Bryant 355AAV EVOLUTION Troubleshooting guide

Brand: Bryant

Model: 355AAV EVOLUTION

Category: Water heaters & boilers

Type: Troubleshooting guide

This manual is also suitable for

- 1 -

troubleshooting guide

355MAV

Variable Speed, Two-Stage Series H & I

Electronic Condensing 355AAV

Gas Furnace 355BAV

Cancels: SM05-5 SM05-07

6-08

INDEX

PAGE

Safety Considerations................................................................................. 1

Instructions.................................................................................................. 1

Example ...................................................................................................... 2

General........................................................................................................ 2

Sequence of Operation ............................................................................... 2

Single-Stage Thermostat and Two-Stage Heating (Adaptive

Mode) ................................................................................................. 2

Two-Stage Thermostat and Two-Stage Heating .............................. 4

Cooling Mode .................................................................................... 4

Single-Speed Cooling ........................................................................ 4

Single-Stage Thermostat and Two-Speed Cooling (Adaptive

Mode) ................................................................................................. 4

Two-Stage Thermostat and Two-Speed Cooling ............................. 5

Thermidistat Mode............................................................................. 5

Super-Dehumidify Mode................................................................... 5

Continuous-Blower Mode ................................................................. 6

Heat Pump Defrost............................................................................. 6

Component Test................................................................................. 6

Service/Status Code Instructions ............................................................... 7

Start Here .................................................................................................... 9

Rapid Flashing AMBER LED................................................................. 10

Improper Cooling Air Flow ..................................................................... 11

High Heat Temperature Rise Too Low ................................................... 12

Status Code 11 - No Previous Code......................................................... 13

Status Code 12 - Blower On After Power Up ......................................... 13

Status Code 13 - Limit Circuit Lockout .................................................. 14

Status Code 14 - Ignition Lockout ........................................................... 15

Status Code 15 – Blower Motor Lockout................................................ 15

Status Code 21 - Gas Heating Lockout.................................................... 15

Status Code 22 - Abnormal Flame-Proving Signal................................. 16

Status Code 23 - Pressure Switch Did Not Open .................................... 16

Status Code 24 - Secondary Voltage Fuse Is Open................................. 17

Status Code 25 – Model Selection or Setup Error................................... 19

Status Code 31 – High-Heat Switch or Relay did not close or

Reopen.............................................................................................. 19

Status Code 32 - Low-Heat Pressure Switch Did Not Close or

Reopened.......................................................................................... 21

Status Code 33 - Limit Circuit Fault........................................................ 23

Status Code 34 - Ignition-Proving Fault.................................................. 25

Status Code 41 – Blower Motor Fault ..................................................... 26

Status Code 42 – Inducer Motor Fault..................................................... 28

Status Code 43 - Low-Heat Pressure Switch Open While High-Heat

Pressure Switch Is Closed................................................................ 30

Status Code 45 – Control Circuitry Lockout........................................... 31

Cleanup and Start-Up Instructions........................................................... 31

APPENDIX A - Board Layout & Wiring Schematic ............................. 32

APPENDIX B - ECM Blower Motor Description & Operation............ 36

APPENDIX C - Pressure Check Diagram .............................................. 37

APPENDIX D - Static Pressure Reading Location Diagrams................ 38

APPENDIX E - Quick Reference Information ....................................... 40

APPENDIX F - Furnace Staging Algorithm........................................... 41

SAFETY CONSIDERATIONS

Installing and servicing heating equipment can be hazardous due to

gas and electrical components. Only trained and qualified personnel

should install, repair, or service heating equipment.

Untrained personnel can perform basic maintenance functions such as

cleaning coils, or cleaning and replacing filters. All other operations

should be performed by trained service personnel. When working on

heating equipment, observe precautions in literature, on tags, and on

labels attached to or shipped with the unit, and other safety

precautions that may apply.

Follow all safety codes. In the United States, follow all safety codes

including the National Fuel Gas Code (NFGC) NFPA 54-2006/ANSI

Z223.1-2006. In Canada, refer to the National Standard of Canada

Natural Gas and Propane Installation Codes (NSCNGPIC), CSA

B149.1-05.

Wear safety glasses and work gloves. Have a fire extinguisher

available during start-up, adjustment procedures, and service calls.

Recognize safety information. This is the safety-alert symbol .

When you see this symbol on the furnace and in instructions or

manuals, be alert to the potential for personal injury.

Understand the signal words DANGER, WARNING, and CAUTION,

and NOTE. The words DANGER, WARNING, and CAUTION are

used with the safety-alert symbol. DANGER identifies the most

serious hazards which will result in severe personal injury or death.

WARNING signifies hazards which could result in personal injury or

death. CAUTION is used to identify unsafe practices which may

result in minor personal injury, or product and property damage.

NOTE is used to highlight suggestions which will result in enhanced

installation, reliability, or operation.

INSTRUCTIONS

This guide uses your expertise and observations to lead you to the

trouble spot as efficiently as possible. This is only intended as a guide

and should not be used blindly. Your experience and expertise are of

high value when troubleshooting this unit. Do not disregard all of

your instincts.

The variable speed furnace control was designed with diagnostic

capabilities built in. A AMBER LED is used to flash a status code

which will lead you to one of the sections as listed in the Index.

You should ALWAYS begin in the START HERE section (see Index

for page number) which will guide you to the appropriate section

where a minimal number of steps will be used to correct the problem.

Once in a section, read the ACTION. An ACTION may have a

- 2 -

number in the GO TO column. Do whatever the ACTION says, then

proceed to the step indicated in the GO TO column.

If the ACTION is a question (a question will have a number in the

YES or NO column), answer it YES or NO. If the answer is YES, go

to the step indicated in the YES column. If the answer is NO, go to

the step indicated in the NO column.

Let’s try our guide out using the EXAMPLE section below, and see

how it works. Suppose that the problem is a defective low heat

pressure switch (for example the contacts will not open). This is an

internal problem and cannot simply be seen. We go to the START

HERE section to Step 1.

EXAMPLE

Start Here Section

STEP ACTION YES NO GO TO

1. Step 1 tells us to remove main furnace door first and NOT TO REMOVE THE BLOWER

ACCESS PANEL. It then asks the question, “Is AMBER LED status light on?”. If the low

heat pressure switch was defective, a pressure switch did not open status code would be

flashing, so the answer is YES. We go to Step 2.

2 19

2. Step 2 asks the question, “Is the AMBER LED status light blinking rapidly without a pause?”.

If the low heat pressure switch was defective, a pressure switch did not open status code would

be flashing, so the answer is NO. We go to Step 4.

3 4

4. Step 4 asks the question, “Is the AMBER LED status light blinking ON/OFF slowly with a

combination of short and long flashes?”. If the low heat pressure switch was defective, a

pressure switch did not open status code would be flashing, so the answer is YES. We go to

Step 5.

5 7

5. Step 5 tells us to determine the status code. The status code is a 2 digit number with the first

digit determined by the number of short flashes and the second digit by the number of long

flashes. So we count the short and long flashes and see that status code 23 is flashing and go to

Step 6.

6. Step 6 tells us to go to status code 23 section INDEX

GENERAL

The furnace must have a 115-vac power supply properly connected

and grounded. Correct polarity must be maintained to enable gas

heating operation.

The gas service pressure must not exceed 0.5 psig (14-in.wc), and no

less than 0.16 psig (4.5-in.wc).

Thermostat wire connections to the furnace at R and W/W1 are the

minimum required for gas heating operation. W2 must be connected

for 2-stage heating thermostats. Y/Y2 and G are required to be

connected to the furnace for single-stage cooling and heat pumps. Y1,

Y/Y2, and G are required for two-stage cooling and heat pumps. G is

required for continuous-fan. C

OM-24V is required for some clock

thermostats. These connections must be made at the 24-vac terminal

block on the furnace control. (See Appendix A)

This furnace can be installed with either a single-stage heat/cool or a

two-stage heat/cool thermostat.

CAUTION: This furnace is equipped with a manual

reset switch in the gas control area. The switch will open

and shut off power to the gas valve, if a flame rollout or

overheating condition occurs in the gas control area. DO

NOT bypass the switch. Correct inadequate combustion-

air supply, component failure before resetting the switch.

Before operating the furnace, check each manual reset switch for

continuity. If necessary, press and release the button to reset the

switch.

SEQUENCE OF OPERATION

Using the schematic diagram in Appendix A, follow the sequence of

operation through the different modes. Read and follow the wiring

diagram very carefully.

Note: If a power interruption occurs during a call for heat (W/W1 or

W/W1-and-W2), the control will start a 90-second blower-only ON

period two seconds after power is restored, if the thermostat is still

calling for gas heating. The amber LED light will flash code 12

during the 90-second period, after which the LED will be ON

continuous, as long as no faults are detected. After the 90-second

period, the furnace will respond to the thermostat normally.

The blower access panel must be installed for power to be conducted

through the blower door interlock switch ILK to the furnace control

CPU, transformer TRAN, inducer motor IDM, blower motor BLWM,

hot-surface igniter HSI, and gas valve GV.

1. SINGLE-STAGE THERMOSTAT AND TWO-STAGE

HEATING (ADAPTIVE MODE)

Note: The low-heat only switch SW1-2 selects either the low-

heat only operation mode when ON, (see item 2. below) or the

adaptive heating mode when OFF in response to a call for heat.

(See Fig. 1.) When the W2 thermostat terminal is energized it

will always cause high-heat operation when the R to W circuit

is closed, regardless of the setting of the low-heat only switch.

This furnace can operate as a two-stage furnace with a single-

stage thermostat because the furnace control CPU includes a

programmed adaptive sequence of controlled operation, which

selects low-heat or high-heat operation. This selection is based

upon the stored history of the length of previous gas-heating

periods of the single-stage thermostat.

- 3 -

The furnace will start up in either low- or high-heat. If the

furnace starts up in low-heat, the control CPU determines the

low-heat on-time (from 0 to 16 minutes) which is permitted

before switching to high-heat.

If the power is interrupted, the stored history is erased and the

control CPU will select low-heat for up to 16 minutes and then

switch to high-heat, as long as the thermostat continues to call

for heat. Subsequent selection is based on stored history of the

thermostat cycle times.

The wall thermostat "calls for heat", closing the R to W circuit.

The furnace control performs a self-check, verifies the low-heat

and high-heat pressure switch contacts LPS and HPS are open.

a. Inducer Prepurge Period - The furnace control CPU

turns on inducer motor IDM and slowly increases the

inducer motor speed. When the low-heat pressure switch

LPS closes, inducer motor RPM is noted by the furnace

control CPU, and a 25-second prepurge period begins. The

RPM is used to evaluate vent system resistance. This

evaluation is then used to determine the required RPM

necessary to operate the inducer motor during the low-heat

prepurge period and low-heat mode.

Note: The heat cycle can start in either high- or low-heat.

If a high-heat cycle is initiated, the furnace control CPU

will de-energize the high-heat pressure switch relay HPSR

to close the NC contact and continues to increase the

inducer motor speed after the low-heat pressure switch LPS

closes. When the high-heat pressure switch closes, inducer

motor RPM is noted by the furnace control CPU, and a 25-

second prepurge period begins. The RPM is used to

evaluate vent system resistance. This evaluation is then

used to determine the required RPM necessary to operate

the inducer motor in high-heat mode.

b. Igniter Warm-Up - At the end of the prepurge period, the

Hot-Surface Igniter HSI is energized for a 17-second igniter

warm-up period.

c. Trial-For-Ignition Sequence - When the igniter warm-up

period is completed the main gas valve relay contact GVR

closes to energize the gas valve solenoid GV-M. The gas

valve solenoid GV-M permits gas flow to the burners where

it is ignited. After 5 seconds, the igniter HSI is de-

energized and a 2-second Flame-Proving period begins.

If the furnace control CPU selects high-heat operation, the

high-heat gas valve solenoid GV-HI is also energized.

d. Flame-Proving - When the burner flame is proved at the

flame-proving sensor electrode FSE, the furnace control

CPU begins the blower-ON delay period and continues to

hold the gas valve GV-M open. If the burner flame is not

proved within two seconds, the control CPU will close the

gas valve GV-M, and the control CPU will repeat the

ignition sequence for up to three more Trials-For-Ignition

before going to Ignition-Lockout. Lockout will be reset

automatically after three hours, by momentarily interrupting

115 vac power to the furnace, or by interrupting 24 vac

power at SEC1 or SEC2 to the furnace control CPU (not at

W/W1, G, R, etc.).

If flame is proved when flame should not be present, the

furnace control CPU will lock out of Gas-Heating mode

and operate the inducer motor IDM at full speed until

flame is no longer proved.

e. Inducer Speed Change – If the cycle starts in low-heat, the

furnace control CPU reduces the inducer speed slightly

after flame sense. If the cycle starts in high-heat, the

furnace control CPU increases the inducer speed 15

seconds after flame sense. The reduction in speed in low-

heat is to optimize combustion for maximum efficiency.

f. Blower-On delay – If the burner flame is proven the

blower-ON delay for low-heat and high-heat are as follows:

Low-heat:

355MAV and 355AAV – 60 seconds after the gas valve

GV-M is opened the blower motor BLWM is turned ON at

low-heat airflow.

355BAV – 30 seconds after the gas valve GV-M is opened

the blower motor BLWM is turned ON at low-heat

airflow.

High-heat – 35 seconds after the gas valve GV-M is

opened the BLWM is turned ON at high-heat airflow.

Simultaneously, the humidifier terminal HUM and

electronic air cleaner terminal EAC-1 are energized and

remain energized throughout the heating cycle.

g. Switching from Low- to High-Heat - If the furnace

control CPU switches from low-heat to high-heat, the

furnace control CPU will de-energize the high-heat

pressure switch relay HPSR to close the NC contact and

slowly increase the inducer motor speed until the high-heat

pressure switch HPS closes. When the high-heat pressure

switch HPS closes, the high-heat gas valve solenoid GV-

HI is energized and the inducer motor RPM is noted by the

furnace control CPU. The RPM is used to evaluate vent

system resistance. This evaluation is then used to

determine the required RPM necessary to operate the

inducer motor in high-heat mode. The blower motor

BLWM will transition to high-heat airflow five seconds

after the furnace control CPU switches from low-heat to

high-heat.

Switching from High- to Low-Heat – The furnace

control CPU will not switch from high-heat to low-heat

while the thermostat R to W circuit is closed when using a

single-stage thermostat.

h. Blower-Off Delay - When the thermostat is satisfied, the

R to W circuit is opened, de-energizing the gas valve GV-

M, stopping gas flow to the burners, and de-energizing the

humidifier terminal HUM. The inducer motor IDM will

remain energized for a 15-second post-purge period. The

blower motor BLWM and air cleaner terminal EAC-1 will

remain energized at low-heat airflow or transition to low-

heat airflow for 90, 120, 150, or 180 seconds (depending on

selection at blower-OFF delay switches). The furnace

control CPU is factory-set for a 120-second blower-OFF

delay.

- 4 -

2. TWO-STAGE THERMOSTAT AND TWO-STAGE

HEATING

Note: In this mode the low-heat only switch SW1-2 must be

ON to select the low-heat only operation mode in response to

closing the thermostat R to W1 circuit. Closing the thermostat

R to W1-and-W2 circuits always causes high-heat operation,

regardless of the setting of the low-heat only switch.

The wall thermostat "calls for heat", closing the R to W1 circuit

for low-heat or closing the R to W1-and-W2 circuits for high-

heat. The furnace control performs a self-check, verifies the

low-heat and high-heat pressure switch contacts LPS and HPS

are open, and starts the inducer motor IDM in high-speed.

The start up and shut down functions and delays described in

item 1. above apply to the 2-stage heating mode as well, except

for switching from low- to high-Heat and vice versa.

a. Switching from Low- to High-Heat - If the thermostat

R to W1 circuit is closed and the R to W2 circuit closes, the

furnace control CPU will de-energize the high-heat

pressure switch relay HPSR to close the NC contact and

slowly increase the inducer motor speed until the high-heat

pressure switch HPS closes. When the high-heat pressure

switch HPS closes, the high-heat gas valve solenoid GV-

HI is energized and the inducer motor RPM is noted by the

furnace control CPU. The RPM is used to evaluate vent

system resistance. This evaluation is then used to

determine the required RPM necessary to operate the

inducer motor in high-heat mode. The blower motor

BLWM will transition to high-heat airflow five seconds

after the furnace control CPU switches from low-heat to

high-heat.

b. Switching from High- to Low-Heat - If the thermostat

R to W2 circuit opens, and the R to W1 circuit remains

closed, the furnace control CPU will energize the high-heat

pressure switch relay HPSR to open the NC contact and

slowly decrease the inducer motor speed to the required

low-heat RPM . When the high-heat pressure switch HPS

opens, the high-heat gas valve solenoid GV-HI is de-

energized. When the inducer motor IDM reduces pressure

sufficiently, the high-heat pressure switch HPS will open.

The gas valve solenoid GV-M will remain energized as

long as the low-heat pressure switch LPS remains closed.

The blower motor BLWM will transition to low-heat

airflow five seconds after the R to W2 circuit opens.

3. COOLING MODE

The thermostat "calls for cooling".

a. Single-Speed Cooling

The thermostat closes the R to G-and-Y circuits. The R to

Y circuit starts the outdoor unit, and the R to G-and-Y/Y2

circuits start the furnace blower motor BLWM on cooling

airflow. Cooling airflow is based on the A/C selection

shown in Table 1.

The electronic air cleaner terminal EAC-1 is energized

with 115 vac when the blower motor BLWM is operating.

When the thermostat is satisfied, the R to G-and-Y circuits

are opened. The outdoor unit will stop, and the furnace

blower motor BLWM will continue operating at cooling

airflow for an additional 90 seconds. Jumper Y/Y2 to

DHUM to reduce the cooling off-delay to 5 seconds. (See

Fig. 1.)

b. Single-Stage Thermostat and Two-Speed Cooling

(Adaptive Mode)

This furnace can operate a two-speed cooling unit with a

single-stage thermostat because the furnace control CPU

includes a programmed adaptive sequence of controlled

operation, which selects low-cooling or high-cooling

operation. This selection is based upon the stored history

of the length of previous cooling period of the single-stage

thermostat.

Note: The air conditioning relay disable jumper ACRDJ

must be connected to enable the adaptive cooling mode in

response to a call for cooling. (See Fig. 1.) When in place

the furnace control CPU can turn on the air conditioning

relay ACR to energize the Y/Y2 terminal and switch the

outdoor unit to high-cooling.

The furnace control CPU can start up the cooling unit in

either low- or high-cooling. If starting up in low-cooling,

the furnace control CPU determines the low-cooling on-

time (from 0 to 20 minutes) which is permitted before

switching to high-cooling.

If the power is interrupted, the stored history is erased and

the furnace control CPU will select low-cooling for up to

20 minutes and then energize the air conditioning relay

ACR to energize the Y/Y2 terminal and switch the

outdoor unit to high-cooling, as long as the thermostat

continues to call for cooling. Subsequent selection is

based on stored history of the thermostat cycle times.

The wall thermostat “calls for cooling”, closing the

R to G-and-Y circuits. The R to Y1 circuit starts the

outdoor unit on low-cooling speed, and the R to G-and-Y1

circuits starts the furnace blower motor BLWM at low-

Table 1 - Cooling Tonnage vs. Airflow (CFM)

525

700

875 1050

875

700 875

1050

1225

1400

1225

1750

1225

1750

2100

DEF.

040, 060, 3T-080

5T-080, 100

120

BASED ON 350 CFM/TON (SETUP SWITCH SW1-5 OFF)

SETUP SWITCH SW3 POSITIONS

MODEL

SIZE

600

800

1000 1200

1000

800 1000

1200

1400

1600

1400

2000

1400

2000

2100

DEF.

040, 060, 3T-080

5T-080, 100

120

BASED ON 400 CFM/TON (SETUP SWITCH SW1-5 ON)

1. DEFAULT A/C AIRFLOW WHEN A/C SWITCHES ARE IN OFF POSITION

2. DEFAULT CONT. FAN AIRFLOW WHEN CF SWITCHES ARE IN OFF POSITION

3. SWITCH POSITIONS ARE ALSO SHOWN ON FURNACE WIRING DIAGRAM

SETUP SWITCH SW3 POSITIONS

MODEL

SIZE

AIR CONDITIONING (A/C) OR CONTINUOUS-FAN (CF)

AIRFLOW SELECTION CHART

- 5 -

cooling airflow which is the true on-board CF selection as

shown in Table 1.

If the furnace control CPU switches from low-cooling to

high-cooling, the furnace control CPU will energize the air

conditioning relay ACR. When the air conditioning relay

ACR is energized the R to Y1-and-Y2 circuits switch the

outdoor unit to high-cooling speed, and the R to G-and-

Y1-and-Y/Y2 circuits transition the furnace blower motor

BLWM to high-cooling airflow. High-cooling airflow is

based on the A/C selection shown in Table 1.

Note: When transitioning from low-cooling to high-

cooling the outdoor unit compressor will shut down for 1

minute while the furnace blower motor BLWM transitions

to run at high-cooling airflow.

The electronic air cleaner terminal EAC-1 is energized

with 115 vac whenever the blower motor BLWM is

operating.

When the thermostat is satisfied, the R to G-and-Y circuit

are opened. The outdoor unit stops, and the furnace

blower BLWM and electronic air cleaner terminal EAC-1

will remain energized for an additional 90 seconds.

Jumper Y1 to DHUM to reduce the cooling off-delay to 5

seconds. (See Fig. 1.)

c. Two-Stage Thermostat and Two-Speed Cooling

Note: The air conditioning relay disable jumper ACRDJ

must be disconnected to allow thermostat control of the

outdoor unit staging. (See Fig. 1.)

The thermostat closes the R to G-and-Y1 circuits for low-

cooling or closes the R to G-and-Y1-and-Y2 circuits for

high-cooling. The R to Y1 circuit starts the outdoor unit

on low-cooling speed, and the R to G-and-Y1 circuit starts

the furnace blower motor BLWM at low-cooling airflow

which is the true on-board CF selection as shown in Table

1. The R to Y1-and-Y2 circuits start the outdoor unit on

high-cooling speed, and the R to G-and-Y/Y2 circuits start

the furnace blower motor BLWM at high-cooling airflow.

High-cooling airflow is based on the A/C selection shown

in Table 1.

The electronic air cleaner terminal EAC-1 is energized

with 115 vac whenever the blower motor BLWM is

operating.

When the thermostat is satisfied, the R to G-and-Y1 or

R to G-and-Y1-and-Y2 circuits are opened. The outdoor

unit stops, and the furnace blower BLWM and electronic

air cleaner terminal EAC-1 will remain energized for an

additional 90 seconds. Jumper Y1 to DHUM to reduce the

cooling off-delay to 5 seconds. (See Fig. 1.)

4. THERMIDISTAT MODE

The dehumidification output, DHUM on the Thermidistat

should be connected to the furnace control thermostat terminal

DHUM. When there is a dehumidify demand, the DHUM input

is activated, which means 24 vac signal is removed from the

DHUM input terminal. In other words, the DHUM input logic

is reversed. The DHUM input is turned ON when no

dehumidify demand exists. Once 24 vac is detected by the

furnace control on the DHUM input, the furnace control

operates in Thermidistat mode. If the DHUM input is low for

more than 48 hours, the furnace control reverts back to non-

Thermidistat mode.

The cooling operation described in item 3. above also applies to

operation with a Thermidistat. The exceptions are listed below:

a. When the R to G-and-Y1 circuit is closed and there is a

demand for dehumidification, the furnace blower motor

BLWM will drop the blower airflow to 86% of low-cooling

airflow which is the true on-board CF selection as shown in

Table 1.

b. When the R to G-and Y/Y2 circuit is closed and there is a

demand for dehumidification, the furnace blower motor

BLWM will drop the blower airflow to 86% of high-

cooling airflow. High-cooling airflow is based on the A/C

selection shown in Table 1.

c. When the “call for cooling” is satisfied and there is a

demand for dehumidification, the cooling blower-off delay

is decreased from 90 seconds to 5 seconds.

5. SUPER-DEHUMIDIFY MODE

Super-Dehumidify mode can only be entered if the furnace

control is in the Thermidistat mode and there is a demand for

dehumidification. The cooling operation described in item 3.

above also applies to operation with a Thermidistat. The

exceptions are listed below:

a. When the R to Y1 circuit is closed, R to G circuit is open,

and there is a demand for dehumidification, the furnace

blower motor BLWM will drop the blower airflow to 65%

of low-cooling airflow for a maximum of 10 minutes each

cooling cycle or until the R to G circuit closes or the

demand for dehumidification is satisfied. Low-cooling

airflow is the true on-board CF selection as shown in Table

b. When the R to Y/Y2 circuit is closed, R to G circuit is open,

and there is a demand for dehumidification, the furnace

blower motor BLWM will drop the blower airflow to 65%

of high-cooling airflow for a maximum of 10 minutes each

cooling cycle or until the R to G circuit closes or the

demand for dehumidification is satisfied. High-cooling

airflow is based on the A/C selection shown in Table 1.

c. When the “call for cooling” is satisfied and there is a

demand for dehumidification, the cooling blower-off delay

is decreased from 90 seconds to 5 seconds.

6. Continuous Blower Mode

When the R to G circuit is closed by the thermostat, the blower

motor BLWM will operate at continuous blower airflow.

Continuous blower airflow selection is initially based on the CF

selection shown in Table 1. Factory default is shown in Table

1. Terminal EAC-1 is energized as long as the blower motor

BLWM is energized.

During a call for heat, the furnace control CPU will transition

the blower motor BLWM to continuous blower airflow, low-

heat airflow, or the midrange airflow, whichever is lowest. The

- 6 -

blower motor BLWM will remain ON until the main burners

ignite then shut OFF and remain OFF for the blower-ON delay

(60 seconds in low-heat, and 35 seconds in high-heat), allowing

the furnace heat exchangers to heat up more quickly, then

restarts at the end of the blower-ON delay period at low-heat or

high-heat airflow respectively.

The blower motor BLWM will revert to continuous-blower

airflow after the heating cycle is completed. In high-heat, the

furnace control CPU will drop the blower motor BLWM to

low-heat airflow during the selected blower-OFF delay period

before transitioning to continuous-blower airflow.

When the thermostat "calls for low-cooling", the blower motor

BLWM will switch to low-cooling airflow. When the

thermostat is satisfied, the blower motor BLWM will operate an

additional 90 seconds at low-cooling airflow before

transitioning back to continuous-blower airflow.

When the thermostat "calls for high-cooling", the blower motor

BLWM will switch to high cooling airflow. When the

thermostat is satisfied, the blower motor BLWM will operate an

additional 90 seconds at high-cooling airflow before

transitioning back to continuous-blower airflow.

When the R to G circuit is opened, the blower motor BLWM

will continue operating for an additional 5 seconds, if no other

function requires blower motor BLWM operation.

a. Continuous Blower Speed Selection from Thermostat

To select different continuous-blower airflows from the

room thermostat, momentarily turn off the FAN switch or

push-button on the room thermostat for 1-3 seconds after

the blower motor BLWM is operating. The furnace

control CPU will shift the continuous-blower airflow from

the factory setting to the next highest CF selection airflow

as shown in Table 1. Momentarily turning off the FAN

switch again at the thermostat will shift the continuous-

blower airflow up one more increment. If you repeat this

procedure enough you will eventually shift the continuous-

blower airflow to the lowest CF selection as shown in

Table 1. The selection can be changed as many times as

desired and is stored in the memory to be automatically

used following a power interruption.

7. HEAT PUMP DEFROST

When installed with a heat pump, the furnace control

automatically changes the timing sequence to avoid long blower

off times during demand defrost cycles. Whenever W/W1 is

energized along with Y1 or Y/Y2, the furnace control CPU will

transition to or bring on the blower motor BLWM at cooling

airflow, low-heat airflow, or the midrange airflow, whichever is

lowest. The blower motor BLWM will remain on until the

main burners ignite then shut OFF and remain OFF for 25

seconds before coming back on at heating airflow. When the

W/W1 input signal disappears, the furnace control begins a

normal inducer post-purge period while changing the blower

airflow. If Y/Y2 input is still energized the furnace control

CPU will transition the blower motor BLWM airflow to cooling

airflow. If Y/Y2 input signal disappears and the Y1 input is still

energized the furnace control CPU will transition the blower

motor BLWM to low-cooling airflow. If both the Y1 and Y/Y2

signals disappear at the same time, the blower motor BLWM

will remain on at low-heat airflow for the selected blower-OFF

delay period. At the end of the blower-OFF delay, the blower

motor BLWM will shut OFF unless G is still energized, in

which case the blower motor BLWM will operate at continuous

blower airflow.

