Schweigen PKCL8815SP2 User manual

Brand: Schweigen

Model: PKCL8815SP2

Type: User manual

This manual is also suitable for

www.schweigen.com.au

RANGEHOOD & INSTALLATION GUIDE

CL7275S

Revision V4 01/10/21

Page 2

Index

1. Welcome 3

Your State Regulatory Authority 3

2. Important Safety Information 4

Before Installation 5

Product Use 6

Ducted or Recirculating? 6

Maintenance and Service 6

Cleaning the Bae Filters 6

Electrical Cord 6

3. Description 7

Rangehood 7

4. Operation 8

Push Button Control Panel 8

Speed Control 8

5. Cleaning & Maintenance 9

Surfaces 9

Filters 9

Cleaning the Interior 10

Cleaning the Exterior 10

Replacing the Light Bulb 11

6. Installation 12

Rangehood Size vs Cooktop Size 12

BBQ Installation 12

Mounting Instructions – Outdoor/Alfresco 13

Wall Mount Installation 14

Ducting 17

Back Draft Fins (For applicable models) 17

Ducting Advice 18

Roof Cowls / Roof Seal Kit 19

7. Troubleshooting 20

Troubleshooting 20

Service 21

Faulty Installation 21

8. Specications 22

Dimensions 22

Technical Specications 22

9. Disclaimer 23

Page 3

1. Welcome

Thank you for purchasing your new Schweigen rangehood.

To get the maximum output from this unit, please read through this guide before use.

The guide contains important information on the use and maintenance of the unit, as well as important

safety notes. This will ensure your personal safety and the lasting value of your rangehood.

Please always retain your proof of purchase to aid in any warranty queries.

If you are unable to locate your warranty card, one is available to download from our website

www.schweigen.com.au.

This appliance and its packaging are produced by processes that minimise waste and respect

the environment.

Please help us to continue this eort to protect the environment by using the appliance eciently

and dispose of the packaging in a responsible manner.

We trust that you will enjoy your new Schweigen rangehood.

Your State Regulatory Authority

Dierent Australian states have varying legislative requirements for the installation of rangehood

ducting. Some will insist on ducting being vented externally (i.e. not in to the ceiling cavity); others

will not. It is imperative that you check with your state building authority and/or private certier

to conrm their position.

Page 4

2. Important Safety Information

WARNING

Please read this section thoroughly before attempting to operate the appliance.

Inspect your product upon receipt. Any damage or defects MUST be reported

within 48 hours, or no claim will be recognised.

DO NOT INSTALL THIS APPLIANCE IF YOU FIND IT DAMAGED.

If this product is installed damaged, neither the supplier, nor the retailer, will be

responsible for the costs associated with the repair, replacement, removal or

re-installation of the appliances.

1. To be installed in an undercover alfresco area only.

2. If the unit is not adequately covered or sheltered from the outside elements the warranty

will be null and void.

3. There shall be adequate ventilation in the room when the rangehood is used at the same time

as appliances burning gas or other fuels.

4. There is a re risk if cleaning is not carried out in accordance with the instructions.

5. Do not ambé under the rangehood. This will damage the rangehood and will not be covered by warranty.

6. Do not ignite burners that give o intense, uncontrolled ames beneath the rangehood.

7. Make sure that no ames emerge from the sides of pans.

8. Do not leave packaging materials (bags, corner brackets, etc.) within reach of children.

9. This appliance is not intended for use by person/s (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and/or knowledge. Unless the person has

been given supervision or instruction concerning the use of the appliance by a person responsible

for their safety. Children should be supervised to ensure that they do not play with the appliance,

it is not a toy.

10. Exhaust air must not be discharged into an existing ue that is used for exhausting fumes from

appliances burning gas or other fuels.

11. Air exhaust must be installed in accordance with local laws. Regulations concerning the discharge

of air have to be fullled.

12. Accessible parts may become hot when used with cooking appliances.

13. Before performing any cleaning or maintenance operation, disconnect the rangehood from

the mains using the respective mains or sector switch or by unplugging it.

14. Do not use the rangehood without the grease lters.

15. Keep the grease lters clean and respect the recommended cleaning frequencies.

16. Turn the rangehood motor on before starting to cook.

17. Turn the rangehood motor o about 10-15 minutes after you nish cooking.

Page 5

2. Important Safety Information

18. It is forbidden to use the rangehood as an aspirator.

19. Never cook foodstu directly over the ame or have the gas burners on under the rangehood

without using cookware.

Before Installation

1. We recommend this appliance be installed or repaired by a qualied Schweigen Home Appliances

technician.

2. Please see our website www.schweigen.com.au for recommended installers.

3. It is dangerous to modify any part of this appliance. Modication of any kind, will immediately void the

warranty.

4. The manufacturer declines all responsibility in case of failure to adopt proper safety measures.

5. Ensure that the location in which this appliance is installed, has good and permanent ventilation.

6. Please consult local laws and regulations and install in accordance.

7. Use an electrical connector with earth that is correct for your location.

8. Check that the voltage in your area corresponds to the appliance as indicated on the rating label.

9. This appliance must be connected to an electricity supply with a ground connection.

10. Check that the installation and electrical connections are made by a qualied technician and that the

indicated instructions and local regulations in force are met, using materials that are compliant with

the applicable legislation.

11. The company will not be responsible for installations executed by non-qualied sta and

installations that fail to heed the applicable legislation on electrical safety (with regard to both

modes and materials).

12. The electrical technical data can be found inside the rangehood, after removing the grease lters.

13. The exible power cable supplied is already connected internally and emerges from the rangehood

near the air outlet tube.

14. Before installing the electrical connections, you should:

–Verify that the indicated electrical data coincide with the voltage values and frequency

of the electrical circuit in the house where the rangehood is to be installed;

–Check that the premises has electrical protection against short circuits and electrocution,

pursuant to the applicable legislation;

–Always switch o the current using the double-pole switch before maintenance and turn

the power on again for normal use only when the operation has been completed.

Page 6

2. Important Safety Information

Product Use

This product is designed for household use and should not be used for commercial applications.

After use, always ensure that all controls are in the “OFF” position.

When frying with a gas ame, take particular care not to allow the oil or grease in the pan to catch

re. (Flambé)

Electrical Cord

Ensure the supply cord is not exposed to heat, chemicals or sharp objects. If the supply cord is damaged,

it must be replaced by the manufacturer.

Page 7

Rangehood

1. Mounting Bracket

2. Upper Flue

3. Lower Flue

4. For use with Isodrive® motor system

5. Power Cord

6. Rangehood Body

7. Baes

8. Lights

9. Remote Control

NOTE: Filter and light quantity may vary from

model to model.

3. Description

Page 8

4. Operation

TOUCH BUTTON CONTROL PANEL

Remote control sensor

Turn light on/off

Fan speed setting

Turn rangehood on/off

REMOTE CONTROL

As well as the touch buttons, this undermount rangehood comes

with a remote control to operate the rangehood.

1. Use this button for activating and deactivating the motor.

2. Changes the speed of the motor (minimum level is 1, maximum is 4.)

3. Automatically changes the speed to maximum or minimum speed.

4. Turns the lights on or off.

5. 15 minute timer.

NOTE: If there is no change in operation to the unit in 4 hours,

it will shut down all functions, including lights and extraction fans

(available on certain models only).

USING THE ON BUTTON

The first time press the on button, you turn the rangehood on, the second time when you press the

on button it goes to 10min timer, the third time you press it, the rangehood is turned off.

SPEED CONTROL

This undermount is equipped with a 5 speed touch control.

Speed control usage suggestions:

• Low speed for simmering.

• Medium speed for light cooking.

• High speed for heavy frying/cooking.

Page 9

5. Cleaning & Maintenance

Cleaning the Interior

Clean the interior of the rangehood with a damp cloth and a neutral detergent or denatured alcohol.

NOTE: Do not use denatured alcohol on the exterior of the rangehood. Do not clean the electric parts or

the motor with liquids or solvents

Cleaning the Exterior

We recommended using a soft cloth, water and a liquid soap, rinsing it well and then drying it thoroughly.

For better results, you can use high quality cleaning and protection products (e.g. Steel Kleen) to clean

your rangehood.

• The recommended detergent is a solution of water and a neutral

liquid soap.

• It is very important for the liquid soap to not contain granules

that could scratch the surface.

• First apply the solution to a soft cloth and then rub the cloth

over the rangehood. It is important to follow the direction of the

stained surface with the cloth (refer to gure on left).

• Do not pour any liquid directly on to the rangehood.

• The cloth must have no buttons, zips or fasteners that could

scratch the surface.

• It is strictly forbidden to use chemical solvents, aggressive,

grainy or abrasive products, naphtha, alcohol or similar products

that could damage the surface of the rangehood.

• The manufacturer will not be held responsible for functional or

aesthetic damage caused by cleaning with products which are

not suitable or using inadequate cleaning methods.

Warning

Always switch o and disconnect power before cleaning.

Page 10

5. Cleaning & Maintenance

Endure the baes are cool before removing, to

ensure no oil is spilt.

To remove, push away from you until the near

edge clears the slot. Then carefully pull down

and back to remove. To replace, perform the

same operation but in reverse.

Baes

For this appliance to function eectively, regular maintenance is a must.

• The function of the bae is to collect the grease particles given o during cooking.

• Clogged heavy oil deposits restrict airow and may cause the motor to overheat

and become a re hazard.

• Baes should be cleaned every 3-6 weeks or after 40 hours of use.

• For induction cooktop, please aim to clean them at least every 10 days, depending on use.

• The baes can be washed by hand or in the dishwasher.

–Washing by hand - Immerse the lter in hot water and a suitable detergent and when clean,

rinse with plenty of hot water.

–Dishwasher - Put the lter in the dishwasher and select a short program at low temperature.

NOTE: The colour of the metal mesh lters may change after several washes. This is normal and

it is not necessary to change the lters.

Please ensure the baes are completely dry before placing them back in position

and operating the rangehood.

Warning

• If the baes are very dirty, the motor will extract only a small quantity of air, which

reduces its eciency;

• The grease deposits that build up on the baes are highly ammable and COULD

EASILY CATCH FIRE.

• The manufacturer is exonerated from all responsibility in the event of re due to poor

maintenance of the grease lters.

Page 11

5. Cleaning & Maintenance

Danger

Always switch o and disconnect the power cord before replacing any light bulbs. Failure

to do so may cause serious injury. Please be aware that the light bulb will retain heat for

a short period of time after being switched o.

Replacing the Light Bulb

Step 2

Gently turn light bulb clockwise,

pull the light bulb down and

remove it from the light holder.

Step 3

Insert a new light bulb by lining

up the pins of the light bulb with

the larger holes inside the light

holder. Once the pins are in place,

turn anti-clockwise to secure the

light bulb.

Step 1

Remove the lters from

the rangehood.

Page 12

6. Installation

Rangehood Size vs Cooktop Size

In addition to the size, the height of the rangehood above the cooktop is important to obtain

the best performance.

INADEQUATE

Rangehood smaller than

cooking zone

ADEQUATE

Rangehood same size as

cooking zone

OPTIMAL

Rangehood larger than

cooking zone

BBQ Installation

When installing the rangehood over a BBQ , please be aware that the lid will obstruct the rangehoods

eectiveness to extract smoke, steam and odours. Where possible, remove the lid of the BBQ unit when

in use, so as to allow for eective rangehood extraction. Alternatively, install the rangehood on an

extension, to move the rangehood further out.

Extension

_n_. _RH Section_

Page 13

6. Installation

Mounting Instructions – Outdoor/Alfresco

When installing in an outdoor kitchen or alfresco area,the rangehood MUST NOT be installed

where it is directly exposed to the elements .

It is STRONGLY RECOMMENDED that the rangehood be installed centrally over the cooktop.

This will greatly improve its performance.

Minimum legal height from the BBQ surface to the underside face of the rangehood:

• 1200mm

Any installation above 1200mm will compromise the extraction performance.

Measurements are from the top of the trivets to the lowest part of the rangehood,

including the button controls.

*IMPORTANT: If the user decides to install the rangehood at a distance of less than minimum height

above the cooking surface, Schweigen declines responsibility for damages suered by the rangehood

due to excess heat or damage to objects, people and others caused directly or indirectly by a

malfunction, breakage or re.

* Important: In addition to the information in this manual,

please check all relevant state requirememnts for minimum–

maximum heights, as well as regulations regarding the

expelling of air. Schweigen is not liable if your rangehood is

not installed in accordance with these legal requirements.

_n_. _LH Section_

Page 14

6. Installation

Wall Mount Installation

There are two primary mounting points and several secondary mounting points to rmly x the

rangehood in place.

Suitable xing screws must be used to mount the appliance on a secure surface.

Please ensure that the holes for the two primary mounting points are level before installation.

1. Primary Mounting Points

2. Secondary Mounting Points

1 1

22 2

240

780

540.25

750

721

DANGER

Always switch o and disconnect the power supply before installing the rangehood.

Failure to do so may cause serious injury.

WARNING

Please remove lters before installation. Failure to do so may damage the clips.

_n_. _RH Section_

Page 15

6. Installation

Step 1

Secure rangehood to the wall using only primary

mounting points ( 1). Check the level of the

rangehood and adjust accordingly if necessary

(2). Once level, continue to secure the rangehood

via the secondary mounting points ( 3).

Step 2

Feed through and secure the exi ducting from

the rangehood outlet to the Isodrive motor.

Installation Example

Page 16

6. Installation

Step 3

Place ue covers on the rangehood and extend

to the length required. (Be careful not to scratch

the top of the rangehood).

PLEASE NOTE: Only a standard length of

stainless steel ue is provided. Any additional

length will need to be sourced and manufactured

by a sheet metal fabricator.

Step 4

Attach the exterior ue wall mounting bracket to

the wall. Slide the inside extension ue piece up

to the wall mounting bracket and secure.

NOTE

Remove all plastic protection on the rangehood and lters before use.

Page 17

6. Installation

Ducting

Please DO NOT crush or kink the ducting.

1. Crushed or kinked ducting creates

sharp corners that creates turbulence.

This reduces the size and eciency

of the ducting, lowers extraction and

may cause excessive noise.

2. Sweeping curves and taut ducting

reduces resistance and turbulence.

The airow and extraction will be

more ecient and stronger.

Back Draft Fins (For applicable models)

The supplied ducting has been manufactured with an allowance for the back draft ns to operate without

hindrance. It is the smooth extended end of the ducting.

When installing Back Draft Fins, please ensure that you insert the Back Draft Fins onto the back draft base,

which are attached to the top of the motor outlet before installation. Then place the smooth extended edge

of the ducting into the back draft base and x securely.

Should your Back Draft Fins get stuck, this is not a warranty issue.

Back Draft Fins Back Draft Fins

open position Back Draft Fins

ducting

Allowance for

Back Draft Fins

Back Draft Base

Page 18

6. Installation

Isodrive® Motor Setup

Note

Please refer to the Isodrive® motor installation guide for more details

on exi ducting and Isodrive® motor installation.

Page 19

6. Installation

Single Isodrive® Motor Installation

1. Isodrive® Motor

2. Roof Seal Kit (Dektite) (Not supplied)*

3. Support Straps (Not supplied)*

4. Attach Flexi Duct to Bell-Mouth Adaptor

using ring clamp. Please DO NOT rip

the ducting.

5. Isodrive® Motor Power Lead (Male Plug)

6. Rangehood to Isodrive® Motor Lead

(Female Plug)

7. Multi-t Y-Joint, cut to 200 x 200 x 200mm

8. Mains power

9. Flexi Ducting must be pulled taut.

DO NOT crush or kink the ducting.

10. Connect exi ducting to the outlet

on rangehood using ring clamp.

Please DO NOT rip the ducting.

910

200mm

Flexi Duct

200mm

Flexi Duct

DANGER

All electrical wiring from the motor to the rangehood should be kept inside the roof space.

NOTE

The Isodrive® motor system does not include the roof seal kit, cable ties, ring clamp

or the support straps.

NOTE

The general power outlet for the rangehood should be located in an easy to access area.

Page 20

Twin Isodrive® Motor Installation

1. Isodrive® Motors

2. Roof Seal Kit (Dektite) (Not supplied)*

3. Support Straps (Not supplied)*

4. Attach Flexi Duct to Bell-Mouth Adaptor

using ring clamp. Please DO NOT rip

the ducting.

5. Isodrive® Motor Power Lead (Male Plug)

6. Rangehood to Isodrive® Motor Lead

(Female Plug)

7. Mains power

8. Flexi Ducting must be pulled taut.

DO NOT crush or kink the ducting.

9. Connect exi ducting to the outlet

on rangehood using ring clamp.

Please DO NOT rip the ducting.

8 9

DANGER

All electrical wiring from the motor to the rangehood should be kept inside the roof space.

NOTE

The Isodrive® motor system does not include the roof seal kit, cable ties, ring clamp

or the support straps.

NOTE

The general power outlet for the rangehood should be located in an easy to access area.

Rangehood to Motor power

leads are to be hard wired

by an electrician.

6. Installation

Page is loading ...

Schweigen PKCL8815SP2 User manual

Brand: Schweigen

Model: PKCL8815SP2

Type: User manual

This manual is also suitable for

Download PDF

report

Schweigen PKCL8815SP2 User manual

This manual is also suitable for

Schweigen PKCL8815SP2 User manual

Related papers

Other documents