33
Installation & Maintenance
English
Installation
This information is exclusively for the installer
who is responsible for assembly and electrical
connection. The manufacturer will not accept
liability for possible damage caused if you install
the oven yourself.
BEFOREīINSTALLATION
ā¢ī Toī handleī theī oven,ī useī theī gripsī atī theī
sides. Do not use the door handle to lift the
oven.
ā¢ī Doī notī installī theī ovenī behindī decorativeī
doors. This can cause it to overheat.
ā¢ī Whenī installingī theī ovenī underī aī counter,ī
follow the instructions for installing it.
ā¢ī Inīgeneral,īprotrudingīelementsī(furnitureīre-
inforcements,īpipes,īsocketībases,īetc.)īatī
the back of the unit must be avoided.
ā¢ī Whenītheībaseīofītheīmainīpowerīsocketīisī
insideītheīunitīinīwhichītheīovenīisīinstalled,ī
this must be done in the shaded area.
Figure 2.
ā¢ī Theīunitīinīwhichītheīovenīisīinstalledīandī
adjacent units must withstand temperatures
higher than 85 ĀŗC.
ā¢ī Theī installationī instructionsī mustī beī ad-
heredītoīstrictly.īIfīnot,ītheīovenāsīventilationī
circuitīmayī becomeī blocked,ī causingī highī
temperatures that could damage the kitchen
unit and the appliance itself.
ā¢ī Forī thisī purpose,ī checkī theī unitī measure-
ments and those of the holes to be drilled in
theīunits,īasīshownīinītheīfollowingīī·gures:
Column installation.
60īcmīoven:īFigureī7*.
45īcmīoven:īFigureī8*.
ī CAUTION
*īWhenīinstallingīpyrolyticīovens,īDOīNOT
drill any holes in the unit inside the shaded
areas.
Undercounter installation.
60īcmīoven:īFigureī9*.
45īcmīoven:īFigureī10*.
ī WARNING
*īWhenīinstallingīpyrolyticīovens,īDOīNOT
drill any holes in the unit inside the shaded
areas.
ELECTRICALīCONNECTION
Theīī·tterīmustīensureīthat:
ā¢ī Theī mainsī powerī voltageī andī frequencyī
correspond to what is marked on the identi-
ī·cationīplate.
ā¢ī Theīdomesticīwiringīsystemīcanīwithstandī
theīmaximumīpowerīmarkedīonītheīidentiī·-
cation plate.
ā¢ī Afterī connectingī theī powerī supply,ī checkī
that all electrical parts of the oven are work-
ing correctly.
OVENīINSTALLATION
For all ovens. After the electrical connection has
beenīdone:
1. Position the oven inside the unit and ensure
that the feed cable is not trapped or in con-
tact with parts of the oven that heat up.
2. Make sure that the body of the oven is not
in contact with the walls of the unit and that
there is a minimum space of 2 mm between
adjacent units.
3. Centre the oven in the unit so that there is a
minimum space of 5mm between the oven
and the doors of the furniture that surrounds
it. Figure 3.
4. Open the door and insert the plastic plugs
supplied with the oven into their respective
housings. Figure 11.
5. Fasten the oven to the unit with the screws
supplied,ī screwingī themī intoī theī unitī
through the stops.