Grizzly T1233 Owner's manual

Brand: Grizzly

Model: T1233

Category: Soldering irons

Type: Owner's manual

Grizzly T1233 High-Speed Soldering Gun is a professional-grade tool designed for fast and efficient soldering tasks. It features a comfortable pistol grip and a built-in light to illuminate your work area. The soldering gun heats up in just 15 seconds, reaching temperatures between 842ºF–1022ºF. It comes with a tube of coiled solder and a cup of flux to get you started. The quick tip replacement system makes it easy to change tips for different soldering applications.

Here are some of the capabilities of the Grizzly T1233 High-Speed Soldering Gun:

• Fast heating: Heats up in just 15 seconds • High temperature: Reaches temperatures between 842ºF–1022ºF

Here are some of the capabilities of the Grizzly T1233 High-Speed Soldering Gun:

• Fast heating: Heats up in just 15 seconds • High temperature: Reaches temperatures between 842ºF–1022ºF

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T1233

HIGH-SPEED

SOLDERING GUN

INSTRUCTIONS

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#ES19033 PRINTED IN CHINA

Introduction

The Model T1233 High-Speed Soldering Gun

is for professional use. This fast-heating solder-

ing gun features a comfortable pistol grip and is

designed for quick tip replacement. It also incudes

a built-in light to better illuminate your workpiece.

V1.08.17

Specifications

Power Requirement . . 120V, Single-Phase, 60 Hz

Full-Load Amp Draw ........................................ 1A

Minimum Circuit Size ..................................... 15A

Temperature Range ...................... 842ºF–1022ºF

Time to Maximum Temperature ........15 seconds

Cord ............................................................... 6 ft.

Weight ...................................................1-1/2 lbs.

Inventory

Description Qty

A. High-Speed Soldering Gun w/Tip .............. 1

B. Replacement Tip ........................................ 1

C. Tube of Coiled Solder ................................. 1

D. Cup of Flux ................................................ 1

Figure 1. Model T1233 High-Speed Soldering

Gun.

To reduce risk of serious personal injury:

• Avoid inhaling toxic fumes. Toxic chemicals

in some solders and flux can cause respira-

tory illness when inhaled. Work in well ven-

tilated area with fan to move air, and w

ear

NIOSH-approved respirator.

• Bandage cuts or sores before soldering.

Toxins can be absorbed through cuts, sores,

eyes, mouth and nostrils, increasing risk of

developing certain diseases. DO NOT eat,

drink, or smoke while soldering. Wash your

hands with soap and water when finished.

• Wear eye protection, gloves, long pants,

and a long sleeve shirt to protect eyes

and hands from burns and skin rashes.

Soldering tip will reach temperatures up to

1022º F. DO NOT touch soldering tip until it

has completely cooled.

• Use soldering work stand, hold part with

pliers, or use a heat sink when working with

small parts. Workpieces can heat up and

cause burns.

• DO NOT leave soldering gun unattended

or allow soldering tip to rest against any

thing. Tool can ignite explosive or flam-

mable materials nearby. Move these materi-

als a safe distance away. Always keep a fire

extinguisher on hand.

• Disconnect from power before working on

circuits or wiring to reduce risk of electrocu-

tion.

•

Use tool for intended purpose. Never mod-

ify, alter, or use tool for a purpose not

intended by manufacturer or serious injury

or death may result!

• Keep out of reach of children.

-2-

T1233 High-Speed Soldering Gun (Mfd. 08/17)

PARTS STORE

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

Parts Breakdown & List

1. Clean surfaces of material to be soldered

together to ensure proper bonding. Use steel

wool or fine grit sandpaper to clean soldering

tip.

2. Insert polarized plug into matching 120V

power receptacle and pull trigger for 10-15

seconds to allow soldering tip to heat up.

Note: For every minute of use, allow gun to

cool four minutes. Holding trigger continu-

ously for over one minute will cause gun to

overheat and shorten its lifespan.

3. Apply a small amount of rosin-core solder

to soldering tip. Allow solder to form a thin

film over soldering tip, then wipe tip with wet

sponge to remove excess solder.

4. Prepare workpieces to be soldered by brush-

ing on flux if using non-rosin core solder.

5. Pull trigger to heat both workpieces equally

by touching the soldering tip to each for a few

seconds.

Operation

6. Feed solder into joint, NOT soldering tip.

Solder will melt and flow into and around all

the parts and areas that are above melting

point.

7. Remove solder, then remove soldering tip.

Note: Insufficient solder on soldering tip

causes poor heat transfer to joint, resulting

in weak mechanical and electrical bond.

Too much solder results in strings of solder,

causing bridges to other contacts. A good

soldered joint should be smooth, shiny, and

completely surround the joint.

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT1233001 HOUSING (RIGHT) 10 PT1233010 LIGHT BULB 6V 3W

2 PT1233002 HOUSING (LEFT) 11 PT1233011 LIGHT BULB COVER

3 PT1233003 TAP SCREW M4 X 14 12 PT1233012 TRANSFORMER

4 PT1233004 TAP SCREW M4 X 24 13 PT1233013 COLLET ROD

5 PT1233005 POWER CORD 2W 18AWG 72" 1-15P 14 PT1233014 COLLET ROD SLEEVE

6 PT1233006 STRAIN RELIEF 3/8" TYPE-1 15 PT1233015 KNURLED TIP NUT

7 PT1233007 ON/OFF SWITCH DONGNAN KW4A 125V 16 PT1233016 SOLDER TIP

8 PT1233008 TRIGGER (PLASTIC) 17 PT1233017 FLUX CUP

9 PT1233009 LIGHT BULB HOUSING 18 PT1233018 SOLDER TUBE

1. Unplug soldering gun and wait until soldering

tip has completely cooled.

2. Loosen knurled tip nuts securing soldering

tip, and pull to remove it.

3. Slide in replacement soldering tip and tighten

knurled tip nuts.

Replacing Tips

Grizzly T1233 Owner's manual

Brand: Grizzly

Model: T1233

Category: Soldering irons

Type: Owner's manual

Here are some of the capabilities of the Grizzly T1233 High-Speed Soldering Gun:

• Fast heating: Heats up in just 15 seconds • High temperature: Reaches temperatures between 842ºF–1022ºF

Download PDF

report

Grizzly T1233 Owner's manual

Grizzly T1233 Owner's manual

Related papers

Other documents