACE INSERT SHOULD BE INSTALLED

AND SERVICED BY A QUALIFIED INSTALLER to con-

form with local codes. Installation practices vary from re-

gion to region and it is important to know the specifics that

apply to your area,

for example: in Massachusetts State:

• The fireplace damper must be removed or welded in the open

position prior to installation of a fireplace insert or gas log.

• The appliance off valve must be a “T” handle gas cock.

• The flexible connector must not be longer than 36 inches.

• The appliance is not approved for installation in a bedroom or

bathroom unless the unit is a direct vent sealed combustion

product.

• WARNING: This product must be installed by a licensed plumber

or gas fitter when installed within the commonwealth of

Massachusetts.

In absence of local codes, install to the current CAN1-

B149 Installation Code in Canada or to the National Fuel

Gas Code, ANSI Z223.1, and NFPA 54 in the United

States. Mobile home installation must conform with local

codes. In the absence of local codes, install to the current

standard for gas equipped mobile housing CAN/CSA

Z240 MH Series in Canada or the manufactured home

construction and safety standard, Title 24 CFR, part 3280,

or the Fire Safety Criteria for manufactured home installa-

tions, Sites and Community Standard ANSI/NFPA 501A in

the United States.

Purge all gas lines with the glass door of the fireplace

insert opened. Assure that a continuous gas flow is at

the burner before closing the door.

Under extreme vent configurations, allow several min-

utes (5-15) for the flame to stabilize after ignition.

The fireplace insert and its individual shutoff valve must be

disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in

excess of 1/2 psig (3.5 kPa). The fireplace insert must be

isolated from the gas supply piping system by closing its

individual manual shutoff valve during any pressure test-

ing of the gas supply piping system at test pressures

equal to or less than 1/2 psig (3.5 kPa).

A 1/8 inch NPT plug, accessible for test gauge connection,

must be installed immediately upstream of the gas supply

connection to the fireplace insert.

The fireplace insert must be electrically connected and

grounded in accordance with local codes. In the absence

of local codes, use the current CSA C22.1 CANADIAN

ELECTRICAL CODE in Canada or the ANSI/NFPA 70-1990

NATIONAL ELECTRICAL CODE in the United States. The

blower power cord must be connected into a properly

grounded receptacle. The grounding prong must not be

removed from the cord plug.

GENERAL INSTRUCTIONS

GENERAL INFORMATION

CARE OF GLASS, AND PLATED PARTS

W415-0224 / D / 01.15.04

Provide adequate ventilation air.

Provide adequate accessibility clearance for

servicing and operating the fireplace insert.

Never obstruct the front opening of the fire-

place insert.

Objects placed in front of the fireplace must

be kept a minimum of 48" away from the

front face of the unit.

FIGURES 1a-c

Clean out ashes from the inside of the wood-burning fire-

place. Make sure that the chimney and wood-burning fire-

place are in a clean and sound condition and constructed

of non-combustible materials. If necessary have any re-

pair work done by a qualified person before installing the

insert. Remove the existing fireplace damper or lock into

an open position.

Using screws, attach the fireplace warning tag

(W385-0199) to the inside of the firebox of the fireplace into

which the insert is being installed.

The sheet-metal parts of the fireplace, in which the gas

fireplace insert is to be installed, must not be cut.

If the wood-burning factory-built fireplace has no gas

access hole(s) provided, an access hole of 1½ inch or

less may be drilled through the lower sides or bottom

of the fireplace in a proper workman like manner. This

access hole must be plugged with non-combustible in-

sulation after the gas supply line has been installed.

Ensure that existing chimney cleanouts fit properly.

The refractory, glass doors, screen rails, screen mesh

and log grates may be removed from the fireplace be-

fore installing the gas fireplace insert.

Smoke shelves, shields and baffles may be removed if

attached by mechanical fasteners.

The ventilation openings in the fireplace may be ob-

structed by the backer plates, aluminium trim etc. but

these parts are not to be applied so as to have an air-

tight seal.

WARNING: THIS FIREPLACE HAS BEEN CONVERTED FOR USE WITH A GAS

FIREPLACE INSERT ONLY AND CANNOT BE USED FOR BURNING WOOD OR SOLID

FUELS UNLESS ALL ORIGINAL PARTS HAVE BEEN REPLACED AND THE FIREPLACE

IS RE-APPROVED BY THE AUTHORITY HAVING JURISDICTION.

