DIP-A-LAIT
INSTALLATION OPERATION AND CARE OF
DIP-A-LAIT
MODEL: DLA0002 R01/DLA0002-120 R01
NB:
REGISTER ON-LINE TODAY
Register your warranty on-line now at www.anvilworld.com
NO WEB ACCESS
If you do not have access to the Web. Kindly register by completing
the warranty registration form and fax it to the ANVIL oce in the
country of purchase.
Failure to do so will invalidate your warranty.
4-INS-DLA0002R01
LIMITED WARRANTY
All equipment which is sold under ANVIL trademark and used for
commercial purposes is warranted against defects in materials and
workmanship. The warranty runs for two years from the date of
original installation and is for the benet of the original purchaser
only. All other Warranties, expressed or implied, statutory or
otherwise, including without limitations any implied Warranty of
Merchantability or tness for purpose are excluded. The Seller shall
in no event be liable for direct,indirect or consequential damages in
connection with ANVIL commercial products.
The Sellers obligation under this Warranty is limited to the
repair of defects without charge. Defective units must be taken or
shipped, transportation charges prepaid, to ANVIL.
This Warranty is not eective if damage occurs because of accident,
carelessness, improper installation, lack of proper
set-up,supervision when required or if the equipment is installed or
operated in any manner contrary to the installation and
operating instructions. In these cases,repairs will be made at a
reasonable cost. Work performed by unauthorized personnel or
unauthorized service agencies using non Anvil spares voids this
Warranty.
THESE INSTRUCTIONS MUST BE FOLLOWED FOR US TO
GUARANTEE OUR FULL SUPPORT OF YOUR CLAIM FOR
PROTECTING AGAINST LOSS FROM CONCEALED DAMAGE.
THE FORM FOR FILING SUCH A CLAIM WILL BE PROVIDED
BY THE CARRIER.
UNPACKING
Unpack the product and check for any damage incurred during
transit. This should be reported to the responsible carrier, railway or
postal authority, and a request for a damage report should be made.
GENERAL INSTALLATION AND OPERATION INSTRUCTIONS
1. Place the warmer into mains socket and set energy control to the
high position - setting 6. The elements will burn continuously.
2. After initial warm up, set the energy control to the required heat.
Please note that the element will cycle on and o at heat settings
less than maximum.
3. The warmer is equipped with one pilot light which indicates the
control action of the energy control.
1
10
CLEANING
1. Always ensure that the unit is disconnected from the main
power supply before cleaning.
2. This unit should not be cleaned with a water jet or immersed
in water. Use only a damp cloth or sponge dipped in
soapy water.
3. Wipe o the unit with a dry cloth and wait at least a half
an hour before re-connecting to the main power outlet.
CLEAN THE STAINLESS STEEL PARTS WITH WATER
AND SOAP. AVOID THE USE OF DETERGENTS
CONTAINING ABRASIVE SUBSTANCES. ALWAYS
RINSE WELL AND DRY CAREFULLY AFTER
CLEANING. DO NOT USE PRODUCTS CONTAINING
AGGRESSIVE CHEMICALS, ACIDS OR PRODUCTS
WITH CHLORINE TO CLEAN THE STAINLESS STEEL
EVEN IF DILUTED
WARNING
Burn Hazard.
Do not touch hot food,liquid or heating surfaces
while equipment is heating or operating
Hot surfaces and food can burn skin. Allow the hot surfaces to cool
before handling
2
Part
No.
1 PLASTIC HANDLE
2 NITE-LID
3 DIP-A-LAIT INSERT
4 DIPALAIT ELEMENT
5 BODY ASSEMBLY
6 CONTROL PANEL FACIA
7 PILOT LIGHT
8 BEZEL
9 CONTROL KNOB
10 CONTROL PANEL INSERT
11 ANVIL AXIS LOGO
12 SMALL RUBBER FEET
13 GALVANISED BOTTOM COVER
14 ENERGY REGULATOR
15 CABLE GRIP
16 POWER CORD
17 TERMINAL BLOCK
Description
MODEL:DIP-A-LAIT
MODEL CODE : DLA0002 R01
9
SAFETY
READ ALL INSTRUCTIONS BEFORE USE. FAILURE TO
FOLLOW THESE PRECAUTIONS COULD RESULT IN INJURY TO
YOURSELF AND OTHERS
1. When this appliance is to be positioned in close proximity to a
wall, partitions, kitchen furniture, decorative nishes, etc.it is
recommended that they be made of non-combustible material.
If not, they shall be clad with a suitable non-combustible heat
insulating material, and the closest attention be paid to re
prevention regulations.
2. Use the multifunction warmer on an individual 15A mains outlet
only. DO NOT OVERLOAD THE CIRCUIT.
3. Ensure that the equipment and the power supply cord does not
come into contact with hot surfaces.
4. Supervision is necessary when the appliance is used in close
proximity to children.
5. If the supply cord is damaged, it must be replaced with a new
cord assembly available from the suppliers agent. The cord
shall be an oil resistant sheathed exible cable not lighter
than ordinary polychloroprene or equivalent synthetic
elastomer - sheathed cord (code designation 60245 IEC 57)
6. Use only earthed outlets matching the serial plate voltage.
7. Have equipment installed by a qualied personnel in accordance
with local codes and ordinances.
8. Use equipment in a at level position.
9. Do not operate unattended
10. The equipment may be hot, even though the pilot light is not on.
11. Do not operate if equipment has been damaged or is malfunc-
tioning in any way.
12. These units are designed to run only on alternating current
(A.C.) DO NOT CONNECT TO DIRECT CURRENT (D.C)
WARNING
Electric Shock Hazard.
Keep water and other liquids from entering the inside
of the equipment. Liquid inside the equipment could
cause an electrical shock
Do not spray water or cleaning products. Liquid could contact the
electrical components and cause a short circuit or an electrical shock.
Do not use equipment if power cord is damaged or has been modied
3
EXPLODED DIAGRAM
DIP-A-LAIT
DLA0002 R01
8
POSITIONING DIAGRAM
DIP-A-LAIT
DLA0002 R01
340mm
247mm
307mm
4
LEGEND DESCRIPTION PART NUMBER
ER ENERGY REGULATOR 1-EGO-ER-120V
E1 ELEMENT 125W/230V 5-120V-125W-DIP
H1 CONTROL PILOT LIGHT 1-PL-BMA7102
WIRING DIAGRAM
MODEL CODE: DLA0002-120 R01
MODEL: DIP-A-LAIT
H1
L
120V
N
E
E1
ER
S1
P2
P1
S2
24
7
IT IS ESSENTIAL TO MAKE SURE THAT THE INCOMING
VOLTAGE IS THE SAME AS THE RATED VOLTAGE OF
THE OF THE UNIT AS FOUND ON THE SERIAL PLATE.
THE SERIAL PLATE IS LOCATED AT THE REAR OF THE
UNIT ADJACENT TO THE INCOMING CABLE ENTRY.
ELECTRICAL CONNECTION INFORMATION
MODEL DESCRIPTION VOLTS
(V /Hz)
POWER
(W)
DLA0002 R01 DIP-A-LAIT 230/50 125
DLA0002-120 DIP-A-LAIT 120/60 125
5
LEGEND DESCRIPTION PART NUMBER
ER ENERGY REGULATOR 1-ER-URS0012
E1 ELEMENT 125W/230V 5-125W-DIPALAY
H1 CONTROL PILOT LIGHT 1-PL-BMA0001
WIRING DIAGRAM
MODEL CODE: DLA0002 R01
MODEL: DIP-A-LAIT
H1
L
120V
N
E
E1
ER
S1
P2
P1
S2
24
220V
6
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI