ASSEMBLY INSTRUCTIONS 1 of 3
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
4. Strictly no power drill to assemble. Use only the screwdrivers for installation to
protect the wood frame.
NOTE : 1. THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY
Tool needed : Screwdriver & Rubber Mallet (not provider).
STEP 1 STEP 2
HARDWARE LIST
ITEM DESCRIPTION QTY
1 WOOD DOWEL M10 x 30mm 9 PCS
2 WOOD BUTTON DIA 13.5 x 9mm 2 PCS
3 JCBB BOLT M8 x 50mm 9 PCS
4 M8 FLAT WASHER 3 PCS
5 M8 SPRING WASHER 9 PCS
6 WOOD SCREW M4 x 38mm 6 PCS
7 M5 ALLEN KEY (BALL SHAPE) 1 PC
PART LIST
ITEM DESCRIPTION QTY
A ARM (L/R) 2 PCS
B FRONT RAIL 1 PC
C BACK RAIL 1 PC
D BACK SUPPORT RAIL 1 PC
E CUSHION BACK 1 PC
F CUSHION SEAT 1 PC
1
B1
C1
D
BACK
FRONT
FRONT
BACK
SIDE VIEW
INSIDE
OUTSIDE
7
3
5
D
3
7
5
STEP 2.1
STEP 2.2
STEP 2.3
FRONT
BACK
AR
D
BC
INSIDE
ASSEMBLY INSTRUCTIONS 2 of 3
STEP 3 STEP 5
STEP 4
STEP 3.1
STEP 3.2
STEP 3.3
7
5
3
7
5
3
D
B
C D
AL
6
L
F
E
9
ASSEMBLY INSTRUCTIONS 3 of 3
STEP 6 STEP 7
6
STEP 8 STEP 9
2
735
4
ASSEMBLY INSTRUCTIONS 1 of 2
Read this instruction carefully. See hardware and furniture part list for guidance.
Be sure all parts are complete, before you assemble. Place all wooden furniture
parts on a clean and flat soft surface to prevent from being scratched.
Follow the figure to start assembling.
CAUTIONS : 1. Do not FULLY - TIGHTEN the nut or nut bolt until all nut or bolt is ready assembed.
2. Do not OVER - TIGHTEN the nut or bolt to avoid causing damages to the thread.
3. Keep all hardware parts out of reach of children.
4. Strictly no power drill to assemble. Use only the screwdrivers for installation to
protect the wood frame.
NOTE : 1. THE LIST AND QUANTITY SHOWN ARE FOR 1 UNIT ASSEMBLY
Tool needed : Screwdriver & Rubber Mallet (not provider).
STEP 1 STEP 2
HARDWARE LIST
ITEM DESCRIPTION QTY
1 JCBB BOLT M8 x 50mm 4 PCS
2 M8 SPRING WASHER 4 PCS
3 WOOD SCREW M4 x 38mm 4 PCS
4 WOOD DOWEL M10 x 30mm 8 PCS
5 M5 ALLEN KEY (BALL SHAPE) 1 PCS
PART LIST
ITEM DESCRIPTION QTY
A ARM (L/R) 2 PCS
B FRONT RAIL 1 PC
C BACK RAIL 1 PC
D CUSHION SEAT 1 PC
B
SIDE VIEW
FRONT
BACK
INSIDE
OUTSIDE
INSIDE
OUTSIDE
SIDE VIEW
FRONT
C
4
4
STEP 2.1
R
STEP 2.2
2
1
5
B
C
FRONT
BACK
AR
ASSEMBLY INSTRUCTIONS 2 of 2
STEP 3 STEP 5
STEP 4
3
FRONT
BACK
D
R
STEP 3.1
STEP 3.2
2
1
5B
C
FRONT
BACK
AL
/
