BLACK+DECKER KS890E User manual

Category
Power tools
Type
User manual

This manual is also suitable for

3
SAFETY INSTRUCTIONS
Warning! When using electric tools, the following
basic safety precautions should always be taken to
reduce the risk of fire, electric shock and personal
injury. Read all these instructions before attempting to
operate the product and save this booklet.
For safe operation:
Keep the work area clean. Cluttered areas and
benches invite injuries.
Consider the work area environment. Do not expose
the power tool to rain and do not use in damp or wet
locations. Keep the work area well lit. Do not use
the power tool where there is a risk to cause fire
or explosion.
Guard against electric shock. Avoid body contact,
where possible, with earthed or grounded surfaces
(e.g. pipes, radiators, ranges and refrigerators).
Keep children away. Do not let visitors touch the
tool or extension cord. All visitors should be kept
away from the work area.
Store idle tools. When not in use, tools should be
stored in a dry, high or locked place, out of reach
of children.
Do not force the tool. It will do the job better and
more safely at the rate for which it was intended.
Use the right tool. Do not force small tools or
attachments to do the job of a heavy duty tool.
Do not use the tool for purposes not intended; for
example, do not use a circular saw or Scorpion Saw
to cut tree limbs or logs.
Dress properly. Do not wear loose clothing or
jewellery as they can be caught in moving parts.
Rubber gloves and non-skid footwear are
recommended when working outdoors.
Wear protective hair covering to contain long hair.
Use safety glasses. Use a face or dust mask as
well, if the operation is dusty or if the tool is being
used in enclosed spaces.
Do not abuse the cord. Never carry the tool by its
cord or yank it to disconnect it from the socket. Keep
the cord away from heat, oil and sharp edges.
Secure the work. Use clamps or a vice to hold the
work. It is safer than using a hand and it frees both
hands to operate the tool.
Do not overreach. Keep proper footing and balance at
all times.
Maintain the tool with care. Keep a cutting tool
sharp and clean for better and safer performance.
Follow the instructions for lubricating and changing
accessories. Inspect the tools cord periodically
and, if damaged, have repaired by an authorised
service facility. Inspect the extension cord
periodically and replace if damaged. Keep the
handles dry, clean and free from oil and grease.
Disconnect the tool when not in use, before
servicing and when changing accessories such as
blades, bits and cutters.
Avoid unintentional starting. Do not carry a
plugged-in tool with a finger on the switch.
Ensure the switch is off when plugging in.
Use an outdoor extension cord. When a tool is
used outdoors, only use an extension cord
intended for outdoor use and so marked.
Stay alert. Watch what you are doing, use common
sense and do not operate the tool when tired.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
be carefully checked to determine whether it will
operate properly and perform its intended
function. Check for alignment of moving parts,
free running of moving parts, breakage of parts,
mounting and any other conditions that may affect
its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorised service centre unless otherwise
indicated in the product booklet. Have defective
switches replaced by an authorised service
centre. Do not use the tool if the switch does not
turn it on and off.
Warning! The use of any accessory or attachment,
other than recommended in the product booklet,
may present a risk of personal injury.
Have the tool repaired by a qualified person.
The electrical tool is in accordance with the
relevant safety requirements. Repairs should only
be carried out by qualified persons using original
spare parts, otherwise, this may result in
considerable danger to the user.
Save these instructions!
DOUBLE INSULATION
The tool is double insulated. This means that all
the external metal parts are electrically insulated
from the mains power supply. This is done by
placing insulation barriers between the electrical
and mechanical components making it
unnecessary for the tool to be earthed.
Scorpion Saw user manual
4
ENGLISH
Note: Double insulation does not take the place
of normal safety precautions when operating the
tool. The insulation system is for added
protection against injury resulting from a possible
electrical insulation failure within the tool.
ELECTRICAL SAFETY
Be sure the supply is the same as the voltage given on
the rating plate. The tool is fitted with a two-core cable
and plug.
MAINS PLUG REPLACEMENT (UK ONLY)
Should the mains plug need replacing and you are
competent to do this, proceed as instructed below.
If you are in doubt, contact a Black & Decker service
centre or a qualified electrician.
Disconnect the plug from the power supply.
Cut off the plug and dispose of safely. A plug with
bared copper conductors is very dangerous if
engaged in a live socket outlet.
Only fit BS1363A approved plugs fitted with the
correctly rated fuse.
Note: Fuses do not give personal protection against
electric shock.
The cable wire colours, or a letter, will be marked at
the connection point of most good quality plugs.
Attach the wires to their respective points in the
plug (see diagram). Brown is L (live) and blue is N
(neutral).
Fit a 5 amp fuse
approved
to BS1362
N
L
E
230 volts AC only
Never use a light
socket
Make sure that the
outer sheath of the
cable is held firmly
by the clamp
Fit a BS1363A
approved
resilient plug
Connect
blue to
N (neutral)
Connect
brown to
L (live)
Before replacing the top cover of the plug ensure
that the cable restraint is holding the outer sheath of
the cable firmly and that the two leads are correctly
fixed at the terminal screws. If the fuse cover is
missing or damaged do not use the plug.
For replacement or detachable fuse covers, contact
a Black & Decker service centre.
Warning! Never connect live or neutral wires to the
earth pin marked E or .
MAINS PLUG REPLACEMENT
(AUSTRALIA AND NEW ZEALAND ONLY)
Should the mains plug or cordset of the product be
damaged, it must only be replaced by an authorised
Black & Decker service agent because special
purpose tools are required.
EXTENSION CABLES
Up to 30m (100ft) of 3-core extension cable can be
used without undue loss of power.
Note: An extension cable should not be used unless
absolutely necessary. Use of an improper extension
cable could result in a risk of fire and electric shock.
If an extension cable must be used, make sure it is
properly wired, contains the correct rated fuse as
recommended in its literature and is in good
electrical condition.
PROTECTING THE ENVIRONMENT
Black & Decker provides a facility for recycling
Black & Decker products once they have
reached the end of their working life.
This service is provided free of charge. To take
advantage of this service please return your
product to any authorised repair agent who
will collect them on our behalf.
You can check the location of your nearest authorised
repair agent by contacting your local Black & Decker
office at the address indicated in this manual.
Alternatively, a list of authorised Black & Decker
repair agents and full details of our after-sales
service and contacts are available on the Internet at:
www.2helpU.com.
GUARANTEE
Black & Decker is confident of the quality of its
products and offers an outstanding guarantee.
This guarantee statement is in addition to and in no
way prejudices your statutory rights. The guarantee
is valid within the territories of the Member States of
the European Union and the European Free Trade Area.
5
If a Black & Decker product becomes defective due
to faulty materials, workmanship or lack of
conformity, within 24 months from the date of
purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair
wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
The product has been used for trade, professional
or hire purposes;
The product has been subjected to misuse or neglect;
The product has sustained damage through
foreign objects, substances or accidents;
Repairs have been attempted by persons other
than authorised repair agents or Black & Decker
service staff.
To claim on the guarantee, you will need to submit
proof of purchase to the seller or an authorised
repair agent. You can check the location of your
nearest authorised repair agent by contacting your
local Black & Decker office at the address indicated
in this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our
after-sales service and contacts are available on the
Internet at: www.2helpU.com
ACCESSORIES
The performance of any power tool is dependant upon
the accessory used. Black & Decker accessories are
engineered to high quality standards and are designed
to enhance the performance of your tool. Buying a
Black & Decker accessory will ensure that you get the
very best from your Black & Decker product.
TECHNICAL DATA
The level of sound pressure of the tool is in
accordance with EEC legislation. It is recommended
that you take appropriate measures for the protection
of your hearing if the sound level seems
uncomfortable. This normally equates to a sound
pressure in excess of 85dB (A).
KS890E
Volts (V) 230
Watts 400
Current (A) 1.8
SPM (/min) 0-5500
Stroke (mm) 10
FEATURES
1. Variable speed switch
2. Lock-off button
3. Shoe plate
4. Dust blow
5. Blade release
6. Soft grip
7. Second hand position
8. Large capacity blade
9. Curve cutting blade
10. Metal cutting blade
Your Scorpion Saw includes some or all of these
features.
Note: This user manual also covers catalogue
numbers with a letter suffix. Refer to your carton for
details of your product.
BEFORE USING YOUR SAW THINK!
Before you start cutting make sure that the area you
are going to cut is clear of all obstacles particularly
on the reverse side of the cut.
If you use the saw with one hand always ensure your
free hand is away from the cutting area.
REMOVAL & REFITTING THE BLADE
Your Scorpion Saw has a new blade clamping
mechanism. Before using the saw familiarize
yourself with the removal of the blade and refitting
the blade securely in the saw.
4
5
3
2
1
2
6
7
8910
ENGLISH
6
ENGLISH
Always ensure the unit is unplugged from the power
supply when changing blades.
Always ensure the tooth protector is fitted when
changing blades.
REMOVING THE BLADE
Ensure blade has cooled
after use. Press and hold
the rear of the blade
release button fully, hold
the back of the blade
and rotate the blade
through 90° as shown in
the diagram. Slide the
blade sideways off the
retaining pin and remove
from the saw.
FITTING A BLADE
Place the blade with the
tooth protector fitted
over the location pin.
The blade teeth should
be facing the handle.
Rotate the blade
through 90° until it is
fully located in the slot
and the location pin is
in the locked position.
To ensure the blade is
securely fitted try to
remove without pressing
the blade release button.
Remove the tooth
protector, your saw is
now ready for use.
Note: If you are unable to fit the blade, check if the
location pin is in the correct position as shown
below. If it is not, keep the blade release button
depressed and use a screwdriver to turn the location
pin into the correct position.
OPERATING YOUR SCORPION SAW
Variable speed trigger switch
Your Scorpion Saw is equipped with a variable speed
trigger switch that allows you greater control over
start of cut, rate of cut and breakthrough of cut.
To switch your Scorpion
Saw on, push lock-off
button (2) and squeeze
the on/off variable
speed trigger switch (1).
To switch off, release
the trigger, the unit will
automatically lock-off.
Standard Mode
To obtain the best results
from your Scorpion Saw,
use the same backward
and forward movement
you would employ with
a traditional hand saw.
This will enable a quicker cleaner cut.
Operating in Jigsaw Mode
Disconnect unit from
power supply. Remove
blade, rotate shoe
through 270˚ and secure
in position. Fit curve
cutting blade.
Remove tooth protector
and your Scorpion Saw
is now ready for use.
Cutting Metal
Your Scorpion Saw can be used for cutting light
gauge ferrous and non-ferrous metals such as
copper, brass, aluminium, etc. See recommended
materials.
It is advisable when cutting thin sheet to clamp a
backing sheet of soft wood or plywood to the work
as this will enable you to obtain a cleaner cut. Both
metal and wood backing are sawn together. Do not
force the cutting blade into the metal as this will
reduce the life of the blade and possibly damage the
motor. Cutting thin metal will take longer than cutting
even a relatively thick piece of wood, so do not be
tempted to speed up the operation by forcing the
saw. Spread a thin film of oil along the proposed
cutting line before cutting.
Only use the metal cutting blade for this purpose.
7
RECOMMENDED MATERIALS
Recommended materials Capacity
Large capacity blade
Soft wood Up to 100mm x 100mm
Plastic soil pipe Up to 125mm Ø
Curve cutting blade
Worktop Up to 50mm
Metal cutting blade
Ferrous/non-ferrous metals Up to 3mm thick
CLEANING
Disconnect your Scorpion Saw from the power supply.
Use only mild soap and a slightly damp cloth to clean
your Scorpion Saw. Many household cleaners contain
chemicals which could seriously damage the plastic.
Also, do not use petrol, turpentine, lacquer or paint
thinners or similar products. Never let any liquid get
inside the tool and never immerse any part of your
Scorpion Saw into liquid.
EC DECLARATION OF CONFORMITY
We declare that unit: KS890E conforms to
98/37/EC, 89/336/EEC, EN55014,
73/23/EEC, EN50144, EN61000
A weighted sound pressure 87dB (A)
A weighted sound power 100dB (A)
Hand/arm weighted vibration 3.4m/s
2
Kevin Hewitt
Director of Consumer Engineering
Spennymoor, County Durham DL16 6JG,
United Kingdom
The Black & Decker policy is one of continuous
improvement to our product and as such we reserve
the right to change the product specification without
prior notice.
ENGLISH
European Patent Application Numbers
993 102 62.3
993 102 61.5
993 102 63.1
Design Application Numbers
Country Application Number
China 99309679.4
China 99309680.8
Germany 499006043.1
Denmark 0746/99
Denmark 0745/99
France 004021
France 994024
GB 2080023
GB 2080024
Italy M1990000372
Italy M1990000372
Sweden 99-1132
Sweden 99-1133
US 29/106775
TYP.
KS890E
E12904.FH5
www.2helpU.com
14-02-00 CW
1
101
104
105
107
106
108
110
111
112
113
117
118
109
108
116
114
131
128
127
126
125
102
133
132
120
121
122
123
124
101
134
142
138
141
115
131
129
130
144
103
140
143
139
Part No: 574722-01
Australia DEWALT Industrial Power Tool Company Tel. 03 9895 9200
7 Clarice Road, Box Hill, Victoria 3128 Fax 03 9899 7465
Belgique/België Black & Decker (Belgium) N.V. Tel. 02/719.07.11
Weihoek 1, 1930 Zaventem Fax 02/721.40.45
Danmark Black & Decker Tel. 70 20 15 10
Hejrevang 26B, 3450 Allerød Fax 48 14 13 99
Internet: www.blackdecker.dk
Deutschland Black & Decker GmbH Tel. 06126/21 24 83
Black & Decker Str. 40, D - 65510 Idstein Fax 06126/21 26 01
EÏÏ¿˜ Black & Decker (EÏÏ¿˜) ∞.E. ∆ËÏ. (010) 8981 616
™ÙÚ¿‚ˆÓÔ˜ 7 & µÔ˘ÏÈ·Á̤Ó˘ 159 ∆ËÏ. (010) 8982 630
16674 °Ï˘Ê¿‰·, ∞ı‹Ó·, EÏÏ¿‰· º·Í Service (010) 8983 285
España Black & Decker Spain Tel. 934 797 400
Parque de Negocios “Mas Blau” Fax 934 797 419
Edificio Muntadas, c/Bergadá, 1, Of. A6
08820 El Prat de Llobregat (Barcelona)
France Black & Decker (France) S.A.S. Tel. 04 72 20 39 20
B.P. 21, 69571 Dardilly Cédex Fax 04 72 20 39 00
Helvetia ROFO AG Tel. 026-6749391
Gewerbezone Seeblick Fax 026-6749394
3213 Kleinbösingen
Italia Black & Decker Italia SpA Tel. 039-23871
Viale Elvezia 2 Fax 039-2387592/2387594
20052 Monza (MI) Numero verde 800-213935
Nederland Black & Decker (Nederland) BV Tel. 076-5082000
Florijnstraat 10, 4879 AH Etten-Leur Fax 076-5038184
New Zealand Black & Decker Tel. 09 579 7600
81 Hugo Johnson Drive Fax 09 579 8200
Penrose, Auckland, New Zealand
Norge Black & Decker (Norge) A/S Tlf. 22 90 99 00
Postboks 248, Leirdal, 1011 Oslo Fax 22 90 99 01
Internet: www.blackdecker.no
Österreich Black & Decker Vertriebsges.m.b.H Tel. 01 66116-0
Erlaaerstraße 165, 1231 Wien Fax 01 66116-14
Portugal Black & Decker Tel. 214667500
Rua Egas Moniz 173, Fax 214667575
S. João do Estoril 2766-651, Estoril
South Africa Black & Decker South Africa (Pty) Ltd Tel. (011) 653-1400
Physical address: Fax (011) 653-1499
39 Commerce Crescent
Eastgate, ext. 12, Sandton, Kramerville 2148
Postal address:
Postnet Suite 107, Private Bag X65
Halfway House 1685
Suomi Black & Decker Oy Puh: (09) 825 4540
Palotie 3, 01610 Vantaa Fax: (09) 825 45 444
Black & Decker Oy, Tel: (09) 825 4540
Brandvägen 3, 01610 Vanda Fax: (09) 825 45 444
Sverige Black & Decker AB Tel: 031-68 60 00
Box 603, 421 26 Västra Frölunda, Fax: 031-68 60 08
Besöksadr. Ekonomivägen 11
Türkiye Black & Decker Merkez Servis Tel. 0216 455 89 73
Dudullu Cad. Kerembey Sok. No. 1 Faks 0216 455 20 52
Küçükbakkalköy/Istanbul
United Kingdom Black & Decker Tel. 01753 511234
210 Bath Road Fax 01753 551155
Slough, Berkshire SL1 3YD Helpline 01753 574277
verktøj?
Onko tämä ensimmäinen
B&D-koneesi?
E›Ó·È ÙÔ ÂÚÁ·Ï›Ô
·˘Ùfi Ë ÚÒÙË Û·˜ ·ÁÔÚ¿?
Yes
Ja
Oui
Si
Ja
Sim
Ja
Ja
Ja
Kyllä
¡·È
No
Nein
Non
No
Nee
No
Não
Nej
Nei
Nej
Ei
√¯È
Dealer address
Händleradresse
Cachet du revendeur
Indirizzo del
rivenditore
Adres van de dealer
Dirección del detallista
Morada do
revendedor
Återförsäljarens adress
Forhandlerens adresse
Forhandler
adresse
Jälleenmyyjän osoite
¢È‡ı˘ÓÛË ·ÓÙÈÚÔÛÒÔ˘
...........................................................
...........................................................
Cat. no.:
Is this tool a gift?
Ist dieses Gerät
ein Geschenk?
S’agit-il d’un cadeau?
Si tratta di un regalo?
Kreeg u de
machine als cadeau?
¿Ha recibido
usted esta herramienta como regalo?
Recebeu esta ferramenta como
presente?
Är verktyget en gåva?
Er verktøyet en gave?
Er verktøjet
en gave?
Onko kone lahja?
∆Ô ÂÚÁ·ÏÂ›Ô Â›Ó·È ‰ÒÚÔ?
Yes
Ja
Oui
Si
Ja
Sim
Ja
Ja
Ja
Kyllä
¡·È
No
Nein
Non
No
Nee
No
Não
Nej
Nei
Nej
Ei
√¯È
Is this tool your first purchase?
Ist
dieses Gerät ein Erstkauf?
Est-ce un
1er achat?
Questo prodotto è il suo
primo acquisto?
Is deze machine uw
eerste aankoop?
¿Es esta
herramienta la primera de este tipo?
Esta ferramenta é a sua primeira
compra?
Är detta ditt första B&D-
verktyg?
Er dette ditt første B&D
verktøy?
Er dette dit første B&D
Dealer address Date of purchase
Händleradresse Kaufdatum
Cachet du revendeur Date d’achat
Indirizzo del rivenditore Data d’acquisto
Adres van de dealer Aankoopdatum
Dirección del detallista Fecha de compra
Morada do revendedor Data de compra
Återförsäljarens adress Inköpsdatum
Forhandlerens adresse Innkjøpsdato
Forhandler adresse Indkøbsdato
Jälleenmyyjän osoite Ostopäivä
¢È‡ı˘ÓÛË ·ÓÙÈÚÔÛÒÔ˘ ∏ÌÂÚÔÌËÓ›· ·ÁÔÚ¿˜
Name
Name
Nom
Nome
Naam
Nombre
Nome
Namn
Navn
Navn
Nimi
√ÓÔÌ·:
...........................................................
Address
Adresse
Adresse
Indirizzo
Adres
Dirección
Morada
Adress
Adresse
Adresse
Osoite
¢È‡ı˘ÓÛË:
...........................................................
...........................................................
Town
Ort
Ville
Cittá
Plaats
Ciudad
Localidade
Ort
By
By
Paikkakunta
¶fiÏË:
...........................................................
Postal code
Postleitzahl
Code
postal
Codice postale
Postcode
Código
Código postal
Postnr.
Postnr.
Postnr.
Postinumero
∫ˆ‰ÈÎfi˜
...........................................................
Data protection act: Tick the box if
you prefer not to receive further
information.
Bitte ankreuzen, falls Sie
keine weiteren Informationen erhalten
möchten.
Si vous ne souhaitez pas
recevoir d’informations, cochez cette
case.
Barrate la casella se non
desiderate ricevere informazioni.
A.u.b. dit vakje aankruisen indien u
geen informatie wenst te ontvangen.
Señale en la casilla sino quiere recibir
información.
Por favor, assinale com
uma cruz se não desejar receber
informação.
Vänligen kryssa för i
rutan om Ni inte vill ha information.
Vennligst kryss av dersom du ikke
ønsker informasjon.
Venligst sæt
kryds i ruden såfremt De ikke måtte
ønske at modtage information.
Merkitkää rasti ruutuun, mikäli ette
halua vastaanottaa informaatiota.
¶·Ú·Î·Ï›ÛÙ ӷ ÛËÌÂÈÒÛÂÙ ¿Ó
‰ÂÓ ı¤ÏÂÙ ӷ ¿ÚÂÙ ÏËÚÔÊÔڛ˜.
Part No: 574722-01
GUARANTEE CARD
GARANTIEKARTE
CARTE DE GARANTIE
TAGLIANDO DI GARANZIA
GARANTIEKAART
TARJETA DE GARANTÍA
CARTÃO DE GARANTIA
GARANTIBEVIS
GARANTI KORT
GARANTI KORT
TAKUUKORTTI
∫∞ƒ∆∞ E°°À∏™∏™
Español Después de haber comprado su herramienta envíe
usted, por favor, esta tarjeta a la central de
Black & Decker en su país.
Português Por favor, recorte esta parte, coloque-a num envelope
selado e endereçado e envie-o logo após a compra do
seu produto para o endereço da Black & Decker do
seu país.
Svenska Var vänlig klipp ur denna del och sänd den i ett frankerat
kuvert till Black & Deckers adress i Ditt land.
Norsk Vennligst klipp ut denne delen umiddelbart etter du
har pakket ut ditt produkt og legg det i en adressert
konvolutt til Black & Decker (Norge) A/S.
Dansk Venligst klip denne del ud og send frankeret til
Black & Decker i dit land.
Suomi Leikkaa irti tämä osa, laita se kuoreen ja postita kuori
paikalliseen Black & Decker osoitteeseen.
EÏÏËÓÈη ¶·Ú·Î·ÏÒ Îfi„ÂÙ ·˘Ùfi ÙÔ ÎÔÌÌ¿ÙÈ Î·È Ù·¯˘‰ÚÔÌ‹Û·ÙÂ
ÙÔ ·Ì¤Ûˆ˜ ÌÂÙ¿ ÙËÓ ·ÁÔÚ¿ ÙÔ˘ ÚÔ˚fiÓÙÔ˜ Û·˜ ÛÙËÓ
‰È‡ı˘ÓÛË Ù˘ Black & Decker ÛÙËÓ EÏÏ¿‰·.
English Please complete this section immediately after the
purchase of your tool and send it to Black & Decker in
your country. If you live in Australia or New Zealand,
please register by using the alternative guarantee card
supplied.
Deutsch Bitte schneiden Sie diesen Abschnitt ab, stecken ihn in
einen frankierten Umschlag und schicken ihn an die
Black & Decker Adresse Ihres Landes.
Français Découpez cette partie et envoyez-la sous enveloppe
timbrée à l’adresse de Black & Decker dans votre pays,
ceci immédiatement après votre achat.
Italiano Per favore ritagliate questa parte, inseritela in una
busta con francobollo e speditela subito dopo
l’acquisto del prodotto all’indirizzo della
Black & Decker nella vostra nazione.
Nederlands Knip dit gedeelte uit en zend het direct na aankoop in
een gefrankeerde, geadresseerde envelop naar het
adres van Black & Decker in uw land.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

BLACK+DECKER KS890E User manual

Category
Power tools
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI