Contec AIO-120802LN-USB Owner's manual

Brand: Contec

Model: AIO-120802LN-USB

Type: Owner's manual

This manual is also suitable for

AIO-121602LN-USB

PC-HELPER

N Series for USB

Multifunction DAQ Unit

(16ch AI, 2ch AO, 16ch DIO)

AIO-121602LN-USB

Multifunction DAQ Unit

(8ch AI, 2ch AO, 16ch DIO)

AIO-120802LN-USB

User’s Guide

CONTEC CO., LTD.

AIO-121602LN-USB, AIO-120802LN-USB

Check Your Package

Thank you for purchasing the CONTEC product.

The product consists of the items listed below.

Check, with the following list, that your package is complete. If you discover damaged or missing items,

contact your retailer.

Product Configuration List

- Unit (One of the following) …1

[AIO-121602LN-USB, AIO-120802LN-USB]

- USB cable (1.8m) …1

- USB cable attachment on the main unit’s side (For Mini B connector side) …1

- First step guide … 1

- I/O connector

AIO-121602LN-USB …6

AIO-120802LN-USB …5

- Rubber feet …4

- Magnet …2

- CD-ROM *1 [API-USBP(WDM)] …1

- Warranty Certificate…1

- Serial number label …1

*1 The CD-ROM contains the driver software and User’s Guide (this guide)

AIO-121602LN-USB, AIO-120802LN-USB

No part of this document may be copied or reproduced in any form by any means without prior written

consent of CONTEC CO., LTD.

CONTEC CO., LTD. makes no commitment to update or keep current the information contained in this

document. The information in this document is subject to change without notice.

All relevant issues have been considered in the preparation of this document. Should you notice an

omission or any questionable item in this document, please feel free to notify CONTEC CO., LTD.

Regardless of the foregoing statement, CONTEC assumes no responsibility for any errors that may

appear in this document or for results obtained by the user as a result of using this product.

Trademarks

MS, Microsoft, Windows and Windows NT are trademarks of Microsoft Corporation. Other brand and

product names are trademarks of their respective holder.

AIO-121602LN-USB, AIO-120802LN-USB

iii

Table of Contents

Check Your Package ............................................................................................................................ i

Copyright ............................................................................................................................................ ii

Trademarks .......................................................................................................................................... ii

Table of Contents ............................................................................................................................... iii

1. BEFORE USING THE PRODUCT 1

About the Unit ..................................................................................................................................... 1

Features ........................................................................................................................................ 1

Support Software .......................................................................................................................... 3

Customer Support................................................................................................................................ 4

Web Site ....................................................................................................................................... 4

Limited One-Year Warranty ............................................................................................................... 4

How to Obtain Service ........................................................................................................................ 4

Liability ............................................................................................................................................... 4

Safety Precautions ............................................................................................................................... 5

Safety Information ....................................................................................................................... 5

Handling Precautions ................................................................................................................... 5

Environment ................................................................................................................................. 8

Inspection ..................................................................................................................................... 8

Storage ......................................................................................................................................... 9

Disposal ........................................................................................................................................ 9

2. SETUP 11

What is Setup?................................................................................................................................... 11

Installing the driver .................................................................................................................... 11

Step 1 Setting the Hardware .............................................................................................................. 12

Name of each parts ..................................................................................................................... 12

Step 2 Initializing the Software ......................................................................................................... 13

Illustration of Menu Screen ........................................................................................................ 13

Installation of API-USBP(WDM) Development Environment .................................................. 14

Installing C-LOGGER ................................................................................................................ 15

Step 3 Installing the Hardware .......................................................................................................... 16

Connecting the Product .............................................................................................................. 16

Setting with the Found New Hardware Wizard ......................................................................... 17

Setting Properties Using Device Manager ................................................................................. 18

Step 4 Checking Operations with the Diagnosis Program ................................................................ 20

What is the Diagnosis Program? ................................................................................................ 20

Check Method ............................................................................................................................ 20

Using the Diagnosis Program ..................................................................................................... 21

AIO-121602LN-USB, AIO-120802LN-USB

Setup Troubleshooting ...................................................................................................................... 24

Symptoms and Actions ............................................................................................................... 24

If your problem cannot be resolved ............................................................................................ 24

3. CONNECTION AND INSTALLATION 25

Installation Method ........................................................................................................................... 25

Mounting on a DIN Rail ............................................................................................................. 25

Desktop Installation .................................................................................................................... 27

Wall Installation ......................................................................................................................... 27

Installation Using the Magnet .................................................................................................... 28

Installation Conditions ...................................................................................................................... 30

Connection Method ........................................................................................................................... 32

Connecting an Interface Connector ............................................................................................ 32

Signal Layout on the Interface Connector .................................................................................. 33

Analog Input Signal Connection ....................................................................................................... 41

Single-ended Input ..................................................................................................................... 41

Differential Input ........................................................................................................................ 42

Analog Output Signal Connection .................................................................................................... 43

Connecting I/O Signals ..................................................................................................................... 44

I/O Circuit .................................................................................................................................. 44

Example of Connection .............................................................................................................. 44

Counter signals and Control signals Connection ............................................................................... 45

4. APPLICATION DEVELOPMENT 47

Reference to Online Help .................................................................................................................. 47

Printing Function Reference .............................................................................................................. 47

Sample Program ................................................................................................................................ 48

Distributing Developed Application ................................................................................................. 48

Use of utility program ....................................................................................................................... 49

Returning to Initial State ................................................................................................................... 54

5. ABOUT C-LOGGER 55

Outline of C-LOGGER ..................................................................................................................... 55

6. FUNCTION 57

Analog Input Function ...................................................................................................................... 57

1. Setting the Conversion Conditions ......................................................................................... 58

2. Starting/Stopping Operation ................................................................................................... 64

3. Monitoring the Status and Acquiring Data ............................................................................. 64

4. Reset ....................................................................................................................................... 69

Analog Output Function .................................................................................................................... 70

AIO-121602LN-USB, AIO-120802LN-USB

1. Setting the Conversion Conditions ......................................................................................... 71

2. Starting/Stopping Operation ................................................................................................... 78

3. Monitoring the Status and Acquiring Data ............................................................................. 78

4. Reset ....................................................................................................................................... 79

Counter Function ............................................................................................................................... 80

1. Setting the Operating Conditions ........................................................................................... 80

2. Starting/Stopping Operation ................................................................................................... 81

3. Monitoring the Status and Acquiring Data ............................................................................. 81

4. Reset ....................................................................................................................................... 82

Digital Input Function ....................................................................................................................... 83

Digital Output Function .................................................................................................................... 84

7. ABOUT HARDWARE 85

Hardware specification ...................................................................................................................... 85

Physical dimensions .......................................................................................................................... 89

Block Diagram .................................................................................................................................. 90

Control Signal Timings ..................................................................................................................... 91

Control Signal Timings for Analog Input .................................................................................. 91

Control Signal Timings for Analog Output ................................................................................ 92

Control Signal Timings for Counter ........................................................................................... 93

About Calibration .............................................................................................................................. 94

AIO-121602LN-USB, AIO-120802LN-USB

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

Before Using the Product

This chapter provides information you should know before using the product.

About the Unit

This product is a USB2.0-compliant analog I/O unit that extends the analog I/O function of USB port of

PCs.

Compact design not restricting installation location (188.0(W) x 78.0(D) × 30.5(H)) makes it easy to

install the product within the panel or device using DIN rail mounting jigs, or on the floor or wall.

Windows driver library is supplied. Possible to be used as a data recording device for LabVIEW, with

dedicated libraries.

Features

Multi-function

Analog I/O can be implemented in a compact system. The series consists of two different models from

which you can select the best model to suit your application.

The < AIO-121602LN-USB > contains the analog input (12bit, 16ch), analog output (12bit, 2ch).

The < AIO-120802LN-USB > contains the analog input (12bit, 8ch), analog output (12bit, 2ch).

All two models include bi-directional digital inputs / outputs (16points, TTL level) and a counter (32bit

1ch, TTL level). You can select the input/output by the application software in eight signals units.

Analog I/O can be synchronized with an internal timer or external clock.

Analog I/O can both be performed at fixed time intervals and synchronized with an external signal.

- Digital filter function to prevent wrong recognition of external signal chattering is provided.

This product has analog input / output control signal, digital input signal and digital filter function to

prevent it from chattering in counter input signal. (Excluding external clock input signal, counter gate

signal)

Buffer memory available for background processing independent of software

The boards include buffer memory (1K Word each for analog input and output) which can be used in

either FIFO or ring format. This allows analog I/O to be performed independently of the operating state

of the PC or software.

Software-based calibration function

Calibration of analog input/output can be all performed by software. Apart from the adjustment

information prepared before shipment, additional adjustment information can be stored according to the

use environment.

- Compact design not restricting installation location (188.0(W) x 78.0(D) x 30.5(H))

Compact design of 188.0(W) × 78.0(D) × 30.5(H) does not require special installation location.

- Compatible to USB1.1/USB2.0

Compatible to USB1.1/USB2.0 and capable to achieve high speed transfer at HighSpeed (480 Mbps).

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

- Diverse installations such as screw fastening, magnet, DIN rail are possible

Installation on the floor / wall /ceiling is possible by screw fastening, magnet, rubber feet, etc.

In addition, DIN rail mounting mechanism is equipped as standard with the product, making it easy to

install the product within the panel or the device.

- Easy-to-wire terminal connector adopted

Adoption of terminal connector (with screws) enables to achieve easy wiring.

- Windows compatible driver libraries are attached.

Using the attached analog I/O driver API-USBP(WDM) makes it possible to create applications of

Windows. In addition, a diagnostic program by which the operations of hardware can be checked is

provided.

Supported to the data logger software [C-LOGGER] (Analog input only)

Supporting the data logger software [C-LOGGER] that enables the graph display of recorded signal

data, file saving, and dynamic transfer to the spreadsheet software program “Excel”.

Plug-ins for the dedicated libraries, the board also supports MATLAB and LabVIEW.

We offer a dedicated library [ML-DAQ], which allows you to use this product on MATLAB by The

MathWorks as well as another dedicated library [VI-DAQ], which allows you to use the product on

LabVIEW.

These dedicated libraries are available, free of charge (downloadable), on our web site.

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

Support Software

You should use CONTEC support software according to your purpose and development environment.

Windows version of analog I/O driver

API-AIO(WDM)

[Stored on the bundled CD-ROM driver library API-USBP(WDM)]

The API-AIO(WDM) is the Windows version driver library software that provides products in the form of Win32 API

functions (DLL). Various sample programs such as Visual Basic and Visual C++, etc and diagnostic program

*1useful for checking operation is provided.

For more details on the supported OS, applicable language and new information, please visit the CONTEC’s Web site.

Data Logger Software C-LOGGER

[Stored on the bundled CD-ROM driver library API-USBP(WDM)]

C-LOGGER is a data logger software program compatible with our analog I/O products. This program enables the

graph display of recorded signal data, zoom observation, file saving, and dynamic transfer to the spreadsheet software

“Excel”. No troublesome programming is required.

For more details on the supported OS, applicable language and new information, please visit the CONTEC’s Web site.

Data acquisition VI library for LabVIEW VI-DAQ (Available for downloading (free of charge) from

the CONTEC web site.)

This is a VI library to use in National Instruments LabVIEW.

VI-DAQ is created with a function form similar to that of LabVIEW's Data Acquisition VI, allowing you to use

various devices without complicated settings.

For more details on the library and download of VI-DAQ, please visit the CONTEC’s Web site.

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

Customer Support

CONTEC provides the following support services for you to use CONTEC products more efficiently

and comfortably.

Web Site

https://www.contec.com/

Latest product information

CONTEC provides up-to-date information on products.

CONTEC also provides product manuals and various technical documents in the PDF.

Free download

You can download updated driver software and differential files as well as sample programs available in

several languages.

Note! For product information

Contact your retailer if you have any technical question about a CONTEC product or need its price,

delivery time, or estimate information.

Limited One-Year Warranty

CONTEC products are warranted by CONTEC CO., LTD. to be free from defects in material and

workmanship for up to one year from the date of purchase by the original purchaser.

Repair will be free of charge only when this device is returned freight prepaid with a copy of the

original invoice and a Return Merchandise Authorization to the distributor or the CONTEC group

office, from which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the electronic circuitry and

original products. The warranty is not applicable if the device has been tampered with or damaged

through abuse, mistreatment, neglect, or unreasonable use, or if the original invoice is not included, in

which case repairs will be considered beyond the warranty policy.

How to Obtain Service

For replacement or repair, return the device freight prepaid, with a copy of the original invoice. Please

obtain a Return Merchandise Authorization number (RMA) from the CONTEC group office where you

purchased before returning any product.

* No product will be accepted by CONTEC group without the RMA number.

Liability

The obligation of the warrantor is solely to repair or replace the product. In no event will the warrantor

be liable for any incidental or consequential damages due to such defect or consequences that arise from

inexperienced usage, misuse, or malfunction of this device.

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

Safety Precautions

Understand the following definitions and precautions to use the product safely.

Safety Information

This document provides safety information using the following symbols to prevent accidents resulting

in injury or death and the destruction of equipment and resources. Understand the meanings of these

labels to operate the equipment safely.

DANGER indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION indicates a potentially hazardous situation which, if not avoided, may

result in minor or moderate injury or in property damage.

Handling Precautions

Do not use the product where it is exposed to flammable or corrosive gas. Doing so may result in an

explosion, fire, electric shock, or failure.

- Do not strike or bend this product.

Otherwise, this may malfunction, overheat, cause a failure or breakage.

- Do not touch this product's terminals (edge connector) with your hands.

Otherwise, this may malfunction, overheat, or cause a failure.

If the terminals are touched by someone's hands, clean the terminals with industrial alcohol.

- Do not close the ventilation hole(s) of this product by, for example, placing an object. This may

cause overheating, malfunction, and/or failure of the product.

- Do not touch the external connector when the power is on.

Otherwise this may malfunction, overheat, cause a failure due to static electricity.

- Make sure that your PC can supply ample power to all this product installed.

Insufficiently energized products could malfunction, overheat, or cause a failure.

- When connecting multiple units, do one at a time and complete setup for the previous unit before

starting to do the next unit.

- The specifications of this product are subject to change without notice for enhancement and quality

improvement.

Even when using this product continuously, be sure to read the manual and understand the contents.

- Do not modify this product. CONTEC will bear no responsibility for any problems, etc., resulting

from modifying this product.

- Regardless of the foregoing statements, CONTEC is not liable for any damages whatsoever

(including damages for loss of business profits) arising out of the use or inability to use this

CONTEC product or the information contained herein.

WARNING

UTION

ANGER

CAUTION

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

- If you use this product in a noisy environment, attach a ferrite core to USB cable to stabilize the

operation. When attaching a ferrite core, coil it around once or more near the connector while

leaving it open, and then close it.

- Regarding “FCC PART 15 Class A Notice”

This product has acquired the above-mentioned standard.

However, a sufficient margin may not be secured for the standard. In this case, use a ferrite core

(TDK: ZCAT 3035-1330 or a compatible product) for the USB cable.

When attaching the ferrite core, coil it around twice near the connector (1cm from the product)

while leaving it open, and then close it.

- Regarding “VCCI Class A Notice”

This product has acquired the above-mentioned standard.

However, a sufficient margin may not be secured for the standard. In this case, use a ferrite core

(TDK: ZCAT 3035-1330) for the USB cable.

When attaching the ferrite core, coil it around twice near the connector (1cm from the product)

while leaving it open, and then close it.

- Regarding “CE EMC Directive Class A Notice”

The ferrite core must be installed in interface connecting cable so that this product may suit the

above-mentioned standard.

Name

Maker

Turn

Quantity

Installation Site

E04SR301334

SEIWA

on USB cable at product side

E04SR301334

SEIWA

on signal cable at product side(CN2, CN3)

* Equivalent product can also be used.

Image diagram

Ferrite core

Cable

TURN : 1

TURN : 2

TURN : 3

TURN : 4

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

FCC PART 15 Class A Notice

NOTE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in

a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

WARNING TO USER

Change or modifications not expressly approved the manufacturer can void the user's authority to operate this

equipment.

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

Environment

Use this product in the following environment. If used in an unauthorized environment, this product

may overheat, malfunction, or cause a failure.

Operating temperature

0 - 50°C

Humidity

10 - 90%RH (No condensation)

Corrosive gases

None

Floating dust particles

Not to be excessive

Inspection

Inspect the product periodically as follows to use it safely.

Check that the ventilation slit has no obstruction and has no dust or foreign matter adhering.

Moreover, if there is the slit on the case side, please confirm it to the slit similarly.

CAUTION

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

Storage

When storing this product, keep it in its original packing form.

(1) Put this product in the storage bag.

(2) Wrap it in the packing material, and then put it in the box.

(3) Store the package at room temperature at a place free from direct sunlight, moisture, shock,

vibration, magnetism, and static electricity.

Disposal

When disposing of the product, follow the disposal procedures stipulated under the relevant laws and

municipal ordinances.

1. Before Using the Product

AIO-121602LN-USB, AIO-120802LN-USB

2. Setup

AIO-121602LN-USB, AIO-120802LN-USB

Setup

This chapter explains how to set up this product.

What is Setup?

Setup means a series of steps to take before the product can be used.

Different steps are required for software and hardware.

Installing the driver

This section enables you to prepare the software and hardware by operating in accordance with each

step in this chapter using the bundled CD-ROM. Taking the following steps sets up the software and

hardware. You can use the diagnosis program later to check whether the software and hardware function

normally.

Step 1 Setting the Hardware

Step 2 Installing the Software

Step 3 Installing the Hardware

Step 4 Checking Operations with the Diagnosis Program

Uninstall the driver and then set it up again if it cannot be set up properly.

The following shows the basic flow for installing product.

Setting Properties Using

Device Manager

- Setting the Device

Name.

Page 13

Connecting the Product

- Connecting the PC

Installing the Software

- API-USBP(WDM)

Development Environment

- C-LOGGER

age 16

age 19

2. Setup

AIO-121602LN-USB, AIO-120802LN-USB

Step 1 Setting the Hardware

This section describes how to set up the product and how to connect it to a PC.

Name of each parts

LED indicator

The above figure has installed the USB cable attachment.

Figure 2.1. Name of each parts (Front side)

2. Setup

AIO-121602LN-USB, AIO-120802LN-USB

Step 2 Initializing the Software

Install software.

The following description assumes the operating system as Windows XP. Although some user interfaces

are different depending on the OS used, the basic procedure is the same.

Points

- If you are using Windows XP, please log on as Administrator (authorized account) before

proceeding to the following steps.

Illustration of Menu Screen

Points

- Please set up the supplied CD-ROM if it has not been set up. The menu starts automatically.

- If the menu do not start, launch X:AUTORUN.EXE (X:CD-ROM drive) from [Run…] in Start

menu.

- The screen design may be different.

Install C-LOGGER.

Refer to the content of CD

-ROM.

Install Development Environment such as sample

programs and online help

Refer to the user

’s guide.

Install utility.

Page is loading ...

Contec AIO-120802LN-USB Owner's manual

Brand: Contec

Model: AIO-120802LN-USB

Type: Owner's manual

This manual is also suitable for

AIO-121602LN-USB

Download PDF

report

Contec AIO-120802LN-USB Owner's manual

This manual is also suitable for

Contec AIO-120802LN-USB Owner's manual

Related papers

Other documents