- 2 -
Thank you for choosing one of our LED TRI ood lights. Prior to use, we
suggest that you carefully read all of the instructions. By following the
suggestions found in this user manual, you can look forward to the reliable
and satisfactory performance of your LED light for years to come. Please
keep the manual for your future reference.
Safety Instructions
You must read and follow these safety instructions
prior to initial use!
• Do not power-up this device while it is still in the
packing. Do not connect it to the mains, before the installation is
nalized. Make sure the power is switched off before installation or
during maintenance.
• Keep children away from the power cord and the device. Children
frequently underestimate the dangers of electrical devices.
• To prevent accidental powering-up, always disconnect the device from
the mains, when it is not going to be used.
• Only connect the device to a properly wired and earthed mains
power socket providing the mains voltage stated in this manual.
• Do not operate the device if the power cord or the mains plug are
damaged.
• Do not place the unit in environments which contain high levels of dust,
heat, or vibration.
• Never submerse the device in water. Wipe it with a slightly moistened
cloth only. Never let any uid get into the housing.
• Make sure that the power cord never becomes wet or moist during use.
• Under no circumstances may you open the device housing. Should you
do so your safety would not be assured and the warranty will become
void. There are no operational components whatsoever inside, only
really high voltage that can give you a deadly shock!
• Notice regarding power disconnection
To completely disconnect the device from the mains power source the
power plug must be removed from the power socket. For this reason
the device must always be placed in a position where a constant
unobstructed access to the power socket is assured, thus in an
emergency situation you are able to immediately pull out the power
plug. To eliminate the risk of re you should completely disconnect the
power plug from the power socket when the device is not going to be
used.
- 3 -
• Always grasp the power cord by the plug. Do not pull on the cord itself
and never touch the power cord with wet hands as this could result in
a short circuit or an electrical shock. Do not place speaker cabinets or
anything else on the power cord and make sure that it does not become
clamped. Place the power cord in a position where it can not be trod on.
A damaged power cord can cause a re or an electrical shock. Check
the power cord from time to time. Should it become damaged contact
our customer service centre to have it replaced.
• Never leave the device unattended during operation.
• Never cover the ventilation slots of the device while it is on. Do not place
this unit in an enclosed environment such as a bookshelf or closet.
Ensure that there is adequate ventilation to cool the unit. Do not place
the device in locations that are subject to direct sunlight of strong articial
light. If you do, it may overheat and become irreparably damaged.
• Before a thunderstorm with a risk of lightning, please disconnect the
device from the electrical power source.
• Do not look at the LED light directly for long time, because that might
permanently damage your eyes.
Product Introduction
The LED TRI ood is a oodlight projector, which is revolutionary in the
history of stage lighting. It takes advantage of latticed LED illumination.
The optical light cup design adds more colors and a soft character to the
light beams. This is quite different from common integrated light beams
utilizing convergent lens. The latest liquid-crystal display makes it easy
and convenient to set light strength and color parameters. Our model
features a 30 degrees color blending lens and a constant ow driving
circuit.
The unit is suitable for use in places with stringent requirements such as
meetings, discos, bars, nightclubs, even gymnasiums and TV stages with
the IP 63 water-proof safety class.
Operation Instruction
After unpacking, please check whether the projector has been damaged
by transport such as screw loosening, broken housing, etc.
Check before electrication. Check whether the projector has been laid
correctly and stably, whether the mains power voltage is adapted to the
requirement, otherwise we’ll not be responsible for any damage to the
device.
- 4 -
This projector is the rst class protected equipment. Notice that while
using, the green and yellow wires have to be connected with the ground
properly by professionals. Please check the voltage before powering it on.
Technical Parameters
Rated voltage: ................. AC100V~240V ±10%
Rated frequency: ............. 50~60Hz
Power consumption: ........ 250W
Quantity of lights: ............. 15pcs 15W lattice high-power light pearls
Control channel: .............. 5
Control signal:.................. DMX-512 international standard signal
Control mode: .................. DMX-512 signal control • automatic • master
......................................... and slave
Operating environment: ... outdoor / IP: 63
As we continuously strive to improve our products, all specications and
appearance are subject to change without prior notice.
Signal Cable
Pin 1 = (! brown !)
Pin 2 = + (blue)
Pin 3 = - (green/yellow)
Function Mode Set
When the unit is switched on, the LCD display will show UNITE STAR,
please press any key to enter the Function Menu.
You can choose function by pressing UP/DOWN, the → arrowhead
symbol shows the current operation position. Press ENTER/EXIT to enter
or return into the current function.
Detailed operating way as below
1. DMX512 Control Mode
Press UP/DOWN to set the address. Press EXIT to return.
2. AUTO Automatic Mode
When showing → Show 00, press UP/DOWN choose effects. Press
EXIT to return.
1) Automatically run all effects -----Show 00
2) Gradually color change effect-----Show 01
3) RGB color change effect-----Show 02
4) Single color ash effect-----Show 03 to Show 09
5) RGB color change ash effect-----Show 10 to Show 20
- 5 -
When showing → Speed80, press UP/DOWN to choose speed. Press
EXIT to return.
3. MUSIC Sound Control Mode
4. MASTER is turned on or not
Press UP/DOWN to choose whether the master has been turned on or
not. Press ENTER to conrm. Press EXIT to return.
5. COLOR SET
Press UP/DOWN to choose the current set color. Press ENTER to
enter the proportion adjustment of the three RGB colors. Press EXIT to
return.
Press UP/DOWN to choose whether to reset the color setting to
factory defaults. Press ENTER to conrm. Press EXIT to return.
6. Back Light is turned on or not
Press UP/DOWN to choose whether the back light has been turned on
or not. Press ENTER to conrm. Press EXIT to return.
7. Master and Slave Combine Mode
Master light has to set Master ON, working in Auto Mode.
Slave light has to set DMX512 to control mode.
DMX-512 channel function
This model adopts international standard DMX-512 signal, with totally 5
channels. Controlling details as below:
Channel DMX-512 value Control Programs
CH1
RGB luminance
adjust 0~136 Adjust total luminance
RGB colour change 137~187 CH5=0, adjust colour change
speed
RGB gradual colour
change 188~239 CH5=0, adjust gradual colour
change speed
Run Inside-set effect 240~255 Automatic-running effect
CH2 Red 0~255 Adjust Red LED luminance
CH3 Green 0~255 Adjust Green LED luminance
CH4 Blue 0~255 Adjust Blue LED luminance
CH5
Flash 0~255 Adjust ash pace
CH1 Set ash
frequency 137~239 Adjust RGB ash colour change
frequency
- 6 -
DMX-512 Signal Connection
This product is assembled with DMX input and output 3 pins XLR socket,
all connect way is to make Pin 1 connected to the ground, Pin 2 connected
to the negative pole signal, Pin 3 connected to the positive pole signal.
NOTICE: No overloading connection, one same connect branch can
connect no more than 32 units.
DMX-512 address code set
This unit is equipped with 5 channels, the address code of the rst light is
1, the second 5+1=6, the third 5+6=11, the fourth 5+11=16,and so on.
Set details as below:
Light number Starting address Binary code dialing (ON)
111
2 6 2, 3
3 11 1, 2, 4
4 16 5
5 21 1, 3, 5
6 26 2, 4, 5
7 31 1, 2, 3, 4, 5
8 36 3, 6
9 41 1, 4, 6
10 46 2, 3, 4, 6
Notice about Master-slave synchronization:
1. When the master machine is running, the light will send DMX-512
signals, but it can’t be connected to the DMX-512 controller, otherwise,
they will interrupt each other, so they can not be synchronized.
2. When many lights are operating in master-slave synchronization mode,
only one of them can be master, the others be slave, or they can’t be
synchronized.
Maintenance
We suggest you clean the light with professional glass cleaning and
downy cloth. Clean the device whenever needed, to get the highest
brightness output.
- 7 -
Disposal
Do not dispose of the device at the end of his operating life
in your normal domestic waste. This device is subject to the
European Guidelines 2002/96/EC.
• Have the product disposed of by a professional disposal company of by
your communal disposal facility.
• Observe the currently applicable regulations. In case of doubt contact
your disposal facility.
• Dispose of packaging materials in an environmentally responsible
manner.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
red lighting QUADRO 24 User manual
-
SHOWTEC eventbar 12/3 User manual
-
Etec E7100305 User manual
-
STUDIO DUE SMART MAX30 RGBWA User manual
-
STUDIO DUE SMART 17 RGBWA User manual
-
-
Microh LED Quadpar TRI MKII User manual
-
-
Cameo Thunder Wash 100RGB User manual
-
