Dual XD1225 User manual

Brand: Dual

Model: XD1225

Category: Car media receivers

Type: User manual

Dual XD1225: Enjoy your favorite tunes with versatile playback options, enhanced audio customization, and convenient charging capabilities. Its detachable faceplate provides security, while the auxiliary input and USB charging port offer connectivity for various devices. Customize your listening experience with adjustable bass, treble, balance, and fader settings. Store up to 18 FM and 12 AM stations for easy access.

AM/FM/CD Receiver with Auxiliary Input, USB Charging Port and

Detachable Face

XD1225

Charge Port

INSTALLATION/OWNER'S MANUAL

Preparation

TYPICAL MOUNTING METHOD

XD1225 INSTALLATION

Please read entire manual before installation.

Before You Start

•Disconnectnegativebatteryterminal.Consultaqualifiedtechnicianforinstructions.

•Avoidinstallingtheunitwhereitwouldbesubjecttohightemperatures,suchasfrom

directsunlight,orwhereitwouldbesubjecttodust,dirtorexcessivevibration.

Getting Started

•Remove2transitscrewslocatedontopoftheunit.

•Insertthesuppliedkeysintotheslotsasshown,andslidetheunitoutofthemounting

sleeve.

•Installmountingsleeveintoopening,bendingtabstosecure.

•Connectwiringharnessandantenna.Consultaqualifiedtechnicianifyouareunsure.

•Certainvehiclesmayrequireaninstallationkitand/orwiringharnessadapter(sold

separately).

•Testforcorrectoperationandslideinto

mounting sleeve to secure.

•Snaptrimringintoplace.

Rear Preamp Output

Connect to amplifier RCA input

Antenna Connector

RCA Cable

(sold separately)

AMP

BLUE

BLACK

RED

YELLOW

Remote Turn-On

Connect to amplifier or power

antenna. Insulate wire if not used.

Ground

Connect to vehicle

chassis ground.

Accessory

Connect to ignition

circuit or switched 12 volt source.

Memory

Connect to battery

circuit or constant 12 volt source.

Right Front

Gray/Black (-)

Gray (+)

Left Front

White/Black (-)

White (+)

Right Rear

Violet/Black (-)

Violet (+)

Left Rear

Green/Black (-)

Green (+)

5 AMP

AGC Fuse

Wiring Diagram

FUSE

When replacing the fuse,

makesurenewfuseisthe

correct type and amperage.

Using an incorrect fuse

could damage the radio.

TheXD1225usesone5amp

AGC fuse located in-line.

* Caution-Donotattachanyspeakerleadstogroundasseveredamagewilloccur.

XD1225 INSTALLATION

Control Locations

Release

Mode / Power

Volume Knob

Display

Audio / Menu

Eject

USB Charging Port

Auxiliary Input

Preset 6

Preset5

Preset 4 / Play / Pause

Preset 3 / Intro

Preset 2 / Random

Preset1/Repeat

Band

Tune/TrackUp

Tune/TrackDown

1 2 3

XD1225 OPERATION

TheXD1225hasaneasy-to-useinterfacethatprovidesarewardingexperience,as

wellassupportforyourfavoritetunes.AudioCD-RandCD-RWdiscplaybackensures

compatibility with your music collection, and the RCA preamp output provides the right

connections to expand your system. From its front panel auxiliary input for connecting your

MP3 player, to the detachable face for security assurance, this head unit has you covered.

91011121314151617

General Operation

Press RELEASE and pull away from the left side to remove.

Tore-install,insertrightsideoffaceplatefirstthenpushleft

side to secure.

Removetrimringandinstallsupplied#1x7/32”Phillipshead

screw through left side of mounting frame into faceplate.

Press to turn the unit on. Inserting a CD will turn the unit

on automatically. Press and hold for three seconds to turn

the unit off.

Press MODE to select between AM/FM, CD or auxiliary input.

Modes of operation are indicated in the display.

Inserta3.5mmconnectorinthefrontpanelAUXport.

Connecttheotherendofthe3.5mmconnectortothe

headphone output of an audio device, MP3 player, etc. Press

MODEtoselectAUXmode.

Adjustvolumeusingthe rotary encoder(00-46).

Theradiofrequency(tunermode)andCDtrack/elapsedtime

(CDplayermode)willbeshownbydefault.PressDISP to

displaytheclock,andpressDISP again to return to default

display.

Press and hold DISPfor2seconds,theclockwillbeginto

flash. Press TRACK

toadjustthehoursandTRACK

toadjusttheminutes.PressDISPorwait5secondstosave

theclocksettings.

Theclockwilldisplay12-hourAM/PMtimeinUSAfrequency

spacingmode(PM10:00).InEuropeanfrequencyspacing

mode,theclockwilldisplay24-hourtime(22:00).

Press and hold for more than 2 seconds to RESET the unit

uponinitialinstallation.TheRESET button is located behind

the faceplate.

Faceplate Removal

Semi-permanent Faceplate

Installation

Power On/Off

Mode

Auxiliary Input

Volume

Display

Set the Clock

12/24-hour Clock

Reset

XD1225 OPERATION

Insert the USB connector of a battery powered USB device

into the USB charging port on the front panel, which

provides5voltsDCand1.0amps.TheUSBdevicewill

immediately begin charging.

Note: TheUSBchargingportmaynotbecompatiblewith

everydeviceduetodifferencesinpowerrequirements.

Note:ThisUSBportprovidespoweronly,andwillnot

playbackmusicfromaUSBdevice.

Press AUDIOtoselectbetweenVolume(default),Bass,

Treble,Balance,FaderandEQ.

USB Charging Port

Audio

BASS VOLUME TREBLE BALANCE FADER

XD1225 OPERATION

Menu Function Options Action

Loudness

Curve

LOUD OFF Disables the loudness function.

LOUD ON

Enables the loudness function. Activating this feature

willenhancethebassandtreblefrequencieswhen

listening to music at low volumes.

Tuner

Frequency

Spacing

FRE USA

Programs the unit to USA tuner spacing.

(200kHzforFMand10kHzforAM).(Tuner mode only)

FRE EU

Programs the unit to European tuner spacing.

(50kHzforFMand9kHzforAM).(Tuner mode only)

Local/Distance

Tuning

LOC OFF Activates distance tuning.

LOC ON Activates local tuning for strong station reception only.

Clock

Display

CLOC ON

Programsunittodisplaytheclockwhenthepoweris

off.

CLOC OFF

Programsunittonotdisplaytheclockwhenthepower

is off.

Beep

Confirmation

BEEP OFF Disables the confirmation beep.

BEEP ON Enables the confirmation beep.

General Operation

Press and hold AUDIO/MENU for more than 3 seconds to

access the setup menu, then press AUDIO/MENU to cycle

through menu options. When desired option appears in the

display, rotate the volume knobleft/righttoadjustoractivate

the desired function.

Setup Menu

Audio Operation

Press AUDIO until BAS appears

Rotate the volume knobleft/righttoadjust

(-6minimum/6maximum)

Press AUDIOuntilTREappears

Rotate the volume knobleft/righttoadjust

(-6minimum/6maximum)

Press AUDIO until BAL appears

Rotate the volume knobleft/righttoadjust

(LF12-RT12)"BALL=R"representsequalbalance.

Press AUDIO until FAD appears

Rotate the volume knobleft/righttoadjust

(FR12-RR12)"FADR=F"representsequalbalance.

Press AUDIOuntilEQappears.Rotatevolumeknobleft/

righttoadjustbetweenCLS,POP,ROCandOFF(default)

equalizationcurves.AnyadjustmenttotheBassorTreble

settingsautomaticallycancelsthecurrentEQcurve.

Press TUNE

or TUNE

for more than 2 seconds to

seektothenextstrongstation.

Press TUNE

or TUNE

momentarily to change the

radiofrequencyupordownonestepatatime.Pressand

holdtoadvancequickly.

Press BAND for more than 2 seconds to select mono or

stereo(default)receptionofthebroadcastsignal.

Press BANDtoselectbetweenFM1,FM2,FM3andAM1,AM2

bands.

Upto18FMstationsand12AMstationscanbestored.

Tostoreastation,selectthedesiredbandandstation.

Press and hold the desired preset button for more than 2

seconds. When stored, the preset number will appear in the

display.Thestationcanberecalledanytimebypressingthe

corresponding preset button.

Bass

Treble

Balance

Fader

Preset EQ Curves

Seek Tuning

Manual Tuning

FM Stereo/Mono

Band

Storing and Recalling

Station Presets

XD1225 OPERATION

Tuner Operation

CD Player Operation

Withthelabelfacingup,insertastandardsizeCDintothe

CDslot.TheCDwillautomaticallybeginplayback.

Press the EJECTbuttontostopandejecttheCD.

Theunitwillchangetotunermode.

Press TRACK

toskiptothebeginningofthenexttrack.

Press TRACK

to return to the beginning of the current

track.PressingTRACK

againskipstothebeginningof

theprevioustrack.

Press and hold TRACK

or TRACK

to fast forward

orreverseatrack.

Press

totemporarilystopCDplayback.

Press

againtoresumeplayback.

Press INTtoplaythefirst10secondsofeachtrack.

Press INT to cancel.

Press RPTtocontinuouslyrepeatselectedtrack.

Press RPT to cancel.

Press RDMtoplayalltracksinrandomorder.

Press RDM again to cancel.

Some CD-Rs and CD-RWs may be incompatible with this

unit, depending on media type and recording method.

Note:CD-Rrecordingsessionsmustbeclosed(finalized)for

playback.

Insert CD

Eject CD

Track Select

Fast Forward and Reverse

Pause

Intro

Repeat

Random

CD-R/CD-RW

Compatibility

XD1225 OPERATION

Troubleshooting

Problem Cause Action

Yellow wire not connected or incorrect voltage

Red wire not connected or incorrect voltage

Checkconnectionsforpropervoltage

(11~16VDC)

Blackwirenotconnected Checkconnectiontoground

Fuse blown Replace fuse

Speakerwiresnotconnected Checkconnectionsatspeakers

Oneormorespeakerwirestouchingeach

other or touching chassis ground

Insulateallbarespeakerwiresfrom

each other and chassis ground

Yellow or red wire touching chassis ground Checkforpinchedwire

Speakerwirestouchingchassisground Checkforpinchedwire

Incorrect fuse rating Use fuse with correct rating

Unit is not mounted correctly

CD mechanism position out of alignment

CD transit screws still in place

Checkmountingsleeveoradda

backstrapsupport

Physicaldefectinmedia(CD,CD-RorCD-

RW) Checkmediaforscratches

Press EJECT for 3 seconds to reset

CD mechanism position

Remove 2 transit screws located on top

of the unit.

Unit will not turn on

(nopower)

Unit has power

(butnosound)

Unit blows fuses

Excessiveskipping

Unit will not accept

a disc

Error Codes

Error Code Cause Action

ER-1appearsondisplay Disc error PressejectorRESET

ER-2 appears on display Mechanism error or disc is in upside down PressejectorRESET

ER-3 appears on display Servo error PressejectorRESET

XD1225 OPERATION

Limited One Year Warranty

Thiswarrantygivesyouspecificlegal

rights. You may also have other rights

which vary from state to state.

Dual Electronics Corp. warrants this

product to the original purchaser to be free

fromdefectsinmaterialandworkmanship

for a period of one year from the date of

the original purchase.

Dual Electronics Corp. agrees, at our

option, during the warranty period,

to repair any defect in material or

workmanshiportofurnishanequal

new, renewed or comparable product

(whicheverisdeemednecessary)in

exchangewithoutcharges,subjectto

verification of the defect or malfunction and

proofofthedateofpurchase.Subsequent

replacement products are warranted for

the balance of the original warranty period.

Who is covered?Thiswarrantyisextended

to the original retail purchaser for products

purchasedfromanauthorizedDualdealer

and used in the U.S.A.

What is covered?Thiswarrantycoversall

defectsinmaterialandworkmanshipin

thisproduct.Thefollowingarenotcovered:

software, installation/removal costs,

damage resulting from accident, misuse,

abuse, neglect, product modification,

improper installation, incorrect line

voltage,unauthorizedrepairorfailure

to follow instructions supplied with the

product, or damage occurring during

return shipment of the product. Specific

license conditions and copyright notices for

the software can be found via www.dualav.

com.

What to do?

1.Beforeyoucallforservice,checkthe

troubleshooting guide in your owner’s

manual.Aslightadjustmentofany

custom controls may save you a service

call.

2.Ifyourequireserviceduringthe

warranty period, you must carefully

packtheproduct(preferablyinthe

originalpackage)andshipitbyprepaid

transportation with a copy of the original

receipt from the retailer to an

authorizedservicecenter.

3. Please describe your problem in

writing and include your name, a

returnUPSshippingaddress(P.O.Box

not acceptable), and a daytime phone

number with your shipment.

4. For more information and for the

locationofthenearestauthorized

service center please contact us by one

ofthefollowingmethods:

•Callustoll-freeat1-866-382-5476

•E-mailusat[email protected]

ExclusionofCertainDamages:This

warranty is exclusive and in lieu of any

and all other warranties, expressed or

implied, including without limitation the

implied warranties of merchantability and

fitness for a particular purpose and any

obligation, liability, right, claim or remedy

in contract or tort, whether or not arising

from the company’s negligence, actual

or imputed. No person or representative

isauthorizedtoassumeforthecompany

any other liability in connection with the

sale of this product. In no event shall the

company be liable for indirect, incidental or

consequentialdamages.

XD1225 WARRANTY

XD1225 OPERATION

FCC Compliance

ThisdevicecomplieswithPart15oftheFCCRules.Operationissubjecttothefollowing

twoconditions:

(1)thisdevicemaynotcauseharmfulinterference,and

(2)thisdevicemustacceptanyinterferencereceived,includinginterferencethatmay

cause undesired operation.

Warning:Changesormodificationstothisunitnotexpresslyapprovedbytheparty

responsibleforcompliancecouldvoidtheuser’sauthoritytooperatetheequipment.

Note:ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassB

digitaldevice,pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovide

reasonableprotectionagainstharmfulinterferenceinaresidentialinstallation.This

equipmentgenerates,usesandcanradiateradiofrequencyenergyand,ifnotinstalled

and used in accordance with the instructions, may cause harmful interference to radio

communications.However,thereisnoguaranteethatinterferencewillnotoccurina

particularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradioor

televisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,the

user is encouraged to try to correct the interference by one or more of the following

measures:

Reorient or relocate the receiving antenna.•

Increasetheseparationbetweentheequipmentandreceiver.•

Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthe•

receiver is connected.

Consultthedealeroranexperiencedradio/TVtechnicianforhelp.•

Specifications

Frequencyresponse:20Hz-20kHz

Channelseparation@1kHz:>65dB

D/Aconverter:1 Bit

Tuningrange:87.5MHz-107.9MHz

Usablesensitivity:12dBf

50dBquietingsensitivity:16dBf

Stereoseparation@1kHz:40dB

Frequencyresponse:30Hz-13kHz

Tuningrange:530kHz-1710kHz

Usablesensitivity:30uV

Frequencyresponse: 80Hz-2kHz

Speakeroutputimpedance: 4~8 ohms

Fuse:5 amp AGC

Dimensions:7" x 7" x 2" (178 x 178 x 51 mm)

Designandspecificationssubjecttochangewithoutnotice.

CD Player

FMTuner

AMTuner

General

CEA-2006 Power Standard Specifications

(reference:14.4VDC+/-0.2V,20Hz~20kHz)

PowerOutput:5WattsRMSx4channelsat4ohmsand<1%THD+N

Signaltonoiseratio:75dBA(reference:1wattinto4ohms)

Dual Electronics Corp.

TollFree:1-866-382-5476

www.dualav.com

NSA0710-V02

Dual XD1225 User manual

Brand: Dual

Model: XD1225

Category: Car media receivers

Type: User manual

Download PDF

report

Dual XD1225 User manual

Dual XD1225 User manual

Related papers

Other documents