B-K lighting ArtiStar - MR16 Installation guide

Brand
B-K lighting
Model
ArtiStar - MR16
Type
Installation guide
RELEASED
1-25-16
REFERENCE NUMBER
INS-2176-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
NEEDED
FOR
INSTALLATION:
By Others
RING MOUNT SERIES™
Installation Instructions
Waterproof Wire Connectors
Mounting Hardware and Cable
Fully Potted
Mounting
Ring
18 Gauge Wire
TECHNOLOGY
with
TECHNOLOGY
& Low Voltage
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
this product.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturerorinstalledcontrarytoinstructionsmaycausean
unsafecondition.Theuseofdamagedcomponentsmaycause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
asthismaycauseanunsafecondition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
aclean,dry,softclothtohandlethelamp.Oilfromskinmay
damagethelampandcauseittorupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, o-rings and sealing surfaces must be kept clean
duringinstallationandservice;failuretodothismaycausean
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
LightedlampisHOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhenturningon.
Do not touch hot lens, guard, or enclosure
(seediagram/picture).
Keeplampawayfrommaterialsthatmayburn.
Donotouchthelampatanytime.Useasoftcloth.
Oilfromskinmaydamagelamp.
Donotoperatetheluminairefittingwithamissingordamagedshield.
SAVE THESE INSTRUCTIONS
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning Flammable Hot Surface
Suitable for wet locations · Suitable for Indoor/Outdoor use
Low Voltage
Pleaserefertothelowvoltagedesignguideatwww.bklighting.com/lvguidebeforeinstallationforproperwireselection.
This set of instructions works for:
RM-MN - Micro Nite Star™
RM-MM - Mini-Micro™
RM-AR - ArtiStar™
Cable
1. Securely attach mounting hardware and cable
to mounting ring on fixture and suspend to
desired height.
Fixture Installation
RELEASED
1-25-16
REFERENCE NUMBER
INS-2176-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
RING MOUNT SERIES™
Installation Instructions
TECHNOLOGY
with
TECHNOLOGY
& Low Voltage
PROJECT:
TYPE:
2. Make watertight connections from remote
transformer to fixture leads using waterproof
wire connectors (By Others). See wiring
diagram.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
WIRING DIAGRAM
Integral
Transformer
COM
GROUND IN HOUSING
WIRING DIAGRAM
LED - For use with 12VAC
remote transformer or magnetic
transformers only. B-K Lighting cannot
guarantee performance with third party
manufacturers’ transformers.
Low Voltage - For use with 12VAC remote
transformer.
RM-MM - RE-PLACING LED BOARD/DRIVER AND OPTICS
1. Use 5/64” Allen wrench to loosen #8-32 stainless
steelsetscrewandremovecap.
4. Reverse install LED board and driver by carefully
wrapping 18 gauge wires around driver and
insertingintofixturebody.SecureLEDboardin
place with stainless steel set screws.
5. Usesmallflatheadscrewdrivertoremovelens
from optic holder on the LED. Snap new optic
inplace.Replacecaponfixtureandtightenset
screw.
3. Disengage LED board and driver assembly.
Replacewithnewboardanddriverassembly.
2. Use.050”Allenwrenchtoloosentwo(2)#4-40
stainless steel set screws below LED board on
the heat sink. Gently pull up on LED board and
Driverassemblytoexposequickdisconnect.
RELEASED
1-25-16
REFERENCE NUMBER
INS-2176-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
RING MOUNT SERIES™
Installation Instructions
TECHNOLOGY
with
TECHNOLOGY
& Low Voltage
PROJECT:
TYPE:
1. Use 5/64” Allen wrench to loosen #8-32 stainless set
screwandremovecap.
2. Space three fingers evenly around the optic and
gentlyrockoptictoremove.
4. DisengageLEDboardanddriverassembly.Replace
withnewboardanddriverassembly.
5. Reverse install LED board and driver by carefully
wrapping 18 gauge wires around driver and
insertingintofixturebody.SecureLEDboardin
place with stainless steel screws.
6. Snap optics in place. Place cap on fixture and
tighten set screw.
3. Use 5/64” Allen wrench to remove two
(2) #2-56 socket head cap screws on LED
board, grasp LED board and gently pull up to
exposequickdisconnect.
RM-MN - RE-PLACING LED BOARD/DRIVER AND OPTICS
RM-MN - REPLACING LOW VOLTAGE HALOGEN LAMPS
1. Use 5/64” Allen wrench to loosen #8-32 stainless
setscrewandremovecap.
3. Placecaponfixtureandtightensetscrew.Tighten
screw to 1/2 inch pounds. Top of screw should sit
flushwithfixturecap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and will
void warranty.
2. Firmly insert lamp pins into socket to make
connection.Rockingmotionmayberequired.
Do not exceed the maximum wattage listed
onthefixturelabelbeforeinstalling.
RELEASED
1-25-16
REFERENCE NUMBER
INS-2176-00
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
RING MOUNT SERIES™
Installation Instructions
TECHNOLOGY
with
TECHNOLOGY
& Low Voltage
PROJECT:
TYPE:
RM-AR - RE-PLACING LED BOARD/DRIVER AND OPTICS
1. Use 5/64” Allen wrench to loosen #8-32
stainlesssetscrewandremovecap.
2. Space three fingers evenly around the optic
andgentlyrockoptictoremove.
4. Disengage LED board and driver assembly.
Replacewithnewboardanddriverassembly.
5. Reverse install LED board and driver by
carefully  engaging quick disconnects and
inserting into fixture body. Secure LED board
in place with stainless steel screws. Snap optics
in place.
6. With flat head screw driver rotate dial to
desiredlumenoutput.Replacecap.
3. Use 5/64” Allen wrench to remove two (2)
#2-56 socket head cap screws on LED board,
graspLEDboardandgentlypulluptoexpose
quickdisconnect.
RM-AR - REPLACING LOW VOLTAGE HALOGEN LAMPS
1. Use 5/64” Allen wrench to loosen #8-32 stainless
setscrewandremovecap.
3. Placecaponfixtureandtightensetscrew.Tighten
screw to 1/2 inch pounds. Top of screw should sit
flushwithfixturecap.
Warning: Do not over tighten set screw.
Doing so will compromise O Ring seal and will
void warranty.
2. Firmly insert lamp pins into socket to make
connection.Rockingmotionmayberequired.
Do not exceed the maximum wattage listed
onthefixturelabelbeforeinstalling.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

B-K lighting ArtiStar - MR16 Installation guide

Brand
B-K lighting
Model
ArtiStar - MR16
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers