Gigabyte Z370 AORUS GAMING K3 User manual

Brand: Gigabyte

Model: Z370 AORUS GAMING K3

Type: User manual

For more product details, please visit GIGABYTE's website.

To reduce the impacts on global warming, the packaging materials of this product

are recyclable and reusable. GIGABYTE works with you to protect the environment.

Z370 AORUS Gaming K3

User's Manual

Rev. 1001

12ME-Z37AGK3-1001R

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specications and features in this manual may be made by GIGABYTE without prior notice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or

by any means without GIGABYTE's prior written permission.

For quick set-up of the product, read the Quick Installation Guide included with the product.

In order to assist in the use of this product, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means

the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard

BIOS, drivers, or when looking for technical information.

Example:

Motherboard

Z370 AORUS Gaming K3

Sept. 1, 2017

Motherboard

Z370 AORUS Gaming K3

- 3 -

Table of Contents

Z370 AORUS Gaming K3 Motherboard Layout ...............................................................4

Chapter 1 Hardware Installation .....................................................................................5

1-1 Installation Precautions .................................................................................... 5

1-2 ProductSpecications ...................................................................................... 6

1-3 Installing the CPU ............................................................................................ 9

1-4 Installing the Memory ....................................................................................... 9

1-5 Installing an Expansion Card ......................................................................... 10

1-6 Back Panel Connectors .................................................................................. 10

1-7 Internal Connectors ........................................................................................ 12

Chapter 2 BIOS Setup ..................................................................................................21

2-1 Startup Screen ............................................................................................... 21

2-2 M.I.T. .............................................................................................................. 22

2-3 System ........................................................................................................... 28

2-4 BIOS ............................................................................................................... 29

2-5 Peripherals ..................................................................................................... 32

2-6 Chipset ........................................................................................................... 35

2-7 Power ............................................................................................................. 36

2-8 Save & Exit ..................................................................................................... 38

Chapter 3 Appendix ......................................................................................................39

3-1 ConguringaRAIDSet .................................................................................. 39

3-2 Installing an Intel® Optane™ Memory .............................................................. 41

3-3 DriversInstallation .......................................................................................... 43

Regulatory Statements .............................................................................................. 44

Contact Us ................................................................................................................ 48

- 4 -

Z370 AORUS Gaming K3 Motherboard Layout

* The box contents above are for reference only and the actual items shall depend on the product package you obtain.

The box contents are subject to change without notice.

Box Contents

5Z370 AORUS Gaming K3 motherboard 5Four SATA cables

5Motherboard driver disk 5I/O Shield

5User's Manual 5One G Connector

5Quick Installation Guide

KB_MS_USB30 CPU_FAN

ATX_12V_2X4

ATX

F_AUDIO

AUDIO

B_BIOS

PCIEX4

DDR4_2

DDR4_1

DDR4_4

DDR4_3

BAT

F_PANEL

LED_C1

Intel® Z370

CLR_CMOS

M_BIOS

PCIEX1_1

PCIEX16

F_USB1

LGA1151

Z370 AORUS Gaming K3

USB_LAN

F_USB30_2

PCIEX1_2

SYS_FAN2

iTE®

Super I/O

F_USB2

TPM

M2P_32G

SATA3 3 1

2 0

CPU_OPT

TYPEC

R_USB30

DVI

PCIEX1_3

PCIEX1_4

D_LED1

80 60 42

THB_C

SYS_FAN3_PUMP

SPDIF_O

SYS_FAN1

110

USB31

LED_C2

ASMedia®

USB 3.1 Gen 2

Controller

SATA3

5 4

DLED_V_SW1

CODEC

M2Q_32G

80 60 42

D_LED2

DLED_V_SW2

F_USB30_1

HDMI

Intel® GbE

LAN

CPU DRAM

VGA BOOT

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become

damagedasaresultofelectrostaticdischarge(ESD).Priortoinstallation,carefullyreadtheuser's

manual and follow these procedures:

•Prior to installation, make sure the chassis is suitable for the motherboard.

•Priortoinstallation,donotremoveorbreakmotherboardS/N(SerialNumber)stickeror

warranty sticker provided by your dealer. These stickers are required for warranty validation.

•Always remove the AC power by unplugging the power cord from the power outlet before

installing or removing the motherboard or other hardware components.

•Whenconnectinghardwarecomponentstotheinternalconnectorsonthemotherboard,make

sure they are connected tightly and securely.

•Whenhandlingthemotherboard,avoidtouchinganymetalleadsorconnectors.

•It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic

componentssuchasamotherboard,CPUormemory.IfyoudonothaveanESDwriststrap,

keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.

•Prior to installing the motherboard, please have it on top of an antistatic pad or within an

electrostatic shielding container.

•Before connecting or unplugging the power supply cable from the motherboard, make sure

the power supply has been turned off.

•Before turning on the power, make sure the power supply voltage has been set according to

the local voltage standard.

•Before using the product, please verify that all cables and power connectors of your hardware

components are connected.

•To prevent damage to the motherboard, do not allow screws to come in contact with the

motherboard circuit or its components.

•Make sure there are no leftover screws or metal components placed on the motherboard or

within the computer casing.

•Donotplacethecomputersystemonanunevensurface.

•Donotplacethecomputersysteminahigh-temperatureorwetenvironment.

•Turning on the computer power during the installation process can lead to damage to system

components as well as physical harm to the user.

•If you are uncertain about any installation steps or have a problem related to the use of the

product,pleaseconsultacertiedcomputertechnician.

•If you use an adapter, extension power cable, or power strip, ensure to consult with its installation

and/or grounding instructions.

- 5 -

1-2 ProductSpecications

CPU Support for 8th Generation Intel® Core™ i7 processors/Intel® Core™ i5

processors/Intel® Core™ i3 processors in the LGA1151 package

(GotoGIGABYTE'swebsiteforthelatestCPUsupportlist.)

L3 cache varies with CPU

Chipset Intel® Z370 Express Chipset

Memory 4xDDR4DIMMsocketssupportingupto64GBofsystemmemory

Dualchannelmemoryarchitecture

SupportforDDR42666/2400/2133MHzmemorymodules

SupportforECCUn-bufferedDIMM1Rx8/2Rx8memorymodules (operatein

non-ECCmode)

Supportfornon-ECCUn-bufferedDIMM1Rx8/2Rx8/1Rx16memorymodules

SupportforExtremeMemoryProle(XMP)memorymodules

(Go to GIGABYTE's website for the latest supported memory speeds and memory

modules.)

Onboard

Graphics

Integrated Graphics Processor-Intel®HDGraphicssupport:

- 1xDVI-Dport,supportingamaximumresolutionof1920x1200@60Hz

 * TheDVI-DportdoesnotsupportD-Subconnectionbyadapter.

 - 1xHDMIport,supportingamaximumresolutionof4096x2160@30Hz

* SupportforHDMI1.4versionandHDCP2.2.

Maximum shared memory of 1 GB

Audio Realtek® ALC1220 codec

HighDenitionAudio

2/4/5.1/7.1-channel

SupportforS/PDIFOut

LAN Intel®GbELANchip(10/100/1000Mbit)

Expansion Slots 1xPCIExpressx16slot,runningatx16(PCIEX16)

* For optimum performance, if only one PCI Express graphics card is to be installed,

be sure to install it in the PCIEX16 slot.

1xPCIExpressx16slot,runningatx4(PCIEX4)

* The PCIEX4 slot shares bandwidth with the PCIEX1_2, 3, 4 slots. The PCIEX4 slot

operates at up to x1 mode when the PCIEX1_2, 3, or 4 slot is populated.

4 x PCI Express x1 slots

 (AllofthePCIExpressslotsconformtoPCIExpress3.0standard.)

Multi-Graphics

Technology SupportforAMDQuad-GPUCrossFire™and2-WayAMDCrossFire™ technologies

Storage Interface Chipset:

- 1 x M.2 connector (Socket 3, M key, type 2242/2260/2280/22110 SATA and

PCIex4/x2SSDsupport)(M2P_32G)

 - 1xM.2connector(Socket3,Mkey,type2242/2260/2280PCIex4/x2SSD

support)(M2Q_32G)

- 6 x SATA 6Gb/s connectors

 - SupportforRAID0,RAID1,RAID5,andRAID10

* Refer to "1-7 Internal Connectors," for the installation notices for the M.2 and SATA

connectors.

Intel® Optane™ Memory Ready

- 6 -

USB Chipset+ASMedia® USB 3.1 Gen 2 Controller:

- 1 x USB Type-C™ port on the back panel, with USB 3.1 Gen 2 support

 - 1xUSB3.1Gen2Type-Aport(red)onthebackpanel

Chipset:

- 8 x USB 3.1 Gen 1 ports (4 ports on the back panel, 4 ports available through

theinternalUSBheaders)

- 6 x USB 2.0/1.1 ports (2 ports on the back panel, 4 ports available through

theinternalUSBheaders)

Internal

Connectors

1 x 24-pin ATX main power connector

1 x 8-pin ATX 12V power connector

2 x M.2 Socket 3 connectors

6 x SATA 6Gb/s connectors

1 x CPU fan header

1 x water cooling CPU fan header

2 x system fan headers

1 x system fan/water cooling pump header

2xdigitalLEDstripheaders

2xdigitalLEDstrippowerselectjumpers

2xRGB(RGBW)LEDstripheaders

1 x front panel header

1 x front panel audio header

2 x USB 3.1 Gen 1 headers

2 x USB 2.0/1.1 headers

1xS/PDIFOutheader

1xTrustedPlatformModule (TPM)header(2x6 pin,forthe GC-TPM2.0_S

moduleonly)

1 x Thunderbolt™ add-in card connector

1 x Clear CMOS jumper

Back Panel

Connectors

1 x PS/2 keyboard/mouse port

1xDVI-Dport

1xHDMIport

1 x USB Type-C™ port, with USB 3.1 Gen 2 support

1xUSB3.1Gen2Type-Aport(red)

4 x USB 3.1 Gen 1 ports

2 x USB 2.0/1.1 ports

1 x RJ-45 port

 6 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Side Speaker

Out,LineIn,LineOut,MicIn)

I/O Controller iTE® I/O Controller Chip

Hardware

Monitor

Voltage detection

Temperature detection

Fan speed detection

Watercoolingowratedetection

Overheating warning

Fan fail warning

Fan speed control

 * Whetherthefan(pump)speedcontrolfunctionissupportedwilldependonthefan

(pump)youinstall.

- 7 -

BIOS 2x128Mbitash

Use of licensed AMI UEFI BIOS

SupportforDualBIOS™

PnP1.0a,DMI2.7,WfM2.0,SMBIOS2.7,ACPI5.0

Unique Features Support for APP Center

* Available applications in APP Center may vary by motherboard model. Supported

functionsofeachapplicationmayalsovarydependingonmotherboardspecications.

- 3DOSD

- @BIOS

- AutoGreen

- BIOS Setup

- Color Temperature

- Cloud Station

- EasyTune

- EasyRAID

- Fast Boot

- Game Boost

- ON/OFF Charge

- Platform Power Management

- RGB Fusion

- Smart Backup

- Smart Keyboard

- Smart TimeLock

- System Information Viewer

- USB Blocker

- V-Tuner

Support for Q-Flash

Support for Xpress Install

Bundled

Software

Norton®InternetSecurity(OEMversion)

cFosSpeed

Operating

System SupportforWindows1064-bit

Form Factor ATX Form Factor; 30.5cm x 24.4cm

* GIGABYTE reserves theright to make any changes to the productspecications and product-related information

without prior notice.

Please visit GIGABYTE's website

for support lists of CPU, memory

modules,SSDs,andM.2devices.

Please visit the Support\Utility List

page on GIGABYTE's website to

download the latest version of apps.

- 8 -

DualChannelMemoryConguration

ThismotherboardprovidesfourmemorysocketsandsupportsDualChannelTechnology.Afterthememory

isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.EnablingDual

Channel memory mode will double the original memory bandwidth.

Please visit GIGABYTE's website for details on hardware installation.

1-3 Installing the CPU

Read the following guidelines before you begin to install the CPU:

•Make sure that the motherboard supports the CPU.

(GotoGIGABYTE'swebsiteforthelatestCPUsupportlist.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

CPU to prevent hardware damage.

•Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may

locatethenotchesonbothsidesoftheCPUandalignmentkeysontheCPUsocket.)

•Apply an even and thin layer of thermal grease on the surface of the CPU.

•DonotturnonthecomputeriftheCPUcoolerisnotinstalled,otherwiseoverheatinganddamage

of the CPU may occur.

•SettheCPUhostfrequencyinaccordancewiththeCPUspecications.Itisnotrecommended

thatthesystembusfrequencybesetbeyondhardwarespecicationssinceitdoesnotmeetthe

standard requirements for the peripherals. If you wish to set the frequency beyond the standard

specications,pleasedosoaccordingtoyourhardwarespecicationsincludingtheCPU,graphics

card, memory, hard drive, etc.

Installing the CPU

Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

Do not remove the CPU socket cover before inserting the CPU. It may pop off from the load

plate automatically during the process of re-engaging the lever after you insert the CPU.

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•Make sure that the motherboard supports the memory. It is recommended that memory of the same

capacity, brand, speed, and chips be used.

(GotoGIGABYTE'swebsiteforthelatestsupportedmemoryspeedsandmemorymodules.)

•Always turn off the computer and unplug the power cord from the power outlet before installing the

memory to prevent hardware damage.

•Memory modules have a foolproof design. A memory module can be installed in only one direction.

If you are unable to insert the memory, switch the direction.

Triangle Pin One Marking on the CPU

NotchNotch

LGA1151 CPU

Alignment KeyAlignment Key

LGA1151 CPU Socket

Pin One Corner of the CPU Socket

- 9 -

1-6 Back Panel Connectors

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

USB 3.1 Gen 1 Port

TheUSB3.1Gen1portsupportstheUSB3.1Gen1specicationandiscompatibletotheUSB2.0

specication.UsethisportforUSBdevices.

DVI-D Port (Note)

TheDVI-DportconformstotheDVI-Dspecicationandsupportsamaximumresolutionof1920x1200@60Hz

(theactualresolutionssupporteddependonthemonitorbeingused).Connectamonitorthatsupports

DVI-Dconnectiontothisport.

USB 3.1 Gen 2 Type-A Port (Red)

TheUSB3.1Gen2Type-AportsupportstheUSB3.1Gen2specicationandiscompatibletotheUSB

3.1Gen1andUSB2.0specication.UsethisportforUSBdevices.

USB Type-C™ Port

ThereversibleUSBportsupportstheUSB3.1Gen2specicationandiscompatibletotheUSB3.1Gen

1andUSB2.0specication.UsethisportforUSBdevices.

The four memory sockets are divided into two channels and each channel has two memory sockets as following:

ChannelA:DDR4_2,DDR4_4

ChannelB:DDR4_1,DDR4_3

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•Make sure the motherboard supports the expansion card. Carefully read the manual that came

with your expansion card.

•Always turn off the computer and unplug the power cord from the power outlet before installing an

expansion card to prevent hardware damage.

DualChannelMemoryCongurationsTable

DDR4_4 DDR4_2 DDR4_3 DDR4_1

2 Modules - - DS/SS - - DS/SS

DS/SS - - DS/SS - -

4 Modules DS/SS DS/SS DS/SS DS/SS

(SS=Single-Sided,DS=Double-Sided,"--"=NoMemory)

DuetoCPUlimitations,readthefollowingguidelinesbeforeinstallingthememoryinDualChannelmode.

1. DualChannelmodecannotbeenabledifonlyonememorymoduleisinstalled.

2. WhenenablingDualChannelmodewithtwoorfourmemorymodules,itisrecommendedthatmemory

of the same capacity, brand, speed, and chips be used.

(Note) TheDVI-DportdoesnotsupportD-Subconnectionbyadapter.

- 10 -

USB 2.0/1.1 Port

TheUSBportsupportstheUSB2.0/1.1specication.UsethisportforUSBdevices.

Center/Subwoofer Speaker Out (Orange)

Usethisaudiojacktoconnectcenter/subwooferspeakersina5.1/7.1-channelaudioconguration.

Rear Speaker Out (Black)

Thisjackcanbeusedtoconnectrearspeakersina4/5.1/7.1-channelaudioconguration.

Side Speaker Out (Gray)

Usethisaudiojacktoconnectsidespeakersina7.1-channelaudioconguration.

Line In (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.

Line Out (Green)

The line out jack. This jack supports audio amplifying function. For better sound quality, it is recommended

thatyouconnectyourheadphone/speakertothisjack(actualeffectsmayvarybythedevicebeingused).

Use this audio jack for a headphone or 2-channel speaker. This jack can be used to connect front speakers

ina4/5.1/7.1-channelaudioconguration.

Mic In (Pink)

The Mic in jack.

HDMI Port

TheHDMIport supports HDCP2.2 andDolbyTrueHDand DTSHDMaster

Audioformats.It alsosupportsupto192KHz/16bit8-channelLPCMaudio

output.YoucanusethisporttoconnectyourHDMI-supportedmonitor.Themaximumsupported

resolutionis 4096x2160@30Hz,but theactual resolutionssupportedaredependenton themonitor

being used.

•Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour

device and then remove it from the motherboard.

•Whenremovingthecable,pullitstraightoutfromtheconnector.Donotrockitsidetosideto

prevent an electrical short inside the cable connector.

•ToenableorconguretheaudioamplifyingfunctionfortheLineoutjack,pleaseaccesstheHD

Audio Manager application.

•Please visit GIGABYTE's website for more audio software information.

AfterinstallingtheHDMIdevice,makesuretosetthedefaultsoundplaybackdevicetoHDMI.(The

itemnamemaydifferdependingonyouroperatingsystem.)

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following

describesthestatesoftheLANportLEDs.

ActivityLED

Connection/

SpeedLED

LAN Port

ActivityLED:

Connection/SpeedLED:

State Description

Orange 1 Gbps data rate

Green 100 Mbps data rate

Off 10 Mbps data rate

State Description

Blinking Datatransmissionorreceivingisoccurring

On No data transmission or receiving is occurring

- 11 -

1-7 Internal Connectors

Read the following guidelines before connecting external devices:

•First make sure your devices are compliant with the connectors you wish to connect.

•Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

•After installing the device and before turning on the computer, make sure the device cable has

been securely attached to the connector on the motherboard.

1) ATX_12V_2X4

2) ATX

3) CPU_FAN

4) SYS_FAN1/2

5) CPU_OPT

6) SYS_FAN3_PUMP

7) SATA3 0/1/2/3/4/5

8) M2P_32G/M2Q_32G

9) LED_C1/LED_C2

10) D_LED1/D_LED2

11) DLED_V_SW1/DLED_V_SW2

12) F_ PANEL

13) F_ AUDIO

14) SPDIF_O

15) F_USB30_1/F_USB30_2

16) F_USB1/F_USB2

17) TPM

18) THB_C

19) BAT

20) CLR_CMOS

21) CPU/VGA/DRAM/BOOT

6179 12

10 1113

- 12 -

DEBUG

PORT

G.QBOFM

131

2412

ATX

1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

 Withtheuseofthepowerconnector,thepowersupplycansupplyenoughstablepowertoallthecomponents

onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturned

off and all devices are properly installed. The power connector possesses a foolproof design. Connect the

power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,

the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high

powerconsumptionbeused(500Worgreater).Ifapowersupplyisusedthatdoesnotprovidethe

required power, the result can lead to an unstable or unbootable system.

ATX:

Pin No. Denition Pin No. Denition

1 3.3V 13 3.3V

2 3.3V 14 -12V

3GND 15 GND

4 +5V 16 PS_ON(softOn/Off)

5GND 17 GND

6 +5V 18 GND

7GND 19 GND

8 Power Good 20 NC

95VSB(standby+5V) 21 +5V

10 +12V 22 +5V

11 +12V (Only for 2x12-pin

ATX)

23 +5V(Onlyfor2x12-pinATX)

12 3.3V (Only for 2x12-pin

ATX)

24 GND(Onlyfor2x12-pinATX)

ATX_12V_2X4:

Pin No. Denition Pin No. Denition

1GND(Onlyfor2x4-pin12V) 5+12V(Onlyfor2x4-pin12V)

2GND(Onlyfor2x4-pin12V) 6+12V(Onlyfor2x4-pin12V)

3GND 7 +12V

4GND 8 +12V

3/4) CPU_FAN/SYS_FAN1/2 (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

Whenconnectingafancable,besuretoconnectitinthecorrectorientation(theblackconnectorwireis

thegroundwire).Thespeedcontrolfunctionrequirestheuseofafanwithfanspeedcontroldesign.For

optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

•Be sure to connect fan cables to the fan headers to prevent your CPU and system from

overheating. Overheating may result in damage to the CPU or the system may hang.

•Thesefanheadersarenotcongurationjumperblocks.Donotplaceajumpercapontheheaders.

CPU_FAN

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

ATX_12V_2X4

SYS_FAN1/2

DEBUG

PORT

G.QBOFM

Pin No. Denition

1GND

2 Voltage Speed Control

3 Sense

4PWMSpeedControl

- 13 -

5) CPU_OPT (Water Cooling CPU Fan Header)

The fan header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a foolproof

insertiondesign.Whenconnectingafancable,besuretoconnectitinthecorrectorientation(theblack

connectorwireisthegroundwire).Thespeedcontrolfunctionrequirestheuseofafanwithfanspeed

control design.

DEBUG

PORT

G.QBOFM

7) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA

1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel®ChipsetsupportsRAID0,

RAID1,RAID5,andRAID10.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguring

aRAIDarray.

Pin No. Denition

1GND

2 TXP

3 TXN

4GND

5 RXN

6 RXP

7GND

To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA

AndRSTConguration,"formoreinformation.

DEBUG

PORT

G.QBOFM

6) SYS_FAN3_PUMP (System Fan/Water Cooling Pump Header)

The pump header is 4-pin and possesses a foolproof insertion design. Most fan headers possess a foolproof

insertiondesign.Whenconnectingafancable,besuretoconnectitinthecorrectorientation(theblack

connectorwireisthegroundwire).Thespeedcontrolfunctionrequirestheuseofafanwithfanspeedcontrol

design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

The header also provides speed control for a water cooling pump, refer to Chapter 2, "BIOS Setup," "M.I.T.,"

for more information.

SATA3 3 1

2 0

SATA3 4

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

Pin No. Denition

1GND

2Voltage Speed Control

3Sense

4PWM Speed Control

Pin No. Denition

1GND

2Voltage Speed Control

3Sense

4PWM Speed Control

DEBUG

PORT

G.QBOFM

DEBUG

PORT

G.QBOFM

- 14 -

8) M2P_32G/M2Q_32G (M.2 Socket 3 Connectors)

 TheM.2connectorssupportM.2SATASSDsorM.2PCIeSSDsandsupportRAIDconguration.Please

notethatanM.2PCIeSSDcannotbeusedtocreateaRAIDseteitherwithanM.2SATASSDoraSATA

harddrive.TocreateaRAIDarraywithanM.2PCIeSSD,youmustsetupthecongurationinUEFIBIOS

mode.RefertoChapter3,"ConguringaRAIDSet,"forinstructionsonconguringaRAIDarray.

FollowthestepsbelowtocorrectlyinstallanM.2SSDintheM.2connector.

Step 1:

Use a screw driver to unfasten the screw and nut from the motherboard. Locate the proper mounting hole

fortheM.2SSDtobeinstalledandthenscrewthenutrst.

Step 2:

SlidetheM.2SSDintotheconnectoratanangle.

Step 3:

PresstheM.2SSDdownandthensecureitwiththescrew.

SelecttheproperholefortheM.2SSDtobeinstalledandrefastenthescrewandnut.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

80 60 42

M2Q_32G

M2P_32G

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

80 60110

•M2P_32G:

SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5

M.2SATASSD raaaaa

M.2PCIeSSD

aaaaaa

NoM.2SSDInstalled aaaaaa

a: Available, r: Not available

Connector

Type of

M.2SSD

Installation Notices for the M.2 and SATA Connectors:

DuetothelimitednumberoflanesprovidedbytheChipset,theavailabilityoftheSATAconnectorsmaybe

affected by the type of device installed in the M2P_32G connector. The M2P_32G connector shares bandwidth

with the SATA3 0 connector. Refer to the following tables for details.

•M2Q_32G:

SATA3 0 SATA3 1 SATA3 2 SATA3 3 SATA3 4 SATA3 5

M.2PCIeSSD*

aaaaaa

NoM.2SSDInstalled aaaaaa

a: Available, r: Not available

* TheM2Q_32GconnectorsupportsonlyPCIeSSDs.

Connector

Type of

M.2SSD

- 15 -

9) LED_C1/LED_C2 (RGB (RGBW) LED Strip Headers)

 Theheaderscanbeusedtoconnectastandard5050RGB(RGBW)LEDstrip(12V/G/R/B/W),with

maximumpowerratingof2A(12V)andmaximumlengthof2m.

Pin No. Denition

1 12V

2 G

3 R

4 B

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

LED_C1

LED_C2

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

Forhowtoturnon/offthelightsoftheLEDstrip,refertotheinstructionsoninChapter2,"BIOS

Setup," "Peripherals."

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power

cord from the power outlet to prevent damage to the devices.

ConnectyourdigitalLEDstriptotheheader.Thereare12Vand5VdigitalLEDstrips.Besuretoverify

thevoltagerequirementsofyourdigitalLEDstripsandsettheDLED_V_SW1andDLED_V_SW2jumpers

accordingly.Thepowerpin(markedwithatriangleontheplug)oftheLEDstripmustbeconnectedtoPin

1ofthedigitalLEDstripheader.IncorrectconnectionmayleadtothedamageoftheLEDstrip.

Forhowtoturnon/offthelightsoftheLEDstrip,refertotheinstructionsoninChapter2,"BIOS

Setup," "Peripherals."

10) D_LED1/D_LED2 (Digital LED Strip Headers)

 Theheaderscanbeusedtoconnectastandard5050digitalLEDstrip,withmaximumpowerratingof2A

(12Vor5V)andmaximumlengthof5mormaximumnumberof300LEDs.

DigitalLEDStrip

11) DLED_V_SW1/DLED_V_SW2 (Digital LED Strip Power Select Jumpers)

 ThejumpersallowyoutoselectthesupplyvoltageoftheD_LED1andD_LED2headers.Besureto

verifythevoltagerequirementsofyourdigitalLEDstripandsetthecorrectvoltagewiththisjumperbefore

connection.IncorrectconnectionmayleadtothedamageoftheLEDstrip.

ConnectyourRGB(RGBW)LEDstriptotheheader.Thepowerpin

(markedwithatriangleontheplug)oftheLEDstripmustbeconnected

toPin1(12V)ofthisheader.Incorrectconnectionmayleadtothe

damageoftheLEDstrip.

RGBW

LEDStrip

12V

RGB

LEDStrip

Pin No. Denition

1 V

3 G

D_LED1 D_LED2

1-2: 5V 1-2: 5V

2-3: 12V 2-3: 12V

DLED_V_SW1 DLED_V_SW2

- 16 -

The front panel design may differ by chassis. A front panel module mainly consists of power switch,

resetswitch,powerLED,harddriveactivityLED,speakerandetc.Whenconnectingyourchassis

front panel module to this header, make sure the wire assignments and the pin assignments are

matched correctly.

12) F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator

on the chassis to this header according to the pin assignments below. Note the positive and negative pins

before connecting the cables.

System Status LED

S0 On

S3/S4/S5 Off

•PW(PowerSwitch,Red):

Connects to the power switch on the chassis front panel. You may

congurethewaytoturnoffyoursystemusingthepowerswitch(refer

toChapter2,"BIOSSetup,""Power,"formoreinformation).

•SPEAK (Speaker,Orange):

Connects to the speaker on the chassis front panel. The system reports

system startup status by issuing a beep code. One single short beep

will be heard if no problem is detected at system startup.

•PLED/PWR_LED (PowerLED,Yellow/Purple):

Connects to the power status indicator

onthechassisfrontpanel.TheLEDison

whenthesystemisoperating.TheLEDis

off when the system is in S3/S4 sleep state

orpoweredoff(S5).

•HD (HardDriveActivityLED,Blue):

 ConnectstotheharddriveactivityLEDonthechassisfrontpanel.TheLEDisonwhentheharddrive

is reading or writing data.

•RES (ResetSwitch,Green):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer

ifthecomputerfreezesandfailstoperformanormalrestart.

•CI (ChassisIntrusionHeader,Gray):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has

been removed. This function requires a chassis with a chassis intrusion switch/sensor.

•NC (Orange):NoConnection.

13) F_AUDIO (Front Panel Audio Header)

 ThefrontpanelaudioheadersupportsIntelHighDenitionaudio(HD).Youmayconnectyourchassis

front panel audio module to this header. Make sure the wire assignments of the module connector match

the pin assignments of the motherboard header. Incorrect connection between the module connector and

the motherboard header will make the device unable to work or even damage it.

Some chassis provide a front panel audio module that has separated connectors on each wire

instead of a single plug. For information about connecting the front panel audio module that has

different wire assignments, please contact the chassis manufacturer.

Pin No. Denition

1 MIC2_L

2GND

3 MIC2_R

4 NC

5 LINE2_R

6 Sense

7FAUDIO_JD

8 No Pin

9 LINE2_L

10 Sense

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

9 1

10 2

PowerLED

DEBUG

PORT

G.QBOFM

CI-

CI+

PWR_LED-

PWR_LED+

PLED-

PW-

SPEAK+

SPEAK-

PLED+

PW+

PowerLED

HD-

RES+

HD+

RES-

HardDrive

ActivityLED

Reset

Switch Chassis Intrusion

Header

Power Switch Speaker

PWR_LED-

- 17 -

14) SPDIF_O (S/PDIF Out Header)

This header supports digital S/PDIF Out and connects a S/PDIF digital audio cable (provided by expansion

cards) for digital audio output from your motherboard to certain expansion cards like graphics cards and

sound cards. For example, some graphics cards may require you to use a S/PDIF digital audio cable for

digital audio output from your motherboard to your graphics card if you wish to connect an HDMI display

to the graphics card and have digital audio output from the HDMI display at the same time. For information

about connecting the S/PDIF digital audio cable, carefully read the manual for your expansion card.

Pin No. Denition

15VDUAL

2 No Pin

3 SPDIFO

4 GND

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

Pin No. Denition Pin No. Denition

1 VBUS 11 D2+

2 SSRX1- 12 D2-

3 SSRX1+ 13 GND

4GND 14 SSTX2+

5 SSTX1- 15 SSTX2-

6 SSTX1+ 16 GND

7GND 17 SSRX2+

8D1- 18 SSRX2-

9D1+ 19 VBUS

10 NC 20 No Pin

15) F_USB30_1/F_USB30_2 (USB 3.1 Gen 1 Headers)

The headers conform to USB 3.1 Gen 1 and USB 2.0 specication and each header can provide two USB

ports. For purchasing the optional 3.5" front panel that provides two USB 3.1 Gen 1 ports, please contact

the local dealer.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

20 1

Prior to installing the USB front panel, be sure to turn off your computer and unplug the power cord

from the power outlet to prevent damage to the USB front panel.

16) F_USB1/F_USB2 (USB 2.0/1.1 Headers)

 TheheadersconformtoUSB2.0/1.1specication.EachUSBheadercanprovidetwoUSBportsviaan

optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer.

Pin No. Denition Pin No. Denition

1Power(5V) 6USBDY+

2Power(5V) 7GND

3USBDX- 8GND

4USBDY- 9 No Pin

5USBDX+ 10 NC

•DonotplugtheIEEE1394bracket(2x5-pin)cableintotheUSB2.0/1.1header.

•Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord

from the power outlet to prevent damage to the USB bracket.

DEBUG

PORT

G.QBOFM

- 18 -

17) TPM (Trusted Platform Module Header)

 YoumayconnectaTPM(TrustedPlatformModule)tothisheader.

11 1

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

Pin No. Denition Pin No. Denition

1LAD0 7LAD3

2 VCC3 8 GND

3LAD1 9 LFRAME

4 No Pin 10 NC

5LAD2 11 SERIRQ

6 LCLK 12 LRESET

12 2

18) THB_C (Thunderbolt™ Add-in Card Connector)

This connector is for a GIGABYTE Thunderbolt™ add-in card.

Supports a Thunderbolt™ add-in card.

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

19) BAT (Battery)

 Thebatteryprovidespowertokeepthevalues(suchasBIOScongurations,date,andtimeinformation)

in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low

level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.

2. Gently remove the battery from the battery holder and wait for one minute. (Or

use a metal object like a screwdriver to touch the positive and negative terminals

ofthebatteryholder,makingthemshortfor5seconds.)

3. Replace the battery.

4. Plug in the power cord and restart your computer.

•Always turn off your computer and unplug the power cord before replacing the battery.

•Replacethebatterywithanequivalentone.Damagetoyourdevicesmayoccurifthebattery

is replaced with an incorrect model.

•Contact the place of purchase or local dealer if you are not able to replace the battery by yourself

or uncertain about the battery model.

•Wheninstallingthebattery,notetheorientationofthepositiveside(+)andthenegativeside(-)

ofthebattery(thepositivesideshouldfaceup).

•Used batteries must be handled in accordance with local environmental regulations.

- 19 -

20) CLR_CMOS (Clear CMOS Jumper)

 UsethisjumpertocleartheBIOScongurationandresettheCMOSvaluestofactorydefaults.Toclear

the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

•Always turn off your computer and unplug the power cord from the power outlet before clearing

the CMOS values.

•Aftersystemrestart,gotoBIOSSetuptoloadfactorydefaults(selectLoadOptimizedDefaults)or

manuallyconguretheBIOSsettings(refertoChapter2,"BIOSSetup,"forBIOScongurations).

Open: Normal

Short: Clear CMOS Values

21) CPU/VGA/DRAM/BOOT (Status LEDs)

 ThestatusLEDs showwhetherthe CPU,graphicscard, memory,and operatingsystem are working

properlyaftersystempower-on.IftheCPU/VGA/DRAMLEDison,thatmeansthecorrespondingdevice

isnotworkingnormally;iftheBOOTLEDison,thatmeansyouhaven'tenteredtheoperatingsystemyet.

CPU: CPUstatusLED

VGA: GraphicscardstatusLED

DRAM: MemorystatusLED

BOOT: OperatingsystemstatusLED

F_USB30 F_U

B_ 

F_  F_ 



_

B

BS_

B

SB_

B

_S



S_

_

B

_U

_

B





 

S  

 

123

 

123

 

123

 

123

BSS

S

_S 

SSU

 

1 2 3  

 S3 BSSS



U

 __ 3

F_USB3F

S  _

SF





B_

F

_0

S

S

_0F

_F

_

_

__B





U

S  _S

_ SF_

USB0_B

B_ F_USB3





_



_3U

CPU DRAM

VGA BOOT

- 20 -

Page is loading ...

Gigabyte Z370 AORUS GAMING K3 User manual

Gigabyte Z370 AORUS GAMING K3 User manual

Gigabyte Z370 AORUS GAMING K3 User manual

Related papers

Other documents