ATTENTION: CE FOYER A ETE CONVERTI AFIN D'ETRE UTILISE SEULEMENT COMME

FOYER ENCASTRE AU GAZ ET NE PEUT ETRE UTILSE POUR BRULER DU BOIS OU

TOUT AUTRE COMBUSTIBLE SOLIDE, SANS QUE TOUTES LES PIECES ORIGINALES

AIENT ETE REMPLACEES ET QUE LE FOYER SOIT APPROUVE DE NOUVEAU PAR

LES AUTORITES AYANT JURIDICTION.

W385-0199

3 SIDED BACKER PLATE - FRONT VIEW

4 SIDED BACKER PLATE - FRONT VIEW

TOP VIEW

3 & 4 SIDED BACKER PLATES - SIDE VIEWS

INSTALLATION

W415-0224 / D / 01.15.04

Move the insert close to its final position inside the wood-

burning fireplace. This unit is equipped with 6 levelling

screws located as follows: two are on either side of the

circulation blower on the rear panel; four are located front

and back on either side beneath the log support. Level

using four of the levelling screws. See Figure 1a. Levelling

the unit will eliminate rocking or excessive noise when the

fan is in operation. Once the unit is level, move it partially

into place within the fireplace to allow for all connections to

be made. It is not practical to level the insert once the it has

been installed. Determine the required depth prior to in-

stalling the unit and adjust the four levelling screws accord-

ingly.

Chimney installation must conform to both national and

local code requirements. The chimney must be lined with

one 2" or 3" diameter liner for intake and one 3" diameter

liner for exhaust. The minimum and maximum vent lengths

are 10 and 35 feet respectively. Recommended Continental

kits come in 3 lengths: While the liners must be continuous

from the fireplace to the terminal, to achieve the needed

length, they may be coupled, using an aluminium coupler,

provided installation is sealed & secured.

We recommend that exhaust vents that pass through

unheated spaces, such as a garage or attic, be

wrapped in a protective sleeve to minimize condensa-

tion and reverse flow symptoms. See Trouble Shooting

for details.

This unit is approved for use with a 2" liner for air intake

and a 3" liner for exhaust. For best performance,

however, it is recommended to use two 3" liners.

If a 2" liner is used for the intake, it is necessary to

adjust the primary air shutter. See "Air Shutter Settings"

on page 11.

1. OUTSIDE: Slip one

end of a liner a minimum

of 2" over one of the

collars of the terminal. Se-

cure using 3 screws. Then

seal the joint and screw

heads with high tempera-

ture sealant. Repeat with

the other liner.

NOTE: We recommend that the other end of the exhaust

liner be marked to eliminate the exhaust liner being con-

nected to the intake collar at the unit.

FIGURE 3

4. Detach the two screws from the back of the firebox and

remove the panel, as illustrated.

5. Reaching in through the insert, manoeuvre the vent con-

nection assembly through the openings in the firebox top,

taking care not to damage the gasket. In case of a low

ceiling fireplace, the extension should be removed and

reinstalled after the vent connection is secured to the fire-

box. Attach the restrictor plate to the centre stud and se-

cure the assembly using the three studs and ¼-20 hex

nuts.

INSERT VENT CONNECTION

CHIMNEY CONNECTION

FIGURE 4

VENT CONNECTOR

EXTENSION

RESTRICTOR

PLATE

STUDS

FIGURE5a-b

1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST &

2-3" TO 2" REDUCER:

GDI-2320KT VENT KIT 20FT

GDI-2325KT VENT KIT 25FT

GDI-2335KT VENT KIT 35FT

2-3" DOUBLE PLY ALUMINUM LINER-INLET AND EXHAUST:

GDI-320KT VENT KIT 20FT

GDI-325KT VENT KIT 25 FT

GDI-335KT VENT KIT 35 FT

2. Gently stretch the liners to the required lengths and in-

sert into the chimney. Place the terminal onto the top of the

chimney cap and fit the flashing plate to suit. Make weather

tight by sealing with caulking (not supplied) and fasten to

the chimney with screws and plugs (not supplied)

3. INSIDE: Attach and secure the flex liners to the vent

connection assembly using the same procedure as be-

fore, ensuring that the marked exhaust liner is attached

to the exhaust collar.

FIGURE 2

W415-0224 / D / 01.15.04

To adjust the trim: If the mitre is out of alignment, open

each side and loosen the two screws at either side trim

hinge. Slide the trim up or down to adjust and re-tighten

screws. There is also a very slight in/out adjustment that

can be made.

Note: Since the side panels open and close, to access

the controls, a gap is necessary at the mitre joint.

The top trim piece has an adjustable securing bracket

which enables the trim to be secured to the firebox shell.

In order to close off the fireplace opening or if the opening

is larger than the 3- or 4-sided aluminium extrusion trim

kits, it is recommended to reduce the opening using a non-

combustible material such as ceramic tile, marble, etc or

the GIZBP6-3 or GIZBP6-4 backer plate kits. The outside

edge of the backer plate is finished off with gold trim in-

cluded in each kit. A deluxe flashing kit complete with mar-

quis trim may also be used to complete the installation.

These flashing and trim combinations are available in 6

and 9 inch widths as well as many finishes to accent any

room decor. Mounting brackets, GIZBRKT, are required to

install the deluxe flashing. Detailed installation instructions

are included with each kit.

If this unit is being installed into an existing wood burning,

zero clearance fireplace, then be aware of this precaution:

Any circulation air opening may be covered (with non-

combustible material) but not sealed!

The insert can be equipped

with either a 3- or 4-sided

trim kit to finish off the fire-

place opening. Slide the trim

assembly over the keyholes

(2 per side) and drop into

place. If installing the op-

tional 3- or 4-sided backer

plate (GIZBP6-3 or GIZBP6-

4), it must be hung prior to

the trim kit installation us-

ing the same keyholes.

FIGURE 8

FIRE VIEWING DOOR

FIGURE 11

FIGURE 6

For ease of accessibility, an optional remote wall switch

or millivolt thermostat may be installed in a convenient

location. Route 2-strand solid core millivolt wire from

the gas fireplace insert to the wall switch / millivolt ther-

mostat. The recommended maximum lead length de-

pends on the wire size:

WIRE SIZE MAX. LENGTH

14gauge 100 feet

16gauge 60 feet

18gauge 40 feet

Do not connect either the wall switch, thermo-

stat or gas valve to electricity (110 VOLTS).

The insert may now be

pushed into its final posi-

tion inside the wood-burn-

ing fireplace. Secure the in-

sert to the fireplace using

perforated strapping at-

tached to the two securing

holes on either side of the

unit as shown. We recom-

mend that the trim be in-

stalled before the unit is

placed into its final position.

SECURING

HOLES

FIGURE 7

FIGURE 9

VALVE

CONTROL

DOOR

Install suitable supply piping connection to the

" flex

connector supplied (as per local gas codes).

FIGURE 10

LOOSEN

SCREWS

SLIDE TO

ADJUST

WALL SWITCH / THERMOSTAT GAS INSTALLATION

FINISHING

ALUMINIUM EXTRUSION TRIM KIT

INSTALLATION

W415-0224 / D / 01.15.04

Positioning the logs improperly will cause flame im-

pingement and carboning.

PHAZER

logs and glowing embers, exclusive to Continental

Fireplaces, glow when exposed to direct flame and provide

a unique and realistic glowing effect that is different in every

installation. Take the time to carefully position the glowing

embers for a maximum glowing effect. Use only certified

PHAZER

logs available from your Continental / Wolf Steel

Ltd. dealer.

1. Place the rear log (#1) onto the two log supports and

against the air intake pipe.

2. Position logs #2 and #3 against the grate posts and line up

the studs located on the burner with the holes on the bottom

of the logs. Keep slightly back of the front row of ports.

3. Fit the centre log (#4) into place behind log #3 and into

the pocket provided on the back log.

This can vary according to the mantle depth. Use the graph

to help evaluate the clearance needed.

4. Tear the glowing embers into pieces and place along

the front row of ports covering all of the burner area in front

of the logs. Care should be taken to shred the embers into

thin, small irregular pieces as only the exposed edges of

the fibre hairs will glow. The ember material will only glow

when exposed to direct flame; however, care should be

taken to not block the burner ports. Blocked burner ports

can cause an incorrect flame pattern, carbon deposits and

delayed ignition.

Log colours may vary. During the initial use of the fireplace,

the colours will become more uniform as colour pigments

burn in during the heat activated curing process.

FIGURE 17

MANTLE WIDTH

FIGURE 16

LOWER DOOR BRACKET

FIGURE 12

FIGURE 13

FIGURE 14

Place the door into the two lower door brackets, and se-

cure at the top of the unit with two #10-24 machine screws.

FIGURE 15

GLOWING EMBERS

Remove the backing of the logo supplied and place on the

glass viewing door, as indicated.

½”

LOGO

LOG PLACEMENT DOOR INSTALLATION

MANTLE CLEARANCE

LOGO PLACEMENT

FIGURE 18

W415-0224 / D / 01.15.04

The on-off switch is located behind the left side control

door.

Purge all gas lines with the glass door open. Assure

that a continuous gas flow is at the burner before clos-

ing the door. Allow several minutes (5-15) for the flame

to stabilize after ignition.

Do not operate the main burner of the in-

sert with the door removed.

When lit for the first time, the fireplace will emit a slight

odour for a few hours. This is a normal temporary con-

dition caused by the "burn-in" of paints and lubricants

used in the manufacturing process and will not occur

again. Simply open a window to sufficiently ventilate

the room. After extended periods of non-operation such

as following a vacation or a warm weather season, the

fireplace may emit a slight odour for a few hours. This is

caused by dust particles in the heat exchanger burning

off. Open a window to sufficiently ventilate the room.

PURGE THE GAS LINE WITH THE GLASS DOOR OPEN.

7. Turn gas knob counter-clockwise

to pilot.

8. Depress slightly and hold gas knob while lighting the pilot

with the push button ignitor. Keep knob depressed for one

minute, then release. If pilot does not continue to burn, re-

peat steps 3 through 7.

9. With pilot lit, depress and turn gas knob counter-clock-

wise to on.

10. If equipped with flame adjustment valve, push and turn

knob to high.

11. If equipped with remote on-off switch/thermostat, main

burner may not come on when you turn valve to on. Remote

switch must be in the on position to ignite burner.

12. Turn on all electric power to the fireplace.

FLAME ADJUSTMENT

KNOB

ON/OFF KNOB

A. This fireplace is equipped with a pilot which must be lit

by hand. While following these instructions exactly.

B. Before operating smell all around the fireplace area for

gas and next to the floor because some gas is heavier

than air and will settle on the floor.

C. Use only your hand to turn the gas control knob. Never

use tools. If the knob will not turn by hand, do not try to

repair it. Call a qualified service technician. Force or at-

tempted repair may result in a fire or explosion.

D. Do not use this fireplace if any part has been under water.

Immediately call a qualified service technician to inspect

the fireplace and replace any part of the control system

and any gas control which has been under water.

• Turn off all gas to the fireplace.

• Open windows.

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbour's

phone. Follow the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire depart-

ment.

When lighting and re-lighting, the gas knob cannot be turned

from pilot to off unless the knob is depressed slightly.

1. Stop! Read the above safety information on this label.

2. Turn off all electric power to the fireplace.

3. Turn the gas knob clockwise

to off.

4. Wait five (5) minutes to clear out any gas. If you smell gas

including near the floor. Stop! Follow "B" in the above safety

information on this label. If you don't smell gas go the next step.

5. If fireplace is equipped with flame adjustment valve turn

clockwise to off.

6. Find pilot located in front of back log.

2. Push in gas control knob slightly and turn clockwise

to off. Do not force.

1. Turn off all electrical power to the unit if service is to be

performed.

TURN OFF THE GTURN OFF THE G

TURN OFF THE G

AS AND UNPLAS AND UNPL

AS AND UNPL

UG ELECTRICAL POUG ELECTRICAL PO

UG ELECTRICAL PO

WERWER

WER

BEFORE SERBEFORE SER

BEFORE SER

VICING THE FIREPLVICING THE FIREPL

VICING THE FIREPL

CE INSERCE INSER

CE INSER

T!T!

CAUTION: Label all wires prior to disconnection when serv-

icing controls. Wiring errors can cause improper and dan-

gerous operation. Verify proper operation after servicing.

This insert and its venting system should be inspected

before use and at least annually by a qualified service per-

son. The fireplace area must be kept clear and free of

combustible materials, gasoline or other flammable va-

pours and liquids. The flow of combustion and ventilation

air must not be obstructed.

1. In order to properly clean the burner and pilot assembly,

remove the logs exposing both assemblies.

2. Keep the control compartment, logs, burner, air shutter open-

ing and the area surrounding the logs clean by vacuuming

or brushing, at least once a year.

3. Check to see that all burner ports are burning. Clean out

any of the ports which may not be burning or are not burning

properly.

4. Check to see that the pilot flame is large enough to engulf

the thermocouple on one leg and reaches toward the burner

on the other leg.

5. Replace the cleaned logs.

6. Check to see that the main burner ignites completely on all

openings when the gas knob for the burner is turned on. A

5-10 second total light-up period is satisfactory. If ignition

takes longer, consult your Continental dealer/distributor.

7. Check that the door gasketing is not broken or missing.

Replace if necessary.

OPERATION / MAINTENANCE

WHAT TO DO IF YOU SMELL GAS:

OPERATING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING:

LIGHTING INSTRUCTIONS

TO TURN OFF GAS

MAINTENANCE

FIGURE 19

FIGURE 20

W415-0224 / D / 01.15.04

1. Turn off the electrical power and the gas supply to the

fireplace insert.

2. Remove the fire viewing door. Remove the logs.

3. Detach the two screws from the back of the firebox and

remove the panel, as illustrated.

4. Remove the blower access door held on with the re-

maining 8 screws. Replace the blower access door gas-

ket when changing the blower.

FIGURE 21

4. Disconnect the two blower wires. Remove the blower

bracket secured with one wing nut and lock washer.

For thermodisc replacement: Remove the "Z" shaped

mounting bracket secured to the firebox wall to the left of

the blower. Remove the thermodisc from the bracket and

replace.

5. Replace the blower using the existing bracket. Slide the

vibration reducing pad (A) into the clip (C) and up against

the threaded stud (B) at the other end. The blower must be

able to be positioned entirely onto the pad.

Slide the blower into the clip (C). Secure to the threaded

stud using the existing lock washer and wing nut. Ensure

that the blower does not touch the fireplace base or the

firebox.

6. Reconnect the two wires. Holding the replacement gas-

ket in place, reattach the blower access door and panel.

Replace the logs. Re-install the fire viewing door.

7. Turn the gas supply and electricity back on.

Drywall dust will penetrate into the blower bearings caus-

ing irreparable damage and must be prevented from

coming into contact with the blower or its compartment.

Any damage resulting from this condition is not cov-

ered by the warranty policy.

red

white

black

BLOWER

WIRES

FIGURE 24

THERMODISC

BRACKET

ASSEMBLY

FIGURE 26

FIGURE 25

B C

REPLACEMENT BLOWER INSTALLATION

FIGURE 22

FIGURE 23

BLOWER ACCESS DOOR

The Napoleon gas fireplace insert comes standard with a

blower, a heat sensor, variable on/off speed control and a

power cord. Because the blower is thermally activated,

when turned on, it will automatically start approximately 15

minutes after lighting the fireplace and will run for approxi-

mately 30 minutes after the fireplace has been turned off.

Use of the fan increases the output of heat. Air, drawn in

through the lower slot, is driven up the back of the firebox,

and exhausted as hot air through the upper slot.

W415-0224 / D / 01.15.04

Remove the pilot screw cap. Adjust the pilot screw to pro-

vide properly sized flame. Turn in a clockwise direction to

reduce the gas flow. Replace the pilot screw cap.

FIGURE 27

Air shutter adjustment

must only be done by a

qualified gas installer!

FIGURE 30

This unit is approved for use with a 2" liner for air intake

and a 3" liner for exhaust. For best performance, however,

it is recommended to use two 3" liners.

Air shutter settings will differ depending on the liner sys-

tem used. Use the charts below to determine the correct

air shutter setting:

Some vent configurations may display a very active flame. If

this appearance is not desirable, the vent exit may be re-

stricted using the restrictor plate shown in FIGURE 6b. Bend

the flap up as shown to reduce the velocity of the exhaust

gases, slowing down the flame pattern and creating a more

traditional appearance.

FIGURE 29

Closing the air shutter will cause a more yellow flame, but

can lead to carboning. Opening the air shutter will cause a

more blue flame, but can cause flame lifting from the burner

ports. The flame may not appear yellow immediately; allow

15 to 30 minutes for the final flame colour to be estab-

lished.

FIGURE 28

ADJUSTMENTS

PILOT BURNER ADJUSTMENT

VENTURI ADJUSTMENT

VENT RESTRICTION

HELPFUL HINT:

A mirror will let you see the opening of

the air shutter without removing the

burner. Scribe a line along the venturi

tube and air shutter cap. Open or close

according to the original opening by

using the scribed line as your datum.

3"/ 3" LINER SYSTEM

NG 1

LP 3

AIR SHUTTER SETTING

2"/ 3" LINER SYSTEM

NG 1

LP 5

AIR SHUTTER SETTING

W415-0224 / D / 01.15.04

31* W690-0001 MILLIVOLT THERMOSTAT

32* W660-0010 REMOTE CONTROL - ADVANTAGE

32* W660-0011 REMOTE CONTROL - ADVANTAGE PLUS

33* GD660 REMOTE WALL SWITCH C/W 20FT WIRE

34 GI-790KT DECORATIVE BRICK PANELS

35* W175-0162 CONVERSION KIT - NG-LP

35* W175-0192 CONVERSION KIT - LP-NG

36* GIZBP6-3 3 SIDED BACKER PLATE C/W ACCENT TRIM

37* GIZBP6-4 4 SIDED BACKER PLATE C/W ACCENT TRIM

38* GIZTRM3 ALUMINIUM EXTRUSION - MATTE BLACK

38* GIZTRM3-K ALUMINIUM EXTRUSION - POLISHED BLACK

38* GIZTRM3-B ALUMINIUM EXTRUSION - POLISHED BRASS

39 GIZTRM4 ALUMINIUM EXTRUSION - MATTE BLACK

39 GIZTRM4-K ALUMINIUM EXTRUSION - POLISHED BLACK

39 GIZTRM4-B ALUMINIUM EXTRUSION - POLISHED BRASS

40 GIZUT-B UPPER DOOR TRIM - BRASS

40 GIZUT-G UPPER DOOR TRIM - GOLD

41 GI-900K6 6" DELUXE FLASHING W MARQUIS TRIM - BLACK

41 GI-900B6 6" DELUXE FLASHING W MARQUIS TRIM - POLISHED BRASS

41 GI-900AB6 6" DELUXE FLASHING W MARQUIS TRIM - ANTIQUE BRASS

41 GI-900SS6 6" DELUXE FLASHING W MARQUIS TRIM - BRUSHED STAINLESS STEEL

41 GI-909S6 6" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN ALMOND

41 GI-909K6 6" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN BLACK

41 GI-909F6 6" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN GREEN

41 GI-900K9 9" DELUXE FLASHING W MARQUIS TRIM - BLACK

41 GI-900B9 9" DELUXE FLASHING W MARQUIS TRIM - POLISHED BRASS

41 GI-900AB9 9" DELUXE FLASHING W MARQUIS TRIM - ANTIQUE BRASS

41 GI-900SS9 9" DELUXE FLASHING W MARQUIS TRIM - BRUSHED STAINLESS STEEL

41 GI-909S9 9" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN ALMOND

41 GI-909K9 9" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN BLACK

41 GI-909F9 9" DELUXE FLASHING W MARQUIS TRIM - PORCELAIN GREEN

42* GIZBRKT MOUNTING BRACKETS (REQUIRED FOR THE 900 SERIES FLASHING KITS)

43 CISK-A CAST IRON SURROUND KIT - PAINTED BLACK

43 CISKK-A CAST IRON SURROUND KIT - PORCELAIN ENAMEL BLACK

43 CISKN-A CAST IRON SURROUND KIT - PORCELAIN ENAMEL MAJOLICA BROWN

43 CISKF-A CAST IRON SURROUND KIT - PORCELAIN ENAMEL MAJOLICA GREEN

44* AK-4 ADAPTOR KIT FOR CAST IRON SURROUND

45 ANI-K ANDIRON - PAINTED BLACK

45 ANI-G ANDIRON - GOLD PLATED

When ordering replacement parts always give the follow-

ing information:

1. MODEL & SERIAL NUMBER OF FIREPLACE

2. INSTALLATION DATE OF FIREPLACE

3. PART NUMBER

4. DESCRIPTION OF PART

5. FINISH

Contact your dealer for questions concerning prices and

availability of replacement parts. Normally all parts can be

ordered through your Continental dealer or distributor.

1 W725-0039 RBT SHAW VALVE - NG

1 W725-0040 RBT SHAW VALVE - LP

2 W100-0068 BURNER

3 W455-0017 #42 BURNER ORIFICE - NG

3 W455-0059 #53 BURNER ORIFICE - LP

4 W010-0800 PILOT ASSEMBLY - LP

4 W010-0801 PILOT ASSEMBLY - NG

5 W455-0069 PILOT INJECTOR - NG

5 W455-0067 PILOT INJECTOR - LP

6 W680-0005 THERMOCOUPLE

7 W680-0004 THERMOPILE

8* W573-0008 HIGH TEMPERATURE SEALANT

9* W357-0001 PIEZO IGNITOR

10 GL-631 LOG SET

11 W135-0136 REAR LOG

12 W135-0138 RIGHT LOG

13 W135-0137 LEFT LOG

14 W135-0139 CENTER LOG

15* W361-0016 GLOWING EMBERS

16 GZ552 BLOWER

17* W385-0131 CONTINENTAL LOGO

18* W010-0804 DOOR GLASS C/W GASKET

19* W225-0095 DOOR FRAME

20 W010-0802 DOOR C/W GLASS

21* W290-0063 BLOWER ACCESS GASKET

22* W430-0013 MAGNETIC CLOSURE

23* W660-0009 ON/OFF SWITCH

24* W690-0002 THERMODISC

25* W380-0002 VARIABLE SPEED SWITCH KNOB

26* KB35 VARIABLE SPEED SWITCH

27 W080-0451 RESTRICTOR BRACKET

28 GDI-223 TERMINAL KIT

REPLACEMENTS

FOR WARRANTY REPLACEMENT PARTS , A PHOTOCOPY OF THE ORIGINAL INVOICE WILL BE REQUIRED TO HONOUR THE CLAIM.

REPLACEMENT PARTS

TERMINAL KITS

ACCESSORIES:

1-2" & 1-3" DOUBLE PLY ALUMINUM LINER-INLET AND

EXHAUST & 2-3" TO 2" REDUCER:

29* GDI-2320KT VENT KIT 20FT

29* GDI-2325KT VENT KIT 25FT

29* GDI-2335KT VENT KIT 35FT

2-3" DOUBLE PLY ALUMINUM LINER-INLET AND

EXHAUST:

30* GDI-320KT VENT KIT 20FT

30* GDI-325KT VENT KIT 25 FT

30* GDI-335KT VENT KIT 35 FT

VENT KITS

* IDENTIFIES ITEMS WHICH ARE NOT ILLUSTRATED. FOR

FURTHER INFORMATION, CONTACT YOUR CONTINENTAL

DEALER.

W415-0224 / D / 01.15.04

* WARNING: This is a fast acting thermocouple. It is an integral safety component. Replace only

with a fast acting thermocouple supplied by Wolf Steel Ltd.

W415-0224 / D / 01.15.04

Main burner goes out;

pilot stays on.

Pilot flame is not large enough

or not engulfing the thermopile.

Thermopile shorting

Remote wall switch wire is too

long, too much resistance in

the system

Faulty thermostat or switch

- turn up pilot flame.

- replace pilot assembly.

- clean thermopile and thermopile connection to valve.

- shorten wire to correct length or wire gauge.

- replace

Gas piping is undersized.

Pilot goes out while

standing; Main burner

is in 'OFF' position.

- turn on all gas appliances and see if pilot flame flutters,

diminishes or extinguishes, especially when main burner ig-

nites. Monitor supply pressure.

- check if supply piping size is to code. Correct all undersized

piping.

Pilot burning; no gas

to main burner; gas

knob is on 'HI'; wall

switch / thermostat is

on.

Main burner orifice is plugged.

Faulty thermopile.

Faulty themostat or switch.

- remove stoppage in orifice.

- replace.

- connect a jumper wire across the wall switch terminals; if

main burner lights, replace thermostat.

- disconnect the switch wires & connect a jumper wire across

terminals 1 & 3; if the main burner lights, check the wires for

defects and / or replace wires.

Faulty valve.

- replace.

- check that the manual valve is turned on.

- check the pilot orifice for blockage.

- replace the valve.

- call the gas distributor.

No gas at the pilot burner

- fill the tank.

Out of propane gas.

Pilot will not light.

- check if pilot can be lit by a match

- check that the wire is connected to the push button ignitor.

- check if the push button ignitor needs tightening.

- replace the push button ignitor.

No spark at pilot burner

Spark gap is incorrect

- spark gap should be 0.150" to 0.175" (5/32" to 11/64" approx.)

from the electrode tip and the pilot burner.

Pilot flame is not large enough

- turn up the pilot flame.

Pilot flame is not engulfing the

thermocouple.

- turn up pilot flame.

- replace pilot assembly.

Thermocouple shorting.

Faultly thermocouple.

Faulty valve.

System is not correctly purged.

- purge the gas line with the glass door open.

- fill the tank.

Out of propane gas

Pilot goes out when

the gas knob is re-

leased.

- loosen and tighten thermocouple.

- clean thermocouple and valve connection.

- replace thermocouple.

- replace valve.

- replace.

TROUBLE SHOOTING GUIDE

EFORE

ATTEMPTING

TROUBLESHOOT

PURGE

YOUR

UNIT

AND

INITIALLY

LIGHT

THE

PILOT

AND

THE

MAIN

BURNER

WITH

THE

GLASS

DOOR

REMOVED

SYMPTOM PROBLEM TEST SOLUTION

W415-0224 / D / 01.15.04

Exhaust fumes

smelled in room,

headaches.

- check all seals.

Fireplace is spilling.

Carbon is being de-

posited on glass,

logs or combustion

chamber surfaces.

Flame is impinging on the

logs or combustion chamber.

- check that the logs are correctly positioned.

- open air shutter to increase the primary air.

- check the input rate: check the manifold pressure and orifice

size as specified by the rating plate values.

- check that the door gasketing is not broken or missing and

that the seal is tight.

- check that both vent liners are free of holes and well sealed at

all joints.

Air shutter has become

blocked

- ensure air shutter opening is free of lint or other obstruc-

tions.

White / grey film

forms.

Sulphur from fuel is being de-

posited on glass, logs or com-

bustion chamber surfaces.

- clean the glass with a recommended gas fireplace glass

cleaner. DO NOT CLEAN GLASS WHEN HOT.

If deposits are not cleaned off regularly, the glass may be-

come permanently marked.

Main burner goes out;

pilot goes out.

REFER TO "MAIN BURNER GOES OUT; PILOT STAYS ON"

Thermocouple shorting or

faulty.

Vent re-circulating

- check joint seals and installation.

- loosen and tighten thermocouple

- clean thermocouple and valve connection.

- replace thermocouple.

- replace valve.

Vent is reversing

- check all venting and insert seals.

- check that door is properly sealed. If the insert is allowed to

burn with the door off when purging the unit, exhaust products

may escape through the air intake pipe and reverse the venting

action. Let the unit cool down to correct the reversed venting

action.

Main burner flame is

a blue, lazy, transpar-

ent flame.

Blockage in vent. - remove blockage. In really cold conditions, ice buildup may

occur on the terminal and should be removed as required.

- vent liners are reversed. Refer to Figure 2.

- check all venting and insert seals.

Incorrect installation.

SYMPTOM PROBLEM TEST SOLUTION

Air shutter is not set to specifi-

cations.

- check and adjust air shutter to correspond with the fuel type

and air intake size.

W415-0224 / D / 01.15.04

Wolf Steel Fireplace Service History

This fireplace must be serviced annually depending on usage.

Date

Service Technician

Name

Service Performed Special ConcernsDealer Name

Continental CDIZC - N User manual

Brand: Continental

Model: CDIZC - N

Category: Fireplaces

Type: User manual

This manual is also suitable for

CDIZC - P

Download PDF

report

Continental CDIZC - N User manual

This manual is also suitable for

Continental CDIZC - N User manual

Related papers

Other documents