Whirlpool FA3S 841 P IX A AUS Setup and user guide

Brand: Whirlpool

Model: FA3S 841 P IX A AUS

Type: Setup and user guide

DAILY REFERENCE

GUIDE

THANK YOU FOR PURCHASING AN

ARISTON PRODUCT

To receive more comprehensive help and

support, please register your product at

www. aristonchannel. com

WWW

You can download the Safety Instructions

and the Use and Care Guide by visiting our

website www. aristonchannel. com and

following the instructions on the back of

this booklet.

Before using the appliance carefully read the Health and Safety guide.

PRODUCT DESCRIPTION

1. Control panel

2. Fan

3. Lamp

4. Shelf guides (the level is

indicated on the wall of the

cooking compartment)

5. Door

6. Door lock (locks the door while

automatic cleaning is in progress

and afterwards)

7. Upper heating element/grill

8. Circular heating element (not

visible)

9. Identification plate (do not

remove)

10.

embossing for

drinking water

CONTROL PANEL DESCRIPTION

1 32 4 5

1. SELECTION KNOB

For switching the oven on by

selecting a function. Turn to the

position to switch the oven off.

2. LIGHT

With the oven switched on, press

to turn the oven compartment

lamp on or off.

3. SETTING THE TIME

For accessing the cooking time

settings, delayed start and timer.

For displaying the time when the

oven is off.

4. DISPLAY

5. ADJUSTMENT BUTTONS

For changing the cooking time

settings.

6. THERMOSTAT KNOB

Turn to select the temperature you

require when activating manual

functions.

ACCESSORIES

WIRE SHELF DRIP TRAY * BAKING TRAY * SLIDING RUNNERS *

Use to cook food or as a

support for pans, cake tins

and other ovenproof items of

cookware.

Use as an oven tray for

cooking meat, sh,

vegetables, focaccia, etc. or

position underneath the wire

shelf to collect cooking juices.

Use for cooking all bread and

pastry products, but also for

roasts, sh en papillotte, etc.

To facilitate inserting or

removing accessories.

* Availble only on certain models

The number and the type of accessories may vary depending on which model is purchased.

Other accessories can be purchased separately from the After-sales Service.

INSERTING THE WIRE SHELF AND OTHER

ACCESSORIES

. Insert the wire shelf onto the level you require by

holding it tilted slightly upwards and resting the

raised rear side (pointing upwards) down first.

Then slide it horizontally along the runners as far as

possible.

. Other accessories, like the baking tray, are to be

inserted horizontally, letting them slide on the

runners.

REMOVING AND REFITTING THE SHELF GUIDES

. To remove the shelf guides, firmly grip the external

part of the guide, and pull it towards you to extract

the support and the two internal pins from the

lodging.

. To reposition the shelf guides, position them near

the cavity and initially insert the two pins into their

lodgings. Next, position the external part near its

lodging, insert the support, and firmly press towards

the wall of the cavity to make sure the shelf guide is

properly secured.

FITTING THE SLIDING RUNNERS IF PRESENT

Remove the shelf guides. Disengage the guide’s

anchoring clips from the shelf guide, starting from

the lower part.

To reinstall the sliding guides, anchor theguide’s

upper clip to the shelf guide, then lower the other

clip into position. To secure the guide, press the

lower portion of the clip firmly against the shelf

guide. Make sure that the runners can move freely.

Reposition the shelf guides.

Please note: The sliding runners can be tted on any level.

FUNCTIONS

CONVENTIONAL

For cooking any kind of dish on one shelf only.

FORCED AIR

For cooking different foods that require the

same cooking temperature on several shelves

(maximum three) at the same time. This function can

be used to cook different foods without odours being

transferred from one food to another.

PIZZA

For baking different types and sizes of pizza and

bread. It is a good idea to swap the position of the

baking trays halfway through cooking.

GRILL

For grilling steaks, kebabs and sausages,

cooking vegetables au gratin or toasting bread.

When grilling meat, we recommend using a dripping

pan to collect the cooking juices: position the pan on

any of the levels below the wire shelf and add 200 ml

of drinking water.

TURBO GRILL

For roasting large joints of meat (legs, roast

beef, chicken). We recommend using a dripping pan

to collect the cooking juices: position the pan on any

of the levels below the wire shelf and add 200 ml of

drinking water.

RISING

For helping sweet or savoury dough to rise

effectively. Turn the thermostat knob to the icon to

activate this function.

ECO FORCED AIR

For cooking roasts and stuffed roasting joints

on a single shelf. Food is prevented from drying out

excessively by gentle, intermittent air circulation.

When this ECO function is in use, the light will remain

switched off during cooking but can be switched on

again by pressing

AUTOMATIC CLEANING - PYRO

For eliminating cooking spatters using a cycle

at very high temperature (over 400 °C).

• FISH

• MEAT

• BREAD

The functions provide excellent results

thanks to the addition of steam in cooking cycles.

Only when the oven is cold, pour drinking water

on the bottom of the oven and select the specific

function for your preparation. The optimal water

quantities and temperatures for each food category

are listed in the relative cooking table. Do not

preheat the oven before inserting food.

FIRST TIME USE

1. SETTING THE TIME

You will need to set the time when you switch on the

appliance for the first time: Press

until the icon

and the two digits for the hour start flashing on the

display.

Use or to set the hour and press to confirm.

The two digits for the minutes will start flashing. Use

or to set the minutes and press to confirm.

Please note: When the icon is ashing, for example

following lengthy power outages, you will need to reset the

time.

2. SET THE POWER CONSUMPTION

The oven is programmed to work at a power of less

than 2.9 kW (“Lo”): To operate the oven at a power

that is compatible with a domestic power supply of

greater than 3 kW (“Hi”), you will need to change the

settings.

To go to the change menu, turn the selection knob to

, then turn it back to .

Press and hold and for five seconds immediately

afterwards.

Use o to change the setting, then press and hold

for at least two seconds to confirm.

3. HEAT THE OVEN

A new oven may release odours that have been left

behind during manufacturing: this is completely

normal.

Before starting to cook food, we therefore

recommend heating the oven with it empty in order

to remove any possible odours.

Remove any protective cardboard or transparent

film from the oven and remove any accessories from

inside it.

Heat the oven to 250 °C for about one hour. The oven

must be empty during this time.

Please note: It is advisable to air the room after using the

appliance for the rst time.

DAILY USE

1. SELECT A FUNCTION

To select a function, turn the selection knob to the

symbol for the function you require: the display will

light up and an audible signal will sound.

2. ACTIVATE A FUNCTION

MANUAL

To start the function you have selected, turn the

thermostat knob to set the temperature you require.

Please note: During cooking you can change the function by

turning the selection knob or adjust the temperature by

turning the thermostat knob. The function will not start if the

thermostat knob will be on

. You can set the cooking time,

cooking end time (only if you set a cooking time) and a timer.

RISING

To start the “Rising” function, turn the thermostat

knob to the relevant symbol; if the oven is set to a

different temperature, the function will not start.

Please note: You can set the cooking time, cooking end time

(only if you set a cooking time) and a timer.

Only when the oven is cold, fill

the embossing of the cavity with

the quantity of drinking water

suggested in the relative cooking

table. Place the food in the oven.

Set and activate the

function: At the end, carefully

open the door and let steam

escape slowly.

Please note: During steam cooking, do not open the door and

never top up the water.

3. PREHEATING AND RESIDUAL HEAT

Once the function starts, an audible signal and a

flashing icon

on the display indicate that the

preheating phase is active.

When the set temperature has been reached, the icon

becomes fixed and a new audible signal will sound

to indicate that the food can be placed inside and

cooking can proceed.

Please note: Placing food in the oven before the preheating

phase has nished may have an adverse eect on the nal

result of cooking.

After cooking and with the function deactivated, the

icon

may continue to remain visible on the display

even after the cooling fan has switched off to indicate

that there is residual heat in the compartment.

Please note: The time after which the icon switches o varies

because it depends on a series of factors such as ambient

temperature and function used. In any case, the product

should be considered to be o when the pointer on the

selection knob is at “

”.

. PROGRAMMING COOKING

You will need to select a function before you can start

programming cooking.

DURATION

Keep pressing until the icon and “00:00” start

flashing on the display.

Use or to set the cooking time you require, then

press

to confirm.

Activate the function by turning the thermostat knob

to the temperature you require: an audible signal will

sound and the display will indicate that cooking is

complete.

Please note: To cancel the cooking time you have set, keep

pressing until the icon starts flashing on the display,

then use to reset the cooking time to “00:00”. This

cooking time includes a preheating phase.

PROGRAMMING THE END COOKING TIME/

DELAYED START

After a cooking time has been set, starting the

function can be delayed by programming its end

time: press

until the icon and the current time

start flashing on the display.

Use or to set the time you want cooking to end

and press

to confirm.

Activate the function by turning the thermostat

knob to the temperature you require: the function

will remain paused until it starts automatically after

the period of time that has been calculated in order

forcooking to finish at the time you have set.

Please note: To cancel the setting, switch the oven off by

turning the selection knob to the position.

END OF COOKING

An audible signal will sound and the display will

indicate that the function has finished.

Turn the selection knob to select a different function

or to

to switch the oven off.

Please note: If the timer is active, the display will show “END”

alternately with the remaining time.

. SETTING THE TIMER

This option does not interrupt or program cooking

but allows you to use the display as a timer, either

during while a function is active or when the oven is

off.

Keep pressing

until the and “00:00” icon and

“00:00” start flashing on the display.

Use or to set the time you require and press

to confirm. An audible signal will sound once the

timer has finished counting down the selected time.

Notes: To cancel the timer, keep pressing until the icon

starts ashing, then use

to reset the time to “00:00”.

. AUTOMATIC CLEANING FUNCTION – PYRO

Do not touch the oven during the Pyro cycle.

Keep children and animals away from the oven

during and after (until the room has finished

airing) running the Pyro cycle.

Remove all accessories - including shelf guides - from

the oven before activating the function. If the oven is

installed below a hob, make sure that all the burners

or electric hotplates are switched off while running

the selfcleaning cycle.

For optimum cleaning results, remove the worst

soiling with a damp sponge before using the Pyro

function.

Avoid activating the pyro cycle cleaning in the

presence of limescale residues.

We recommend only running the Pyro function if

the appliance contains heavy soiling or gives off bad

odours during cooking.

To activate the automatic cleaning function, turn the

selection knob and the thermostat knob to the

icon.

The function will be activated automatically, the door

locked and the light inside the oven switched off:

The display will show the time remaining to the end,

alternating with “Piro”.

Once the cycle has been completed, the door remains

locked until the temperature inside the oven has

returned to a safe level. Air the room during and after

running the Pyro cycle.

COOKING TABLE

RECIPE FUNCTION PREHEAT TEMPERATURE (°C) DURATION (Min) LEVEL AND ACCESSORIES

Leavened cakes

Yes 170 30 - 50

Yes 160 30 - 50

Yes 160 40 - 60

Filled cake

(cheese cake, strudel, fruit pie)

Yes 160 - 200 35 - 90

Yes 160 - 200 40 - 90

Biscuits / tartlets

Yes 160 25 - 35

Yes 150 35 - 45

Choux buns

Yes 180 - 210 30 - 40

Yes 180 - 200 35 - 45

3 1

Meringues

Yes 90 150 - 200

Yes 90 140 - 200

3 1

Pizza / Focaccia

Yes 190 - 250 15 - 50

1 / 2

Yes 190 - 250 20 - 50

Frozen pizza

Yes 250 10 - 20

Yes 230-250 10 - 25

Salty cakes

(vegetable pie, quiche)

Yes 180 - 200 40 - 55

Yes 180 - 200 45 - 60

3 1

Vols-au-vents / puff pastry crackers

Yes 190 - 200 20 - 30

Yes 180 - 190 20 - 40

3 1

Lasagne / baked pasta /

canneloni / flans

Yes 190 - 200 45 - 65

Lamb / veal / beef / pork 1 kg Yes 190 - 200 80 - 110

Roast pork with crackling 2 kg Yes 180 - 190 110 - 150

Chicken / rabbit / duck 1 kg Yes 200 - 230 50 - 100

Turkey / goose 3 kg - 190 - 200 100 - 160

Baked fish / en papillote

(fillets, whole)

Yes 170 - 190 30 - 45

Stuffed vegetables

(tomatoes, courgettes, aubergines)

Yes 180 - 200 50 - 70

FUNCTIONS

Conventional Forced Air Pizza Grill Turbo Grill Eco Forced Air

ACCESSORIES

Wire shelf

Baking dish or cake tin

on the wire shelf

Baking tray/Drip tray or

Baking dish on the wire shelf

Drip tray / Baking tray

Drip tray / Baking tray with

200 ml of water

RECIPE FUNCTION PREHEAT TEMPERATURE (°C) DURATION (Min) LEVEL AND ACCESSORIES

Toasted bread 5' 250 2 - 6

Fish fillets / slices - 230 - 250 15 - 30 *

Sausages / kebabs /

spare ribs / hamburgers

- 250 15 - 30 *

Roast chicken 1-1.3 kg Yes 200 - 220 55 - 70 **

Roast beef rare 1 kg Yes 200 - 210 35 - 50 **

Leg of lamb / knuckle Yes 200 - 210 60 - 90 **

Roast potatoes Yes 200 - 210 35 - 55

Vegetable gratin - 200 - 210 25 - 55

Meat and potatoes Yes 190 - 200 45 - 100 ***

Fish and vegetables Yes 180 30 - 50 ***

Lasagne and meat Yes 200 50 - 100 ***

Complete meal: fruit tart (level 5) /

lasagne (level 3) / meat (level 1)

Yes 180 - 190 40 - 120 ***

3 1

Roast meat / stuffed roasting joints - 170 - 180 100 - 150

* Turn food halfway through cooking

** Turn food two thirds of the way through cooking (if

necessary).

*** Estimated length of time: dishes can be removed from the

oven at dierent times depending on personal preference.

RECIPE FUNCTION

WATER (ml)

PREHEAT

TEMPERATURE (°C) DURATION (Min)

LEVEL AND

ACCESSORIES

Fish fillets / cutlets 0.5 - 2 cm

250 - 190 - 210 15 - 25

Whole fish 300 - 600 g

250 - 190 - 210 15 - 30

Whole fish 600 g - 1.2 kg

250 - 180 - 200 25 - 45

Roast Beef rare 1 kg

250 - 190 - 210 40 - 55

Lamb shank 500 g - 1.5 kg

250 - 170 - 190 60 - 75

Chicken / guinea fowl / duck

Whole 1 - 1.5 kg

250 - 200 - 220 55 - 75

Chicken / guinea fowl / duck

Pieces 500 g - 1.5 kg

250 - 200 - 220 40 - 60

Chicken / turkey / duck

Whole 3 kg

250 - 160 - 180 100 - 140

Lamb / Beef / Pork 1 kg

250 - 170 - 190 60 - 100

Small bread 80 - 100 g

200 - 200 - 220 30 - 45

Sandwich loaf in tin 300 - 500 g

250 - 170 - 190 45 - 60

Bread loaf 500 g - 2 kg

250 - 160 - 170 50 - 100

Baguettes 200 - 300 g

250 - 200 - 220 30 - 45

The time indicated includes the preheating phase: we recommend placing the food in the oven and setting

the cooking time when starting the function.

FUNCTIONS

Conventional Forced Air Pizza Grill Turbo Grill Eco Forced Air Fish Meat Bread

ACCESSORIES

Wire shelf

Baking dish or cake tin

on the wire shelf

Baking tray/Drip tray or

Baking dish on the wire shelf

Drip tray / Baking tray

Drip tray / Baking tray with

200 ml of water

CLEANING AND MAINTENANCE

Make sure that the oven has

cooled down before carrying out

any maintenance or cleaning.

Do not use steam cleaners.

Do not use wire wool, abrasive

scourers or abrasive/corrosive

cleaning agents, as these could

damage the surfaces of the

appliance.

Wear protective gloves.

The oven must be disconnected

from the mains before carrying

out any kind of maintenance

work.

EXTERIOR SURFACES

Clean the surfaces with a damp microfibre cloth. If

they are very dirty, add a few drops of pH-neutral

detergent. Finish off with a dry cloth.

Do not use corrosive or abrasive detergents. If any of

these products inadvertently comes into contact with

the surfaces of the appliance, clean immediately with

a damp microfibre cloth.

INTERIOR SURFACES

• After every use, leave the oven to cool and then

clean it, preferably while it is still warm, to remove

any deposits or stains caused by food residues. To

dry any condensation that has formed as a result of

cooking foods with a high water content, leave the

oven to cool completely and then wipe it with a cloth

or sponge.

• To remove the remaining limescale from the bottom

of the cavity after the

cooking, just pour 250

ml of white vinegar onto the embossing of the cavity

(alternatively, use a specific descaling product. For

availability please contact the After Sales Service).

Leave it to work at room temperature for 30 minutes,

then clean the cavity with warm drinking water and a

soft cloth. Cleaning is recommended at least for every

5 to 10

cooking cycles.

• If there is stubborn dirt on the interior surfaces, we

recommend running the automatic cleaning function

for optimal cleaning results. Avoid activating the

pyrolitic cycle cleaning in the presence of limescale

residues. Before activating, perform limescale

cleaning as described above.

• The door can be easily removed and refitted to

facilitate cleaning of the glass.

• Clean the glass in the door with a suitable liquid

detergent.

ACCESSORIES

Soak the accessories in a washing-up liquid solution

after use, handling them with oven gloves if they

are still hot. Food residues can be removed using a

washing-up brush or a sponge.

REMOVING AND REFITTING THE DOOR

. To remove the door, open

it fully and lower the

catches until they are in the

unlock position.

~15°

2. Close the door as much

as you can. Take a firm hold

of the door with both hands

– do not hold it by the

handle. Simply remove the

door by continuing to close

it while pulling it upwards

at the same time until it is

released from its seating. Put the door to one side,

resting it on a soft surface.

3. Refit the door by moving it towards the oven,

aligning the hooks of the hinges with their seating

and securing the upper part onto its seating.

4. Lower the door and then

open it fully. Lower the

catches into their original

position: Make sure that

you lower them down

completely.

Apply gentle pressure to check that the catches are in

the correct position.

5. Try closing the door and check to make sure that it

lines up with the control panel. If it does not, repeat

the steps above: The door could become damaged if

it does not work properly.

REPLACING THE LAMP

1. Disconnect the oven from the power supply.

2. Unscrew the cover from the light, replace the bulb

and screw the cover back on the light.

3. Reconnect the oven to the power supply.

Please note: Use 25 W/230 V type G9, T300 °C halogen lamps.

The bulb used in the product is specically designed for

domestic appliances and is not suitable for general room

lighting within the home (EC Regulation 244/2009).

Light bulbs are available from our After-sales Service. - Do not

handle bulbs with your bare hands as your ngerprints could

damage them. Do not use the oven until the light cover has

been retted.

CLICK & CLEAN - CLEANING THE GLASSES

1. After removing the door and resting it on a soft

surface with the handle downwards, simultaneously

press the two retaining clips and remove the upper

edge of the door by pulling it towards you.

2. Lift and firmly hold the inner glass with both

hands, remove it and place it on a soft surface before

cleaning it.

3. Refit the intermediate pane (marked with “1R”)

before refitting the inside pane: To position the panes

of glass correctly, make sure that the “R” mark can be

seen in the left-hand corner. First insert the long side

of the glass marked “R” into the support seats, then

lower it into position. Repeat this procedure for both

panes of glass.

4. Refit the upper edge: A click will indicate correct

positioning. Make sure the seal is secure before

refitting the door.

TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE SOLUTION

The oven is not working.

Power cut.

Disconnection from the mains.

Check for the presence of mains electrical power and whether

the oven is connected to the electricity supply.

Turn off the oven and restart it to see if the fault persists.

The display shows the letter “F”

followed by a number or letter.

Oven failure.

Contact you nearest Client After-sales Service Centre and state

the number following the letter “F”.

The display is showing the

message “Hot” and the selected

function will not start.

Temperature too high.

Allow the oven to cool down before activating the function.

Select a different function.

PRODUCT FICHE

WWW

The product fiche with energy data of this

appliance can be downloaded from the website

www. aristonchannel. com

HOW TO OBTAIN THE USE AND CARE GUIDE

WWW

Download the Use and Care Guide

from our website www. aristonchannel. com

(you can use this QR Code), specifying the

product’s commercial code.

> Alternatively, contact our Client After-sales Service.

CONTACTING OUR AFTER-SALES SERVICE

You can find our

contact details in the

warranty manual. When

contacting our Client

After-sales Service,

please state the codes

provided on your

product's identification plate.

Model: xxxXXXXxx

XXXXXX XXXXXX XXXXX XXXXXXX

400011345609

Printed in Italy

Whirlpool FA3S 841 P IX A AUS Setup and user guide

Whirlpool FA3S 841 P IX A AUS Setup and user guide

Whirlpool FA3S 841 P IX A AUS Setup and user guide

Related papers

Other documents