8. COMPONENT TEST

The furnace features a component test system to help diagnose

a system problem in the case of a component failure. To initiate

the component test procedure, ensure that there are no

thermostat inputs to the control and all time delays have

expired. Turn on setup switch SW1-6. (See Appendix A)

Note: The component test feature will not operate if the control

is receiving any thermostat signals or until all time delays have

expired.

The component test sequence is as follows:

a. The furnace control CPU turns the inducer motor IDM ON

at medium speed and keeps it ON through step c.

b. After waiting 10 seconds the furnace control CPU turns

the hot surface igniter ON for 15 seconds, then OFF.

c. The furnace control CPU then turns the blower motor

BLWM on at midrange airflow for 15 seconds, then OFF.

d. After shutting the blower motor OFF the furnace control

CPU shuts the inducer motor IDM.

Note: The EAC terminals are energized when the blower is

operating.

After the component test is completed, 1 or more status codes

(11, 25, 41, or 42) will flash. See Service Label on blower

access panel or Service/Status Code Instructions for explanation

of status codes.

Note: To repeat component test, turn setup switch SW1-6 to

OFF and then back ON.

- 7 -

SERVICE/STATUS CODE INSTRUCTIONS

If status code recall is needed disconnect the “R” thermostat lead, reset power, and put setup switch “SW1-1” in the ON position. To clear the status

code history put setup switch “SW1-1” in the ON position and jumper thermostat terminals “R”, “W/W1”, and “Y/Y2” simultaneously until status code

#11 is flashed.

LED CODE STATUS

CONTINUOUS OFF - Check for 115 VAC at L1 and L2, and 24 VAC at SEC-1 and SEC-2.

CONTINUOUS ON - Control has 24 VAC power.

RAPID FLASHING - Line voltage (115 VAC) polarity

reversed.

EACH OF THE FOLLOWING STATUS CODES IS A TWO DIGIT NUMBER WITH THE FIRST DIGIT DETERMINED BY THE

NUMBER OF SHORT FLASHES AND THE SECOND DIGIT BY THE NUMBER OF LONG FLASHES.

11 NO PREVIOUS CODE – Stored status codes are erased automatically after 72 hours or as specified above.

12 BLOWER ON AFTER POWER UP – (115 VAC or 24 VAC) – Blower runs for 90 seconds, if unit is powered up during a call for heat (R-

W/W1 closed) or (R-W/W1 opens) during the blower on-delay period.

13 LIMIT CIRCUIT LOCKOUT – Lockout occurs if the limit, or flame rollout switch is open longer than 3 minutes or 10 successive limit trips

occurred during high-heat. Control will auto reset after 3 hours. Refer to status code #33.

14 IGNITION LOCKOUT – Control will auto reset after 3 hours. Refer to status code #34.

15 BLOWER MOTOR LOCKOUT – Indicates the blower failed to reach 250 RPM or the blower failed to communicate within 30 seconds after

being turned ON in two successive heating cycles. Control will auto reset after 3 hours. Refer to status code #41.

21 GAS HEATING LOCKOUT – Control will NOT auto reset. Check for:

- Mis-wired gas valve.

- Defective control (valve relay).

22 ABNORMAL FLAME-PROVING SIGNAL – Flame is proved while gas valve is de-energized. Inducer will run until fault is cleared. Check

for:

- Leaky gas valve.

- Stuck-open gas valve.

23 PRESSURE SWITCH DID NOT OPEN – Check for:

- Obstructed pressure tubing.

- Pressure switch stuck closed.

24 SECONDARY VOLTAGE FUSE IS OPEN – Check for :

- Short circuit in secondary voltage (24 VAC) wiring.

25 MODEL SELECTION OR SETUP ERROR – Either Indicates the model plug (PL4) is missing or incorrect or setup switch “SW1-1” or

“SW1-6” is positioned improperly. If code flashes only 4 times on power-up control is defaulting to model selection stored in memory. Check

the following:

- Thermostat call with “SW1-1” ON.

- Thermostat call with “SW1-6” ON.

- “SW1-1” and “SW1-6” both ON together.

- Two different furnace models twinned.

- Wiring diagram for model plug number and resistance values if code flashes continuously.

- Board does not recognize 355BAV model plugs HK70EZ057 – 061. Furnace board date code 4106 or later required.

31 HIGH-HEAT PRESSURE SWITCH OR RELAY DID NOT CLOSE OR REOPENED – Indicates the high-heat pressure switch input

failed to close on a call for high-heat, or opened during high-heat. Control relay may be defective or gas valve is mis-wired. Refer to status code

#32.

32 LOW-HEAT PRESSURE SWITCH DID NOT CLOSE OR REOPENED – Indicates the low-heat pressure switch input failed to close on a

call for low-heat, or opened during low-heat. If opens during blower on-delay period , blower will come on for the selected blower off-delay. If

opens within 5 minutes after ignition the next heating cycle will be restricted to high-heat. Check for:

- Proper vent sizing.

- Plugged condensate drain.

- Low inlet gas pressure (if LGPS used).

- Excessive wind.

- Restricted combustion air supply.

- Improper pressure switch wiring.

- Failed or “Out-of-Calibration” pressure switches.

- Water in vent piping, possible sagging pipe.

- Disconnected or obstructed pressure tubing.

- 8 -

33 LIMIT CIRCUIT FAULT – Indicates the limit, or flame rollout is open or the furnace is operating in high-heat only mode due to 2 successive

low heat limit trips. Blower will run for 4 minutes or until open switch remakes whichever is longer. If open longer than 3 minutes, code changes

to lockout #13. If open less than 3 minutes status code #33 continues to flash until blower shuts off. Flame rollout switch requires manual reset.

Check for:

- Proper rear air baffle.

- Loose blower wheel.

- Defective switch or connections.

- Improper low-heat gas input adjustment.

- Stuck high-heat solenoid in gas valve

- Improper or misaligned limit and/or limit shield.

34 IGNITION PROVING FAILURE – Control will try three more times before lockout #14 occurs. If flame signal is lost during blower on-delay

period, blower will come on for the selected blower off-delay. Check for:

- Low inlet gas pressure.

- Control ground continuity.

- Gas valve defective or turned off.

- Defective Hot Surface Igniter.

- Manual valve shut off.

- Oxide buildup on flame sensor (clean with fine steel wool).

- Proper flame sense micro amps (.5 micro amps DC min., 4.0 – 6.0 nominal).

- Green/Yellow wire MUST be connected to furnace sheet metal.

- Inadequate flame carryover or rough ignition.

- Flame sensor must not be grounded.

41 BLOWER MOTOR FAULT – Indicates the blower failed to reach 250 RPM or the blower failed to communicate within the prescribed time

limits. Thirty seconds after being turned ON or ten seconds during steady-state operation.

42 INDUCER MOTOR FAULT – Indicates the inducer has not started within 20 seconds after a call for heat, the inducer motor RPM is outside its

valid range of operation, or the inducer RPM signal was lost for 5 seconds during operation. Check for:

- Proper vent sizing.

- Restricted combustion air supply.

- Failed inducer motor.

- Improper motor wiring.

43 LOW-HEAT PRESSURE SWITCH OPEN WHILE HIGH-HEAT PRESSURE SWITCH IS CLOSED – Check for:

- Low inlet gas pressure (if LGPS used).

- Plugged condensate drain.

- Improper pressure switch wiring.

- Water in vent piping, possible sagging pipe.

- Stuck open low-heat pressure switch.

- Disconnected or obstructed pressure tubing.

45 CONTROL CIRCUITRY LOCKOUT – Auto-reset after 1 hour lockout due to:

- Flame sense circuit failure.

- Gas valve relay stuck open.

- Software check error.

Reset power to clear lockout. Replace control if status code repeats.

COMPONENT TEST

To initiate the component test sequence, shut “OFF” the room thermostat or disconnect the “R” thermostat lead. Reset power and then put setup switch

“SW1-6” in the ON position to start the component test sequence. Once initiated the furnace control will turn the inducer ON at high-heat speed. The

inducer motor will run for the entire test. The hot surface igniter and blower motor will be turned ON for 15 seconds each. When the blower is turned

OFF the inducer will be turned OFF. When the component test is completed one or more of the following codes will flash.

LED CODE DESCRIPTION

11 Indicates the blower motor tested OK. Visual check of inducer motor and hot surface igniter required.

25 SETUP ERROR – Same as code 25 above.

41 BLOWER MOTOR FAULT – Indicates blower motor failed test. Check blower, wiring, and furnace control.

42 INDUCER MOTOR FAULT – Indicates inducer motor failed test. Check inducer, wiring, and furnace control.

To repeat component test turn setup switch “SW1-6” OFF and then back ON. After component test is completed put setup switch “SW1-6” in the OFF

position and reconnect the “R” thermostat lead.

- 9 -

START HERE - If a problem exists, the service technician should always begin

troubleshooting here.

SPECIAL NOTE: ALL VOLTMETERS ARE NOT THE SAME - YOUR VOLTAGE READINGS WILL VARY. THIS APPLIES TO THE

ENTIRE CONTENT OF THIS TROUBLESHOOTING MANUAL. THEY ARE NOT ABSOLUTE VALUES. CORRECT 115-VAC VOLTAGE,

CURRENT, AND POWER MEASUREMENTS CANNOT BE TAKEN ON VARIABLE SPEED FURNACES UNLESS USING A TRUE RMS

METER.

STEP ACTION YES NO GO TO

1. Remove main furnace door first. DO NOT REMOVE BLOWER ACCESS PANEL! Record

status of AMBER LED. See Service/Status Code Instructions.

Is AMBER LED status light on?

2 19

2. Is the AMBER LED status light blinking rapidly without a pause? 3 4

3. Go to the page number indicated in the Index for RAPID FLASHING LED. INDEX

4. Is the AMBER LED status light blinking ON/OFF slowly with a combination of short and

long flashes?

5 7

5. Determine status code. The status code is a 2 digit number with the first digit determined by

the number of short flashes and the second digit by the number of long flashes.

6. Go to page number indicated in the Index for the section covering the status code. INDEX

7. To retrieve previous codes, disconnect the User Interface ABCD connector (if used) or the R

thermostat lead (if used) from the furnace control board and wait for the blower to turn off if it

is running. Put setup switch SW1-1 in the ON position and record the status codes listed in the

status code history. The status codes will flash in the order of occurrence. Read status codes

until an 11 code flashes. After the 11 code flashes the status codes will repeat.

8. Was there a previous status code other than code 11?

Note: Status codes are erased after 72 hours or can be manually erased by putting setup switch

SW1-1 in the ON position and jumpering R, W/W1, and Y/Y2 simultaneously until status

code 11 is flashed.

9 10

9. Go to page number indicated in the Index for the section covering the first previous status

code.

INDEX

10. Does the problem appear to be low cooling airflow? 11 12

11. Go to page number indicated in Index for the section covering IMPROPER COOLING

AIRFLOW.

INDEX

12. Set thermostat to call for heat and set the thermostat fan control to AUTO position if equipped. 13

13. Does the furnace respond to the call for heat? 14 28

14. Observe operation of furnace for 20 minutes or until AMBER LED status light starts blinking. 15

15. Does the AMBER LED status light blink ON/OFF slowly with a combination of short and

long flashes?

5 16

16. Is the temperature rise below the range specified on the rating plate when the unit is operating

in high heat?

Note: If the temperature rise is above the range specified on the rating plate refer to the Start-

Up and Adjustment section in the Installation, Start-Up, and Operating Instructions.

17 18

17. Go to page number indicated in Index for the section covering HIGH HEAT

TEMPERATURE RISE TOO LOW (COLD BLOW).

INDEX

18. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

19. Make sure power is being supplied to the furnace. 20

20. Check fuses, breakers, or manual disconnects to be sure they are correctly set. If not, reset

them and go back to step 1.

21. Remove blower access panel and depress door switch. Use a piece of tape to hold switch

closed.

22. Is 115-vac across L1 and L2? 24 23

23. Turn power off. Check continuity of power leads and door switch. If necessary repair power

leads and/or replace door switch.

24. Is 24-vac across SEC-1 and SEC-2? 25 26

25. Replace the variable speed furnace control. 18

- 10 -

STEP ACTION YES NO GO TO

26. Is 115-vac across the transformer leads? 27 25

27. Replace the transformer. 18

28. Is 24-vac across W/W1 and COM-24V on the variable speed furnace control?

You will not be able to check for voltage across W/W1 and C

OM-24V if the furnace is

connected to a User Interface at the ABCD connector. Go to step 29.

30 29

29. You have a defective thermostat, or a break in wiring between thermostat and furnace. Fix

problem.

30. Disconnect all thermostat leads from the thermostat terminal block and jumper R to W/W1.

Does the furnace respond to the call for heat?

31 25

31. You have an incompatible thermostat. Do any of the following:

1. Wire the thermostat C terminal to C

OM-24V.

2. Isolate the W/W1 input with a relay.

3. Install ballast resistor across W/W1 and C

OM-24V.

4. Replace the thermostat with a compatible model.

RAPID FLASHING AMBER LED - Indicates line voltage polarity is reversed, or the

transformers are out of phase in twinned units.

STEP ACTION YES NO GO TO

1. Is this furnace twinned with another furnace? 7 2

2. Remove blower access panel and depress door switch. Use a piece of tape to hold switch

closed.

3. Is 115-vac across NEUTRAL-L2 and chassis ground? 4 6

4. Line voltage polarity is reversed. Fix problem. 5

5. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

6. Replace the variable speed furnace control. 5

7. Remove blower access panels and depress door switch in each unit. Use tape to hold switches

closed.

8. Is the AMBER LED status light blinking rapidly in only one of the twinned units? 9 16

9. Are the fuses, breakers, or manual disconnects to the problem unit correctly set? 11 10

10. Fix problem. 5

11. Are the Auxiliary Limit switches properly set? 12 10

12. Do you have 115-vac across L1 and NEUTRAL-L2 in the problem unit? 13 15

13. Do you have 24-vac across SEC-1 and SEC-2 in the problem unit? 6 14

14. Replace the transformer. 5

15. Turn power off to both units. Check continuity of power leads and door switch in the problem

unit. If necessary repair power leads and/or replace door switch in the problem unit.

16. Check the furnace circuit breaker location in the service panel.

On single-phase (residential) systems, each furnace circuit breaker should be located directly

across from each other in service panel, or each furnace circuit breaker should be located on

the same side of service panel, but must skip 1 space to be connected to the same leg of the 1-

phase power supply.

On 3-phase (commercial) systems, each furnace circuit breaker should be located directly

across from each other in service panel, or each furnace circuit breaker should be located on

the same side of service panel, but must skip 2 spaces to be connected to the same leg of the 3-

phase power supply.

17. Check the 115-vac power lead connections at the variable speed furnace control of each

furnace. The BLACK lead goes to L1 and the WHITE lead goes to NEUTRAL-L2.

18. Check the 115-vac transformer lead connections at the variable speed furnace control of each

furnace. The BLACK lead goes to L1 and the WHITE lead goes to NEUTRAL-L2.

19. If the circuit breaker location and the 115-vac wiring is correct reverse the transformer

secondary lead connections SEC-1 and SEC-2 in the MAIN furnace.

- 11 -

IMPROPER COOLING AIR FLOW - Generally, this indicates the Y/Y2 thermostat lead is not

properly connected. If User Interface is connected to ABCD connector then the wrong size

outdoor unit could be configured in the User Interface.

STEP ACTION YES NO GO TO

1. Remove blower access panel and depress door switch. Use a piece of tape to hold switch

closed.

2. Set thermostat to call for cooling. If thermostat does not have G connection jumper across

thermostat terminals R and G.

3. Make sure thermostat fan control is in the AUTO position if equipped. 4

4. Do you have 24-vac across Y/Y2 and COM-24V on the variable speed furnace control? 8 5

5. You have a defective thermostat, or a break in the wiring between the thermostat and the

furnace, or the Y/Y2 thermostat terminal is not wired to the thermostat.

6. Fix the problem. 7

7. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

8. Are the air conditioning airflow select switches A/C set to the proper airflow as required by the

condensing unit? Typical airflow is based on 350 CFM/TON (See Table 2.)

10 9

9. Set the air conditioning airflow select switches A/C to the proper airflow as required by the

condensing unit. (See Table 2.)

10. Disconnect the G thermostat lead or jumper if used. 11

11. Does the blower motor turn off in 5 seconds when the G thermostat lead is disconnected?

Note: When using a Thermidistat the blower may change airflow when the G thermostat lead

is disconnected and a call to dehumidify is active.

12 13

12. Replace the variable speed furnace control. 7

13. Reconnect the G thermostat lead or jumper and observe operation of furnace in cooling mode

for 10 minutes.

14. Does the furnace operate properly in cooling mode? 15 16

15. - Check outdoor unit for correct suction pressure and verify charge.

- Check filter(s) and ductwork for restrictions.

- Check furnace coil.

INDEX

16. Does the AMBER LED abruptly shut off as the blower comes up to speed? 17 24

17. Do you have less than 17 vac between R and COM-24V on the variable speed furnace control? 18 24

18. Do you have less than 90 vac between L1 and NEUTRAL-L2 on the variable speed furnace

control?

19 20

19. Make sure the wire gage between main fuse box and furnace complies with wire size

specification in Installation, Start-Up, and Operating Instructions.

20. Disconnect the R thermostat lead. 21

21. Do you have less than 17 vac between R and COM-24V on the variable speed furnace control? 22 23

22. Replace transformer. 7

23. Check the thermostat wire gage between furnace and thermostat, and furnace and outdoor unit.

It is recommended that AWG No. 18 color-coded copper thermostat wire be used for lengths

up to 100 ft. For wire lengths over 100 ft, use AWG No. 16 wire.

24. Is Status Code 41 flashing? 25 26

25. Go to the page number indicated in the Index for Status Code 41. INDEX

26. - Check outdoor unit for correct suction pressure and verify charge.

- Check furnace coil.

27. Is a User Interface connected to the ABCD connector? 28 2

28. The wrong size outdoor unit may have been selected in the User Interface. You will need to

set the proper size of the outdoor unit in the User Interface. If set properly then the User

Interface may be reducing the airflow for dehumidification.

- 12 -

Table 2 – Cooling Tonnage vs. Airflow (CFM)

AIR CONDITIONING TONS

(12,000 BTU/HR)

AIRFLOW

(CFM)

040, 060, & 3T-

080 MODEL

5T-080 & 100

MODEL

120 MODEL

1-1/2

525 X

700 X X X

2-1/2

875 X X X

1050 X X X

3-1/2

1225 X X X

1400 X X

1750 X X

2100 X

HIGH HEAT TEMPERATURE RISE TOO LOW - Generally, this indicates the HI solenoid in gas

valve GV has failed or the furnace is extremely underfired.

STEP ACTION YES NO GO TO

1. Remove the blower access panel. Disconnect User Interface ABCD connector (if used) or the

R thermostat lead (if used) from the furnace control board. If setup switch SW1-2 is ON then

set it to OFF.

2. Depress the door switch. Use piece of tape to hold it closed. 3

3. Jumper R and W/W1 thermostat terminals. 4

4. When the furnace is running in low heat, clock the low heat gas rate. You have 16 minutes on

this first call for heat before unit switches to high heat. On propane installations check the

manifold pressure.

5. When the furnace is running in high heat, clock the high heat gas rate. On propane

installations check the manifold pressure.

6. Is the high heat rate approximately the same as the low heat rate? 7 11

7. Do you have 24 vac across gas valve terminals HI and COM-24V on 2-stage gas valve during

high heat?

10 8

8. You have an open wire or bad terminal on the BROWN wire from the high heat pressure

switch HPS to the gas valve GV. Repair it or replace the harness.

9. Go to the page number indicated in Index for the CLEANUP AND STARTUP

INSTRUCTIONS.

INDEX

10. Replace the gas valve. 9

11. Is the high heat rate within 2% of that specified on the rating plate? 13 12

525

700

875 1050

875

700 875

1050

1225

1400

1225

1750

1225

1750

2100

DEF.

040, 060, 3T-080

5T-080, 100

120

BASED ON 350 CFM/TON (SETUP SWITCH SW1-5 OFF)

SETUP SWITCH SW3 POSITIONS

MODEL

SIZE

600

800

1000 1200

1000

800 1000

1200

1400

1600

1400

2000

1400

2000

2100

DEF.

040, 060, 3T-080

5T-080, 100

120

BASED ON 400 CFM/TON (SETUP SWITCH SW1-5 ON)

1. DEFAULT A/C AIRFLOW WHEN A/C SWITCHES ARE IN OFF POSITION

2. DEFAULT CONT. FAN AIRFLOW WHEN CF SWITCHES ARE IN OFF POSITION

3. SWITCH POSITIONS ARE ALSO SHOWN ON FURNACE WIRING DIAGRAM

SETUP SWITCH SW3 POSITIONS

MODEL

SIZE

AIR CONDITIONING (A/C) OR CONTINUOUS-FAN (CF)

AIRFLOW SELECTION CHART

- 13 -

STEP ACTION YES NO GO TO

12. Ensure the gas inlet pressure and burner orifice are correct. Then adjust the gas valve to the

proper rate. If it cannot be adjusted to the proper rate, replace the gas valve.

13. Is outdoor condensing unit operating during heating cycle? 16 14

14. Check temperature rise and external static pressure with blower access panel in place.

Temperature rise should be mid range or higher than midpoint of range stated on furnace rating

plate. External static pressure must not exceed .7 in.w.c. If return temperature is below 60

deg. F condensation may form on heat exchangers. If left uncorrected failure will result.

15. Check return air ducts in unheated spaces for leaks. 9

16. Fix problem. 9

Status Code 11

NO PREVIOUS CODE - Stored status codes are erased after 72 hours or can be cleared by jumpering R, W/W1, and Y/Y2

thermostat leads while setup switch SW1-1 is ON. Run system through a heating or cooling cycle to check system.

This usually indicates one of the following:

- The status history has been cleared and setup switch SW1-1 is in the ON position.

- Component test was successfully completed and setup switch SW1-6 is in the ON position.

STEP ACTION YES NO GO TO

1. Remove the blower access panel, depress the door switch. Use piece of tape to hold it closed. 2

2. Is setup switch SW1-1 in the ON position. 3 5

3. Put setup switch SW1-1 in the OFF position. 4

4. Go to the page number indicated in Index for the CLEANUP AND STARTUP

INSTRUCTIONS.

INDEX

5. Is setup switch SW1-6 in the ON position. 6 7

6. Put setup switch SW1-6 in the OFF position. 4

7. Jiggle setup switches SW1-1 and SW1-6 back and forth. If status code 11 continues to flash

replace the variable speed furnace control

Status Code 12

BLOWER ON AFTER POWER UP - Blower will run for 90 seconds when furnace power is interrupted and later restored during

a call for heat (R-W/W1 closed) or if the call for heat is interrupted (R-W/W1 opens) during the blower on-delay period. If this

status code repeats every couple of minutes it is probably caused by a direct short in the pressure switch circuits, gas valve

GV, wiring to gas valve GV, or humidifier coil.

STEP ACTION YES NO GO TO

1. Remove the blower access panel and disconnect User Interface ABCD connector

(if used) or the R thermostat lead (if used) from the furnace control board.

2. Depress the door switch. Use piece of tape to hold it closed. 3

3. Jumper R and W/W1 thermostat terminals. 4

4. Does the furnace keep repeating the following cycle?

Induced draft motor IDM runs, induced draft motor IDM stops, blower motor

BLWM runs for 90 seconds while AMBER LED status light flashes status code 12.

5 20

5. Do you have less than 17-vac across R and COM-24V on the variable speed furnace

control?

6 14

6. Do you have less than 90-vac across L1 and NEUTRAL-L2 on the variable speed

furnace control?

7 10

7. Make sure wire gage between main fuse box and furnace complies with wire size

specification in Installation, Start-Up, and Operating Instructions.

8. Fix problem. 9

9. Go to the page number indicated in Index for the CLEANUP AND STARTUP

INSTRUCTIONS.

INDEX

- 14 -

STEP ACTION YES NO GO TO

10. Disconnect the R thermostat lead. 11

11. Do you have less than 19-vac across R and COM-24V on the variable speed furnace control? 12 13

12. Replace transformer. 9

13. The thermostat and/or thermostat wires are loading down the transformer. Replace the

thermostat or repair thermostat wires.

14. Does the hot surface ignitor HSI come on during the cycle? 15 19

15. Disconnect the humidifier lead from HUM terminal on variable speed furnace control. 16

16. Does the furnace still alternately cycle induced draft motor IDM and blower motor BLWM as

described in Step 4.

18 17

17. There is a direct short in wiring to humidifier solenoid coil, diode bridge(if used), or humidifier

solenoid coil.

18. There is a short in the gas valve GV or wiring to gas valve GV. Refer to Appendix E to check

gas valve GV.

19. There is a direct short in the ORANGE wire from the low heat pressure switch LPS. 8

20. While the unit is operating in low heat jumper R and W2 thermostat terminals. 21

21. Does the furnace abruptly shut down with no inducer post purge and then run blower motor

BLWM for 90 seconds while AMBER LED status light flashes status code 12.

22 26

22. Disconnect BROWN wire to gas valve GV. 23

23. Does the furnace still abruptly shut down as described in Step 21. 25 24

24. Replace gas valve. 9

25. There is a direct short to ground in the GRAY or BROWN wires connected to the high heat

pressure switch HPS.

26. Power to the furnace was probably interrupted or line voltage was too low during a call for

heat. This is normal operation. Go to the page number indicated in Index for the CLEANUP

AND STARTUP INSTRUCTIONS.

INDEX

Status Code 13

LIMIT CIRCUIT LOCKOUT – Lockout occurs if the limit or flame rollout switch is open longer than 3 minutes or 10 successive

limit trips occurred during high-heat. The variable speed furnace control will auto-reset in 3 hours. Flame roll-out switch FRS

requires manual-reset.

STEP ACTION YES NO GO TO

1. Remove the blower access panel. Disconnect User Interface ABCD connector (if used) or the

R thermostat lead (if used) from the furnace control board.

2. Depress the door switch. Use piece of tape to hold it closed. 3

3. Does status code 33 flash? 11 4

4. Does a different status code flash? 5 6

5. Go to page number indicated in the Index for the section covering the status code. INDEX

6. Jumper R and W/W1 thermostat terminals. 7

7. Observe the furnace operation for 25 minutes or until status code starts flashing. 8

8. Does status code 33 flash? 26 9

9. Does a different status code flash? 5 10

10. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

11. Is 24-vac across connector terminal PL1-6 and COM-24V on variable speed furnace control? 13 12

12. Replace the variable speed furnace control. 10

13. Is 24-vac across connector terminal PL1-8 and COM-24V on variable speed furnace control? 12 14

14. Turn power off. 15

15. Do you have continuity across limit switch LS? 17 16

16. Replace limit switch LS. 10

17. Do you have continuity across the flame rollout switch FRS? 25 18

18. Can flame rollout switch FRS be reset? 20 19

- 15 -

STEP ACTION YES NO GO TO

19. Replace flame rollout switch FRS. 10

20. Reset flame rollout switch FRS, turn power on, and observe furnace operation for (2) 15

minute cycles.

21. Does the flame rollout switch FRS trip again? 23 22

22. Does a different status code flash? 5 10

23. You have inadequate combustion-air supply. This may be caused by:

- Reversed vent and combustion-air pipes.

- Poor burner, manifold, or orifice alignment.

- Blocked heat exchanger.

- Leak somewhere between primary and secondary heat exchangers.

- Leak in secondary heat exchanger.

24. Fix problem 10

25. You have an open RED wire or bad terminal in limit circuit. Repair wire or replace harness. 10

26. Does furnace have the proper limit switch, limit shield, blower baffle (if used), and rear air

baffle (if used)? If so, are the limit switch, limit shield, and heat exchangers properly aligned?

27 24

27. Remove tape from door switch, turn power off at main disconnect, and remove jumper across

R and W/W1.

28. Is blower wheel firmly mounted on motor shaft? 29 24

29. Does the model plug PL4 match the part number specified on the Model Plug Chart in upper

left hand corner of wiring schematic?

31 30

30. Replace model plug. 10

31. Lockout may have been caused by excessive return-air restriction. Check all dampers, filters,

and return-air grilles for blockage. Add more return-air openings if necessary. Use Appendix

D to evaluate external static pressure. Reference status code 33 for additional troubleshooting

steps.

Status Code 14

IGNITION LOCKOUT - This status code indicates the furnace failed to ignite gas and/or prove flame in 4 attempts. The variable

speed furnace control will auto-reset in 3 hours. If the inducer motor is not running during lockout refer to status code 34.

If the inducer motor is running at full speed during lockout this indicates that flame sense was lost 3 times within 60 minutes of

cumulative gas valve operating time after the gas valve was already ON for 70 seconds. It is usually caused by flame rollout

that causes loss of flame sense before the flame rollout switch can trip.

Status Code 15

BLOWER MOTOR LOCKOUT - This status code indicates the blower failed to reach 250 RPM or the blower failed to

communicate to the variable speed furnace control within 30 seconds after being turned ON in two successive heating cycles.

Control will auto reset after 3 hours. Refer to status code 41.

Status Code 21

GAS HEATING LOCKOUT - This status code indicates the main gas valve relay MGVR on the variable speed furnace control is

stuck closed or there is a miswire/short to gas valve wiring. Make sure the BLUE wire goes to the gas valve M terminal and the

GREEN/YELLOW wire goes to the gas valve C terminal. The variable speed furnace control will NOT auto-reset.

STEP ACTION YES NO GO TO

1. Turn power off and disconnect User Interface ABCD connector (if used) or the R thermostat

lead (if used) from the furnace control board. Then turn power back on.

2. Does status code 21 flash? 3 6

3. There is a miswire or short to gas valve wiring. 4

4. Fix problem 5

5. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

6. Does a different status code flash? 7 8

- 16 -

STEP ACTION YES NO GO TO

7. Go to page number indicated in the Index for the section covering the status code. INDEX

8. Remove blower access panel and depress door switch. Use a piece of tape to hold switch

closed.

9. Jumper R and W/W1 thermostat terminals. 10

10. Does status code 21 start flashing when the low heat pressure switch LPS makes? 11 12

11. Replace the variable speed furnace control. 5

12. Does a different status code flash? 7 13

13. Disconnect the jumper wire across R and W/W1 thermostat terminals and wait until the blower

stops.

14. Jumper R, W/W1, and W2 thermostat terminals on the variable speed furnace control. 15

15. Does status code 21 start flashing when the high heat pressure switch HPS makes? 16 17

16. The BLUE and GREEN wires to gas valve GV are reversed. 4

17. Cycle the furnace several times to check for intermittent operation. 18

18. Does status code 21 ever flash? 11 19

19. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. If

the problem persists on an intermittent basis, replace the variable speed furnace control. If

problem still persists on an intermittent basis after replacing the variable speed furnace control,

contact your distributor.

INDEX

Status Code 22

ABNORMAL FLAME-PROVING SIGNAL - This status code indicates the flame signal was sensed while gas valve GV was de-

energized. The inducer will run until the fault is cleared.

STEP ACTION YES NO GO TO

1. Turn off gas to the furnace by shutting off the external manual shut-off valve. 2

2. Does status code 22 stop flashing? 3 4

3. Replace the gas valve. 8

4. Disconnect wire from the flame-proving sensor electrode FSE. 8

5. Does status code 22 stop flashing? 6 7

6. Clean flame sensor with fine steel wool. Inspect burner box assembly and remove any carbon

deposits near the flame sensor opening.

7. Replace the variable speed furnace control. 8

8. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

Status Code 23

PRESSURE SWITCH DID NOT OPEN - This status code indicates the low or high heat pressure switch LPS or HPS is made

when a call for heat is initiated. The variable speed furnace control will flash status code 23 until the switch opens, then cycle

begins.

STEP ACTION YES NO GO TO

1. Turn power off, remove blower access panel, and disconnect User Interface ABCD connector

(if used) or the R thermostat lead (if used) from the furnace control board.

2. Turn power on and depress door switch. Use a piece of tape to hold switch closed. 3

3. Jumper R and W/W1 thermostat terminals. 4

4. Does status code 23 flash? 8 5

5. Does a different status code flash? 6 7

6. Go to page number indicated in the Index for the section covering the status code. INDEX

7. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

8. Is the inducer motor ON? 21 9

9. Is 24-vac across ORANGE wire on the low heat pressure switch LPS and COM-24V on

variable speed furnace control?

16 10

10. Is 24-vac across connector terminal PL1-4 and COM-24V on variable speed furnace control? 11 13

11. The main harness is miswired. 7

12. Rewire low heat pressure switch LPS per the wiring diagram. 7

13. Is 24-vac across BROWN wire on the high heat pressure switch HPS and COM-24V on

variable speed furnace control?

18 14

14. Is 24-vac across connector terminal PL1-3 and COM-24V on variable speed furnace control? 11 15

- 17 -

STEP ACTION YES NO GO TO

15. Replace variable speed furnace control. 7

16. Is the low heat pressure switch LPS wired correctly? 17 12

17. Replace the pressure switch assembly. 7

18. Is the high heat pressure switch HPS wired correctly? 20 19

19. Rewire high heat pressure switch HPS per wiring diagram. 7

20. Replace the pressure switch assembly and replace the variable speed furnace control. 7

21. Check the inducer PWM line. To do this disconnect PL11 from the inducer motor and connect

a DC voltmeter across terminals PL11-2 BROWN (+) and PL11-10 YELLOW (-) then run

COMPONENT TEST by turning setup switch SW1-6 ON. Does voltage across PL11-2 and

PL11-10 change between states as shown below?

- State 1 – OFF (1.0 – 4.0 vdc)

- State 2 – MED (7.0 – 10.0 vdc)

22 15

22. Replace inducer motor or inducer motor assembly. 7

Status Code 24

SECONDARY VOLTAGE FUSE IS OPEN - Indicates fuse is open and there is a short in low-voltage wiring.

STEP ACTION YES NO GO TO

1. Turn power off and remove the blower access panel. 2

2. Is secondary voltage fuse blown? Check continuity to make sure. 5 3

3. Replace variable speed furnace control. 4

4. Replace secondary voltage fuse if necessary then go to page number indicated in Index for

CLEANUP AND START-UP INSTRUCTIONS.

INDEX

5. Disconnect User Interface ABCD connector (if used), or all thermostat leads (if used) from the

variable speed furnace control (including all wires connected to the HUM terminal) and

replace secondary voltage fuse.

6. Turn power on and depress door switch. Use a piece of tape to hold switch closed. 7

7. Does status code 24 flash? 8 12

8. Turn power off and disconnect PL1 from variable speed furnace control. 9

9. Do you have continuity between either RED wire connected to the limit circuit and chassis

ground?

10 3

10. You have a short circuit in the limit switch circuit. This includes limit switch LS, and flame

roll-out switch FRS.

11. Fix problem. 4

12. Disconnect the pressure tube from the collector box and jumper R and W/W1 thermostat

terminals.

13. Does status code 24 begin flashing when W/W1 is energized? 14 21

14. Turn power off and disconnect PL1 from variable speed furnace control. 15

15. Do you have continuity between the YELLOW wire connected to the low heat pressure switch

LPS and chassis ground?

16 3

16. You have a short circuit in the low heat pressure switch circuit. 11

17. Does status code 24 begin flashing when the HUM terminal is energized?

Note: On the variable speed furnace control the HUM terminal is energized when the blower

turns ON.

3 18

18. Disconnect jumper wire across R and W/W1 thermostat terminals and wait until inducer stops. 19

19. Disconnect the pressure tube from the collector box and jumper R, W/W1, and W2 thermostat

terminals.

20. Does status code 24 begin flashing when W/W1 is energized? 34 37

21. Reconnect the pressure tube from the pressure switch assembly back to the collector box. 22

22. Does status code 24 begin flashing when the low heat pressure switch LPS is energized? 23 26

23. Turn power off and disconnect PL1 from variable speed furnace control. 24

24. Do you have continuity between the ORANGE wire connected to the low heat pressure switch

LPS and chassis ground?

25 3

25. The ORANGE wire from low heat pressure switch LPS is shorting to ground. Replace or

repair it.

26. Does status code 24 begin flashing when the gas valve GV is energized? 27 17

- 18 -

STEP ACTION YES NO GO TO

27. Disconnect jumper wire across R and W/W1 thermostat terminals and replace secondary

voltage fuse.

28. Disconnect BLUE wire to gas valve GV and jumper R and W/W1 thermostat terminals. 29

29. Does status code 34 flash? If not, status code 24 should occur when BLUE wire is energized. 33 30

30. Turn power off and disconnect PL1 from variable speed furnace control. 31

31. Do you have continuity between the BLUE wire and chassis ground? 32 3

32. The BLUE wire to gas valve GV is shorting to ground. Replace or repair it. 11

33. Replace gas valve GV. 4

34. Turn power off and disconnect PL1 from variable speed furnace control. 35

35. Do you have continuity between the GRAY wire connected to the high heat pressure switch

HPS and chassis ground?

36 3

36. You have a short circuit in the high heat pressure switch circuit. 11

37. Reconnect the pressure tube from the pressure switch assembly back to the collector box. 38

38. Does status code 24 begin flashing when the high heat pressure switch HPS is energized? 39 56

39. Disconnect jumper wire across R, W/W1, and W2 thermostat terminals and replace secondary

voltage fuse.

40. Disconnect BROWN wire to gas valve GV and jumper R, W/W1, and W2 thermostat

terminals.

41. Does status code 24 begin flashing when the high heat pressure switch HPS is energized? 42 33

42. Turn power off and disconnect PL1 from variable speed furnace control. 43

43. Do you have continuity between the BROWN wire and chassis ground? 44 3

44. The BROWN wire to high heat pressure switch HPS and gas valve GV is shorting to ground.

Replace or repair it.

45. Disconnect jumper wire across R, W/W1, and W2 thermostat terminals and wait until blower

stops.

46. Jumper R, G, and Y/Y2 thermostat terminals. 47

47. Does status code 24 begin flashing when G and Y/Y2 are energized? 3 48

48. Reconnect User Interface ABCD connector (if used) or all thermostat leads (if used) to the

variable speed furnace control. Do not reconnect the humidifier lead to HUM terminal.

Operate the furnace in heating and cooling mode from thermostat.

49. Does status code 24 occur during heating cycle? 50 51

50. You have a defective thermostat or a short circuit in the wiring between thermostat and

furnace. If the furnace is twinned, also check the twinning kit relay TKR.

51. Does status code 24 occur during cooling cycle? 52 53

52. You have a defective thermostat or a short circuit in the wiring between thermostat and

outdoor unit, or a short circuit in the outdoor unit contactor or reversing valve(heat pump

only).

53. Does problem usually occur in cooling mode? 54 55

54. Check outdoor unit contactor. Failure to pull in can cause excessive current draw on low-

voltage circuit. This can be an intermittent problem.

55. Reconnect humidifier and check for excessive current draw when the blower turns ON. If

current draw is excessive check wiring to humidifier solenoid, diode bridge(if used), and

humidifier solenoid.

56. Continue to observe the furnace operation for 10 minutes. 57

57. Does status code 24 flash after the blower comes on? 58 59

58. The insulation is loose and has shorted against the limit switch(es). 11

59. Check for loose or torn insulation because it can cause intermittent occurrences of status code

24.

- 19 -

Status Code 25

MODEL SELECTION OR SETUP ERROR – If status code 25 only flashes 4 times on power-up the variable speed furnace

control is missing its model plug (PL4) and is defaulting to the model selection stored in memory.

If status code 25 flashes continuously it could indicate any of the following:

1. Model plug (PL4) is missing and there is no valid model stored in permanent memory. This will happen if you forget to

install the model plug (PL4) on a service replacement board.

2. Thermostat call with SW1-1 ON.

3. Thermostat call with SW1-6 ON.

4. SW1-1 and SW1-6 both ON together.

5. Two different furnace models twinned.

6. Board does not recognize 355BAV model plugs HK70EZ057 – 061. Furnace board date code 4106 or later required.

STEP ACTION YES NO GO TO

1. Turn power off, remove the blower access panel, and disconnect User Interface ABCD

connector (if used) or the R thermostat lead (if used) from the furnace control board.

2. Turn power on and depress door switch. Use a piece of tape to hold switch closed. 3

3. Does status code 25 flash only 4 times on power-up? 4 6

4. The model plug is missing or invalid but the control will default to the model stored in

memory. The furnace will operate properly as if the model plug was installed. If you have the

APM program you can confirm the setting in memory.

5. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

6. Is setup switch SW1-1 in the ON position? 7 8

7. Put setup switch SW1-1 in the OFF position. 5

8. Is setup switch SW1-6 in the ON position? 9 10

9. Put setup switch SW1-6 in the OFF position. 5

10. Is this a new service replacement control? 19 13

11. You need to remove the model plug PL4 from the old control and install it on the new

replacement control. Once you install the model plug the power to the furnace needs to be

reset because the model plug is only read on power-up.

12. If the model plug is not available from the old control, reference the model plug chart on the

wiring schematic for the correct part number. If absolutely necessary you can install two

resistors into the PL4 connection on the control board. R1 goes across the middle 2 pins and

R2 goes across the outer 2 pins. Reference the model plug chart on the schematic for the

correct resistance values. Resistors can be purchased at a nearby Radio Shack. The resistors

need to be within 10% of the stated value. Check with an ohm meter before installing.

13. Is this furnace twinned with another furnace? 14 17

14. Is the MAIN furnace flashing the status code? 15 17

15. Do the furnaces have the same model number on the rating plate? 18 16

16. Replace one of the furnaces because you cannot twin different size furnaces. 5

17. Replace the variable speed furnace control. 5

18. One of the model plugs is bad. Ohm out each one and replace the one that does not match the

model plug chart on the wiring schematic.

19. Is the model plug PL4 from the old control installed? 20 11

20. On 355BAV furnaces make sure you have installed a furnace control date code 4106 or later.

The date code is the last 4 digits printed after the board part number in the WHITE box near

the L2 terminals on the right side of the furnace control. Reference Figure 1 in Appendix A for

the location of the board date code.

Status Code 31

HIGH-HEAT PRESSURE SWITCH OR RELAY DID NOT CLOSE OR REOPENED - This status code can occur under the

scenarios shown below. Keep in mind that whenever the variable speed furnace control shuts unit down, gas remains off or

shuts off immediately, inducer continues running for 15 seconds, and if the blower is running, it remains running at low heat

airflow or reduces to low heat airflow for the selected off-delay. A miswired gas valve can cause this problem so make sure the

BLUE wire goes to the gas valve M terminal and the GREEN/YELLOW wire goes to the gas valve C terminal.

- LOW HEAT

1. PREPURGE OR STEADY-STATE - If the high heat pressure switch input turns ON the variable speed begins flashing status code 31 and

transitions to high heat. After the call for heat is satisfied and the blower off-delay is completed the control will stop displaying status code

31.

- 20 -

- HIGH HEAT

1. PREPURGE - If the high heat pressure switch HPS does not make within 45 seconds after the low-heat pressure switch LPS made the

variable speed begins flashing status code 31, shuts unit down, waits 2 minutes, stops flashing status code 31, and restarts heating cycle.

If high heat pressure switch HPS opens before ignition, the variable speed starts flashing status code 31 and ramps inducer RPM up until the

high heat pressure switch HPS remakes. When the high heat pressure switch HPS remakes the variable speed stops flashing status code 31

and continues heating cycle. If high heat pressure switch HPS does not remake within 45 sec after opening, the variable speed continues

flashing status code 31, shuts unit down, waits 2 minutes, stops flashing status code 31, and restarts heating cycle.

2. LOW HEAT TO HIGH HEAT TRANSITION - If the high heat pressure switch HPS fails to make within 45 seconds after high heat was

requested the variable speed furnace control shuts unit down and begins flashing status code 31. After the blower off-delay is completed the

variable speed will stop displaying status code 31 and if there is a call for heat, begin a new heating cycle. This new heating cycle will be

restricted to high heat.

3. STEADY-STATE - If the high heat pressure switch HPS opens the variable speed starts flashing status code 31 and ramps inducer RPM up

until the high heat pressure switch HPS remakes. When the high heat pressure switch HPS remakes the variable speed stops flashing status

code 31 and continues heating cycle. If high heat pressure switch HPS does not remake within 45 sec after opening, the variable speed shuts

the unit down and continues flashing status code 31. After the blower off-delay is completed the variable speed will stop displaying status

code 31 and if there is a call for heat, begin a new heating cycle. This new heating cycle will be restricted to high heat.

4. HIGH HEAT TO LOW HEAT TRANSITION – When using a 2-stage thermostat and W2 is de-energized, the high heat pressure switch

HPS must open within 5 seconds. If the high heat pressure switch HPS does not open within 5 seconds after W2 is de-energized, the variable

speed switches back to high heat and starts flashing status code 31. After the call for heat is satisfied and the blower off-delay is completed

the variable speed will stop displaying status code 31.

STEP ACTION YES NO GO TO

1. Turn power off, remove blower access panel, and disconnect User Interface ABCD connector

(if used) or the R thermostat lead (if used) from the furnace control board.

2. Turn power on and depress door switch. Use a piece of tape to hold switch closed. 3

3. Jumper R, W/W1, and W2 thermostat terminals. 4

4. Wait 90 seconds before proceeding to the next step. 5

5. Does status code 31 flash? 9 6

6. Does a different status code flash? 7 34

7. Go to page number indicated in the Index for the section covering the status code. INDEX

8. Go to page number indicated in Index for CLEANUP AND START-UP INSTRUCTIONS. INDEX

9. Is 24-vac across GRAY wire on the high heat pressure switch HPS and COM-24V on variable

speed furnace control?

15 10

10. Is 24-vac across connector terminal PL1-12 and COM-24V on variable speed furnace control? 11 13

11. You have an open wire or bad terminal on the GRAY wire from the variable speed furnace

control to the high heat pressure switch HPS.

12. Repair or replace the main wire harness. 8

13. Replace the variable speed furnace control. 8

14. The problem is caused by reversed vent and combustion-air pipes or some other moist air

entering combustion-air pipe.

15. Does the high heat pressure switch HPS make, then break several times at start of cycle before

faulting out?

16 17

16. The problem is either a sag in vent pipe or a clogged drain trap or line. Also check for

improperly plumbed drainage tubing within furnace.

17. Is 24-vac across BROWN wire on the high heat pressure switch HPS and COM-24V on

variable speed furnace control?

18 20

18. Is 24-vac across connector terminal PL1-3 and COM-24V on variable speed furnace control? 13 19

19. You have an open wire or bad terminal on the BROWN wire from the high heat pressure

switch HPS to the variable speed furnace control.

20. Turn power off and disconnect jumper wire across R, W/W1, and W2 thermostat terminals. 21

21. Connect 1 side of slope manometer with a tee to collector box pressure tap. Connect other side

with a tee to gas valve pressure fitting. Refer to pressure check diagram in Appendix C.

22. Turn power on and jumper R, W/W1, and W2 thermostat terminals. 23

23. Do you have atleast 1.90 in. wc pressure drop across heat exchangers when status code 31

flashes?

24 25

24. Replace the pressure switch assembly. 8

25. Is inducer motor rotating in direction indicated on inducer housing? 27 26

26. Replace inducer motor or inducer motor assembly. 8

27. Turn power off. 28

Page is loading ...

Bryant 355AAV EVOLUTION Troubleshooting guide

Brand: Bryant

Model: 355AAV EVOLUTION

Category: Water heaters & boilers

Type: Troubleshooting guide

This manual is also suitable for

Download PDF

report

Bryant 355AAV EVOLUTION Troubleshooting guide

This manual is also suitable for

Bryant 355AAV EVOLUTION Troubleshooting guide

Related papers

Other documents