Nobacco APYRON User manual

Brand: Nobacco

Model: APYRON

Type: User manual

Nobacco APYRON is an advanced vaping device that offers a range of features and capabilities to enhance your vaping experience. With its 75 watts of power and Bypass Mode, the Nobacco APYRON can handle even the most demanding atomizers. The Temperature Control Technology allows you to precisely control the temperature of your coil, resulting in a more consistent and flavorful vape. Additionally, the Nobacco APYRON features a 2000mAh built-in battery, ensuring long-lasting vaping sessions.

Οδηγός χρήσης

Product manual

Manual de utilizare

Ръководство за употреба

Thank you for selecng NOBACCO ΑΡΥΡΌΝ. Please

read the manual supplied and make sure that you

have fully understood it before using the prod-

uct. If you require any addional informaon about the

product or its use, please consult your local reseller or

visit the NOBACCO’s ocial website at www.nobacco.gr.

NOBACCO DESIGN CENTER, using one of the most ad-

vanced PCB boards created NOBACCO APYRON device.

This sophiscated device uses a high capacity built in

baery and an exquisite Oled screen with plethora of

informaon, augmented contrast and improved visibil-

ity under all lighng condions. Constructed by robust

metal materials, it incorporates a solid steel 510 self ad-

jusng connector that guaranes seamless connecvity

with any atomizer.

With Temperature Control Technology, the most ad-

vanced safety features, 75 was or power and numer-

ous funcons, NOBACCO APYRON will oer you an un-

parallel vaping experience.

PACKAGE CONTENTS*:

1 x NOBACCO APYRON

1 x USB cable

1 x User manual

1 x Authencity card with Scratch&Check security code

Product manual

*The company reserves the right to change the contents and

characteriscs of the package or/and the product without any

prior noce.

ΕΝ

Dimensions: 82x42x22 mm

DEVICE CHARACTERISTICS:

• Metal Body

• Solid Steel buons

• 510 solid steel connector with spring loaded pin

• Micro USB pass-through charging port

• 2000mAh built in baery

• 0.96’’ OLED screen

• Main Funcon (Fire) Buon

• Up Regulatory buon (+)

• Down Regulatory buon (-)

• Colors: Silver, Black, White

Product manual

Main function

button

OLED screen

510 connector

Down regulatory

button (-)

Up regulatory button (+)

reset

Micro USB port

NOBACCO APYRON FUNCTIONS:

Α) Power Mode: The device can adjust the power out-

put from 1-75 was

B) Bypass Mode: Bypass Mode : In this mode the de-

vice’s electronic board is bypassed and all the available

baery’s voltage and current is provided to the atomizer.

It is recommended that the parcular funcon is only

used by experienced users who are already accustomed

with the use of Mechanical MODS. Addionally, the at-

omizers must be checked and ascertained that they are

not short circuited and are in the range of the recom-

mended resistance values.

Misuse may damage the device and the atomizer. Inap-

propriate use will void the warranty.

C) Clock Mode: The screen shows the selected me and

the power

D) Temp Mode (Ni, Ti, SS316): Temperature Control

Mode

E) TCR Mode (M1, M2, M3): Temperature Control

Mode with T.C.R. (Temperature Coecient of Resis-

tance) adjustment

POWER, TEMPERATURE

AND RESISTANCE RANGE:

Power range:

Power Mode/ Clock Mode/Temp mode/TCR mode

1-75 with 0.1 wa increment.

ΕΝ

Temperature Control range:

Temp mode/TCR mode

100°C-315°C with 5°C increment

200°F-600°F with 10°F increment

Resistance Range:

Power Mode/ Clock Mode/ Bypass Mode

0.1-3.5ohm

Temp mode/TCR mode

0.05-1.5ohm

Bypass Mode:

Maximum output voltage is 4.2Volts with a freshly

charged baery. Power (wa) indicaon is relevant to

the atomizer resistance.

Note: 4.2Volts is the theorecal upper limit of the built

in baery. Actual upper limit may be dierent due to

power loss of PCB and wiring

DEVICE USE AND PREPARATION:

In order to acvate the device, press ve (5) consecuve

mes the re buon. The Screen will illuminate and the

NOBACCO APYRON logo will appear. Your device is now

turned on.

Product manual

CAUTION:

During the inial acvaon, the device is by default set

to Clock Mode. Please choose the appropriate opera-

on mode according to your atomizer before using the

device.

To deacvate the device press ve (5) consecuve mes

the re buon. On the Screen the message “NOBACCO

APYRON” will appear and the device will turn o.

DEPENDING ON THE TYPE OF THE ATOMIZER’S COIL

HEAD CHOOSE ONE OF THE FOLLOWING MODES (A/B/

C/D/E)

Press the re buon three (3) consecuve mes in or-

der to cycle through the modes. The top indicator of the

screen will blink, indicang you have entered the sys-

tem’s menu. By pressing the (+) buon, you can cycle

through the modes.

Α) Power Mode

This mode allows you to adjust the device’s power out-

put from 1-75 was

Use only atomizers with coil heads that are not compat-

ible with Temp Modes (read the atomizer’s user manual

for more informaon on the type of coil head).

You can adjust the power output by using the +,- buons.

Always start from the lowest power seng, according to

your atomizer specicaons, gradually increasing unl

you nd your preferred seng.

ΕΝ

Β) Bypass mode

In this mode the device’s electronic board is bypassed

and all the available baery’s voltage and current is pro-

vided to the atomizer.

It is recommended that the parcular funcon is only

used by experienced users who are already accustomed

with the use of Mechanical MODS. Addionally, the at-

omizers must be checked and ascertained that they are

not short circuited and are in the range of the recom-

mended resistance values.

Use only atomizers with coil heads that are not compat-

ible with Temp Modes (read the atomizer’s user manual

for more informaon on the type of coil head).

CAUTION:

Misuse may damage the device and the atomizer. Inap-

propriate use will void the warranty.

C) Clock Mode:

In This mode, the me and the remaining power of the

device are displayed.

Use only atomizers that the coil heads are not compa-

ble with Temp Modes (Read the atomizer’s user manual

for more informaon on the type of coil head).

You can adjust the power output by using the +,- buons.

Always start from the lowest power seng, according to

your atomizer specicaons, gradually increasing unl

Product manual

you nd your preferred seng.

Changing between dial and numerical display:

While in Clock Mode, press the re buon three (3)

consecuve mes. The word “Time” will start blinking.

Press the (-) buon and the date (numerical display) or

the hand set (dial display) will blink. Next press (+) but-

ton to switch between dial/numerical display.

D) Temp mode(Ni, Ti, SS316):

In this mode, you are allowed to adjust the limit of the

coil head temperature in conjuncon with the power

seng of the device.

Three (3) dierent coil head wire types are supported,

each with its own preset mode.

Ni: Coil heads with Νi200 wire

Ti: Coil heads with tanium wire

SS316: Coil heads with solid steel type SS316 wire

ΕΝ

If you are unfamiliar with the type of the coil head you

intend to use, please read the manual of the atomizer.

CAUTION:

Using dierent type of coil head from the one supported

on each Temp mode (Ni, Ti, SS316) may cause damage to

the device and atomizer. Warranty is void due to misuse.

The temperature ranges from 100°C-315°C in 5°C incre-

ments or 200°F-600°F in 10°F increments, with scales

changing cyclic.

Temperature value adjustment is made via the +, - buons.

Seng the power while in TEMP modes:

Press the re buon three (3) consequve mes and

the upper indicator will start blinking. Press the (-) but-

ton unl the PWR indicaon blinks. Press the (+) buon

once to enter into the adjustment and then set the de-

sired power by pressing the +, - buons.

Product manual

Ε) TCR mode (M1, M2, M3)

This mode allows you to manually change the Tempera-

ture Coecient of Resistance (=T.C.R.) of the coil head

of your atomizer, depending on the type of wire it uses.

If you are not aware of the T.C.R. of the wire you intend

to use, please nd out more informaon about the T.C.R

rst and then proceed to any further acon.

Three (3) dierent memories (M1, M2, M3) are support-

ed, each working independently for T.C.R. adjustment.

To adjust the T.C.R.:

While the device is powered o, press together the re

and (+) buons for about ve (5) seconds.

The device enters the menu showing the following print

screen:

ΕΝ

By pressing the +,- buons you cycle through M1, M2,

M3 memories and by pressing the re buon you can

enter the value of each memory.

Input the correct T.C.R. value using the +,- buons.

The range in each memory is 1-1000.

CAUTION:

Using dierent T.C.R. value than the one of the wire may

result in malfuncon of the device and the atomizer.

Warranty is void due to misuse.

Note: If the device detects atomizer with a resistance

bigger than 1.5 ohms, it automacally turns to POWER

mode for safety reasons.

Atomizer Lock:

While the device is powered on, aach the atomizer. Press

the re buon (3) consecuve mes and then the (-) but-

ton unl the resistance indicaon starts to blink. Press the

(+) buon one me to lock/unlock the resistance value.

Atomizer lock is advised for the correct funcon of the de-

vice in Temp Modes (TEMP Ni-Ti-SS316/TCR Mode).Each

me you use a new atomizer or a new coil head atomizer

lock procedure should be followed for top performance.

Note: Device and atomizer must be in room tempera-

ture in order for the atomizer lock procedure to be done

correctly. In any other case indicaons of temperature

and resistance may dier from the actual resulng in

poor performance.

Product manual

Your device can auto detect the value of the atomizer’s re-

sistance. If it detects a dierence greater than 0.05 ohms,

while in Temp Modes, the device prompts you to choose if

there is a new coil aached with following message:

Choose new coil by pressing the (+) buon, if you are

using a dierent coil/atomizer than the one before the

message appeared or same coil by pressing (-) if it is the

same coil/atomizer.

AMP/PUFF/TIME

Your device allows you to have three (3) dierent indica-

ons at the boom line of the screen.

ΑMP: Amperes used while vaping

PUFF*: Pu counter

ΤΙΜΕ*: Device usage in seconds

To choose your preferred reading: Press three (3) con-

secuve mes the re buon and then the (-) buon

ΕΝ

unl the last indicator starts to ash. By pressing the (+)

buon you change through the indicaons.

*Note: The manufacturer makes extra quality control tesng

on the device before packing. Potenally other indicaons

than zero, in PUFF/TIME counters, while the inial acvaon

of the device, are a result of the quality control tesng.

USE

Screw the atomizer on the device without using exceed-

ing force and then inhale gently by pressing the re but-

ton of the device.

For peak performance you are advised to start your

draw one (1) second aer you press the re buon and

leave it one (1) second prior to the end of your inhale.

SUPPLEMENTARY FUNCTIONS

Game mode:

With the device powered on simulta-

neously press the re and (+) buon to

enter SCREEN mode. Press the (+) buon

unl you enter GAME mode. Three (3)

Product manual

levels of diculty are available (EASY-NORMAL-HARD) or

you can exit by pressing the EXIT sign.

Note: You cannot vape while in Game Mode.

Logo:

With the device powered on simulta-

neously press the re and (+) buon

to enter SCREEN mode. Press the (+)

buon unl you enter LOGO mode.

Key Lock/Unlock:

With the device powered on press simultaneously the

+,- buons to lock/unlock the adjustmens of power/

temperature.

ΕΝ

Note: If you wish to carry the device in a bag/suitcase,

please turn it o for safety reasons. Your device has a

ten (10) seconds cut o system for protecon of the at-

omizer and the baery from prolonged use.

Screen Protecon

With the device powered on, simultaneously press the

re and (+) buon to enter SCREEN mode. With +,- but-

tons you can choose the me of the screen protecon.

Screen orientaon:

With the device powered o, simultaneously press the

+,- buons to change the screen orientaon by 180°.

MALFUNCTION AND PROTECTION

INDICATIONS

Over 10s protecon: Fire buon is pressed over ten

(10) seconds. Device cuts power automacally.

Atomizer Short-circuit Protecon: Atomizer coil head

is short circuited. Replace with a new one or check the

atomizer.

Low power Alert: Baery volts are below 3.3V. Please

charge the device.

Product manual

Weak Baery Alert: Baery volts during usage drop

below 2.9V. The device regulates the waage to protect

the baery.

Αtomizer Low Alert: The atomizer has a resistance that is

below the minimum specicaons of the device. Please,

replace with one that is within the specicaon range.

ΕΝ

Temperature Protecon: Temp Protecon System is ac-

vated according to your sengs.

Temperature Alert: The internal device temperature is

over 70°C and shuts down for safety reasons. “DEVICE

TOO ΗOT” displayed. Wait for the device to cool down

to room temperature before using again.

Stop using the device if the automac shut down sys-

tem fails.

CHARGING YOUR DEVICE

Connect NOBACCO APYRON with the supplied USB cable

to a USB input or a wall adapter with USB output. Once

your device is charged, the charging indicator ( ) will dis-

appear.

CAUTION:

Do not charge the device unaended.

The wall adaptor must not exceed at its output 1.2A/5V

specicaons. Otherwise there is a possibility to dam-

age the device and void the warranty due to inappro-

priate charging.

MAINTENANCE:

Periodically, use a ssue paper or a cloth to clean the at-

omizer and the device threads to remove any dirt and/

or moisture.

Product manual

PRECAUTIONS

• This device is not intended for use by underage per-

sons, non nonsmokers, children, pregnant or breast-

feeding women, persons with or at risk of heart dis-

ease and/or under medicaon for depression.

• This device is not sold or marketed as a smoking ces-

saon device.

• This device may include small parts, so please keep it

away from children and/or pets.

• Please obey the local laws and/or regulaons pertain-

ing to the use of vaping devices.

• Keep the device away from very high or very low tem-

peratures and/or humid environments.

• Do not pierce or in any way damage the device hous-

ing. If the device housing is damaged in any way, di-

rectly contact NOBACCO company.

• If you are not planning to use the device for a long

period of me, fully charge the baery and discon-

nect the atomizer. Repeat charging once every month.

• Keep the device away from children and minors.

ΕΝ

WARRANTY

This equipment has been tested and found to be free of

defects in materials and workmanship that result in fail-

ure during normal usage. This warranty is extended to

the original end-user purchaser, beginning at the me

of retail purchase. Under this warranty, we will replace

or repair, free of charge, any defecve materials. This

warranty does not cover misuse, unauthorized modi-

caons and external uses such as acts of nature. This

warranty does not cover normal wear and tear. In such

a case, the service department will inform you of the ex-

act cost pertaining to the repair of your device and will

request your approval before proceeding to any further

acon. For more informaon about the warranty peri-

od, please visit the product’s ocial webpage at www.

nobacco.gr or ask your local reseller.

NOBACCO COMPANY CANNOT BE HELD RESPONSIBLE FOR

DAMAGES THAT MAY OCCUR DUE TO INAPPROPRIATE USE

OF THE DEVICE OR INCORRECT COMPLIANCE WITH THE

PROCEDURES DESCRIBED IN THE USER MANUAL

No part of this guide may be reproduced, translated or

transmied in any form or by any means without the

prior wrien permission of NOBACCO Company.

Product manual

Page is loading ...

Nobacco APYRON User manual

Brand: Nobacco

Model: APYRON

Type: User manual

Download PDF

report

Nobacco APYRON User manual

Nobacco APYRON User manual

Other documents