Performax 241-0944 Owner's manual
- Category
- Power tools
- Type
- Owner's manual
PRODUCT SPECIFICATIONS
Rated Power : 5.8A
Max. Cutting Depth : (90⁰) : 1-3/4"
(45⁰) : 1-1/8"
No Load Speed : 3500/min(no load)
Blade Size : 4-1/2"×3/8"×24T
Need Assistance ?
Call us on our toll free customer support line :
1-866-915-8626
• Technical questions
• Replacement parts
• Parts missing from package
4-1/2" Compact
Circular saw
241-0944
Owner's Manual
2
TABLE OF CONTENTS
General Safety Rules.................................................................................... Page 2
Specific Safety Rules................................................................................... Page 4
Symbols....................................................................................................... Page 6
Electrical...................................................................................................... Page 7
Features....................................................................................................... Page 8
Overview Components................................................................................. Page 9
Assembly...................................................................................................... Page 9
Operation..................................................................................................... Page 12
Maintenance................................................................................................ Page 14
Parts list....................................................................................................... Page 15
Exploded view.............................................................................................. Page 17
Warranty....................................................................................................... Page 18
GENERAL SAFETY RULES
WARNING :
Remove the plug from the socket before carrying out any adjustment, servicing or
maintenance. Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious injury.
Make sure the voltage corresponds to the type label on the unit. Packing materials
are not toys! Children must not play with plastic bags! Danger of suffocation! The
power tool noise output may exceed 85dB(A) at the workplace. In this instance, wear
ear protection.
WARNING :
Read all enclosed safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/
or serious injury. The term “power tool” in the warnings refers to your power tool or
battery operated (cordless) power tool.
Save all warnings and instructions for future reference.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of ammable liq-
uids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
3
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrig-
erators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges and moving parts. Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) pro-
tected supply. Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not
use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective equipment such as
dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will
reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your nger on
the switch or energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left at-
tached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety mea-
sures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of
untrained users.
4
e) Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. In accordance with these instructions, taking into
account the working conditions and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one
type of battery pack may create a risk of re when used with another battery pack.
b) Use power tools only with specically designated battery packs. Use of any other battery packs
may create a risk of injury and re.
c) When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys,
nails, screws, or other small metal objects that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact acciden-
tally occurs, ush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
6) Service
a) Have your power tool serviced by a qualied repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
b) When servicing a power tool, use only identical replacement parts. Follow instructions in the Main-
tenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instruc-
tions may create a risk of shock or injury.
WARNING
To reduce the risk of injury, user must read the instruction manual.
5
SPECIFIC SAFETY RULES
WARNING
Keep hands away from the cutting area and blade. NEVER place your hands behind
the saw blade since kickback could cause the saw to jump backwards over your
hand. Keep your body positioned to either side of the saw blade.
SAVE THESE INSTRUCTIONS
- Check the lower guard for proper closing before each use. If the saw is accidentally dropped, the
lower guard may be bent. Raise the lower guard with the lower guard lever and make sure it can
move freely and does not touch the blade or any other parts in all angles and depths of cutting. Do
not operate the saw if the lower guard does not move and close freely. Never clamp or tie the lower
guard into the open position.
- Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
- Never hold piece being cut in your hands or across your leg. Secure the workpiece to a stable plat-
form. It is important to support the work properly to minimize body exposure, blade binding, or loss
of control.
- Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of
the tool “live” and shock the operator.
- Always observe the lower guard to see if it covers the entire blade before placing the saw on the
bench or oor. Please pay attention to the time it needs to take for the blade to stop after released
the switch.
- When operating the saw, keep the cord away from the cutting area and position so that it might be
caught by the work piece during the cutting operation.
- Keep your second hand on the motor housing or auxiliary handle, not close to the blade. Do not
reach underneath the work or attempt to remove the cutting material when the blade is still moving.
- It is important to support the work properly and to hold the saw rmly to prevent from loss of con-
trol, which might cause personal injury. NEVER hold the pieces for cutting in your hands or across
your legs.
- Making a “Pocket Cut” into existing walls or other blind area is dangerous. The protruding blade
may cut “live wires” or objects that may cause kickback.
- When cutting is interrupted or the blade bound, please release the trigger immediately and hold
the saw firmly in the material until the blade comes to a complete stop. Never attempt to remove the
saw from the work or pull the saw backward while the blade is in motion, otherwise, kickback might
happen.
- Use a rip fence or straight edge guide when ripping.
- Avoid cutting nails, inspect the material that is being cut to see if there are nails in it and remove
before cutting.
- Do not run the saw while carrying it at your side.
- Make sure the depth and bevel adjusting locking levers are tight and secure before making a cut.
- Do not use damaged or dull blades. Because unshaped or improperly set blades will produce nar-
row Nerf which may cause excessive friction, blade binding or kickback etc.
- Always use blades with correct size arbor holes, never use defective or incorrect blade washers or
bolts.
6
KICKBACK
Kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the operator.
- When a blade is pinched or bound tightly by the Nerf closing down, the blade stalls and the motor
reaction may drive the unit back toward the operator rapidly.
- If the blade is twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into
the top surface of the wood which may cause the blade to climb out of the Nerf or jump back toward
the operator.
- Using dull blades or improperly supported work will increase the tendency of kickback.
- To prevent kickback, wet lumber, green lumber or pressure treated lumber all require special atten-
tion during cutting operations.
Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
- Maintain a rm grip on the saw and position your arm to resist kickback forces. Position your body
to either side of the blade, but not in line with the blade. Kickback could cause the saw to jump
backwards, but kickback force can be controlled by the operator, if proper precautions are taken.
- When a blade is binding, or when interrupting a cut for any reason, release the trigger and hold the
saw motionless in the material until the blade comes to a complete stop. Never attempt to remove
the saw from the work or pull the saw backward while the blade is in motion or kickback may occur.
Investigate and take corrective actions to eliminate the cause of blade binding.
- When restarting a saw in the workpiece, center the saw blade in the Nerf and check that saw
teeth are not engaged into the material. If saw blade is binding, it may walk up or kickback from the
workpiece as the saw is restarted.
- Support large panels to minimize the risk of blade pinching and kickback. Large panels tend to sag
under their own weight. Support must be placed under the panel on both sides, near the line of cut
and near the edge of the panel.
Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow Nerf
causing excessive friction, blade binding and kickback.
- Blade depth and bevel adjusting locking levers must be tight and secure before making a cut. If
blade adjustment shifts while cutting, it may cause binding and kickback.
- Use extra caution when making a “plunge cut” into existing walls or other blind areas. The
protruding blade may cut objects that can cause kickback.
7
Safety instruction for saws
- Check lower guard before each use. Do not operate the saw if the lower guard does not move freely
and close instantly. Never clamp or tie the lower guard into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the lower guard with the retracting handle and make sure
it moves freely and does not touch the blade or any other part, in all angles and depth of cut.
- Check the operation of the lower guard spring. If the guard and the spring are not operating
properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged
parts, gummy deposits, or a build-up of debris.
- Lower guard should be retracted manually only for special cuts such as “plunge cuts” and
“compound cuts”. Raise lower guard by retracting handle and as soon as blade enters the
material, the lower guard must be released. For all other sawing, the lower guard should operate
automatically.
- Always observe that the lower guard is covering the blade before placing saw down on bench or
oor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to stop after switch is released.
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with
this product.
WARNING :
Indicates an imminently hazardous situation which, if not avoided, will result in
death or serious injury.
CAUTION :
Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
CAUTION :
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and
safer.
8
Symbol Description DESIGNATION/EXPLANATION
Safety Alert Indicates a potential personal
injury hazard.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes Time
~ Alternating Current Type of current
No No Load Speed Rotational speed, at no load
Class II Tool Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per
minute
Wet Conditions Alert Do not expose to rain or use
in damp locations.
Read the operater's manual To reduce the risk of injury, user must read and
understand operator’s manual before using this
product.
Eye Protection Always wear eye protection with
side shields marked to comply
with ANSI Z87.1.
ELECTRICAL
DOUBLE ISOLATION
Double insulation is a concept in safety in electric power tools, which eliminates the need for the
usual three-wire grounded power cord. All exposed metal parts are isolated from the internal metal
motor components with protecting insulation. Double insulated tools do not need to be grounded.
WARNING :
The double insulated system is intended to protect the user from shock resulting
from a break in the tool’s internal wiring. Observe all normal safety precautions to
avoid electrical shock.
NOTE :
Servicing of a tool with double insulation requires extreme care and knowledge
of the system and should be performed only by a qualified service technician. For
service, we suggest you return the tool to your nearest authorized service center for
repair. Always use original factory replacement parts when servicing.
9
ELECTRIC CONNECTION
This tool has a precision-built electric motor. It should be connected to a power supply that is 120
volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A
substantial voltage drop will cause a loss of power and the motor will overheat. If your tool does not
operate when plugged into an outlet, double-check the power supply.
EXTENSION CORDS
When using a power tool at a considerable distance from a power source, be sure to use an extension
cord that has the capacity to handle the current the tool will draw. An undersized cord will cause a
drop in line voltage, resulting in overheating and loss of power. Use the chart to determine the mini-
mum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Labo-
ratories (UL) should be used.
When working outdoors with a tool, use an extension cord that is designed for outside use. This type
of cord is designated with “WA” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or exposed wires and cut or worn insulation.
** Ampere rating ( on faceplate )
0 ~ 2 2.1 ~ 3.4 3.5 ~ 5 5.1 ~ 7 7.1 ~ 12 12.1 ~ 16
Cord lenght Wire size according A.W.G. ( Amercian wire gauge )
25' 16 16 16 16 14 14
50' 16 16 16 14 14 12
100' 16 16 14 12 10 -
Table 1 : minimum wire size required in an extension cord.
**Used on 12 gauge - 20 amp circuit.
WARNING :
Keep the extension cord clear of the working area. Position the cord so that it will
not get caught on lumber, tools or other obstructions while you are working with a
power tool. Failure to do so can result in serious personal injury.
WARNING :
Check extension cords before each use. If damaged replace immediately. Never use
tool with a damaged cord since touching the damaged area could cause electrical
shock resulting in serious injury.
10
OVERVIEW COMPONENTS
A - Saw blade K - Lower guard
B - Switch L - Base plate
C - Lock button M - Storage for hexagon key
D - Upper guard N - Spindle lock
E - Angle locking lever O - Depth locking lever
F - Parallel guide lock screw P - Depth scale
G - Parallel guide Q - Dust outlet
H - Clamping flange R - Dust pipe
I - Clamping screw S - Machine housing
J - Lower guard guide lever
ASSEMBLY
Check for damage to the tool, parts and accessories which may have occurred during transportation.
Take some time to read this manual carefully and understand all the content prior to assembly and
operation.
CAUTION
Always ensure that the tool is switched off and unplugged from the main supply
before assembly.
Changing the Blade
- Place the saw on the side of a flat surface.
- Rotate the saw blade (A) by hand while depressing the Spindle Lock Button (N) until the blade is
locked, Turn the blade clamp screw (I) by using the provided hex key in a clockwise direction.
- Remove the blade clamp screw (I) and the outer flange (H).
- Open the lower guard (K) by moving the lower guard lever (J), remove the blade.
- Clean the saw blade flanges, mount the new saw blade onto the spindle.
Fig. 1
A
B
C
D
E
F
GH
I
J
K
L
M
N
O
PQ
E
RS
11
- Make sure that the new saw blade is well centered at the inner ange when mounting the blade.
- Make sure the direction of rotation from the blade is the same as the rotation direction of the tool,
refer to the direction arrow at the tool and the direction arrow at the saw blade
- Reinstall the outer flange, washer and tighten the blade clamp screw.
- Make sure the saw blade can run freely by turning the blade by hand.
Parallel cut adjustment
Loosen the Parallel guide lock screw (F)
Slide parallel guide (G) through the slots in the base plate (L) to the desired width.
Tighten the Parallel guide lock screw (F) to secure it into position.
Ensure that the Parallel guide rests are parallel to the base plate to ensure a straight parallel cut.
Switching on and off
NOTE
Before engaging the on/off switch, check the saw blade to see if it is fitted properly
and runs smoothly, and the blade clamp screw is properly tightened.
- Connect the plug to the power supply.
- To start the tool, depress the lock-off button (C) and
then depress the switch trigger (B).
- To stop the tool release the switch trigger (B).
- Wait until the saw blade comes to a complete stop
before putting the machine down.
Fig. 3
F
L
G
F
B
C
Fig. 4
12
Depth Adjustment
- Before any adjustment, ensure the power plug is
removed from the socket.
- Loosen the depth adjustment screw using the depth
locking lever (O).
- Hold the base plate at against the body of the work
piece and lift the body of the saw until the blade is at
the correct depth.
- The adjusted cutting depth can be verified on the
depth scale (P).
- Tighten the depth locking lever.
Bevel Angle Adjustment
- Before any adjustment, ensure the power plug is
removed from the socket.
- Loosen the angle locking lever (E).
- Adjust the base plate (L) to the desired angle between
0ºand 45º.
- The adjusted cutting depth can be verified on the
angle scale (T).
- Re-tighten the angle locking lever (E).
Connecting the Dust Pipe
- Insert the dust pipe adapter (R) into the dust outlet (Q)
- Connect the other side of the dust pipe to a suitable vacuum cleaner or dust extractor to prevent
injury.
- Dust hose with 1-1/4" adapter allows attachment to 1-1/4" vacuum hose for dust removal (vacuum sold
separately).
NOTE
While using the dust pipe, regularly check that there is no dust or there are no wood chips blocking the
dust pipe.
L
P
OFig. 5
Fig. 6
E
L
T
Q
R
Fig. 7
13
OPERATION
General Cut
- Mark a cutting line on the workpiece (U).
- Rest the front part of the base plate(L) at on the workpiece surface with the blade not making any
contact with the workpiece.
- Switch on the tool and allow it to reach its full speed.
- Align the saw blade with the cutting line on the workpiece, gently push the saw forward.
- Never force the saw but maintain a light and continuous pressure when completing the cut.
- Switch off the tool only after the tool is completely away from the workpiece.
- If the cutting is interrupted, resume the cut by allowing the blade to reach full speed and then
reentering the cut slowly.
- When cutting across the grain, the fibers of the wood will have a tendency to lift and tear, move the
saw slowly to minimize this effect.
NOTE
For best cutting results, always ensure that the saw blade protrudes no more than 1/8" below the
bottom surface of the workpiece.
NOTE
There are two notches on the front edge of the shoe as an aid for alignment.When
making a 45⁰ bevel cut, just align the left notch marked with 45⁰ with the cutting line
on the workpiece. For a straight 90⁰ cut, align the right notch marked with 00 with
the cutting line on the workpiece. For precise cutting, always make a trial cut before
carrying out operation.
Fig. 8
U
U
L
L
14
Pocket Cut
- Disconnect the plug from the power supply before making any adjustments.
- Set the depth adjustment based on the thickness of the required cut.
- Raise the lower guard by using the lower guide lever.
- With the blade barely above the material to be cut, start the saw and allow the blade to attain full
speed.
- Using the front end of the shoe as a pivot point, lower the blade gradually onto the material which
is being cut.
- Release the lower guard when the blade starts cutting.
- When the shoe is resting flat on the surface being cut, proceed cutting in a forward direction to the
end of the cut.
- Allow the blade to come to a full stop before removing it from the cut.
- Never pull the saw backward since the blade will climb out of the cut, as a result, kickback may
occur.
Turn the saw around and finish the cut in a normal manner, sawing forward. Use a jigsaw or a hand
saw to finish the cut in the corners if it is necessary.
Cutting Large Sheets
- Large sheets or boards require support to prevent bending or sags. If you attempt to cut without
leveling and supporting the work piece properly, the blade will tend to bind or result in kickback.
- Support the panel or board close to the cut.
- Be sure to set the blade adjustment so that you can cut through the material without cutting into
the table or workbench.
- Suggestion: use two by fours (2"× 4") to support the board or panel to be cut.
- If the work piece is too large for the workbench, use the oor with two by fours (2"× 4") to support
the wood.
MAINTENANCE
WARNING
Preventive maintenance performed by unauthorized personnel may result in
misplacing of internal wires and components which could cause serious hazard.
CAUTION
Always be sure that the tool is switched off and unplugged before attempting
to perform inspection or maintenance. Regularly clean the tool’s air vents with
compressed dry air. Do not attempt to clean by inserting pointed objects through
openings.
15
CAUTION
Certain cleaning agents and solvents may damage plastic parts. Some of these
are: gasoline, carbon tetrachloride, chlorinated cleaning solvents, ammonia and
household detergents that contain ammonia.
WARNING
If any of the following events occur during normal operation, the power supply
should be shut off at once and tool thoroughly inspected by a qualified person and
repaired if necessary:
- The rotating parts get stuck or speed drops abnormally low.
- The tool shakes abnormally accompanied by some unusual noise.
- The motor housing gets abnormally hot.
- Heavy sparks occur around the motor area
ACCESSORIES
Hex key......................................................................................................... 1 pc
Parallel Guide................................................................................................ 1 pc
Instruction Manual......................................................................................... 1 pc
4-1/2” TCT Blade........................................................................................... 1 pc
Dust pipe…................................................................................................... 1 pc
PARTS LIST
Nr. Description Qty Nr. Description Qty
1PanHeadPhilips screw M4X14
(with washer)
5 43 Left housing 1
2Spindle lock cap 1 44 Screw for tension spring 1
3Spring for spindle lock 1 45 Spring washer 1
4 Gear box cover 1 46 Spindle lock cap 1
5 Circlip 1 47 Tension spring 1
6Cup head square neck bolts
M6X26
2 48 Trigger 1
7 Deep groove ball bearing 698 1 49 Spindle lock spring 2
8 Big spiral bevel gear 1 50 Socket terminal4.8X0.8 2
9 Steel ball Sφ3 3 51 Switch 1
10 Primary gear shaft 1 52 Gear for connecting rod 1
11 Deep groove ball bearing 607-2Z 4 53 Deep groove ball bearing 609.2Z 1
12 Circlip for hole D19 2 54 Circlip for hole D24 1
13 Washer(7.1Xφ13X0.5) 1 55 O ring 1
14 Intermediate shaft 1 56 Connecting sleeve 1
16
15 Big gear 1 57 Stator 1
16 Circlip for shaft D9 2 58 Deep groove ball bearing 608-2Z 1
17 Circlip for shaft D8 1 59 Rotor 1
18 Pinion 1 60 Socket terminal 2.8X0.8 2
19 Separation sleeve 1 61 Self-tapping screw ST2.9X10 2
20 Circlip for hole D20 2 62 Lower carbon brush holder 1
21 Deep groove ball bearing 699 1 63 Carbon brush 2
22 Pipe joint C 1 64 Deep groove ball bearing 606.2Z 1
23 Bellows 1 65 Bearing sleeve 1
24 Pipe joint D 1 66 Upper carbon brush holder 1
25 Self-tapping screw ST4.2X14 6 67 Self-tapping screw ST4.2X16 9
26 Gear box 1 68 Right housing 1
27 Dust cover 2 69 Right label 1
28 Spindle(120V) 1 70 Power cord sleeve 1
29 Fixed guard 1 71 Hex key 5 1
30 Pan Head Philips screw(with
washer)
2 72 Power cord 1
31 Cross-shaped screw M4X12 1 73 Circlip for shaft D10 2
32 Rubber block 1 74 Depth lever 2
33 Screw for rubber block M5 1 75 Locking lever 2
34 Moving guard 1 76 Washer 1
35 Baffle ring 1 77 Hexagon socket head cap screws
M6X12
1
36 Inner flange 1 78 Edge guide locking spring 1
37 TCT blade 1 79 Base plate 1
38 Blade fixed screw 1 80 Cylindrical spring pin D6X35 1
39 Outer flange(120V) 1 81 Parallel guide 1
40 Self-tapping screw ST4.2X12 1 82 Power cord clamp 1
41 Moving guard lever 1 83 Wires connecting blocks 1
42 Left label 1
18
WARRANTY
21
For questions / comments, technical assistance or repair parts –
Please Call Toll Free at: 1-866-915-8626 (M-F 9am – 5pm)
SAVE YOUR RECEIPTS. THIS WARRANTYY IS VOID WITHOUTT THEM.
Rev 1.3 12/09/2015
Distributed by: Menard, Inc., Eau Claire, WI 54703
PERFORMAX
TM
4-1/2" COMPACT CIRCULAR SAW WARRANTY
30-DAY MONEY BACK GUARANTEE:
:
This PERFORMAXTM brand power tool carries our 30-Day Money Back
Guarantee. If you are not completely satisfied with your PERFORMAXTM brand
power tool for any reason within thirty (30) days from the date of purchase, return
the tool with your original receipt to any MENARDS®retail store, and we will
provide you a refund – no questions asked.
2-YEAR LIMITED WARRANTY:
This PERFORMAX brand power tool carries a 2-Year Limited Warranty to the
original purchaser. If, during normal use, this PERFORMAX power tool breaks
or fails due to a defect in material or workmanship within two (2) years from the
date of original purchase, simply bring this tool with the original sales receipt
back to your nearest MENARDS retail store. At its discretion, PERFORMAX
agrees to have the tool or any defective part(s) repaired or replaced with the
same or similar PERFORMAX product or part free of charge, within the stated
warranty period, when returned by the original purchaser with original sales
receipt. Notwithstanding the foregoing, this limited warranty does not cover any
damage that has resulted from abuse or misuse of the Merchandise. This
warranty: (1) excludes expendable parts including but not limited to driver blades,
O rings, blades, brushes, belts, bits, light bulbs, and/or batteries; (2) shall be void
if this tool is used for commercial and/or rental purposes; and (3) does not cover
any losses, injuries to persons/property or costs. This warranty does give you
specific legal rights and you may have other rights, which vary from state to
state. Be careful, tools are dangerous if improperly used or maintained. Seller’s
employees are not qualified to advise you on the use of this Merchandise. Any
oral representation(s) made will not be binding on seller or its employees. The
rights under this limited warranty are to the original purchaser of the Merchandise
and may not be transferred to any subsequent owner. This limited warranty is in
lieu of all warranties, expressed or implied including warranties or merchantability
and fitness for a particular purpose. Seller shall not be liable for any special,
incidental, or consequential damages. The sole exclusive remedy against the
seller will be for the replacement of any defects as provided herein, as long as
the seller is willing or able to replace this product or is willing to refund the
purchase price as provided above. For insurance purposes, seller is not allowed
to demonstrate any of these power tools for you.
TM
TM
® TM
TM
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Performax 241-0944 Owner's manual
- Category
- Power tools
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI