Data Connect DSP9612 User manual

Brand: Data Connect

Model: DSP9612

Category: Networking

Type: User manual

This manual is also suitable for

DSP19.2

Data Connect DSP9612 is a Fast Poll Modem designed for 4-wire, full-duplex or 2-wire, half-duplex operation over a voice-band leased line or private line. The modem is designed utilizing the latest digital-signal processing (DSP) technology to achieve high performance. The modem employs efficient modulation and encoding scheme to achieve fast modem training time. The modem is also backward compatible with Bell 202 and ITU-T V.23 modems.

DATA CONNECT ENTERPRISE

User’s Manual

For

DSP19.2 & DSP9612

Fast Poll Modem

Document Number 520-01001-101 Rev. A

Web site: www.data-connect.com

The products and programs described in this User’s Manual are licensed products of Data connect

Enterprise. This User’s Manual contains proprietary information protected by copyright, and this

User’s Guide and all accompanying hardware and documentation are copyrighted.

Data Connect Enterprise. does not warrant that the product will work in all environments and

applications, and makes no warranty and representation, either implied or expressed, with respect to

the quality, performance, merchantability, or fitness for a particular purpose.

Information in this User’s Guide is subject to change without notice and does not represent a

commitment on the part of Data Connect Enterprise. Data Connect Enterprise. assumes no

responsibility for any inaccuracies that may be contained in this User’s Manual.

No part of this manual may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, recording, or information storage and retrieval systems, for any

purpose other than the purchaser's personal use, without the express written permission of Data

Connect Enterprise

DSP19.2 Fast Poll Modem User’s Manual

520-01001-101 Rev. A

December 2007

DATA CONNECT ENTERPRISE

iii User’s Manual - DSP19.2 Fast Poll Modem

Contents

Chapter 1 Introduction............................................................................................ 6

Features......................................................................................................................7

Applications.................................................................................................................8

Chapter 2 Installation.............................................................................................. 9

Unpacking Your Hardware..........................................................................................9

Additional Items You Need to Complete Your Installation...........................................9

Hardware Overview...................................................................................................10

Front View.................................................................................................................10

Back View..................................................................................................................10

Rack-Mount View......................................................................................................11

Installation Summary.................................................................................................11

Configuring the Modem.............................................................................................12

Setting the DIP Switches...........................................................................................14

S1-1, S1-2, S1-3 − Modem Data Rate.................................................................15

S1-4 − Async Character (Fast-Poll Mode Only) ..................................................15

S1-5 − Auto RTS .................................................................................................15

S1-6 − Transmit Carrier Control ..........................................................................15

S1-7 − 2 or 4-Wire Operation ..............................................................................16

S1-8 − Transmitter Impedance............................................................................16

S1-9 − Remote Loopback Enable........................................................................16

S1-10 − Reserved (Test Only).............................................................................17

S2-1 through S2-3 − Transmit Level....................................................................17

S2-4 − Receiver Dynamic Range........................................................................17

S2-5 and S2-6 − Cable Equalizer (Fast-Poll Mode Only)....................................18

S2-7 − Anti-streaming..........................................................................................18

S2-10 − RTS-CTS Delay (Bell 202 Mode Only) ..................................................18

Configuring the Jumper Blocks .................................................................................19

For Stand-alone Units..........................................................................................19

For Rack-Mount Plug-in Modules........................................................................19

Connecting to a Transmission Line...........................................................................19

Connecting to a Voltage Source................................................................................21

Connecting to an RS-232 Device..............................................................................22

Connecting to an RS-485 Device..............................................................................22

LEDs..........................................................................................................................23

Loopback Control Switch...........................................................................................23

Contents

iv User’s Manual - DSP19.2 Fast Poll Modem

Appendix A Troubleshooting................................................................................ 25

Problem Solving........................................................................................................25

Appendix B Specifications ................................................................................... 26

General Specifications ..............................................................................................26

Mechanical Specifications.........................................................................................27

Interface Connector Pin Assignments.......................................................................27

RS-232 (DTE) Interface.............................................................................................28

RS-485 (DTE) Interface.............................................................................................28

Environmental Specifications....................................................................................28

Appendix C Limited Product Warranty................................................................ 29

Appendix D RMA Procedure................................................................................. 30

Contents

v User’s Manual - DSP19.2 Fast Poll Modem

Figures

Figure 1-1. Point-to-Point Network Using the DSP19.2FP Modem.........................................8

Figure 1-2. Multipoint Polling Network Using the DSP19.2FP Modem...................................8

Figure 2-1. Front View of the DSP19.2 Modem....................................................................10

Figure 2-2. Back View of DSP19.2 Modem...........................................................................10

Figure 2-3. Rack-Mount Module for the DSP19.2-RM Modem Board...................................11

Figure 2-4. DSP19.2 Fast-Poll Stand-alone Modem Board..................................................13

Figure 2-5. DSP19.2 Fast-Poll Rack-mount Modem Board ..................................................13

Figure 2-6. DSP19.2 Modem Transmission Line Interface...................................................20

Figure 2-7. Pin Locations on the Modem’s RJ-11C Jack......................................................22

Figure 2-8. Loopback Diagnostic Modes...............................................................................24

Figure 2-9. Back-to-Back Connection to a Second Modem..................................................27

Tables

Table 2-1. Modem Switch Settings .......................................................................................14

Table 2-2. Modem Operating Speed.....................................................................................15

Table 2-3. Transmit Levels....................................................................................................17

Table 2-4. Transmission Line Connector Pin Assignments ..................................................20

Table 2-5. RJ-11C Modular Jack Pin Assignments...............................................................22

Table 2-6. Modem LEDs.......................................................................................................23

Table A-1 Problem Solving ..................................................................................................25

Table B-1. Leased Line Terminal Block Pin Assignments ....................................................27

Table B-2. RS-232 (DTE) Interface.......................................................................................28

Table B-2. RS-485 (DTE) Interface.......................................................................................28

DATA CONNECT ENTERPRISE

6 User’s Manual - DSP19.2 Fast Poll Modem

Chapter 1

Introduction

Thank you for purchasing DCE’s DSP19.2 fast poll modem, the finest industrial-grade fast-

poll modem available.

The DCE modem is a 19200/9600/2400/1200 bps modem designed for 4-wire, full-duplex or

2-wire, half-duplex operation over a voice-band leased line or private line. The modem is

designed utilizing the latest digital-signal processing (DSP) technology to achieve high

performance. The modem employs efficient modulation and encoding scheme to achieve

fast modem training time. The modem is also backward compatible with Bell 202 and ITU-T

V.23 modems.

The DSP19.2 is the most technologically advanced modem on the market. Boasting a fast

DSP processor and automatic adaptive equalizer, the DSP19.2 modem is ideally suited for

multi-point communication systems that require fast response time, short training time, and

low throughput delay.

This User’s Guide describes the DSP19.2 (AC-powered) and DSP19.2-LV (DC-powered)

stand-alone modems, as well as the rack-mount DSP19.2-RM plug-in module for the

Motorola/UDS RM16M. This manual is designed to get your modem “up and running” as

quickly as possible. It contains all the information you need to configure and install your

modem. It also contains troubleshooting information in the unlikely event you encounter a

problem with your modem.

Introduction

7 User’s Manual - DSP19.2 Fast Poll Modem

Features

The DSP19.2 modem is specifically designed for harsh environments typically associated in

utility substations and industrial facilities. Though functionally similar to commercial modems,

the DSP19.2 provides the following unique features that make it well suited for utility and

industrial applications.

y Packaged in a rugged, compact enclosure for industrial applications.

y Leased-line interface protected with heavy-duty surge protection devices.

y Built-in hardware watchdog timer for software lock-up prevention without

requiring human intervention, making it ideal for unmanned locations.

y Works within an extended temperature range of -40ºC to +85ºC.

y Designed with coupling transformers for high-voltage isolation and common

mode noise rejection in industrial and commercial environments.

y Operate over voice-band conditioned or unconditioned leased-line and pilot

wires.

y Accepts power from a wide range of AC and DC power supplies:

– DSP19.2: 90 to 265 VAC or 100 to 400 VDC

– DSP19.2-LV: 10 to 60 VDC

– DSP19.2-RM: Plug-in module for the Motorola/UDS RM16M modem nest

y Standard industrial connectors for data, analog, and power interfaces allow

reliable interconnection to other industrial equipment.

y Asynchronous data rates (selectable) of 19200, 9600, 2400, and 0-1800 bps.

y Easily accessible DIP switches for user configuration and option selection.

y DB9-F connector for RS-232/V.24 interface, and RJ-11 for RS-485.

y Local analog, local digital, and remote digital loopback diagnostics.

Introduction

8 User’s Manual - DSP19.2 Fast Poll Modem

Applications

The DSP19.2 modem is designed for point-to-point and multipoint data communications.

Figure 1-1 shows a typical point-to-point configuration using the DSP19.2 modem and

Figure 1-2 shows a typical multipoint configuration using the DSP19.2 modem.

Workstation

Modem

Remote Terminal

Figure 1-1. Point-to-Point Network Using the DSP19.2 Modem

Workstation

Modem

Remote Terminal

Figure 1-2. Multipoint Polling Network Using the DSP19.2 Modem

There are a number of factors that can affect the modem’s operation and performance.

These include:

y Modem speed (i.e. bit error rate, transmission line distance)

y 2-wire or 4-wire configuration

y Transmission line characteristics, noise, and line impairments

y Network configuration (point-to-point or multipoint)

DATA CONNECT ENTERPRISE

9 User’s Manual - DSP19.2 Fast Poll Modem

Chapter 2

Installation

This chapter describes how to configure and install the modem to maximize the performance

and to match with your Data Terminal Equipment (DTE) or Remote Terminal Unit (RTU).

Unpacking Your Hardware

Your package should include:

y At least one of the following DSP19.2 modems:

– Model DSP19.2 for 90 to 265 VAC

– Model DSP19.2-LV for 10 to 60 VDC

– Model DSP19.2-RM for RM16M plug-in module

y A switching power supply module for 90-265VAC input (model DSP19.2 only)

y A leased-line cable with optional earth ground conductor (for stand-alone units

only)

y A DC power cable (model DSP19.2-LV modem only)

y This User’s Manual or CD-ROM

If your package contents are damaged or missing, contact your place of purchase.

Additional Items You Need to Complete Your Installation

To complete your installation and operate your modem, you need these additional items:

y Two- or four-wire transmission line or leased line

y A DB-9 data cable for your RS-232 interface Data Terminal Equipment (DTE)

port, or a RJ-11C data cable for your RS-485 DTE.

y Power supply that provides either:

– 90 to 265 Volts AC, 50 to 60 Hz, single phase or 100 to 400 VDC (if you have

the model DSP19.2 modem), or

– 10 to 60 Volts DC (if you have the model DSP19.2-LV modem)

– For the DSP19.2-RM, consult the documentation for your Motorola/UDS

RM16M

Installation

10 User’s Manual - DSP19.2 Fast Poll Modem

Hardware Overview

Front View

Figure 2-1 shows the front view of the DSP19.2 stand-alone modem. Starting from the left

side, this view shows:

y A set of eight LEDs for modem interface status (see Table 2-6 on page 23)

y A loopback control push-button switch (see Loopback Control Switch on page 23)

Figure 2-1. Front View of the DSP19.2 Modem

Back View

Figure 2-2 shows the back view of the DSP19.2 stand-alone modem. Starting from the left

side, this view shows:

y A 4-wire/2-wire configuration block labeled LEASED LINE

y An RJ-11 modular jack labeled RS-485 for connecting the modem to an RS-485

RTU

y A female, 9-pin RS-232 connector labeled RS-232 for connecting the modem to a

standard DTE (RTU)

y A power connector labeled 10-48V DC

Figure 2-2. Back View of DSP19.2 Modem

Installation

11 User’s Manual - DSP19.2 Fast Poll Modem

Rack-Mount View

Figure 2-3 shows the rack-mount plug-in module.

Figure 2-3. Rack-Mount Module for the DSP19.2-RM Modem Board

Installation Summary

This section describes the steps for installing the modem.

NOTE:

It is important to follow the steps below to configure the modem’s DIP

switches to match your DTE/RTU interface requirement and the transmission

line characteristics. If you are not certain about your system’s parameters or

the leased-line configuration, please contact your network administrator for

assistance.

1. Configure the modem using the DIP switches and jumpers. See pages 14 and

19.

2. Connect to a transmission line. See page 19.

3. Connect to a voltage source. See page 21.

4. Connect a DTE device. See page 22.

Installation

12 User’s Manual - DSP19.2 Fast Poll Modem

Configuring the Modem

You configure the modem using the two sets of DIP switches and two sets of configuration

jumpers on the printed circuit board of the modem labeled S1 and S2, JP1 and JP3.

Configuration DIP switches S1 and S2 for the stand-alone and rack-mount modems are

identical. Their descriptions in this user’s manual apply to both modem versions.

Configuration jumper JP1 for the rack-mount modem card is used to select receiver

termination impedance.

It is important to follow the steps described below, in the order shown, to ensure that you

configure your modem properly using the modem DIP switches:

1. Use DIP switch 1 (S1) to configure the modem for your host DTE interface and

network topology. Using S1, you select the modem’s operating speed to match

you host computer or RTU devices, and other DTE specific operating

parameters.

2. Use DIP switch 2 (S2) to select the modem’s transmitter output level and receiver

dynamic range specific leased line conditions. The S2 settings apply for both

high-speed fast-poll (QAM) and low-speed (FSK) modes.

3. After you change the DIP switch settings, recycle power to the modem to have

the settings take effect.

NOTE:

The DIP switch settings will not take effect until you recycle power to the

modem.

To access the configuration DIP switches and jumpers on the stand-alone modem:

1. Ground yourself to discharge any ESD, which might cause damage to the

sensitive devices on the modem board.

2. Use a small Philips screw driver to remove the rear panel and carefully slide the

modem board out of the enclosure. The location of the DIP switches and jumpers

for the stand-alone modem are shown in Figure 2-4. For DIP switches and

jumpers on the rack-mount plug-in module, see Figure 2-5.

3. Carefully return the modem board into the enclosure. Then replace the rear panel

after the configuration is completed.

Installation

13 User’s Manual - DSP19.2 Fast Poll Modem

D17 D18 D19 D20 D21 D22 D23

J1J2

T2 T3

GT3GT2

U10

F1 F2 F3 F4

D24

11 10

JP1

Configuration Switches

S1 & S2

RS232

RS485

JP3

600

Hi-Z

Configuration Jumpers

JP1 & JP3

JP2

Figure 2-4. DSP19.2 Fast-Poll Stand-alone Modem Board

U19

U15

GT2 GT1

U18

U17

D11 D10

U15

Data Rate 1

Data Rate 2

Data Rate 3

Char Length

Auto RTS

Tx Carrier

4W/2W

Tx Impedance

RDLB Disable

Factory only

D2 D1D3D4D5D6D7D8D9

U10

U12

GT4 GT3

D27 D25

13 14

U22

U14

S1 S2

U21

JP1

600 ohmHigh-Z

Configuration Jumper

for Receiver Termination

Configuration DIP Switches

Figure 2-5. DSP19.2 Fast-Poll Rack-mount Modem Board

Installation

14 User’s Manual - DSP19.2 Fast Poll Modem

Setting the DIP Switches

S1 and S2 are 10-position DIP switches used to configure all the options and features of the

modem. Table 2-5 shows the setting of the switches.

NOTE:

Switches S1 and S2 are toggle switches. To configure the switches, use a

small sharp pin to firmly press down on one end to open or to close each

switch. Never leave any switch in half open and half close. Press down on the

side of the switch labeled OPEN is referring to as OFF condition. When the

switch is CLOSED, it is in the ON state.

Table 2-1. Modem Switch Settings

Switch Settings

DIP Switches

ON OFF (Default)

DIP Switch S1

S1-1 to S1-3: Modem Data Rate

19200

: SW1=OFF, SW2=OFF, SW3=OFF

9600

: SW1=ON, SW2=OFF, SW3=OFF

2400

: SW1=OFF, SW2=ON, SW3=OFF

Bell 202T

: SW1=OFF, SW2= OFF, SW3= ON

V.23:

SW1=ON, SW2=ON, SW3=ON

S1-4: DTE Async Character

11 bit 10 bit

S1-5: Auto RTS

Enable Disable

S1-6: Transmit Carrier Control

Constant On Controlled by RTS

S1-7: 2- or 4-wire leased line

2-wire half duplex 4-wire full duplex

S1-8: Transmitter Impedance

Controlled by RTS 600 ohms

S1-9: Remote Digital Loopback

Enable Disable

S1-10: Test Only (Reserved)

Test only Normal

DIP Switch S2

S2-1 to S2-3: Transmit Output Level

From -12 to +3 dBm (see Table 2-5)

S2-4: Modem Receive Dynamic Range

-10 to -43dBm +3 to -30dBm

S2-5: TX Cable Equalizer

Enabled Disabled

S2-6: RX Cable Equalizer

Enabled Disabled

S2-7: Anti-streaming

Active Inactive

S2-8: RTS-CTS Delay (Bell 202T only)

33 msec 8 msec

NOTE:

Switches S2-9 and S2-10 are for future options.

Installation

15 User’s Manual - DSP19.2 Fast Poll Modem

S1-1, S1-2, S1-3 − Modem Data Rate

y S1-1, S1-2, S1-3: Select the modem speed per Table 2-2

Table 2-2. Modem Operating Speed

To Select… Set Switch S1-1 to… Set Switch S1-2 to… Set Switch S1-3 to…

19,200 bps OFF OFF OFF

9600 bps ON OFF OFF

2400 bps OFF ON OFF

Bell 202T OFF OFF ON

V.23/1200 ON ON ON

For modem speeds of 2400 bps or higher, the modem uses QAM modulation automatically.

When the modem is operating at 1200 bps either in Bell202T or ITU-V.23 mode, the modem

uses FSK modulation.

S1-4 − Async Character (Fast-Poll Mode Only)

y S1-4 ON = 11 bits

y S1-4 OFF = 10 bits (default)

Switch S1-4 selects whether the async character is 10 or 11 bits long. This switch setting is

ignored when the modem uses FSK modulation.

S1-5 − Auto RTS

y S1-5 ON = Enable Auto RTS

y S1-5 OFF = Disable Auto RTS (default)

For data terminals that do not provide hardware Request To Send (RTS), set switch S1-5 to

ON to enable auto RTS mode. In this mode, TXD is detected at the modem and an internal

RTS signal is turned ON. After training completes, the TXD is transmitted to the remote

modem. The transmitter turns itself off if no TXD is detected after a pre-determined length of

idle time.

S1-6 − Transmit Carrier Control

y S1-6 ON = Constant carrier

y S1-6 OFF = Controlled by RTS (default)

Switch S1-6 selects either constant or switched carrier. Constant carrier allows DTEs, such

as asynchronous terminals or RTUs, to operate with modems, without requiring an input

Installation

16 User’s Manual - DSP19.2 Fast Poll Modem

RTS signal. If you enable constant carrier (switch S1-6 = ON), the modem forces the

transmit carrier active and the RTS-CTS delay is shortened to less than 0.5 ms.

You can use constant carrier in 4-wire point-to-point, or at the master unit of multi-point

network applications to reduce modem training time.

In switched-carrier mode (switch S1-6 = OFF), the RTS-CTS delay is 23 ms for 2400 bps

and above.

S1-7 − 2 or 4-Wire Operation

y S1-7 ON = 2-Wire, Half-Duplex Mode

y S1-7 OFF = 4-Wire, Full-Duplex Mode (default)

Switch S1-7 configures the modem for either 4-wire full-duplex or 2-wire half-duplex

operation.

S1-8 − Transmitter Impedance

y S1-8 ON = Switched by RTS

y S1-8 OFF = 600 Ω (default)

Switch S1-8 is used for multi-point configuration networks. When multiple modems are

connected on the same metallic circuit:

y The transmitter termination should be of high impedance if the modem is not

transmitting in order not put a load on the line.

y The transmitter is only terminated with 600 ohms when RTS is asserted.

This configuration should be used for all slave modems to prevent the transmitting modem

from being unnecessarily burdened. To select this configuration, set switch S1-8 ON for the

slave modems.

If you use the modem with transmission lines that are transformer-coupled or with an

impedance-isolated network (such as a transformer bridge), set switch S1-8 OFF for proper

operation.

S1-9 − Remote Loopback Enable

y S1-9 ON = Loopback enabled

y S1-9 OFF = Loopback disabled (default)

During instances of channel noise, the modem may mistake a received preamble as a

request to go into remote digital loopback. Setting switch S1-9 to OFF prevents the modem

Installation

17 User’s Manual - DSP19.2 Fast Poll Modem

from participating in a remote digital loopback with another modem. Switch S1-9 does not

prevent the modem from sending a remote digital loopback request to a remote modem.

S1-10 − Reserved (Test Only)

y S1-10 = must be OFF

Switch S1-10 must be in the OFF position for normal operation. It is reserved for factory

testing only.

S2-1 through S2-3 − Transmit Level

Switches S2-1 through S2-3 adjust the modem’s transmit level. Table 2-5 shows the transmit

levels you can select using these switches.

Table 2-3. Transmit Levels

S2-1 through S2-3 Switch Settings

Transmit Level

S2-1 S2-2 S2-3

0 dBm OFF OFF OFF

−2 dBm

OFF OFF ON

−4 dBm

OFF ON OFF

−6 dBm

OFF ON ON

−8 dBm

ON OFF OFF

−10 dBm

ON OFF ON

−12 dBm

ON ON OFF

+3 dBm ON ON ON

S2-4 − Receiver Dynamic Range

y S2-4 ON = −10 to −43 dBm

y S2-4 OFF = +3 to −30 dBm (default)

For short distances or to select a strong receive signal, set S2-4 to OFF. For a long-distance

cable or low receive signal level, set S2-4 to ON (−43 dBm).

Installation

18 User’s Manual - DSP19.2 Fast Poll Modem

S2-5 and S2-6 − Cable Equalizer (Fast-Poll Mode Only)

y S2-5 ON = Enable TX Cable Equalizer

S2-5 OFF = Disable TX Cable Equalizer (default)

y S2-6 ON = Enable RX Cable Equalizer

S2-6 OFF = Disable RX Cable Equalizer (default)

If you use the DSP19.2 as a limited-distance modem over pilot wire or unloaded cables, you

may need to improve or extend the modem’s polling performance on long transmission lines

by using the modem’s internal fixed Compromise Cable Equalizer when polling on long

metallic circuits. The cable equalizer is active only when the modem is in QAM fast-poll

mode (2400 bps or higher).

S2-7 − Anti-streaming

y S2-7 ON = Anti-streaming is active

S2-7 OFF = Anti-stream is inactive (default)

Typically, anti-streaming is used in multi-point applications to prevent a malfunctioning slave

data terminal or RTU from occupying the line indefinitely. When anti-streaming is active, the

modem can transmit data for a maximum of 27 seconds before the transmitter turns off

automatically. The modem then looks for an ON-to-OFF RTS transition before proceeding

with normal operation. Anti-streaming can be selected in either high-speed or low-speed

mode.

S2-10 − RTS-CTS Delay (Bell 202 Mode Only)

y S2-10 ON = 33.0 ms delay

y S2-10 OFF = 8.0 ms delay (default)

Switches S2-10 determines the duration of the RTS-CTS delay in Bell 202 mode.

For V.23 mode, the RTS-CTS delay is fixed at 33 ms.

Installation

19 User’s Manual - DSP19.2 Fast Poll Modem

Configuring the Jumper Blocks

For Stand-alone Units

Jumper block JP1 is use to select RS-232/V24 or RS-485 interface with your DTE or RTU.

• RS-232: Two shorting jumpers are placed over pins 1 & 3, and 2 & 4 (default)

• RS-485: Place two shorting jumpers over pins 3 & 5, and 4 & 6

Jumper block JP3 is used to set the modem’s receiver termination impedance

• 600 ohms: A shorting jumper is placed over pins 2 & 3 (default)

• High impedance: Place a shorting jumper over pins 1 & 2

For Rack-Mount Plug-in Modules

Jumper block JP1 is used to set the modem’s receiver termination impedance

• 600 ohms: A shorting jumper is placed over pin 2 & 3 (default)

• High impedance: A shorting jumper is placed over pin 1 & 2

Select high receiver impedance (Hi-Z) if multiple modems are connected in a multi-

point configuration but without an impedance matching bridged such as private

metallic circuit environment. In this configuration, only one receiver should be

configured for 600 ohms.

Connecting to a Transmission Line

The modem has a transmission line interface that can be configured for 2- or 4-wire analog

connection, where one pair (Tx-A and Tx-B) is used to transmit data and the other pair (Rx-A

and Rx-B) is used to receive data. The transmit pair and receive pair are non-polarized.

Table 2-4 shows the pin numbers and corresponding signals for the modem. Figure 2-6

shows the transmission line interface.

NOTE:

For communication to occur, the Rx line of one modem must connect to the Tx

line of the other modem. The modem’s Tx/Rx pair are non-polarized.

NOTE:

The modem does not support leased-line operation with DC shielding current.

Leased-line connector pin assignments for the rack-mount module can be

found in the documentation for your Motorola/UDS RM16M.

Installation

20 User’s Manual - DSP19.2 Fast Poll Modem

Table 2-4. Transmission Line Connector Pin Assignments

This Pin Number… Corresponds to This Signal…

1 Rx

2 Rx

3 Tx (Tx/Rx)

4 Tx (Tx/Rx)

5 Earth Ground (optional)

NOTE:

When 2-wire half duplex is used, the TX pair must be used for both transmit

and receive.

Figure 2-6. DSP19.2 Modem Transmission Line Interface

Page is loading ...

Data Connect DSP9612 User manual

Brand: Data Connect

Model: DSP9612

Category: Networking

Type: User manual

This manual is also suitable for

DSP19.2

Download PDF

report

Data Connect DSP9612 User manual

This manual is also suitable for

Data Connect DSP9612 User manual

Other documents