kontron KBox A-150-APL User guide

Type
User guide
USER GUIDE
www.kontron.com // 1
KBox A-150-APL
Doc. User Guide, Rev. 1.6
Doc. ID: 1062-3589
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 2
This page has been intentionally left blank
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 3
KBOX A
-150-APL - USER GUIDE
Disclaimer
Kontron would like to point out that the information contained in this user guide may be subject to alteration,
particularly as a result of the constant upgrading of Kontron products. This document does not entail any guarantee on
the part of Kontron with respect to technical processes described in the user guide or any product characteristics set
out in the user guide. Kontron assumes no responsibility or liability for the use of the described product(s), conveys no
license or title under any patent, copyright or mask work rights to these products and makes no representations or
warranties that these products are free from patent, copyright or mask work right infringement unless otherwise
specified. Applications that are described in this user guide are for illustration purposes only. Kontron makes no
representation or warranty that such application will be suitable for the specified use without further testing or
modification. Kontron expressly informs the user that this user guide only contains a general description of processes
and instructions which may not be applicable in every individual case. In cases of doubt, please contact Kontron.
This user guide is protected by copyright. All rights are reserved by Kontron. No part of this document may be
reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), without the
express written permission of Kontron. Kontron points out that the information contained in this user guide is
constantly being updated in line with the technical alterations and improvements made by Kontron to the products and
thus this user guide only reflects the technical status of the products by Kontron at the time of publishing.
Brand and product names are trademarks or registered trademarks of their respective owners.
©2018 by Kontron Europe GmbH
Kontron Europe GmbH
Gutenbergstraße 2
85737 Ismaning
Germany
www.kontron.com
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 4
Intended Use
This DIN rail industrial embedded computer platform, sold by Kontron, is part of Kontron’s A-Series intended for
control cabinet applications, offering high performance at low power dissipation. The KBox A-150 product family can
operate in a temperature range from 0°C to plus 40°C, and a humidity of 10 to 90 percent does not affect the function
of the product. The products fanless design ensures a significantly prolonged lifespan and high system availability.
This product offers flexible DIN Rail mounting positions within a control cabinet even when space is limited. Users
must comply with all product specifications stated in the product documentation and this user guide. If it is intended,
to incorporated the product into any total systems or applications, carry out sufficient, compatibility and functions
tests prior to any use or resale.
THIS PRODUCT IS NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE OR RESALE FOR THE
OPERATION OF APPLICATION IN A HAZARDOUS ENVIRONMENT, OR REQUIRING FAIL-SAFE PERFORMANCE,
OR IN WHICH THE FAILURE OF PRODUCTS COULD LEAD DIRECTLY TO DEATH, PERSONAL INJURY, OR SEVERE
PHYSICAL OR ENVIRONMENTAL DAMAGE (COLLECTIVELY "HIGH RISK APPLICATIONS").
You understand and agree that your use of Kontron product as a component in High Risk Applications is entirely at
your own risk. To minimize the risks associated with your systems and applications, you must provide adequate
design and operating safeguards. You are responsible to ensure that your systems (and any Kontron hardware or
software products incorporated in your systems) meet all applicable requirements. Unless otherwise stated in the
product documentation, the Kontron product is not provided with error-tolerance capabilities and therefore cannot
be deemed as being engineered, manufactured or setup to be compliant for implementation or for resale as a
component in High Risk Applications. All application and safety related information in this document (including
application descriptions, suggested safety measures, suggested Kontron products, and other materials) is provided
for reference only.
You find the most recent version of the “General Safety Instructions“ online in the download
area of this product.
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 5
Revision History
Revision Brief Description of Changes Date of Issue Author/
Editor
1.0 Initial version 2018-Oct-02 CW
1.1 Update standards, BIOS, block diagram, scope of delivery, accessories,
type label, battery info, OS type, internal component pin assignments,
and standards certification and directives information. Added heatsink
dimensions, keep out area data and internal component diagram.
2020-Jan-07 CW
1.2 Added UEFI BIOS only information in Chapter 12. 2020-Feb-05 CW
1.3 Updated general safety instructions and added caution in Special
Handling and Unpacking Instruction. Added PSU spec. data and LPS
caution. Added mating power connector/terminal wiring
spec/restrictions.
2020-Sept-09 CW
1.4 Updates Figures 4, 21 and 23 with DSUB serial connectors orientation
changed. Renamed Chapter 10.5 Compliance. Updated boiler text,
company name and address, and General Safety Instructions. Changed
Battery warning in Ch. 1.2 and Ch.14.3.1.
2022-Jan-05 CW
1.5 Added Comment “highest Baudrate for RS232 is 115200 kbit/s in
Chapters 4.1.8 and 11.1.6.
