Posiflex CD-3603R User manual

Brand: Posiflex

Model: CD-3603R

Category: Bar code readers

Type: User manual

This manual is also suitable for

CD-3603U

Package Contents

CD-3603U

 2D image scanner

 USB cable

 Quick setup guide

Parts of the 2D Image Scanner

Default Settings

Scanning the following barcode can restore the engine to the factory defaults.

If your CD-3603U is planned to be installed into our Posiflex kiosk model,

please scan the barcode on the right side.

Trigger Button1

Scan Window

w/ Object Detector

Mounting Screw Hole

Beeper Hole

Interface Cable Connector

CD-3603U

2D Image Scanner

Quick Setup Guide

18091902010 Ver. A0

http://www.posiflex.com

Restore Kiosk Trigger Default

(For Kiosk Model)

Restore All Factory Defaults

Scanner Maintenance

The scanner is designed for long-term trouble-free operation and rarely requires

any maintenance. Only an occasional cleaning of the scanner window is necessary

in order to remove dirt and fingerprints.

Wipe the scan window with a soft lint-free cloth and a non-abrasive cleaner to

avoid the scan window from being scratched and damaged. The scan window can

be cleaned while the scanner is running.

The standard interface cable is attached to the scanner with a 10-pin modular

connector. When the connector is properly seated, it is secured in the scanner by a

flexible retention tab. The cable is designed to be field replaceable. Replacement

cables can be obtained from your authorized distributor. To replace the cable, take

the following steps.

1. Make sure the power of both the host terminal and the scanner is powered off.

2. Disconnect the old scanner cable from the host terminal.

3. Press down the retention tab, and gently pull out the cable.

4. Insert the new interface cable into the bottom of the scanner until it clicks.

Then, plug the new cable into the host.

Troubleshooting

This section contains information about how to solve problems that you may

encounter when operating the scanner. If a trouble occurs, please refer to the

following diagnostic tips as a mean to solve the trouble. However, before referring

to the tips, make sure that the scanner is installed well. If the problem remains,

contact your dealer.

Problem

Diagnostic Tips

The scanner is on but cannot read

any barcode.

The scanner window is dirty. Clean the scanner

window as described in the Scanner

Maintenance section.

The presented barcode type is not enabled. Use

this guide to tell the scanner to accept that type

of barcode.

The host terminal has disabled the scanner.

Check the setup of host terminal.

The barcode type presented is not supported by

the scanner.

The scanner does not accept more

than two or three barcode labels.

Determine whether the required barcode types

are enabled or not.

A stray barcode is sitting somewhere in the

scanner field of view. Remove all barcode labels

from the scanner’s scan volume and try again.

Problem

Diagnostic Tips

The scanner cannot send the data to the POS

system. Make sure that the scanner is installed

well and your host POS system is ready to

receive data.

A barcode is read by the scanner

but not accepted by the POS

system.

The communication settings of the system port

and the scanner do not match. Adjust the settings

to make them match to each other.

The scanner is not installed well. Contact your

dealer for the proper installation. The software

running on the POS system does not support the

data format of the barcode label.

When a barcode stays close to the

scanner, the barcode cannot be read

automatically by the scanner.

Check whether or not you have enabled the

Manual Trigger mode. If you have enabled this

mode accidentally, please disable the Manual

Trigger mode by scanning the “Disable trigger”

barcode in the advanced user manual.

Programming Codes

Below are some suggestion you need to bear in mind while scanning labels:

1. The barcode labels shown in bold and black are default factory settings.

2. Please cover the unwanted codes for scanning the specific barcode required

for the programming to prevent confusion in code scanning.

3. Use the user manual downloaded from our global website for advanced

programming.

4. While scanning the setup barcode labels provided in the quick guide, you need

to pull the trigger to initiate the decoding process.

Report Version

Scan the bar code below to report the version of software currently installed in

the decoder.

Report Software Version

Report Scan Engine Manufacturing Information

Scan the bar code below to report the part number, serial number, and

manufacture date of the scan engine.

Report Scan Engine Manufacturing Information

USB Device Type

Scan one of the following barcodes to select the USB device type.

NOTE: When changing USB Device Types, the engine resets and issues the

standard startup beep sequences.

NOTE: Before selecting USB CDC Host (Virtual COM), install the USB

CDC driver located at Posiflex Global Website.

USB Keyboard HID

USB CDC Host

(Virtual COM)

SSI over USB CDC

Trigger Mode

 Standard (Level): A trigger press activates decode processing. Decode

processing continues until the bar code decodes, or you release the

trigger.

 Presentation (Blink): The engine activates decode processing when it

detects a bar code in its field of view. After a period of non-use, the

LEDs turn off until the engine senses motion.

 Host: A host command issues the decode signal. The decoder interprets

an actual trigger pull as a Level triggering option.

 Auto Aim: The decoder projects the aiming pattern when the decoder

senses motion. A trigger press activates decode processing. After a

period of inactivity the aiming pattern shuts off.

 Auto Aim with Illumination: The decoder projects the aiming pattern

and internal illumination LEDs when the decoder senses motion. A

trigger pull activates decode processing. After 2 seconds of inactivity the

aiming pattern and internal illumination LEDs automatically shut off.

*Standard (Level)

Presentation (Blink)

Host

Auto Aim

Auto Aim with Illumination

Illumination

Selecting Enable Decoding Illumination causes the engine to turn on

illumination every image capture to aid decoding. Select Disable Decoding

Illumination to prevent the engine from using decoding illumination.

Enabling illumination usually results in superior images. The effectiveness of

illumination decreases as the distance to the target increases.

*Enable Decoding Illumination

Disable Decoding Illumination

Aiming

Scan one of the following barcodes to select when to project the aiming pattern

in hand-held mode:

 Enable Decode Aiming Pattern: This projects the aiming pattern during

barcode capture.

 Disable Decode Aiming Pattern: This turns the aiming pattern off.

 Enable Decode Aiming Pattern on PDF: This projects the aiming pattern

when the decoder detects a PDF barcode.

*Enable Decode Aiming Pattern

Disable Decode Aiming Pattern

Enable Decode Aiming Pattern on PDF

Beep After Good Decode

Scan one of the following bar codes to select whether or not the engine beeps

after a good decode. If you select Disable Beep After Good Decode, the

beeper still operates during parameter menu scanning a indicate error

conditions.

*Enable Beep After Good Decode

Disable Beep After Good Decode

Enabling/Disabling of readable codes

Scan the Disable All Code Types bar code to disable all symbologies.

Scan Enable All Code Types to enable all symbologies.

Disable All Code Types

Enable All Code Types

*Enable UPC-A

Disable UPC-A

*Enable UPC-E

Disable UPC-E

Enable UPC-E1

*Disable UPC-E1

*Enable EAN-8/JAN-8

Disable EAN-8/JAN-8

*Enable EAN-13/JAN-13

Disable EAN-13/JAN-13

Enable Bookland EAN

*Disable Bookland EAN

Enable ISSN EAN

*Disable ISSN EAN

*Enable Code 128

Disable Code 128

*Enable GS1-128

Disable GS1-128

*Enable ISBT 128

Disable ISBT 128

*Enable Code 39

Disable Code 39

*Enable Code 93

Disable Code 93

Enable Code 11

*Disable Code 11

Enable Interleaved 2 of 5

*Disable Interleaved 2 of 5

Enable Discrete 2 of 5

*Disable Discrete 2 of 5

*Enable Codabar

Disable Codabar

Enable MSI

*Disable MSI

Enable Chinese 2 of 5

*Disable Chinese 2 of 5

Enable Matrix 2 of 5

*Disable Matrix 2 of 5

Enable Korean 3 of 5

*Disable Korean 3 of 5

*Enable GS1 DataBar Omnidirectional

Disable GS1 DataBar Omnidirectional

Enable CC-C

*Disable CC-C

Enable CC-A/B

*Disable CC-A/B

Enable TLC39

*Disable TLC39

*Enable PDF417

Disable PDF417

Enable MicroPDF417

*Disable MicroPDF417

*Enable Data Matrix

Disable Data Matrix

Enable GS1 Data Matrix

*Disable GS1 Data Matrix

Enable Maxicode

*Disable Maxicode

*Enable QR Code

Disable QR Code

*Enable GS1 QR

Disable GS1 QR

*Enable MicroQR

Disable MicroQR

*Enable Aztec

Disable Aztec

Enable Han Xin

*Disable Han Xin

Enable US Postnet

*Disable US Postnet

Enable US Planet

*Disable US Planet

Enable UK Postal

*Disable UK Postal

Enable Japan Postal

*Disable Japan Postal

Enable Australia Post

*Disable Australia Post

Enable Netherlands KIX Code

*Disable Netherlands KIX Code

Enable USP4 4CB/One

Code/Intelligent Mail

*Disable USPS 4CB/One Code/

Intelligent Mail

Enable UPU FICS Postal

*Disable UPU FICS Postal

*Disable Mailmark

Enable Mailmark

Specifications

Item

Characteristics

Image Resolution

1280 x 960 pixels, rolling shutter

Field of View (FOV)

Horizontal: 44.5˚ , Vertical: 33.5˚

Scan Angle

Roll: 360˚

Pitch: ±60˚ (approx.)

Skew: ±60˚ (approx.)

Light Source

Aiming: Green LED

Illumination: Warm white LED

Operating Voltage

5.0 +/- 0.5V

Physical Characteristics

Colors: Black & Gray

Dimensions: 163 mm (H) x 79 mm (W) x 63 mm (D)

Weight: 191.5g

Typical Depth of Field

5 mil Code 39: 2.4 in./6.1 cm to 9.5 in./24.1 cm

5 mil Code 128: 2.8 in./7.1 cm to 9.0 in./22.9 cm

6.67 mil PDF 417: 2.4 in./6.1 cm to 8.0 in./20.3 cm

10 mil DataMatrix: 2.9 in./7.4 cm to 8.5 in./21.6 cm

100% UPCA: 1.8 in./4.6 cm to 19.5 in./49.5 cm

15 mil QR: 1.2 in./3.0 cm to 11.5 in./29.2 cm

20 mil QR: 1.2 in./3.0 cm to 14.0 in./35.6 cm

Interface

USB

OS Support

Android or Windows

Temperature

Operating: 0℃~ +40℃

Non-operating: -20℃~ +60℃ (storage)

Relative Humidity

Operating: 95% RH, non-condensing at 50° C

Storage: 85% RH, non-condensing at 60° C

Ambient Light

0~107,639 lux (direct sunlight)

Outline Dimension

※

The product information and specifications are subject to change without

prior notice. To get the detailed information of the CD-3603U, please

check this model from Posiflex Global Website.

(http://www.posiflex.com/en-global/Download/download). Or download

the advanced manual for more detailed settings.

Posiflex CD-3603R User manual

Brand: Posiflex

Model: CD-3603R

Category: Bar code readers

Type: User manual

This manual is also suitable for

CD-3603U

Download PDF

report

Posiflex CD-3603R User manual

This manual is also suitable for

Posiflex CD-3603R User manual

Related papers

Other documents