Important Information
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved.
Neither this manual, nor any of the material contained herein, may be
reproduced without the express written consent of the manufacturer.
Disclaimer
The information in this document is subject to change without notice. The
manufacturer makes no representations or warranties with respect to the
contents hereof and specifically disclaims any implied warranties of
merchantability or fitness for any particular purpose. Further, the
manufacturer reserves the right to revise this publication and to make
changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft
Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered
trademarks of Intel Corporation.
VGA, OS/2, PS/2 are registered trademarks of International Business
Machines.
AMD, K5, K6 are registered trademarks of Advanced Micro Devices Inc.
Cyrix, M1 are registered trademarks of Cyrix Corporation.
Other product names used in this manual are the properties of their
respective owners and are acknowledged.
Version 1.0
Safety Compliance
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment onto an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and shielded AC power cable must be
employed with this equipment to insure compliance with the pertinent RF
emission limits governing this device. Changes or modifications not
expressly approved by the system’s manufacturer could void the user’s
authority to operate the equipment.
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject
to the following conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including
interference that may cause undesired operation.
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian
Interference-causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Réglement sur le matériel brouilieur du Canada.
Contents
Chapter 1: Introduction.............................................. 1
Welcome....................................................................... 1
About the Manual.......................................................... 2
Checklist ....................................................................... 3
Standard Items------------------------------------------------- 3
Recommendations........................................................ 3
Features........................................................................ 4
Chapter 2: Installation................................................ 7
Quick Installation Table ................................................ 7
Quick Jumper Setting Reference ................................. 8
Before You Begin.......................................................... 10
Static Electricity------------------------------------------------ 10
Choosing a Case---------------------------------------------- 10
How to Set Jumpers ------------------------------------------ 11
Preparing the Mainboard .............................................. 12
Mainboard Guide---------------------------------------------- 12
I/O Ports Side View ------------------------------------------- 14
Check the Jumper Settings --------------------------------- 15
Install the Mainboard in the Case................................. 17
Connecting Power, Chassis Fans,
and Switches and Indicators ------------------------------- 19
Install Other Hardware.................................................. 21
Install the Processor------------------------------------------ 21
Installing a Socket-370 Processor ------------------------ 22
Install the Memory Modules -------------------------------- 24
Install a Hard Disk Drive and CD-ROM------------------ 25
Installing a Floppy Diskette Drive ------------------------- 27
Using the Expansion Slots ---------------------------------- 29
Add-in Card Options------------------------------------------ 30
Install Options and Extension Brackets------------------ 31
Make the External Connections ................................... 35
External Connector Color Coding ------------------------- 36
Chapter 3: Setup......................................................... 37
About the Setup Utility .................................................. 37
Starting the Setup Utility------------------------------------- 37
How to Flash a New BIOS ---------------------------------- 39
Standard CMOS Features Option ................................ 40
Advanced BIOS Features Setup Option....................... 42
Advanced Chipset Features Option ............................. 45
Integrated Peripherals Option....................................... 47
Power Management Setup Option ............................... 50
PNP/PCI Configuration Option ..................................... 53
PCI Health Status Option ............................................. 54
Frequency Control Option ............................................ 55
Load Fail-Safe Defaults Option .................................... 56
Load Optimized Defaults Option................................... 56
Set Supervisor and User Passwords............................ 56
Save And Exit Setup Option ......................................... 57
Exit Without Saving Option........................................... 57
Chapter 4: Software.................................................... 58
About the Software ....................................................... 58
Folders for this Mainboard............................................ 58
Running the Support CD-ROM..................................... 60
Utility Folder Installation Notes ..................................... 60
CMI8X38 Folder Installation Notes............................... 61
Audio Software -------------------------------------------------61
Modem Driver and Software --------------------------------62
Peripheral Folder Installation Notes ............................. 62
Intel Folder Installation Notes ....................................... 62
Mainboard (KOB 810e FSFx) Installation Notes ......... 63
Appendix 1: Quick Jumper Setting Reference ........ 64
C
Ch
ha
ap
pt
te
er
r
1
1:
:
I
In
nt
tr
ro
od
du
uc
ct
ti
io
on
n
Welcome
Congratulations on purchasing the KOB 810e FSFx mainboard.
The KOB 810e FSFx mainboard is a Flex-ATX mainboard that uses 4-
layer printed circuit board and measures 228mm x 190mm. The
mainboard has a socket-370 processor socket. This feature means
that you can install the mainboard with a PPGA Celeron or FC-PGA
Coppermine processor. The KOB 810e FSFx is installed with the
enhanced Intel 810e chipset. The mainboard has built-in 3D graphics,
3D sound, and a V.90 modem. Two 32-bit PCI expansion slots are
provided plus a TV-Out/LCD Panel Riser slot. Two DIMM sockets are
available for the installation of up to 512 MB SDRAM memory. This
mainboard is an ideal platform for an inexpensive entry level or business
class multimedia personal computer.
1
This chapter contains the following information:
About the Manual explains how the information in this manual is
organized
Checklist comprises a list of the standard and optional components
that are shipped with this mainboard
Recommendations lists some Do’s and Don’ts from the
manufacturer to help ensure reliability and performance from this
product
Features highlights the functions and components that make this
one of the best value mainboards on the market
About the Manual
The manual consists of the following chapters:
Introduction
Use the Introduction Chapter to learn about the features of the
mainboard, and the checklist of items that are shipped with the package.
Installation
Use the Installation Chapter to learn how to install the mainboard and
get your system up and running.
Setup
Use the Setup Chapter to configure the mainboard for optimum
performance.
Software
Use the Software Chapter to learn how to use the software drivers and
support programs that are provided with this mainboard.
2
Checklist
Compare the contents of your mainboard package with the standard
checklist below. If any item is missing or appears damaged, please
contact the vendor of your mainboard package.
Standard Items
1 x KOB 810e FSFx Mainboard
1 x Cable/Bracket Pack
Diskette drive ribbon cable
IDE drive ribbon cable
This User’s Manual
Software Support CD-ROM Disc
Optional items
1 x V.90 Fax/modem Card
1 x TV-Out Riser Card
Recommendations
This mainboard automatically determines the CPU clock frequency and
system bus frequency for the kind of processor that you install. You may
be able to change these automatic settings by making changes to
jumpers on the mainboard, or changing the settings in the system setup
utility. We strongly recommend that you do not overclock the mainboard
to run processors or other components faster than their rated speed.
Overclocking components can adversely affect the reliability of the
system and introduce errors into your system. Overclocking can
permanently damage the mainboard by generating excess heat in
components that are run beyond the rated limits.
Components on this mainboard can be damaged by discharges of static
electricity. Handle the board carefully holding it by the edges. Don’t flex
or stress the circuit board. Keep the board in its static-proof packing until
you are ready to install it. Follow the static guidelines given at the
beginning of Chapter 2.
3
Features
The key features of this mainboard are the wide range of processors that
can be installed, and the high level of integration which includes built-in
audio, video, and communications.
Value-class Processors
As a platform for a value PC, the KOB 810e FSFx includes a socket-370
for the installation of the latest PGA and FC-PGA packaging processors
form Intel.
The PGA Celeron processors ship in the familiar square plastic package,
and they install in a Zero Insertion Force (ZIF) socket called Socket-370.
These PGA Celeron processors are close to Pentium II performance
because they include a level-2 cache memory of 128K. However, they
operate over a 66MHz system bus and they currently ship at clock
speeds of up to 533MHz. The PGA Celeron is the premiere choice for
an entry-level PC.
The FC-PGA Coppermine processor operates over a 66, 100 or 133
MHz system bus. The FC-PGA Coppermine ships with clock speeds
running from 500 MHz through to 750 MHz.
The KOB 810e FSFx supports 66MHz (PGA Celeron) as well as 100
MHz and 133 MHz front side buses (FC-PGA Coppermine).
Intel’s 810e Chipset
This board features 810e chipsets from Intel. The 810e chipset is
designed to reduce the cost and improve the multimedia capability of
value PCs. The chipset features an integrated AGP (Accelerated
Graphics Port) graphics controller that is optimized to produce smooth
rendition of 2D and 3D video. Digital video output is supported so that
the system can display on a TV or a flat-panel display with digital video
input. The graphics controller improves performance and reduces cost
by dynamically allocating a segment of active memory as video memory.
The 810e I/O chip (82801 I/O Controller Hub) makes a direct connection
between the graphics system and the IDE controller and the PCI bus. It
uses Accelerated Hub Architecture to effectively double the bandwidth
between these components enabling more life like audio and video. It
includes an integrated Audio-Codec controller (AC97) that lets the
processor more effectively decode sound generated by the integrated
audio system or the integrated fax/modem. Finally, the 82802AB
4
Firmware Hub allows the system and video BIOS to be stored
(eliminating the need for non-volatile CMOS memory) for faster
execution, and provides a random number generator to enable strong
encryption routines.
Inexpensive Memory
The board has two DIMM sockets for the installation of 168-pin, 3.3V
non-buffered DIMM memory modules. The DIMM memory modules must
be installed with SDRAM memory chips. The KOB 810e FSFx board
supports a memory bus of 100 MHz and 133 MHz. Each installed
memory module can be populated with 8 MB up to 256 MB of memory,
so a maximum total of 512 MB memory can be installed. The integrated
video system uses a shared memory architecture so that you must
reserve some of the installed memory as video memory using the
system BIOS. You must install at least one memory module, and the first
memory module is installed in DIMM1.
Highly Integrated Design
As well as the Intel 810e chipset, the KOB 810e FSFx features other
highly integrated silicon chips. The ITE LPC I/O controller handles the
mainboard’s I/O functions. The CMI 8738/PCI C3DX is a two-chip
solution that provides an integrated audio and fax/modem system.
Built-in AGP 3D-Graphics
The Intel 810e chipset includes an integrated AGP controller that is
optimized for smooth 2D and 3D video. The graphics system shares
active memory and does not require dedicated video memory. Video is
delivered through a regular 15-pin connector.
Built-in PCI 3D Sound
The PCI Audio CMI 8738 is a single chip solution for PCI-bus 3D audio.
The chip provides Sound Blaster 16-bit-compatible audio, plus support
for Microsoft’s DirectSound 3D specification and Aureal A3D interface.
The sound ports include jacks for speakers, microphone and stereo in,
and a game/MIDI port. The audio system supports full duplex operation
and drivers are available for WIN 95/98 and WIN NT 4.0. The audio
system can output sound to 4 loudspeakers.
Built-in V.90 Fax/modem (DAA Module is optional)
The KOB 810e FSFx mainboard has a built-in 56 Kbps fax/modem that
supports the V.90 protocol. The chip is integrated with the built-in audio
system to support voice as well as data transmissions. In order to use
the built-in fax/modem, you must install a DAA module that supplies the
RJ11 sockets for LINE and TELEPHONE.
5
Expansion Options
The KOB 810e FSFx mainboard is pre-installed with features such as
audio, video and an optional DAA module for a modem, that normally
require add-in cards, so the two 32-bit PCI slots provide plenty of
expansion potential. The KOB 810e FSFx PCI slots support UDMA 66
bus mastering. The mainboard also has TV-Out and LCD Riser slot for
exporting the system video output to an external TV receiver or LCD
panel.
Integrated I/O
The mainboard has a full set of I/O ports and connectors. The I/O
template on the backplane includes two PS/2 ports for mouse and
keyboard, one serial port, one parallel port, one VGA monitor port, one
game/MIDI port, two USB ports and audio jacks for microphone, line-in
and line-out. The board has a header for the optional installation of an IR
port, and second serial port. The board includes two PCI IDE channels
and a floppy disk drive interface.
Keyboard Power On Feature
Using the system BIOS setup program, you can configure the system to
turn on using a keyboard-typed password. A green keyboard is not
required.
Programmable Firmware
The mainboard includes Award BIOS that allows BIOS setting of CPU
parameters. The fully programmable firmware enhances the system
features and allows users to set power management, CPU and memory
timing, LAN and modem wake-up alarms, and so on. The firmware can
also be used to set parameters for different Celeron processor clock
speeds so that you don’t need to change mainboard jumpers and
switches.
6
C
Ch
ha
ap
pt
te
er
r
2
2:
:
I
In
ns
st
ta
al
ll
la
at
ti
io
on
n
Quick Installation Table
This chapter explains how to successfully install the mainboard into a
computer case and build a working system. The installation procedure is
as follows:
Quick Jumper
Setting Reference
Provides a quick reference for the jumper
settings on this mainboard.
Before you Begin Provides advice on choosing a case,
avoiding static electricity damage, and setting
jumpers.
Preparing the
Mainboard
Provides a guide to the mainboard and I/O
port locations, full details on the jumper
settings, and advice on installing the
mainboard in the system case.
Install Other
Hardware
Provides guidance on installing essential
hardware: processor, memory, hard disk
drive, CD-ROM, floppy disk drive, and
expansion cards.
Make the External
Connections
Provides advice on using the external I/O
ports to install peripheral devices such as a
keyboard, a monitor, a mouse, a printer,
loudspeakers, and so on.
7
Quick Jumper Setting Reference
If you are familiar with most of the material in this chapter, you can begin
preparing the mainboard for installation by using this quick reference to
begin the setting the jumpers. A detailed description of the jumper setting
appears later in this chapter.
JP1: Clear CMOS memory jumper
Use this 3-pin jumper top clear all the current data stored in the CMOS
memory.
Function Jumper Cap
Normal operation Short pins 1-2
Clear CMOS Short pins 2-3
JP1 1 2 3
JP2: Keyboard power on jumper
Use this 3-pin jumper to enable keyboard power on with hot keys or
password.
Function Jumper Cap
Disable keyboard power on Short pins 1-2
Enable keyboard power on Short pins 2-3
1 2 3
JP2
JP3: Force 100 MHz front side bus jumper
Use this jumper to disable the automatic detection of the correct front
side bus, and force the system to run with a 100 MHz front side bus.
Function Jumper Cap
Normal operation Short Pins 1-2
Force 100 MHz FSB Short pins 2-3
JP3 1 2 3
JP4: Force 133 MHz front side bus jumper
Use this jumper to disable the automatic detection of the correct front
side bus, and force the system to run with a 133 MHz front side bus.
Function Jumper Cap
Normal operation Short Pins 1-2
Force 133 MHz FSB Short pins 2-3
JP4 1 2 3
8
PANEL1: Panel connectors for switches and indicators
Use the panel connector to implement the switches and indicators on
your system case.
Function Pins
Speaker 1, 3, 5, +7
Power Indicator +2, +4, 6
Keylock 8, 10
Green Indicator +13, 14
Hard Disk Indicator +15, 16
Reset Switch 17, 18
Suspend Switch 19, 20
Power Switch 21, 22
PANEL1
HDD LED
Green LED
Reset SW
Suspend SW
Power SW
KeyLock
Power LED Speaker
22 21
2 1
9
Before You Begin
Before you begin to install your KOB 810e FSFx mainboard, take some
precautions to ensure that you avoid the possibility of damage to the
product from static electricity. Ensure too that you are installing the
mainboard into a suitable case.
Static Electricity
In adverse conditions, static electricity can accumulate and discharge
through the integrated circuits and silicon chips on this product. These
circuits and chips are sensitive and can be permanently damaged by
static discharge.
♦ If possible wear a grounding wrist strap clipped to a safely
grounded device during the installation.
♦ If you don’t have a wrist strap, discharge any static by touching
the metal case of a safely grounded device before beginning the
installation.
♦ Leave all components inside their static-proof bags until they are
required for the installation procedure.
♦ Handle all circuit boards and electronic components carefully.
Hold boards by the edges only. Do not flex or stress circuit
boards.
Choosing a Case
The mainboard complies with the specifications for the FlexATX system
case, although it can also be installed in most micor-ATX case designs.
The FlexATX specifications include a maximum size of 9.0” x 7.5”
(229mm x 191mm), a reduced number of expansion slots, and support
for a smaller power supply unit.
Some features on the mainboard are implemented by cabling connectors
on the mainboard to indicators and switches on the system case. Ensure
that your case supports all the features required. The KOB 810e FSFx
mainboard can support one or two floppy diskette drives and four
enhanced IDE drives. Ensure that your case has sufficient power and
space for all the drives that you intend to install.
10
The mainboard has a set of I/O ports on the rear edge. Ensure that your
case has an I/O template that supports the I/O ports and expansion slots.
How to Set Jumpers
A jumper consists of two or more pins mounted on the mainboard. Some
jumpers might be arranged in a series with each pair of pins numbered
differently. Jumpers are used to change the electronic circuits on the
mainboard. When a jumper cap is placed on two jumper pins, the pins
are SHORT. If the jumper cap is removed (or placed on just a single pin)
the pins are OPEN.
This illustration shows a 2-pin jumper. When the
jumper cap is placed on both pins, the jumper is
SHORT. If you remove the jumper cap, or place the
jumper cap on just one pin, the jumper is OPEN.
OPEN
SHORT
This illustration shows a 3-pin jumper. The jumper cap is
placed on pins 2 and 3, so this jumper setting is SHORT
PINS 2-3.
This illustration shows the same 3-pin jumper. The jumper
cap is placed on pins 1 and 2, so this jumper setting is
SHORT PINS 1-2.
In this manual, all the jumper illustrations clearly show the pin numbers.
When you are setting the jumpers, make sure that the jumper caps are
placed on the correct pins to select the function or feature that you want
to enable or disable.
11
Preparing the Mainboard
Mainboard Guide
Use the following illustration and key to identify the components on your
mainboard.
JHD1
CASFAN1
CPUFAN1 DIMM1 DIMM2
JP2
JP4 FDD1
IDE2
IDE1
PANEL1
SIR1
WOM1
WOL1
JP1
J1
FP1
CD2
TV-Out/LCD Panel Riser Slot
CD1
Socket-370
PCI1
PCI2
A
TX1
COM2
LED1
J2
JP3
USB1
LED2
MODEM2
12
Key to Mainboard Components
Component Description
Socket-370 Socket for PPGA Celeron Processor
PCI 1, 2 Two 32-bit PCI Slots
TV-Out/LCD
Panel Riser
Slot for a TV-Out/LCD Panel Riser card.
DIMM 1, 2 Two slots for 168-pin SDRAM memory module
FDD1 Connector for floppy disk drives
IDE1, IDE2 Primary and secondary IDE channels
ATX1 Connector for ATX power supply
SIR1 Connector for optional infrared port
PANEL1 Panel connector for switches and indicators
WOM1 Connector for modem wake up
WOL1 Connector for LAN wake up
USB1 Connector for auxiliary USB ports
*LED1 3VSB LED for SDRAM
**LED2 Power LED
COM2 Connector for serial port 2/4
CASFAN1 Power connector for case cooling fan
CPUFAN1 Power connector for CPU cooling fan
MODEM2 Connector for modem DAA module
CD1 Audio connector for CD-ROM/DVD drive
CD2 Auxiliary audio connector for CD-ROM/DVD drive
JHD1 Auxiliary keyboard connector
FP1 Auxiliary microphone and speaker out
J1 Chassis open detect connector
J2 Connector for two-color LED
JP1 Clear CMOS memory jumper
JP2 Keyboard power on jumper
JP3 Force system bus frequency to 100 MHz jumper
JP4 Force system bus frequency to 133 MHz jumper
*LED1
The red indicator LED1 turns on if your system is still powered. It means
you can’t install or un-install your memory modules when LED1 turns on.
**LED2
This green indicator turns on whenever the system is turned on. It warns
you that the system is active and you should not carry out any work on
the mainboard.
13
I/O Ports Side View
PS2KBM
USB1 COM1 VGA1 JS
JSLPT1
Key to I/O Ports
Component Description
PS2KBM PS/2 port for pointing device (upper port)
PS/2 port for keyboard (lower port)
LPT1 External parallel port
JS (Upper) External game/MIDI port
JS (Lower) Audio jacks for (from left to right) line out, line
in, microphone
VGA1 External monitor port
COM1 External serial port COM1/3
USB1 Two stacked Universal Serial Bus ports
14
Check the Jumper Settings
Check all the mainboard jumpers to ensure that the board is configured
correctly.
JP2 JP3
JP4
JP1
JP1 Clear CMOS Memory Jumper
This jumper lets you erase the system setup settings that are stored in
CMOS memory. You might need to erase this data if incorrect settings
are preventing your system from operating. To clear the CMOS memory,
turn off the system, disconnect the power cable from the mainboard, and
short the appropriate pins for a few seconds.
Function Jumper Cap
Normal Operation Short pins 1-2
Clear CMOS Short pins 2-3
JP2: Keyboard Power On Jumper
This jumper lets you use a typed-in password as a power switch to turn
your system on. If you enable this property, you need to define the
password or the hot keys using the setup utility. See Chapter 3.
Function Jumper Cap
Disable keyboard power on Short pins 1-2
Enable keyboard power on Short pins 2-3
1 2 3
1 2 3
JP2
JP1
15
JP3: Force 100 MHz Front Side Bus Jumper
Use this 3-pin jumper to disable the automatic detection of the correct
front side bus (FSB), and force the system to run with a 100 MHz front
side bus.
1 2 3
JP3 Function Jumper Cap
Normal operation Short pins 1-2
Force 100 MHz FSB Short pins 2-3
JP4: Force 133 MHz Front Side Bus Jumper
Use this 3-pin jumper to disable the automatic detection of the correct
front side bus (FSB), and force the system to run with a 133 MHz front
side bus.
Function Jumper Cap
Normal operation Short pins 1-2
Force 133 MHz FSB Short pins 2-3
1 2 3
JP4
16
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