2022-Sept-28 CW
1.6 Replaced Ubuntu with Linux and added new logo 2023-Sept-06 CW
Terms and Conditions
Kontron warrants products in accordance with defined regional warranty periods. For more information about
warranty compliance and conformity, and the warranty period in your region, visit http://www.kontron.com/terms-
and-conditions.
Kontron sells products worldwide and declares regional General Terms & Conditions of Sale, and Purchase Order
Terms & Conditions. Visit http://www.kontron.com/terms-and-conditions.
For contact information, refer to the corporate offices contact information on the last page of this user guide or visit
our website CONTACT US.
Customer Support
Find Kontron contacts by visiting: https://www.kontron.com/en/support.
Customer Service
As a trusted technology innovator and global solutions provider, Kontron extends its embedded market strengths into
a services portfolio allowing companies to break the barriers of traditional product lifecycles. Proven product
expertise coupled with collaborative and highly-experienced support enables Kontron to provide exceptional peace of
mind to build and maintain successful products.
For more details on Kontron’s service offerings such as: enhanced repair services, extended warranty, Kontron
training academy, and more visit https://www.kontron.com/en/service
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 6
Customer Comments
If you have any difficulties using this user guide, discover an error, or just want to provide some feedback, contact
Kontron Support. Detail any errors you find. We will correct the errors or problems as soon as possible and post the
revised user guide on our website.
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 7
Symbols
The following symbols may be used in this user guide
DANGER indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
NOTICE indicates a property damage message.
CAUTION indicates a hazardous situation which, if not avoided,
may result in minor or moderate injury.
Electric Shock!
This symbol and title warn of hazards due to electrical shocks (> 60
V) when touching
products or parts of products. Failure to observe the precautions indicated and/or prescribed
by the law may endanger your life/health and/or result in damage to your material.
ESD Sensitive Device!
This symbol and title inform that the electronic boards and their components are sensitive to
static electricity. Care must therefore be taken during all handling operations and inspections
of this product in order to ensure product integrity at all times.
HOT Surface!
Do NOT touch! Allow to cool before servicing.
Laser!
This symbol informs of the risk of exposure to laser beam and light emitting devices (LEDs)
from an electrical device. Eye protection per manufacturer notice shall review before
servicing.
This symbol indicates general information about the product and the user guide.
This symbol also indicates detail information about the specific product configuration.
This symbol precedes helpful hints and tips for daily use.
KBox A-150-APLUser Guide, Rev. 1.6
www.kontron.com // 8
For Your Safety
Your new Kontron product was developed and tested carefully to provide all features necessary to ensure its
compliance with electrical safety requirements. It was also designed for a long fault-free life. However, the life
expectancy of your product can be drastically reduced by improper treatment during unpacking and installation.
Therefore, in the interest of your own safety and of the correct operation of your new Kontron product, you are
requested to conform with the following guidelines.
High Voltage Safety Instructions
As a precaution and in case of danger, the power connector must be easily accessible. The power connector is the
product’s main disconnect device.
Warning
All operations on this product must be carried out by sufficiently skilled personnel only.
Electric Shock!
Before installing a non hot-swappable Kontron product into a system always ensure that
your main power is switched off. This also applies to the installation of piggybacks. Serious
electrical shock hazards can exist during all installation, repair, and maintenance operations
on this product. Therefore, always unplug the power cable and any other cables which
provide external voltages before performing any work on this product.
Earth ground connection to vehicle’s chassis or a central grounding point shall remain
connected. The earth ground cable shall be the last cable to be disconnected or the first
cable to be connected when performing installation or removal procedures on this product.
Special Handling and Unpacking Instruction
ESD Sensitive Device!
Electronic boards and their components are sensitive to static electricity. Therefore, care
must be taken during all handling operations and inspections of this product, in order to
ensure product integrity at all times.
Handling and operation of the product is permitted only for trained personnel within a work
place that is access controlled. Follow the “General Safety Instructions” supplied with the
system.
Do not handle this product out of its protective enclosure while it is not used for operational purposes unless it is
otherwise protected.
Whenever possible, unpack or pack this product only at EOS/ESD safe work stations. Where a safe work station is not
guaranteed, it is important for the user to be electrically discharged before touching the product with his/her hands
or tools. This is most easily done by touching a metal part of your system housing.
It is particularly important to observe standard anti-static precautions when changing piggybacks, ROM devices,
jumper settings etc. If the product contains batteries for RTC or memory backup, ensure that the product is not placed
on conductive surfaces, including anti-static plastics or sponges. They can cause short circuits and damage the
batteries or conductive circuits on the product.
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 9
Lithium Battery Precautions
If your product is equipped with a lithium battery, take the following precautions when replacing the battery.
Danger of explosion if the battery is replaced incorrectly.
Replace only with same or equivalent battery type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
General Instructions on Usage
In order to maintain Kontron’s product warranty, this product must not be altered or modified in any way. Changes or
modifications to the product, that are not explicitly approved by Kontron and described in this user guide or received
from Kontron Support as a special handling instruction, will void your warranty.
This product should only be installed in or connected to systems that fulfill all necessary technical and specific
environmental requirements. This also applies to the operational temperature range of the specific board version
that must not be exceeded. If batteries are present, their temperature restrictions must be taken into account.
In performing all necessary installation and application operations, only follow the instructions supplied by the
present user guide.
Keep all the original packaging material for future storage or warranty shipments. If it is necessary to store or ship
the product, then re-pack it in the same manner as it was delivered.
Special care is necessary when handling or unpacking the product. See Special Handling and Unpacking Instruction.
Quality and Environmental Management
Kontron aims to deliver reliable high-end products designed and built for quality, and aims to complying with
environmental laws, regulations, and other environmentally oriented requirements. For more information regarding
Kontron’s quality and environmental responsibilities, visit http://www.kontron.com/about-kontron/corporate-
responsibility/quality-management.
Disposal and Recycling
Kontron’s products are manufactured to satisfy environmental protection requirements where possible. Many of the
components used are capable of being recycled. Final disposal of this product after its service life must be
accomplished in accordance with applicable country, state, or local laws or regulations.
WEEE Compliance
The Waste Electrical and Electronic Equipment (WEEE) Directive aims to:
Reduce waste arising from electrical and electronic equipment (EEE)
Make producers of EEE responsible for the environmental impact of their products, especially when the product
become waste
Encourage separate collection and subsequent treatment, reuse, recovery, recycling and sound environmental
disposal of EEE
Improve the environmental performance of all those involved during the lifecycle of EEE
Environmental protection is a high priority with Kontron.
Kontron follows the WEEE directive
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 10
Table of Contents
Symbols ................................................................................................................................................................................................................. 7
For Your Safety .................................................................................................................................................................................................. 8
High Voltage Safety Instructions ................................................................................................................................................................. 8
Special Handling and Unpacking Instruction ........................................................................................................................................... 8
Lithium Battery Precautions ........................................................................................................................................................................... 9
General Instructions on Usage ...................................................................................................................................................................... 9
Quality and Environmental Management ................................................................................................................................................. 9
Disposal and Recycling ..................................................................................................................................................................................... 9
WEEE Compliance............................................................................................................................................................................................... 9
Table of Contents............................................................................................................................................................................................. 10
List of Tables ..................................................................................................................................................................................................... 12
List of Figures .................................................................................................................................................................................................... 12
1/ General Safety Instructions ........................................................................................................................................................... 14
Electrostatic Discharge (ESD) ................................................................................................................................................................ 15
1.1.1. Grounding Methods ................................................................................................................................................................................ 15
Instructions for Lithium Battery ........................................................................................................................................................... 16
2/ Electromagnetic Compatibility (Class B Device) .................................................................................................................... 17
Electromagnetic Compatibility (EU) .................................................................................................................................................... 17
FCC Statement (USA) ............................................................................................................................................................................... 17
EMC-Compliance (Canada) ................................................................................................................................................................... 17
3/ Shipment and Unpacking ................................................................................................................................................................ 18
Packaging ..................................................................................................................................................................................................... 18
Unpacking.................................................................................................................................................................................................... 18
Scope of Delivery ...................................................................................................................................................................................... 18
Accessories ................................................................................................................................................................................................ 18
Type Label and Product Identification ............................................................................................................................................... 19
Kontron Parts (option) ............................................................................................................................................................................ 19
4/ System Overview .............................................................................................................................................................................. 20
Front Panel Views ..................................................................................................................................................................................... 21
4.1.1. DC Input Power Connector ................................................................................................................................................................. 22
4.1.2. Protective Earth Stud Bolt ................................................................................................................................................................. 22
4.1.3. HDMI .......................................................................................................................................................................................................... 22
4.1.4. Display Port (DP) .................................................................................................................................................................................. 22
4.1.5. Ethernet (LAN1, LAN2) ......................................................................................................................................................................... 22
4.1.6. USB 3.0 Ports ......................................................................................................................................................................................... 22
4.1.7. Power-On Switch .................................................................................................................................................................................. 22
4.1.8. Serial Ports (X1, X2).............................................................................................................................................................................. 22
4.1.9. Breakouts (X3, X4) ............................................................................................................................................................................... 23
Rear View ................................................................................................................................................................................................... 23
Top View and Bottom View .................................................................................................................................................................. 23
Side Views .................................................................................................................................................................................................. 24
Internal Components ............................................................................................................................................................................. 25
SBC On-board Components ................................................................................................................................................................. 26
5/ System Expansion ............................................................................................................................................................................ 27
External Storage Expansion ................................................................................................................................................................. 27
Internal Expansion .................................................................................................................................................................................. 28
5.2.1. M.2 Module ............................................................................................................................................................................................. 28
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 11
5.2.2. mPCIe Expansion Card ........................................................................................................................................................................ 28
6/ Accessing Components ................................................................................................................................................................... 29
Accessing the 2.5” HDD/SSD Drive Bay ............................................................................................................................................. 29
Opening the System ............................................................................................................................................................................... 30
6.2.1. Installing and Removing M.2 SSD Cards ....................................................................................................................................... 33
6.2.2. Installing and Removing mPCIe Expansion Cards ..................................................................................................................... 34
7/ Thermal Considerations ................................................................................................................................................................. 35
Heatsink Plate ............................................................................................................................................................................................ 35
Heatsink (Option) ..................................................................................................................................................................................... 35
8/ Installation Instructions ................................................................................................................................................................. 36
DIN Rail Mounting .................................................................................................................................................................................... 36
Control Cabinet Mounting .................................................................................................................................................................... 37
Wiring the Mating Power Connector/Terminal ............................................................................................................................ 38
9/ Switching On ....................................................................................................................................................................................... 40
Connecting to a DC Power Supply ...................................................................................................................................................... 40
Switch On .................................................................................................................................................................................................... 41
Switch Off .................................................................................................................................................................................................... 41
Operating System (OS) and Drivers ................................................................................................................................................... 41
10/ Technical Data ................................................................................................................................................................................... 42
Block Diagram.......................................................................................................................................................................................... 42
Technical Specification ........................................................................................................................................................................ 43
Mechanical Specification .................................................................................................................................................................... 44
10.3.1. Mechanical Diagrams ........................................................................................................................................................................ 44
Environmental Specification ............................................................................................................................................................. 48
Compliance .............................................................................................................................................................................................. 49
Power Supply Specification ................................................................................................................................................................ 51
10.6.1. Power Supply Protection Requirements ...................................................................................................................................... 51
10.6.2. Power Consumption .......................................................................................................................................................................... 52
10.6.3. Protective Earth Stud Bolt ............................................................................................................................................................... 52
11/ Connector Pin Assignments .......................................................................................................................................................... 53
Front Panel Connector Pin Assignments ......................................................................................................................................... 53
11.1.1. Input Power Connector (- +) ............................................................................................................................................................ 53
11.1.2. HDMI Connector (HDMI) .................................................................................................................................................................... 53
11.1.3. Display Port Connector (DP) ............................................................................................................................................................ 53
11.1.4. GbE RJ45 Connectors (LAN1, LAN2) ............................................................................................................................................... 54
11.1.5. USB 3.0 Port Connectors ................................................................................................................................................................... 54
11.1.6. Serial Port Connectors (X1, X2)........................................................................................................................................................ 54
SBC On-board Connector and Jumper Pin Assignments ........................................................................................................... 55
11.2.1. Battery Power Input Connector ...................................................................................................................................................... 55
11.2.2. 12 VDC Out Power Connector .......................................................................................................................................................... 55
11.2.3. HDD Power Output Connector ........................................................................................................................................................ 55
11.2.4. Serial-ATA Port 0 (SATA1) Connector........................................................................................................................................... 55
11.2.5. Serial Port 1 and Serial Port 2 Connector .................................................................................................................................... 56
11.2.6. USB 2.0 Port Pin Header .................................................................................................................................................................... 56
11.2.7. Audio Input/Output Pin Header ...................................................................................................................................................... 56
11.2.8. Left Channel 3W Audio AMP Output Connector ........................................................................................................................ 57
11.2.9. Right Channel 3W Audio Amplification Output Connector ..................................................................................................... 57
11.2.10. Power-on Switch Pin Header ......................................................................................................................................................... 57
11.2.11. USB Power Selection Jumper (JP9) ............................................................................................................................................... 57
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 12
11.2.12. Micro-SD Card Cage ........................................................................................................................................................................... 57
12/ BIOS ........................................................................................................................................................................................................ 58
Starting the uEFI BIOS ........................................................................................................................................................................... 58
Setup Menus ............................................................................................................................................................................................ 59
12.2.1. Main Setup Menu ................................................................................................................................................................................ 59
12.2.2. Advanced Setup Menu ...................................................................................................................................................................... 60
12.2.3. Power Setup Menu ............................................................................................................................................................................. 64
12.2.4. Boot Setup Menu ................................................................................................................................................................................ 65
12.2.5. Security Setup Menu ......................................................................................................................................................................... 66
12.2.6. Save and Exit Set up Menu .............................................................................................................................................................. 68
13/ Technical Support ............................................................................................................................................................................. 69
Returning Defective Merchandise .................................................................................................................................................... 69
14/ Storage, Transportation and Maintenance ............................................................................................................................. 70
Storage ....................................................................................................................................................................................................... 70
Transportation ....................................................................................................................................................................................... 70
Maintenance ............................................................................................................................................................................................ 70
14.3.1. Cleaning .................................................................................................................................................................................................. 70
14.3.2. Replacing the Lithium Battery ....................................................................................................................................................... 70
15/ Warranty .............................................................................................................................................................................................. 72
Limitation/Exemption from Warranty Obligation ....................................................................................................................... 72
Appendix: List of Acronyms ........................................................................................................................................................................ 73
About Kontron .................................................................................................................................................................................................. 74
List of Tables
Table 1: Scope of Delivery .............................................................................................................................................................................. 18
Table 2: Accessories ........................................................................................................................................................................................ 18
Table 3: Product Identification ..................................................................................................................................................................... 19
Table 4: External Storage Devices ............................................................................................................................................................. 27
Table 5: M.2 Module memory Expansion ................................................................................................................................................ 28
Table 6: Expansion Card Option .................................................................................................................................................................. 28
Table 7: Technical Specification ................................................................................................................................................................. 43
Table 8: Mechanical Specification ............................................................................................................................................................. 44
Table 9: Environmental Specification ....................................................................................................................................................... 48
Table 10: Compliance of KBox A-150-APL without Wi-Fi ................................................................................................................... 49
Table 11: Certifications of KBox A-150-APL with Wi-Fi........................................................................................................................ 49
Table 12: KBox A-150-APL Electrical Specification ................................................................................................................................ 51
Table 13: Power Consumption ..................................................................................................................................................................... 52
Table 14: Navigation Hot Keys Available in the Legend Bar .............................................................................................................. 58
Table 15: Advanced Menu ............................................................................................................................................................................. 60
Table 16: Power Configuration Setup Menu ........................................................................................................................................... 64
Table 17: Boot Setup Menu Sub-screens and Functions .................................................................................................................... 65
Table 18: Security Setup Menu Sub-screens and Functions ............................................................................................................. 66
Table 19: Save and Exit Setup Menu Sub-screens and Functions ................................................................................................... 68
Table 20: List of Acronyms ........................................................................................................................................................................... 73
List of Figures
Figure 1: Type Label Example ....................................................................................................................................................................... 19
Figure 2: KBox A-150-APL Drive Bay Variant .......................................................................................................................................... 20
Figure 3: Front Panel (with external 2.5”HDD/SSD drive bay) .......................................................................................................... 21
Figure 4: Front Panel (no external drive bay) ......................................................................................................................................... 21
Figure 5: Rear View ......................................................................................................................................................................................... 23
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 13
Figure 6: Top and Bottom Views ................................................................................................................................................................ 23
Figure 7: Left Side View and Right Side View (with external 2.5” HDD/SSD drive bay) ............................................................ 24
Figure 8: Left Side View and Right Side View (with no external drive bay) ................................................................................. 24
Figure 9: Internal Components ................................................................................................................................................................... 25
Figure 10: SBC On-board Connectors ........................................................................................................................................................ 26
Figure 11: 2.5” HDD/SSD Drive Bay ............................................................................................................................................................. 29
Figure 12: SBC Fastening Screws ................................................................................................................................................................. 31
Figure 13: Front Panel Fastening Screws.................................................................................................................................................. 31
Figure 14: Removing the Front panel- SBC Assembly ......................................................................................................................... 32
Figure 15: M.2 Module on the SBC .............................................................................................................................................................. 33
Figure 16: mPCIe Expansion Card on the SBC ......................................................................................................................................... 34
Figure 17: Heatsink and Heatsink with DIN Rail Clamp ........................................................................................................................ 35
Figure 18: DIN Rail Mounting Clamp Upper Position ............................................................................................................................ 36
Figure 19: DIN Rail Mounting Clamp Screw Dimensions (mm) ......................................................................................................... 36
Figure 20: Keep Out Area for Mounting for KBox A-150-APL (with external 2.5” HDD/SSD drive bay) .............................. 37
Figure 21: Keep Out Area for Mounting for KBox A-150-APL (with no drive bay) ...................................................................... 37
Figure 22: Keep Out Area for Mounting for KBox A-150-APL (with heatsink & external 2.5” HDD/SSD drive bay) ........ 37
Figure 23: Keep Out Area for Mounting for KBox A-150-APL (with heatsink & no drive bay) ................................................ 37
Figure 24: Keep Out Area for installed dual Wi-Fi Antenna (with external 2.5” HDD/SSD drive bay) ................................ 38
Figure 25: Input Power Connector and Mating Power Connector/Terminal ............................................................................... 38
Figure 26: Block Diagram .............................................................................................................................................................................. 42
Figure 27: Front Panel Dimensions with External 2.5” Drive Bay (mm) ........................................................................................ 44
Figure 28: Rear Side Dimensions with External 2.5” Drive Bay (mm) ............................................................................................ 44
Figure 29: Top Side Dimensions with External Drive Bay (mm) ...................................................................................................... 45
Figure 30: Side View Dimensions with External 2.5” Drive Bay (mm) ............................................................................................ 45
Figure 31: Front Panel Dimensions without Drive Bay (mm) ............................................................................................................ 45
Figure 32: Rear Side Dimensions without Drive Bay (mm) ................................................................................................................ 46
Figure 33: Top Side Dimensions with External Drive Bay (mm) ...................................................................................................... 46
Figure 34: Side View Dimensions without Drive Bay (mm) ............................................................................................................... 46
Figure 35: Mechanical Diagram Heatsink (mm) .................................................................................................................................... 47
Figure 36: Main Setup Menu Example ...................................................................................................................................................... 59
Figure 37: Advanced Setup Menu Example ............................................................................................................................................. 60
Figure 38: Power Configuration Setup Menu Example ....................................................................................................................... 64
Figure 39: Boot Setup Menu Example ....................................................................................................................................................... 65
Figure 40: Security Setup Menu Example ............................................................................................................................................... 66
Figure 41: Save and Exit Set up Menu Example ..................................................................................................................................... 68
Figure 42: Lithium Battery Location ........................................................................................................................................................... 71
Figure 43: Lithium Battery Power Input Connector .............................................................................................................................. 71
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 14
1/ General Safety Instructions
Please read this passage carefully and take careful note of the instructions, which have been compiled for your safety
and to ensure to apply in accordance with intended regulations. If the following general safety instructions are not
observed, it could lead to injuries to the operator and/or damage of the product; in cases of non-observance of the
instructions Kontron Europe is exempt from accident liability, this also applies during the warranty period.
The product has been built and tested according to the basic safety requirements for low voltage (LVD) applications
and has left the manufacturer in safety-related, flawless condition. To maintain this condition and to also ensure safe
operation, the operator must not only observe the correct operating conditions for the product but also the following
general safety instructions:
The product must be used as specified in the product documentation, in which the instructions for safety for the
product and for the operator are described. These contain guidelines for setting up, installation and assembly,
maintenance, transport or storage.
The on-site electrical installation must meet the requirements of the country's specific local regulations.
If a power cable comes with the product, only this cable should be used. Do not use an extension cable to connect
the product.
To guarantee that sufficient air circulation is available to cool the product, please ensure that the ventilation
openings are not covered or blocked. If a filter mat is provided, this should be cleaned regularly. Do not place the
product close to heat sources or damp places. Make sure the product is well ventilated.
Only connect the product to an external power supply providing the voltage type (AC or DC) and the input power
(max. current) specified on the Kontron Product Label and meeting the requirements of the Limited Power Source
(LPS) and Power Source (PS2) of UL/IEC 62368-1.
Only products or parts that meet the requirements for Power Source (PS1) of UL/IEC 62368-1 may be connected
to the product’s available interfaces (I/O).
Before opening the product, make sure that the product is disconnected from the mains.
Switching off the product by its power button does not disconnect it from the mains. Complete disconnection is
only possible if the power cable is removed from the wall plug or from the product. Ensure that there is free and
easy access to enable disconnection.
The product may only be opened for the insertion or removal of add-on cards (depending on the configuration of
the product). This may only be carried out by qualified operators.
If extensions are being carried out, the following must be observed:
all effective legal regulations and all technical data are adhered to
the power consumption of any add-on card does not exceed the specified limitations
the current consumption of the product does not exceed the value stated on the product label.
Only original accessories that have been approved by Kontron Europe can be used.
Please note: safe operation is no longer possible when any of the following applies:
the product has visible damages or
the product is no longer functioning
In this case the product must be switched off and it must be ensured that the product can no longer be
operated.
Handling and operation of the product is permitted only for trained personnel within a work place that is access
controlled.
CAUTION: Risk of explosion if the battery is replaced incorrectly (short-circuited, reverse-poled, wrong battery
type). Dispose of used batteries according to the manufacturer’s instructions.
This product is not suitable for use in locations where children are likely to be present.
Additional Safety Instructions for DC Power Supply Circuits
To guarantee safe operation, please observe that:
the external DC power supply must meet the criteria for LPS and PS2 (UL/IEC 62368-1)
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 15
no cables or parts without insulation in electrical circuits with dangerous voltage or power should be
touched directly or indirectly
a reliable protective earthing connection is provided
a suitable, easily accessible disconnecting device is used in the application (e.g. overcurrent protective
device), if the product itself is not disconnectable
a disconnect device, if provided in or as part of the product, shall disconnect both poles simultaneously
interconnecting power circuits of different products cause no electrical hazards
A sufficient dimensioning of the power cable wires must be selected according to the maximum electrical
specifications on the product label as stipulated by EN62368-1 or VDE0100 or EN60204 or UL61010-1
regulations.
Electrostatic Discharge (ESD)
A sudden discharge of electrostatic electricity can destroy static-sensitive devices or micro-
circuitry.
Therefore, proper packaging and grounding techniques are necessary precautions to prevent damage. Always take
the following precautions:
1. Transport boards in ESD-safe containers such as boxes or bags.
2. Keep electrostatic sensitive parts in their containers until they arrive at the ESD-safe workplace.
3. Always be properly grounded when touching a sensitive board, component, or assembly.
4. Store electrostatic-sensitive boards in protective packaging or on antistatic mats.
1.1.1. Grounding Methods
By adhering to the guidelines below, electrostatic damage to the product can be avoided:
1. Cover workstations with approved antistatic material. Always wear a wrist strap connected to workplace. Always
use properly grounded tools and equipment.
2. Use antistatic mats, heel straps, or air ionizers for more protection.
3. Always handle electrostatically sensitive components by their edge or by their casing.
4. Avoid contact with pins, leads, or circuitry.
5. Switch off power and input signals before inserting and removing connectors or connecting test equipment.
6. Keep work area free of non-conductive materials such as ordinary plastic assembly aids and Styrofoam.
7. Use only field service tools that are conductive, such as cutters, screwdrivers, and vacuum cleaners.
8. Always place drives and boards PCB-assembly-side down on the foam.
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 16
Instructions for Lithium Battery
The KBox A-150-APL is equipped with a Kontron specific battery assembly and is not designed to operate without a
battery. If the battery is empty or disconnected, the BIOS settings will be set to the factory defaults. To replace the
battery, observe the instructions described in Chapter 14.3.1: Replacing the Lithium Battery.
Caution: Risk of Explosion if Battery is replaced by an Incorrect Type. Dispose of Used
Batteries According to the Instructions.
ATTENTION: Risque d’explosion si la batterie est remplacée par un type incorrect. Mettre au
rebus les batteries usagées selon les instructions.
After removing the lithium battery, dispose of the lithium battery according to the regulations within your region.
Do not dispose of lithium batteries in general trash collection. Dispose of the battery
according to the local regulations dealing with the disposal of these special materials, (e.g.
to collecting points for battery disposal).
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 17
2/ Electromagnetic Compatibility (Class B Device)
Electromagnetic Compatibility (EU)
This product complies with the European Council Directive on the approximation of the laws of the member states
relating to Electromagnetic Compatibility (EMC) directive 2014/30/EU ensuring that electrical and electronic
equipment does not generate, or is not affected by, electrical disturbance.
The EMC directive 2014/30/EU limits electromagnetic emissions from products to ensure that, when used as
intended, the product does not disturb radio and telecommunication, or other equipment. The directive also governs
the immunity of the product to interference and seeks to ensure that the product is not disturbed by radio emissions,
when used as intended.
FCC Statement (USA)
This product has been tested and found to comply with Part 15 of the Federal Communications Commission (FCC)
Rules for Class B products. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This product generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this product does cause harmful interference to radio or television reception, that can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the product and receiver.
Connect the product into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Kontron is not responsible for any radio television interference caused by unauthorized modifications of this product
or the substitution or attachment of connecting cables and devices other than those specified by Kontron. The
correction of interference caused by such unauthorized modification, substitution or attachment will be the
responsibility of the user.
The use of shielded I/O cables is required when connecting this product to an optional peripheral or host devices.
Failure to do so may violate FCC and ICES rules.
EMC-Compliance (Canada)
The method of compliance is self-declaration:
(English): This Class B product complies with the Canadian ICES-003.
(French) : Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 18
3/ Shipment and Unpacking
Packaging
All parts are delivered together in a product specific cardboard package designed to provide adequate protection to
absorb shock. Kontron recommends keeping the packaging to store or transport the product.
Unpacking
To unpack the product, perform the following:
1. Remove packaging.
2. Do not discard the original packaging. Keep the original packaging for future transportation or storage.
3. Check the delivery for completeness by comparing the delivery with the original order.
4. Keep the associated paperwork. It contains important information for handling the product.
5. Check the contents for visible shipping damage.
6. If you notice any shipping damage or inconsistencies between the contents and the original order, contact
Kontron for help and information.
Scope of Delivery
Check that your delivery is complete, and contains the items listed below. If you discover damaged or missing items,
contact your dealer.
Table 1: Scope of Delivery
Delivered Item Part Description
KBox A-150-APL Corresponding to the ordered product configuration
Phoenix Power Connector 3-pin mating power connector/terminal (PSC 1,5/ 3-F) inserted on DC Input Power
connector
DIN Rail Clamp DIN rail clamp installed on the rear side using 2x M4x6 screws
HDD Protective Film Adhesive protective film attaches to the 2.5” HDD/SDD to protect the HDD/SSD against
antistatic electrification when touched. ( External drive bay variant only)
General Safety
Instructions
General safety instruction when operating or handling IT equipment
Accessories
Table 2: Accessories
Part Number Part Part Description
EE04-100001-01 Power connector (3-pin) Phoenix mating power connector/terminal (PSC 1,5/ 3-F)
in DSUB 9 housing
ER40-100001-01 Power Supply 24 V External AC/DC PSU with 50 W, 24 VDC at 40°C
840-0059 Power cable EU Power cable AC mains to external adapter, Europe, UK
and USA
840-0115 Power cable UK
840-0405 / 0-0064-4317 Power cable US
PM00-100057-01 HDD/SSD extension frame Adjusts drives installation height from 7 mm to 9 mm
EN05-100003-01 Heatsink kit Heatsink with four screws (M4x8 )
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 19
Type Label and Product Identification
The KBox A-150-APL is part of Kontron’s DIN rail embedded Box PC. Kontron’s A-Series is intended for control cabinet
applications.
Table 3: Product Identification
System
Type
Product
Designation Model Description
KBox A KBox A-150 KBox A-150-APL Corresponds to system configurations with the
ECX-APL0, 3.5” ECX Single Board Computer with
Intel® Pentium® Quad Core™ N4200 processor
The type label contains specific product identification information and KBox A-150-APL technical information.
Figure 1: Type Label Example
1
Model
2 Material Part Number(MPN) with
3 Serial Number (S/N) with barcode
4
For internal use
5 Certification information
6 Technical information
Kontron Parts (option)
The APPROTECT security solution is based on WIBU-Systems CodeMeter® in tandem with a specifically developed
software framework. APPROTECT provides full IP and copy/reverse engineering protection through an optional
WIBU-Systems security chip. For more information, contact Kontron Support.
1 2
3
4
5
6
KBox A-150-APL - User Guide, Rev. 1.6
www.kontron.com // 20
4/ System Overview
This user guide specifies the main technical features of the KBox A-150-APL, DIN rail industrial computer platform and
includes detailed information and guidelines for set up, assembly, installation, maintenance, transport and storage.
Before working with the KBox A-150-APL, Kontron recommends that users take a few minutes to learn about the
KBox A-150-APL’s various parts. New users are recommended to study the instructions and any warning notices
within this user guide before handling or switching on the product.
The KBox A-150-APL is a flexible fanless industrial grade DIN rail embedded box PC designed for use in performance
demanding applications requiring flexible DIN rail mounting positions in limited space, 24/7 continuous operation and
longtime industrial employment.
Based on a 3.5” Single Board Computer (SBC) using the Intel® Pentium® Quad Core™ N4200 platform, the
KBox A-150-APL features a variety of on-board interfaces to enable connectivity to nearly all applications. An internal
M.2 Key B socket supports up to 512 GBytes of memory expansion and an internal mPCIe slot enables Wi-Fi/Bluetooth
(BT) expansion. All components are selected to ensure a long lifetime and the fanless design ensures a significantly
prolonged lifespan and high system availability.
The KBox A-150-APL’s robust steel chassis is designed for horizontal or vertical operation in a DIN rail control cabinet.
The chassis height increases when the KBox A-150 APL includes an externally accessible 2.5” HDD/SSD drive bay.
Key features are:
Intel® Pentium® Quad Core™ N4200
Up to 8 GB RAM with 2x DDR3L SODIMM
Up to 512 GB memory storage via Internal M.2 SSD (option)
External 2.5” HDD/SSD drive bay (option)
External Interfaces: 1x HDMI, 1x DP, 2x GbE, 4x USB 3.0, 2x COM (RS232, RS422, RS485 configurable)
Expansion: 1x mPCIe expansion card (full-size)
Wi-Fi (2.4GHz/5GHz) /Bluetooth (4.1) combo solution (option)
Fanless passive cooling
Supports Kontron’s APPROTECT (option)
Figure 2: KBox A-150-APL Drive Bay Variant
Protection label
The KBox A-150-APL is factory configured to meet customer requirements and then sealed
with a protection label. Opening the KBox A-150-APL invalidates the warranty and may
cause damage internal components.
The KBox A-150-APL is designed for horizontal or vertical operation in a DIN rail control
cabinet.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

kontron KBox A-150-APL User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI