Edelbrock Edelbrock Cooling System Upgrade Kit #15804 For 2005-06 Ford Mustang GT Installation guide

Edelbrock
Brand
Edelbrock
Model
Edelbrock Cooling System Upgrade Kit #15804 For 2005-06 Ford Mustang GT
Type
Installation guide

This manual is also suitable for

Edelbrock Cooling System Upgrade Kit #15804 For 2005-06 Ford Mustang GT

Edelbrock Cooling System Upgrade Kit #15804 is designed to provide your 2005-06 Ford Mustang GT with the necessary cooling upgrades to support the installation of an Edelbrock E-Force Supercharger. This kit features reinforced components and optimized coolant flow to ensure that your engine remains cool even under the increased demands of forced induction.

Key Features:

  • Includes all necessary hardware for a complete cooling system upgrade
  • Reinforced components for increased durability
  • Optimized coolant flow for improved cooling efficiency

Edelbrock Cooling System Upgrade Kit #15804 For 2005-06 Ford Mustang GT

Edelbrock Cooling System Upgrade Kit #15804 is designed to provide your 2005-06 Ford Mustang GT with the necessary cooling upgrades to support the installation of an Edelbrock E-Force Supercharger. This kit features reinforced components and optimized coolant flow to ensure that your engine remains cool even under the increased demands of forced induction.

Key Features:

  • Includes all necessary hardware for a complete cooling system upgrade
  • Reinforced components for increased durability
  • Optimized coolant flow for improved cooling efficiency
EDELBROCK E-FORCE SUPERCHARGER
SUPPLEMENTAL HARDWARE KIT
For use with the 4.6L Ford E-Force Supercharger
Part #15804
Please study these instructions carefully before installing your new supercharger. If you have any questions, do not hesitate to
contact our Technical Hotline at: (800) 416-8628 from 7:00 am to 5:00 pm, Monday through Friday, Pacific Standard Time.
DESCRIPTION: This kit includes supplemental hardware for installing the #1580/#1585 E-Force Supercharger Systems on 2005 &
2006 model year Mustangs. These components are required for installation and should be purchased before beginning the
supercharger installation.
KIT CONTENTS:
©2010 Edelbrock Corporation
Brochure #63-15804
Part #15804
Rev. 3/10 - AJ/mc
INSTALLATION: Vehicles that require the #15804 kit should
refer to the cooling system portion of the #1580/#1585
Installation Instructions for the proper installation procedure for
the thermostat and related components. The steps listed below
detail the procedure for removing the hydrocarbon trap from the
factory air tube and installing it in the silicone elbow supplied
with the E-Force Supercharger. This procedure is required to
maintain compliance with the California Air Resources Board
Executive Order that authorizes installation of the #1580 kit on
pollution controlled vehicles.
1. Remove the hydrocarbon trap from the factory air tube (Fig 1).
The easiest way to do this is to carefully cut the air tube and
remove the trap. If you would prefer to keep the air tube intact,
it is possible to use one or more flathead screwdrivers to pry the
inside lip of the air tube away from the carbon trap (Fig 2), then
use a pair of needle nose pliers to grab the metal housing of the
trap and work it back and forth to separate it from the tube.
2. Once the trap has been removed from the factory air tube,
press it into the short silicone tube supplied with the #15804 kit
until both edges are flush (Fig 3).
3. Spray the inside of the silicone elbow supplied with the
#1580 supercharger system with silicone spray to facilitate
installation then push the hydrocarbon trap into the elbow (Fig
4). Continue pushing the trap into the elbow until there is a gap
of roughly 1/2” from the end to the trap.
4. Secure the location of the carbon trap by installing and
tightening the supplied hose clamp around the silicone tube
where the trap is located (Fig 5). The silicone elbow can now be
installed as described in step #154 of the #1580/#1585
Installation Instructions.
Quantity Description
1 4.0” Worm Drive Hose Clamp
1 Thermostat Housing
1 Thermostat
1 3.0” I.D. Black Silicone Hose
1 Lower Coolant Hose Assembly
1 Upper Radiator Hose
1 M6 x 1.0 Nylok Nut
1 Throttle Position Sensor
Fig 1
Fig 2
Fig 3
Fig 4
Fig 5
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503
Tech-Line: 1-800-416-8628 • Sales/Office (310) 781-2222
  • Page 1 1

Edelbrock Edelbrock Cooling System Upgrade Kit #15804 For 2005-06 Ford Mustang GT Installation guide

Edelbrock
Brand
Edelbrock
Model
Edelbrock Cooling System Upgrade Kit #15804 For 2005-06 Ford Mustang GT
Type
Installation guide
This manual is also suitable for

Edelbrock Cooling System Upgrade Kit #15804 For 2005-06 Ford Mustang GT

Edelbrock Cooling System Upgrade Kit #15804 is designed to provide your 2005-06 Ford Mustang GT with the necessary cooling upgrades to support the installation of an Edelbrock E-Force Supercharger. This kit features reinforced components and optimized coolant flow to ensure that your engine remains cool even under the increased demands of forced induction.

Key Features:

  • Includes all necessary hardware for a complete cooling system upgrade
  • Reinforced components for increased durability
  • Optimized coolant flow for improved cooling efficiency
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers