Hoover UH70085 Owner's manual

Type
Owner's manual

This manual is also suitable for

Owner's Manual
Operating and Servicing Instructions
www.hoover.com
®
Pleasereview this manual before operating your Hoover® product.
©2009 Healthy Gain ]nwstments, Lid,, A11rights reserved_ #17-01-58-05B-OO-H301-RI 2/09
Thank you for choosing
Please enter the complete model and serial
numbers in the spaces provided.
Model
Serial Number
Hint: Attach your sales receipt to this owner's
manual. Verification of date of purchase
may be required for warranty service of' :/our
HOOVER ® product.
a HOOVERproduct.
Be sure to fill out and return the product registration card included with "your cleaner.
Contents
Important Safeguards ......................................................... 3
Cleaner Assembly ............................................................... 4
Carton Contents ..................................................... 4
How To Use.............................................................5-9
Cleaner Descriptions ......................................................... 5
Cleaning Tools ...................................................... 7-8
Maintenance........................................................ 8-13
Dirt Cup ............................................................ 8-9
Filters ..............................................................9-I0
Headlight ......................................................... 10
Belt .................................................................II
Agitator Brushroll .................................................... 12
Powered Hand Tool ................................................ 12-13
Agitator BrushrolI ............................................... 12-13
Power Hand Tool Belt ..................................................13
Lubrication ............................................................ 14
Thermal Protector ..........................................................14
Authorized Service .........................................................14
Troubleshooting ......................................................... 15
Clearing Blockages ..................................................... 16
Warranty .................................................................. 17
lfyou need assistance:
Visit our website at hoover, com. Follow the authorized dealer locator link to find the Hoover ® authorized
dealer nearest you or call 1-800-944-9200 for an automated referral of Hoover ® authorized dealer
locations (uoS.Only] or to speak with a customer service representative; Mon- Fri 8am- 7pro est, Please
do not return this product to the store.
This carpet cleaner is intended for household use.
Not intended for commercial use in any household or for any other commercial purpose, Operate carpet
cleaner only at voltage specified on data plate on back of cleaner.
Plug carpet cleaner into a properly grounded outlet.
important Safety Instructions
When using an electrical appliance, always follow basic precautions, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
WARNING: To reduce the risk of fire, electric shock, or injury:
Do not use outdoors or on wet surfaces.
Close supervision is necessary when any appliance is used by or near children. Do not
allow vacuum cleaner to be used as a toy or to run unattended at any time.
o Keep hair, loose clothing, fingers, feet and alI parts of body away from openings, rotating
agitator and other moving parts,
. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
o Do not use to pick up flammable or combustible materials such as gasoline or fine wood
sandings or use in areas where they may be present.
o Always turn off this appliance before connecting or disconnecting hose_
o Unplug cleaner before connecting the powered hand tool
o Do not use without dirt cup or filters in place. Empty cup and clean filter frequently
when picking up very Fine materials such as powder,
"Use extra care when cleaning on stairs_
o Do not put any object into openings. Do not use with any opening blocked; keep free of
dust, lint, hair, or anything that may reduce air flow.
o Always disconnect cord from electrical outlet before servicing the cteaner.
o Unplug cleaner when not in use_ Turn off alI controls before unplugging.
° Do not unplug by pullingon cord,,To unplug,graspthe plug,not the cord_Never handle
plug or appliance with wet hands.
o The use of an extension cord is not recommended.
_, Do not use with damaged cord or plug. if appliance is not working as it should, has been
dropped, damaged, Ieft outdoors, or dropped into water, take it to a Hoover Sales and
Service Center or Authorized Hoover Warranty Service Dealer {Depot)_
,, Do not pull or carry, by cord, use cord as a handle, dose door on cord or pull cord around
sharp edges or comers_ Do not run appliance over cord. Keep cord away From heated surfaces.
o Use vacuum cleaner only for its intended use as described in the instructions. Use onty
attachments recommended by Hoover; others may cause hazards.
o Hotd plug when rewinding cord onto cord ree!o Do not allow plug to whip when rewinding_
WARNING:
o This product contains chemicals known to the State of CaIifornia to cause cancer and
reproductive toxicity. Wash hands after handling,
e Do not operate cleaner in bare feet or when wearing open toe shoes or sandats_
o Avoid picking up hard, sharp objects with the cleaner. They may damage the cleaner.
Save these instructions!
Carton contents
A_ Handle section
B. Cleaner base and upper housing assembly
C. Cleaning tools and wands"
D. Powered Hand Tool
Remove all parts from carton and identify each
item shown.
Make sure all parts are located before disposing of
packing materials.
"Tools may vat), per model
Attach handle
Using a Phillips screwdriver, remove (2) screws from the top of
theupperhousingassembly.
Insert handle section (A) into upper housing assembly, Push down
firmly until you hear a click_
Fasten (2) screws on either side of handle base,
Position Tools
A
Place smaller diameter
end of wand (A} into
bottom of rack, Snap
wand into clip at top,
Repeat with other wand_
Crevice tool {B)fits into
one of the extension
wands,
Fit Upholsterytool (C}
into storage areaon side
ofcleaner asshown.
A
Fit powered hand tool (A)
into recessed area on front
of cleaner, Pivot toward
handle to snap in place.
Cleaner Description
I. Soft ToucW_ handle grip
2_ ON/OFFswitch
3. Hose
4_ Dirt cupreleasebutton
5_ Dirt cup assembly
6. Hosehandle
7. Cord reel window
8_ Headlight
9, Nozzle controlknob: turn knob
to correct setting for height of
carpet being cleaned,
10, Furniture guard: helps prevent
cleaner from marking furniture.
11_Agitator brushroll
shut-off pedal
12, Agitator brushrotl
shut-off indicator
13. Final filter access
14. Upholstery tool*
t5. Powered hand tool
15. Crevice tool
!7. Hosettool holder
18,Wands
19, Cord reel
20. Soft TouchTM wheels
2t, Handle release pedal: step
on lever to lower handle to
operating or low positions.
22. Cord rewind button: press
button to rewind cordfor
storagerHold plug until cord is
rewound.
"lbols may vary per modeL
t4
22
2
1t
Operate cleaner only at voltage specified on data plate on
back of cleaner.
This cleaner is intended for household use_
16
17
IB
19
20
Polarized plug
To reduce the risk of electric shock, this appliance has a
polarized plug {one blade is wider than the other}. This plug
will fit in a polarized outlet only one way. tf the plug does
not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet,
Do notchangetheplugin anyway,
ON-OFF Switch
Plug cord into electrical
outlet.
To turn cleaner ON, push
ONf0FF switch once.
To turn cleaner OFF,push
switch again.
Brushroll Switch
The cleaner is shipped
with the agitator
brushroll in the OFF
position. To turn the
agitator brushroll
ON, step on the pedal
(A). The indicator (B)
will show red in the
"brushrolt on" window.
Cord
Rewind
Graspthe end
of theplug
and pull to
releasecord
from cord
reel, After
desired cord
length is
reached, the
cord will lock
into position.
To return corcl for storage, hold plug
and press on button (A}at top of cord
reel. To prevent cord from whipping,
hold plug until cord is rewound,
Transporting
Cleaner
To move your cleaner
from room to room,
put handle in upright
position,tiltcleaner
back on rear wheels
and push forward.
Handle
Positions
The handle
ofyour
cleaner
has three
positions;
upright for
storage and
when using
cleaning
tools;
operating
position for general operation on
carpet and floors; tow for reaching
under low furniture° Step on handle
release lever to lower handle,
Carpet Height
AdJustment
The cleaning
of carpet and
rugs takes
place at the
nozzte (A},
When it is
necessary
to raise and
lower the
nozzle for
various carpet pile heights, turn
the nozzle control knob (B) to the
desired setting.
Settings
For maximum cleaning performance,
the following carpet height settings
,m. Low are recommended:
o Lowest setting: for all types of
carpet,
Note: tf the cleaner is difficult to
push, turn knob to the next higher
setting.
o Higher settings: forvery deep
pile carpet, where easier pushing effort is desired, while
maintaining good cleaning performance.
Agitator Brushroll Shut-Off
The agitator brushroll shuts off automatically for tool use,
when the cleaner is in the upright position.
To manually shut off the agitator brushrotl for cleaning hard
floors, step on the pedal (A).The indicator (B) willshow red
in the "brushrolI off" window. To turn the agitator brushroll
on, step on the pedal again. The indicator will show red in the
"brushroll on" window_
Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas,
The cleaner is ready for tool use when handle is in upright position.
The agitator brushroll will not rotate when the cleaner is in the upright position or the if the agitator
brushroll shut off indicator is in the OFF position when the handle is lowered°
Removing Hose
When using
cleaning tools,
place cleaner
handle in
the upright
position.
The agitator
brushroll will
not rotate when
the cleaner is
in the upright
position,Also,turn cleaner OFF before
disconnecting and connecting hose to
hose tube [A)..
Tousehose,lift hoseend (B) asshown.
When you are finished cleaning with the
tools,reposition hose end into tube-
Select Proper Tool
D
EV
A. UseUpholstry
tool' to clean
upholstered
furniture, draperies,
mattresses,clothing,
and carpeted stairs°
B,Powered hand
toolmay be used
Forupholstered
furniture, draperies,
mattresses, clothing, automobile interiors, and carpeted
stairs.
C. Crevice tool may be used in tight spaces, corners and
along edges in such places as dresser drawers, upholstered
furniture, stairs and baseboards°
Dr Wands are used to give extra length to your hose. Use
them with any of the above tools.
"Toolsmay varyper modeL
Attach Wand and
Tools
How to
Clean Tools
To clean the hose and powered hand tool, wipe off dirt with
a cloth dampened in a mild detergent. Rinse with a damp
cloth. DO NOT submerge powered hand tool in water.
Cleaning tools may be washed in warm water with a
detergent° Rinse and air dry before using.
Attach tool or wand to the hose (A)-
Attach tool to wand {B) by pushing it
firmly onto the wand.
Twist wand or too] stighfly to tighten
or loosen the connection,
Combination Tool
Available on some models only)
A
Stair Cleaning
Use the hose and powered hand tool for stair
cleaning. Clean from bottom to top.
CAUTION-' To avoid personal injury or unnecessary
wear to carpet, and to prevent the cleaner from
falling, always place it at bottom of stairs.
Slide brush to remove_
To replace brushes, align bottom of brush with
grooves (A) on toot. Slide brush into place.
Extra ReachTM Hose
(available at additional cost}
The Extra Reach TM hose provides easier cleaning
of stairs and hard to reach places. Follow the
steps below for attaching and detaching the
Extra Reach TM hose.
/h
fl
Turn cleaner OFF before disconnecting and
connecting hose, Remove hose end From dirt
duct (A), Align end of Extra ReachTM hose with
projections (B) over slots on dirt duct {C)oSlide
hoseinto slots and twist hoseto lock it into
place.
Alignend ofhosewithprqjections[D)overslots
{E} on Extra Reach_ hose,Slide hose into slots
and twist hose tolock it into place_ [Todetach
hose, reverse procedure},
Attach wands or toolsto the other end of hose,
Note: Hose must be connected to dirt duct and
hose tube after removing Extra Reach" hose for
carpet or floor cleaning.
Familiarize yourself with these home maintenance tasks as proper use and care ofyour cleaner will
ensure continued cleaning effectiveness,
Dirt Cup
When to Empty
Empty the dirt cup before the dirt reaches the fill line (A)°
Place the cleaner in the uptight position before removing
the dirt cup-
Disconnect cleaner from electrical outlet. Do not use cleaner
without dirt cup or filters in place,
CAUTION: Very fine materials, such as face powder or
cornstarch, may seal the filter and cause a reduction in
performance. When using the cleaner for this type of dust,
empty the cup and clean the filters often,
Dirt Cup (cont.)
How to Empty
Press dirt cup release button (A) and pivot
cup oub
Holding dirt cup over trash receptacle, press
dirt cup door release button (A) to open dirt
cup door (B),
Close door and press dirt cup door release
button to latch dirt cup door closed,
Place bottom of dirt
cup into cteaner
body firsL Pivot cup
into cleaner body,
Press on dirt cup
release button while
firmly pressing on
dirt cup_
Release button in
order for it to return
toproper position
and lock the dirt
cup into place,
Filters
Cyclonic Filter Assembly: How to Clean
Disconnect cleaner from electrical outlet. Do not use cleaner without dirt cup or filters in place,
_B
Remove dirt cup as described in Fig_ 4-2_
Twist filter assembly (A} counterclockwise.
Remove assembly from dirt cup.
Dirt and debris can be cleaned from the
filter assembly by brushing with the cleaner's
combination tool
Place the filter assembly on the dirt cup,
aligning (3) tabs (A) on filter with (3) slots on
dirt cup (B) and twist it clockwise to secure into
position. Press dirt cup door release button (C}
to ]atch dirt cup door closed.
Replace dirt cup as described in Pigs_ 4-4 Et 4-5_
Filters (cont.)
Seeondary Filter: How to Clean
Disconnect cleaner from electrical outlet. Do not
use cleaner without dirt cup orfilters in place.
Remove dirt cup as described in Fig. 4-2.
With thumb and forefinger, slide latch (At located at the
top of the housing to the right and pull down to remove
gray filter frame. Remove black foam filter. Rinse filter
frame cartridge and foam filter under cold water,
Allow both filter frame and filter to air dry for 24 hours
before replacing filter intofilter flame, Reposition filter
frame cartridge by inserting tabs into slots on back of
housing_ Rotate filter cartridge frame up toward top of
housing and snapclosed.
Secondary Filter: What to Buy
When purchasing a new secondary filter cartridge, ask for HOOVER®part No. 93002517.
Topurchase a new black foam filter, ask for HOOVER®part Noo930025tB.
HEPA Final Filter: How to Clean
Disconnect cleaner from electrical outlet. Do not use cleaner without dirt cup or filters in place.
With fingers in slots, pull filter
frame (A)straight out.
Dirt and debris can be cleaned from
thefilter cartridgebybrushing with
the cleaner'scombination tool.
HEPA Final Filter: What to Buy
When purchasing a new HEPA filter
cartridge, ask for HOOVER®part No_
93002360°
DO NOT R1NSE OR WASH the
HEPA filter cartridge€
Slide back into position on cleaner,
Headlight
Disconnectcleaner from electrical outlet,
Removing Lens Installing Bulb Replacing Lens
Press handle release pedal and place handle
in low position.
Using a Phillipsscrewdriver, remove the the
screw asshown and lift off lens,
Headlight: What to buy
This cleaner uses a 13 volt, T-3 114 wedge
base bulb, When purchasing a new tightbulb,
ask for Hoover part No, 27313-t07
t0
Pul!oldbulbstraight
outofsocket,Push
new bulbstraight
into socket until
locked in place.
Excessive Force is
not required.
Reposition lens and
secure with the screw.
Belts
Disconnect cleaner from electrical outlet.
WARNING; Agitator brushroll can start suddenly. Unplug cleaner before turning it over,
The belts are located under the bottom plate of the cleaner and should be checked from time to time
to be sure they are in good condition,
Replacing Flat Belt
Replace bett if it is stretched, cut or broken_ To check the flat belt, refer to Fig_ 4-t3_
Removing Bottom
Plate Removing Belt Positioning Belt
Place handle in low
position and turn
cleaner over so bottom
side is facing up.
Remove the 6 screws as
shown with aPhillips
screwdriver,
Lift offbottom plate.,
Remove used belt (A)
from large pulley (B}
and discard.
Flat Belt: What to Buy
Use only genuine HOOVER® belts with your
cleaner. When purchasing a new belt, ask for
Flat belt - HOOVER® part No. 4020!-271,
With lettering on
outside of belt, slide
new bett over motor
shaft (A)o
Place other end of
belt over large pulley
{B) while rotling the
pulley in direction
shown,
Turn agitator brushrol] making sure belt turns
freely and is not pinched between agitator
brushrolI and agitator shield.
Reposition bottom plate
and 6 Phillips head
screws,Tighten screws
securely,
Inspecting V-Belt
TheV-belt isdesigned to last for a long time and
is not normally replaced. However, ifthe V-belt is
cracked, gouged or broken, it should be replaced.
Slide flat belt off large pulley as shown in Fig, 4-14_
To remove V-belt, slide back of belt over pulley (A].
Then firmly pull on belt and "snap" it out,
Discard usedbelt.
To install new belt (with lettering on outside of
belt), slide back of belt over pulley and pu11front of
belt toward groove (B) next to pl,tley. Belt will "pop" into place.
V-Belt: What to Buy
Use only genuine HOOVER®belts with your cleaner. When purchasing a
new belt, ask for V belt -HOOVER ®part No. 40201-200.
lnsert agitator
brushroll through belt
and position belt in
groove (A) on agitator
brushrolI,
11
Agitator Brushroli
Disconnect cleaner from electrical outlet,
WARNING: Agitator brushroll can start suddenly. Unplug cleaner before turning it over.
Replacing Agitator Brushroll
When agitator brushes are worn, the brush roll should be replaced
Inspecting Agitator Brushroll
To check condition of
brushes, move edge of a
card across bottom plate
while turning agitator
brushroll, To maintain
cleaning effectiveness,
replace agitator brushroll
if brushes do not touch
card.
Removing Agitator Brushroll
Turn carpet height
adjustment knob to
lowest setting. Turn
cleaner over and remove
bottom plate (Fig. 4-13).
Lift up agitator brusilrolt
and slide V_belt {A) off
agitator brushroll.
Positioning V-Belt
insert agitator brushrolI
through belt and
position belt in groove
{A) on agitator brushrolL
Agitator Brushroll: What to Buy I
When purchasing a new Agitator Brushrotl, ask for
I
HOOVER® part No. 9300236L
Installing Agitator
B
Reposition fiat belt and
to 4-16),
Brushroll
Grasp agitator brushroll
firmly and fit it into
position by firstsliding
end opposite the belt into
the rectangular slot [A]
on side of cleaner.
Pull other side of agitator
brushroll (B) into place.
Belt may fit loosely when
properly installed,
bottom plate (Figs, 4-15
Powered Hand Tool
Replacing Agitator Brushroll
When agitator brushes are worn, the brushrolt should be replaced,
How to Replace
A
Turn tool sobottom
faces up_ Press the
latcheson either side of
tool and remove bottom
plate (A).
Unscrew the two Phillips screws and remove
belt guard (AL
t2
Powered Hand Tool {cont.)
Replacing Agitator Brushroll
How to Replace
Remove agitator
including end plates (A)
and discard,
lnspect belt to ensure
that it is in good
condition. If belt is
cracked, gouged or
broken, replace it (see
Following section).
lnsert brushro]] through
belt and position belt over gear teeth (B} on
brushroll,
To replace bottom plate,
insert the four tabs on
edge of bottom plate into
slotson front of toolo
Pivot bottom plate down
and snap closed.
With curved ends
down, slide end plates
(A)of brushroH into
slots (B}on tool.
Replace belt guard (A)
making sure not to
pinch brush bristles in
guar& Turn agitator,
to make sure it rotates
Freely.
Replace and tighten
screws.
Agitator Brushroll: What to Buy
When purchasing a new Powered Hand Tool
Agitator BrushroH, ask for HOOVER ®part No,
48414-088_
Belt Replacement
The powered hand tool belt is designed to last a long time and is not normally replaced° However, if
the belt is cracked, gouged or broken, it should be replace&
Inspecting the Replacing the
Belt Belt
The belt can be seen
through the top of the
nozzle or by removing
thebottom plate and
belt guard (Figs, 4-23
to 4-24).
Grasp turbine (A) and
pulI firmly to remove,
Remove belt from
turbine pulley (B),
RepIace with new belt.
B
With flat sides of
turbine retainers (A)
pointing down, slide
retainers into grooves
[B} in tool housing and
snap into placer
Replace brushroll, belt
guard, and bottom plate
asdescribed in _igs.
4-25 through 4-28,
Powered Hand Tool Belt: What to Buy
When purchasing a new Powered Hand Tool
Belt, ask for HOOVER part No, 38528-O3Z
13
Lubrication
The motor is equipped with bearings that contain sufficient lubrication for the life of the motor The
addition of lubricant could cause damage, Therefore, do not add lubricant to motor bearings.
The agitator brushroll is equipped with two ball bearings that should be lubricated periodica]ly by a
Hoover Sales and Service Center or an Authorized HooverWarranty Service Dealer°
Thermal Protector
An internal thermal protector has been designed into your cleaner to protect it from overheating,
When the thermal protector activates, the cleaner will stop running. If this happens, proceed as
follows:
t. Turn the cleaner OFF and disconnect it from the electrical outlet°
2. Check secondary and final filters for dirt accumulation.
3o Refer to "Clearing blockages" section_
4. When cleaner is unplugged and the motor cools for 30 minutes, the thermal protector
automatically resets and cleaning may continue.
If the thermal protector continues to activate after following the above steps, your cleaner may need
servicing {see "Service" section),
Service
To obtain approved Hoover ®service and genuine Hoover ®parts, locate the nearest Authorized
Hoover ®Warranty Service Dealer {Depot) by:
* Checking the Yellow Pages under "Vacuum Cleaners" or "Household".
. Visit our website at hoover, corn (U.S. Customers} or hoover.ca (Canadian customers)_ Follow the
service center link to find the service outlet nearest you.
. For an automated referral of authorized service outlet locations call t-800-944-9200o
Do not send your cleaner to Hoover_, lnc,, Company in Glenwitlow for service° This wilt only result in delay.
If you need further assistance:
To speak with a customer service representative ca11!-800-263-5376; Mon-Pri Bam-Tpm EST. ]n
Canada, contact Hoover ® Canada, Toronto: 755 Progress Ave., Scarborough, ON M1H 2W7 ORHoover ®
Canada, Edmonton: t8 !29-111 Ave,_,Edmonton, ABT5W 2P2, Phone: t-800-263-6376, Mon-Pri 8am-
7pro ESTo
Always identify ;your cleaner by the complete model number when requesting information or ordering
parts. {The model number appears on the back of the cleaner.}
Please do not return this product to the store.
14
PROBLEM
Cleaner won't run
POSSIBLEREASON POSSIBLESOLUTION
................... ,i,................. ,,,ii_ ii,iiii,iii,i, iiiii,,iii,i,
2. Blown fuse or tripped breaker, 2. Cheek fuse or breaker in home, Replace ['use/
reset breaker,
[:leaner won't pick
up or low suction
1. Blockage in air flow passages.
3, Agitator Brushroll worn,
5. Clogged filter,
t Clear blockage - Pg 115
3 Replace Agitator Brushroll - Pg. t0,
5, Remove filter and clean - Pg° 9-t0,
Dust escaping
from cleaner
Headlight not
working
Cleaner is difficult
to push or won't
move forward
PoweredHandTool
8rushroll won't turn
Smoky/burning smell
detected
iili!_i:_i!:!!i_ili>;:_:iih !;iii_!.iii;_i?:i:i=iT::i,:ii:_i_i:!!:ii<:_:i_i;:!:L:i:_,:i_ii:;i{_!:_:iiiii!:i:i:_Y:i:;_i_:;% ii:iii_:i_:!,!i]>i!:i:>iily:ii_i=::]i:j:i:i.iiii:!::!:il::i:ii/::::ii_ii4'fil;:ii:i:i:ii;:;?
7. Carpet height setting is incorrect,, Z, Set carpet height adjustment to appropriate
t, Dirt cup full.
3, Hose not installed correctly,
setting for carpet being cleaned - Pg, 6.
I. Empty dirt cup - Pg, 9,
3. Review hose installation - Pg, 4,
t. Bulb burnt ouL I,Replace bulb - Pg, I0,
l, Carpet height setting is incorrect, t.Set carpet height adjust lever to appropriate
setting for carpet being cleaned - Pg, 6,
2. Blockage in turbine channel. 2, Remove blockage - Pg, 16
4, Low cleaner suction.. 4., Check items under "Cleaner won't pick or low
suction,"
t5
Clearing Blockages
Disconnect cleaner from electrical outlet.
Low suction or pick up may be due to a blockage in the system. Refer to the f0Ilowing steps to check
forblockagescontinuingwith each stepuntiltheblockage isfound:
Fullness of Check Airflow Check Secondary
Dirt Cup Path Filter
Check futlness of dirt
cup; empty if needed
Plug cleaner in and turn ON. Check
for suction at end of hose {A). ]F
there is suction turn cleaner OFF
and unplug,Check connectionat
hose tube {B);remove any blockage,
Check Hose Inlet
Tube
Turn cleaner OFF and
unplug.
If blockage can be seen
in tube {A), remove 5
screws using a Phitlips
screwdriver_
Pull tube from cleaner,
remove blockageo
Reposition tube on back
ofcleaner, replace 5
Screws.
Remove and cleansecondaryfilter
(Fig,4-B,po I0}_Replacefilter.
Checking Under
Bottom Plate
B A
Turn cleanerOFF and
unplug,
Remove bottom plate
(Fig. 4-13) and agitator
brushrol] (Fig. 4-20).
Look into opening {A), in
channels {B) and around
liner (C) and remove any
accumulated debris,
Replaceagitator brushroll
and bottom ptate,
Blockage in Powered Hand Tool
Disconnect powered hand tool from hose.
Remove bottom plate, belt guard and
turbine as described inFigs,4-24, 4-25
and 4-3!.
Remove any blockage from turbine
channel.
Replace belt turbine, brushroll, belt guard
and bottom plate.
t6
Limited One Year Warranty
(Domestic Use}
WHAT THIS WARRANTY COVERS
When used and maintained in normaf household use and in
accordance with the Owners Manual, your HOOVER_ product is
warranted against original defects in material and workmanship
for a full one year from date of purchase [the _Warranty Period")
During the warranty P_riod, Hoover ® will p_ovide labor and parts.
as described in this warranty, at no cost to you, to correct any such
defect in products purchased in the United States. U S Military
Exchanges and Canada
HOW TO MAKE A WARRANTY CLAtM
If this product is not as warranted, take the product to a Hoover
Authorized warranty Service DeaIer along with proof of purchase.
For an automated referral to authorized service outlets, phone:
1-800-944-9200 OR visit Hoover® onIinc: at hoover,cam (US
Customers) or hoover,ca [Canadian Customers} For additional
assistance of information concerning this Wa_'ranty or the
availability of warranty service outlets_ phone 1-BOO-263-B37&
Mon-Fd Barn-7pm EST In Canada, contact Hoover Canada, Toronto:
755 Progress Ave 5catborough, ON MtH 2W7 OR Hoover Canada.
Edmonton: t8129-tlt Ave Edmonton. AB T5W 2P2 . Phone:
1-800-263_6376. Mon-Fri Bam-7pm EST
WHAT THIS WARRANTY DOES NO3" COVER
This warranty does not cover: use of the product in a commercia!
operation (such as maid, janitorial and equipment rentai services),
improper maintenance of the product, damage due to misuse,
acts of God. nature, vandalism or ott_er acts bt_yond the control
of Hoover e. owner's acts or omissions, use outside the country
in which the product was initially purchased and resaIe of the
product by the original owner This warranty does not cover pick
up,d_tivery, transportation or house calls
This warranty does not appIy to products purchased: t outside the
United States, including its territories and possessioas_ 2 outside a
U S Military Exchange or 3 outside Canada, This warranty does not
cover products purchased from a party that is not an authorized
retailer, deal¢r, or distributor of Hoover® products
OTHER IMPORTANT TERMS
This warranty is not transferab]e and may not be assigned, This
warranty shali be governed and construed under the laws of the
state ofOhio The Warranty Period will not be extended by any
r_ptacement or repair performed under this Warranty,
THIS WARRANTY IS THE EXCLUSIVE WARRANTY AND REMEDY
PROVIDED £Y HOOVER® ALL OTHER WARRANTIES, EXPRESSED
OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR PARTICULAR PURPOSE. ARE DISCLAIMED IN
NO EVENTWILL HOOVERBE LIABLE FOR ANY SPECIAL, INDIRECT,
INCIDENTIAL OR CONSENQUENTIAL DAMAGES OF ANY KIND OR
NATURETO OWNEROR ANY PARTYCLAIMING THROUGH OWNER,
WHETHER BASED IN CONTRACT. NEGLIGENCE, TORT DR STRICT
PROOUCTSUABLtLTYORARISING EROMANY CAUSEWHATSOEVER,
Some states do nat allow the _xclusion of consequential damages,
so the above exclusion may not appIy to you, This warranty gives
you specific rights; you may also have others that vary from state
to state
17
anual del Propietario
Instruccionesdeoperaci6n yservicio
www.hoover.com
®
Reviseeste manual antes de hacerfuncionar su Hoover® producto.
_2009 Healthy Gain Investments, Ltd. Todos los derechos reservados_
#17-01-58-058-O0-H301-R1 2109
Gracias por haber elegido
Anote los n_meros completos de modelo y
serie en los espacios provistos.
Modelo
N_mero de sefie
Consejo: Adjunte su recibo de compra a este
Manual del propietario+ Para obtener el servicio
de garantia de su producto HOOVER®puede
requefirse la veriflcacidn de la fecha de compra,
un producto HOOVER+
Asegflrese de llenar y devotver la tar)eta adjunta de registro del producto induida con
su aspiradora (yea la contraportada)+
W
indice
Salvaguardias importantes ............................................................ 3
Ensamblado de la aspiradora ................................................... 4
Contenido de la eaja .............................................................. 4
Cdmo usar la aspiradora .................................................... 5-9
Descripcidn de la aspiradora ............................................... 5
Aecesorios de limpieza ........................................................................... 7-8
Mantenimiento .......................................................... B-13
E1 dep6sito para polvo ........................................................... [I-9
Los Filtros ................................................................ 9+10
La luz ...................................................................... I0
La correa ............................................................ 11
El rodillo de escobillas del agitador ......................................... t2
E1accesorio de mano turboaccionado ..................................... 12-13
El roditlo de escobillas det agitador ................................................ 12-13
La correa del accesorio de mano turboaccionado .......................... t3
Lubricaci6n .......................................................................................... t4
Protector tErmico ........................................................ t4
Servicio autorizado ................................................................. t4
5oluci6n de problemas ............................................................ t5
Eliminaci6n de obstrucciones ............................................................. 16
Garantia .................................................................... 16
Si necesita ayuda:
Visite nuestro sitio web en www,hoover+com. Haga clic en el enlace que permite localizar losvendedores
autorizados Hoover _ para encontrar el vendedor m_s cercano, o marque el t-800-944-9200 para
escuchar un mensaje indicando la direccidn de los vendedores autorizados Hoover ® (sOlo en ee+Uu°) 0
para hablar con un representante de atenciOn al cliente (de 8 am a 7 pm, hora est_ndar del este, de lunes
a viernes),
Pot favor, no devuelva este producto a la tienda.
Estaaspiradora paraalfombras est_disefiadaparausodomOstico_
Noest_disefiadaparausocomercialen una casani paraning_inotto fin comercial,
Hagafundonar la aspkadorapara atfombrassolamenteen elvoltaje especificadoen
Iaplaca de datos, que se encuentra en la parte posterior de la aspiradora, Enchufe la
aspiradora para alfombras en una toma de corriente con una conexi6n a tierra adecuada,
E2
iSamvaguardias importantes!
AI usar un aparato el_ctrico, observe siempre ias precauciones bfisicas, inctuyendo |as siguientes:
LEA TODAS LAS INSTRUCCIONES ANTES DE IJSAR ESTE APARATO
ADVERTENCIA:PaTaT ducirel deincendios, hoquesel t cosolesiones:
No use este aparato en el exterior o en superficies mojadas.
Esnecesaria una supervision estficta cuando cualquier aparato es utilizado pot o cercade los
nifios. No permita que la aspiradora seausada como un juguete ni que funcione sin atenciOn en
ningfln momento.
Mantenga el cabello,Taropa holgada, los dedos de las manos y pies y todas las partes de] cuerpo
a]ejados de las aberturas, de] agitador rotatorio y otras piezas en movimiento'o
o No aspire nada que se este quemando o echando humo, como cigarrillos, cerillos o
cenizas calientes.
No useeste aparato para aspirar materiales inNamables o combustiblescomo gasolina o restos de
madera lijada, ni en _reasdonde pudieran encontrarse presentes,
o Apague siempre este aparato antes de conectar o desconectar la manguera.
o Desenchufe antes de conectar e! accesorio de mano turboaccionado,
o No use la aspiradora sin tener el dep6sito para polvo o los filtros en su lu0aroVacie el depOsitoy
]impie con frecuencia cuando aspire materiales muy finos como talco.
* Tenga especial cuidadoa| ]impiar escaleras,
" No coloque ning_n ob.jeto en |as aberturas_No la usecon ninguna abertura obstmida;
mant_ngala fibre de polvo, peiusa, cabello o cuaIquier cosa que pueda reducir el
flujo de aire.
o Desconecte siempre el cordon de la toma de corriente el_ctrica antes de prestar servicio
a }a aspiradora.
o Desconecte el cordon cuando la aspiradora no est_ en uso_Antes de desenchufarla, apague todos
]os controles..
o No ]a desconecte tirando det cordon. Para desenchuDrla, sujete el enchufe y no el cordon. Nunca
toque el enchufe ni el aparato con las manos mojadas,
o No se recomienda el uso de cordones de extensiOno
* No use et aparato si el cordon o el enchufe estfl dafiado. Si el aparato no est_i funcionando
apropiadamente, se ha dejado caer, ha sido daflado, se ha dejado a la intempefie o se ha dejado
caer en agua, llOvelo a un Centro de ventas y de servicio de Hoover o al Concesionario autofizado
de servicio de garantia de Hoover {DepOsito).
° No tire de _sta ni la transporte por el cordon, ni tampoco use el cordon como mango, no cierre
la puerta sobre el cordon ni tire del mismo alrededor de los bordes agudos ni esquinas.. No pase
el aparato sobre el cordon, Mantenga el cordon alejado de tas
superficies calientes.
° Use la aspiradora solamente para Io que ha sido disefiada segfin se describe en las instrucciones
Use solamente los accesorios recomendados por Hoover; e] uso de otros accesorios puede ser
peligroso,
,5u.jete el enchufe cuando enrolle el cordon en ta bobina, No permita que el enchufe d_ latigazos
cuando enro!te el cordon.
ADVERTENCIA:
* Este producto contiene substancias quimicas conocidas en el estado de California por ser
causantes de c_ncer y presentar riesgos para el sMema reproductor, t.,_vese las manos despu_s de
manipular]o_
° No haga funcionar la aspiradora descalzo ni cuando cake sandalias o zapatos que dejen los
dedos de los pies al descubierto.
, Evite recoger ohjetos duros o afflados con la aspiradora. Estospueden dafiar ]a aspiradora.
iGuarde estas instrucciones!
E3
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34

Hoover UH70085 Owner's manual

Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages