Schneider Electric VW3CANTAP2 Operating instructions

Schneider Electric
Brand
Schneider Electric
Model
VW3CANTAP2
Type
Operating instructions

This manual is also suitable for

BBV5513001
BBV55130-01
03 / 2010
VW3CANTAP2
Electrical equipment should be installed, operated, serviced, and maintained only by qualifed personnel. No responsibility
is assumed by Schneider Electric for any consequences arising out of the use of this product.
© 2010 Schneider Electric. All Rights Reserved.
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Read and understand this manual and the manuals of the drive before installing this option.
• Installation must be performed by qualified personnel
• The user is responsible for compliance with all international and national electrical code requirements with respect
to grounding of all equipment.
• Many parts of this drive, including the printed circuit boards, operate at the line voltage. DO NOT TOUCH. Use only
electrically insulated tools.
• DO NOT touch unshielded components or terminal strip screw connections with voltage present.
• DO NOT short across terminals PA/+ and PC/– or across the DC bus capacitors.
• Before servicing the drive:
- Disconnect all power, including external control power that may be present.
- Place a “DO NOT TURN ON” label on all power disconnects.
- Lock all power disconnects in the open position.
- WAIT 15 MINUTES to allow the DC bus capacitors to discharge.
- Measure the voltage of the DC bus between the PA/+ and PC/– terminals to ensure that the voltage is less than 42 Vdc.
- If the DC bus capacitors do not discharge completely, contact your local Schneider Electric representative. Do not repair
or operate the drive.
• Install and close all covers before applying power or starting and stopping the drive.
Failure to follow these instructions will result in death or serious injury.
DANGER
1/3
S1 S2
S3
ON
S4 S5
OFF
ATV 2
ATV 1
SoMove
PowerSuite
Bornier /
Terminal blocks
Fin de ligne /
End line /
R120
ATV1 ATV2
Power
Suite
ATV 1ATV 2
S1 S2
S3
ON
S4 S5
OFF
Dernier ATV /
Last ATV
SoMove
PowerSuite
Bornier /
Terminal blocks
Fin de ligne /
End line /
R120
ON OFF
R120
ON OFF
R120
2/3
1 2 3 4 5
GND
CAN_L
SHLD
CAN_H
(V+)
2
3
4
5
CAN_L
SHLD
CAN_H
(V+)
Bleu /
Blue
Blindage de câble nu /
Bare cableshield
Blanc /
White
Rouge /
Red
Broche / Pin Signal Couleur de fil / Wire color Description
1GND Noir /
Black
Masse /
Ground
Polarité CAN_L /
CAN_L bus line
Blindage en option /
Optional shield
Polarité CAN_H /
CAN_H bus line
Alimentation optionnelle /
Optional supply
(0.32 in) 8mm
54 mm (2.16 in)
Blindage / Shielding
m (0.32 in)m8
3/3
1 to 1.4 N.m
(8.9 to 12.4 lb.in)
0.22 to 0.25 N.m
(1.95 to 2.21 lb.in)
  • Page 1 1
  • Page 2 2
  • Page 3 3

Schneider Electric VW3CANTAP2 Operating instructions

Schneider Electric
Brand
Schneider Electric
Model
VW3CANTAP2
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents