MBM 1703103 Owner's manual

OPERATION MANUAL

MBM 508A

AUTOMATIC FOLDER

1-800-223-2508

www.mbmcorp.com

Rev. 1.01

2

3

Safety Instructions

Definition of Symbols and Notes

In this manual following names and signs stand for possible dangers.

Danger

This Symbol stands for immediate danger threatening the life and

health of persons. Disregarding these instructions may cause severe

damage to health and even serious injuries.

Caution

This symbol stands for an endangering situation that may occur.

Disregarding these instructions may lead to slight injuries or damage to

property.

Danger

Make sure that the machine is electrically grounded. This prevents an electric shock

when there is a leak of electricity.

Use the machine at 230VAC with a frequency of 50/60Hz. A fire may start or the

machine may break down if a higher or lower voltage is used, or if an electric

current with a frequency that is not within the range of frequency stated above.

Do not place any object on this machine. A fire may start or electricity may leak if water

or a foreign object enters inside the machine.

Handle the power cable with care. A fire may start or an electric shock may be

caused if the cable is damaged, broken, or processed, if a heavy object is placed on the

cable, or if the cable is bent forcibly.

Do not pull the power plug out of or put it in the electric outlet using a wet hand.

Otherwise, an electric shock may be caused.

Do not remove the cover of this machine. Otherwise, an electric shock or injury may

be caused.

Do not remodel this machine. Otherwise, a fire may break out or an electric shock may

be caused.

If the machine is used when it is in an abnormal condition, such as generating heat,

emitting smoke, and giving out a strange smell, a fire may break out or an electric

shock may be caused. Turn off the power switch immediately and then pull the power

plug out of the electric outlet. Afterward, consult with your dealer.

If abnormalities such as the power cable generating heat and giving out a strange smell

are found, turn off the power switch immediately and then pull the power plug out of

the electric outlet. Afterward, consult your dealer.

If a foreign object enters into the machine, turn off the power switch first and then pull

the power plug out of the electric outlet. Afterward, consult your dealer.

If thunder approaches, pull the power cable out of the electric outlet to prevent a fire or

breakdown caused by the falling of a thunderbolt.

4

Caution

Do not let hairs, a necktie, or necklace hang above the drive of the machine. Doing so

may cause an injury.

Do not put the machine on an unstable place such as a shaky stand and a slant floor.

Doing so may cause the machine to drop or fall down, causing an injury.

Do not put the machine in a moist or dusty place. Doing so may start a fire or cause

an electric shock.

Be sure to pull out the power cable while holding the plug. If the power plug is pulled

out while holding the cable, a fire may break out or an electric shock may be caused.

Be sure to pull the power plug out of the electric outlet first when moving this machine.

Otherwise, the cable may be damaged, causing a fire or an electric shock.

Be sure to pull the power plug out of the electric outlet for safety purposes when this

machine is not in use for prolonged period such as consecutive holidays or for other

reasons.

① Moving Parts

② Warning Label

①

②

Warming

5

Introduction

Please read this Operation Manual carefully before using this machine. Store the Operation Manual in a

safe place so that it can be easily retrieved and referred to whenever required.

Since the specifications of this product are subject to change for the purpose of further improvement,

the descriptions in the Operation Manual may be different from unit to unit even for the same model.

Be sure not to refer this manual for one of a different model. Use this manual only for originally

delivered model. Some components are omitted in the illustrations in this manual.

6

Content

1. Precautions on Installation

1-1 Installation location .............................................................................................. 7

1-2 Precautions in moving in ...................................................................................... 7

1-3 Check the content and quantity of accessories .................................................. 8

2. Part Name

2-1 Appearance ......................................................................................................... 9

2.2 Control panel .................................................................................................... 10

3. Matters That Require Particular Attention

3-1 Definition of terms

3-1-1 Explanation of mark .................................................................................. 10

3-1-2 Term/Fold type description ....................................................................... 10

3-2 Characteristics and intended purpose of use .................................................. 11

3-3 When not in use ................................................................................................. 11

3-4 Precautions for use ............................................................................................ 11

4. Preparation

.......................................................................................................... 12

5. How to Use

5-1 Standard Folding of Standard-size Paper ........................................................ 14

5-2 To manually input paper length ........................................................................ 16

5-3 Non-standard Folding ...................................................................................... 18

5-4 Cross Folding .................................................................................................... 20

5-5 How to fold art paper/coated paper

5-5-1 Replace with the separator for coated paper. ............................................... 21

5-5-2 Pressure adjustment for paper feed and paper separator ............................. 22

5-6 Adjustment

5-6-1 Slant adjustment .......................................................................................... 23

5-6-2 Fine adjustment of fold position .................................................................. 24

5-6-3 Adjustment of paper ejection roller position............................................... 27

5-7 Memorization/deletion of fold position of standard-size paper

5-7-1 Memorization of finely-adjusted fold position ......................................... 28

5-7-2 Deletion of individual memory of fine adjustment ................................... 29

7

5-8

Memorization/deletion of fold position of non-standard fold and non-standard-size paper

5-8-1 Memorization of fold position .................................................................. 30

5-8-2 Calling up fold pattern memory ................................................................ 31

5-8-3 Deletion of entire fold pattern memory ..................................................... 32

5-9 Counter setting

5-9-1 Addition mode .......................................................................................... 33

5-9-2 Subtraction mode ...................................................................................... 34

5-9-3 Interval mode ............................................................................................ 35

5-10 Speed adjustment ............................................................................................. 36

5-11 Double feed detection function

5-11-1 What is double feed detection ................................................................... 37

5-11-2 Activation of double feed detection .......................................................... 37

5-11-3 Use of double feed detection ..................................................................... 38

5-11-4

When the machine stops based on double feed detection error (E-52)

........................... 38

6. Maintenance Service, Inspection, Expendables

6-1 Cautions for maintenance service and inspection ......................................... 39

6-2 Usual maintenance service .............................................................................. 39

6-3 Expendable supplies ......................................................................................... 39

6-4 Removal and installation, and cleaning of folder roller ............................... 40

6-5

Cleaning of the paper feed, double feed detection, paper ejection photo sensors

................. 41

6-6

Removal and installation of paper separator, paper feed rubber roller, brake rubber

.............

42

7. Trouble shooting and correction

7-1 Error display

7-1-1 Error display screen .................................................................................. 43

7-1-2 List of Error Codes .................................................................................... 44

7-2 Troubleshooting ................................................................................................ 45

8. Relocation or Disposal

8-1 Relocation

8-1-1 Removal of the machine from its present location ................................... 47

8-1-2 Transport ................................................................................................... 47

8-1-3 Installation ................................................................................................. 47

8-2 Disposal ............................................................................................................. 47

9. Specifications ...................................................................................................... 48

8

1. Precautions on Installation

1-1 : Installation location

Install this product where the following conditions can be fulfilled.

• Do not install it in a place exposed to direct sunlight.

• Avoid a location near a window.

• Do not install it in a dusty place or a place of high humidity.

• Do not install it in a place exposed to a direct wind or a location near a heating equipment.

• Install it on a sturdy and horizontally-located flat stand or table.

1-2 : Precautions in moving in

・Handle with care and do not subject the unit to shock or strong vibration.

・Ensure that the machine is carried by two persons wearing protective gloves, holding the

four corners of the base firmly

.

9

1-3 : Check the content and quantity of accessories

Check accessories immediately upon unpacking.

Should there be anything short, contact your distributor.

Also, fill out the warranty documents.

Accessories Qty Illustration

Folding Table 1

1

Folding Table 2

1

Power cable

1

Auxiliary paper guide

(right and left)

One(1) each

Operation Manual

1

Handy Manual

(1 page/A3 size)

1

10

2. Part Name

2-1 : Appearance

No. Name Function No. Name Function

1 Auxiliary table For supporting larger paper 11 Paper feed table For loading paper

2 Inlet For connecting the power

cable

12 Paper guide For prevent slant paper feeding

3 Paper ejection roller Arranges and ejects folded

paper

13 Paper feed pressure

lever

For adjusting paper feed

pressure

4 Paper ejection table For stacking folded paper 14 Separator pressure

lever

For adjusting separator pressure

5 Safety cover The machine stops when this

cover is opened.

15 Left side cover For protecting mechanical parts

6 Control panel For setting operation of

machine

16 Folding table 1 For performing the first fold

7 Right side cover For protecting against

mechanical/electrical parts

17 Folder roller setting

lever

For removing and setting the

folder roller

8 Breaker For protecting against

overcurrent

18 Folding table 2 For performing the second fold

9 Power switch For turning on/off the power

10 Paper feed roller Feeds one sheet of paper

11

2-2 : Control panel

Number Name Function

A Color LCD Touch panel To enter operation command and display

B “TEST” key To perform test folding (two sheet without count)

C

“

START/STOP” key

To start and stop the machine

3. Matters That Require Particular Attention

3-1 : Definition of terms

3-1-1 : Explanation of mark

Caution

！

........... Matters that require attention

Hint

！

................... Matters that are good to know

3-1-2 : Term/Fold type description

Term Description

Jam Paper is stuck inside the machine.

Double feed Two or more sheets of paper are fed together.

Slip Paper is not fed due to slippage.

Fan out Separate stuck sheets of paper by letting air in between them

Chart

Fold type Single fold

Double

parallel fold

Fold-out fold Letter fold Zigzag fold Gate fold

The shaded parts in the illustrations show the upper side of the paper placed on the paper feed table.

12

3-2 : Characteristics and intended purpose of use

▪ Easy-to-read LCD color touch panel.

▪ High-speed paper folding.

▪ Automatic paper size detection, fold position setting, paper feed table adjustment (up-down),

and paper ejection roller movement.

▪ For non-standard-paper or non-standard-fold, simply input paper length and fold type to

automatically calculate fold position – no time-consuming manual calculation required.

▪ Memorizes up to 20 non-standard fold patterns.

Three parameters – fold position, speed, and paper ejection roller position – can be memorized.

▪ Interval mode

▪ Double feed detection function

▪ Cross folding

3-3 : When not in use

▪ Remove the power plug from the power outlet.

▪ Place the machine cover over the machine.

3-4 : Precautions for use

▪ Hold the center of the roller cover when opening or closing to prevent any danger of getting

caught in the roller.

▪ Always conduct a test folding to check the fold position for particularly important documents.

▪ Regardless of the reasons, we will not be responsible or liable for folding misalignment and

damage.

13

4. Preparation

1. Install fold table 1 and 2 at the machine.

2 .Insert the plug into the connector.

14

Pull out and extend the paper ejection table.

Then, lift up and set flat the auxiliary table.

Insert the power cable into the outlet.

(The shape of plug may differ from the one shown

in the illustration.)

Caution!

Be sure to unwind folded power cable before

use.

Do not use any power cable other than

provided as an accessory.

Be sure to ground the earth wire of the power

cable.

When the power switch is on, the touch panel

lights and the machine is ready to operation.

Danger

Do not insert or remove the power plug with a wet hand.

It may cause an electric shock.

Do not insert the ground (earth) wire of the power cable into the outlet or bring it into

contact with the outlet. It may cause a fire or electric shock.

15

5. How to Use

5-1 : Standard Folding of Standard-size Paper

[1] Set the standard –size-paper.

[2] Loosen the paper guide setscrew and set the paper

guide to fit the width of the paper.

[3] Stack the paper on the paper feed table after neatly

arranging it.

[4] Make the paper guide closely contact the paper and

tighten the paper guide setscrew.

[5] Select the fold type.

Select from among the six fold types (Single,

Double, parallel, Fold-out, Letter, Zigzag, Gate).

Press the desired fold type key.

Caution!

Be sure to ensure that ink has dried completely on printed materials. In case of immediately

after printed documents, they may cause jamming, double feeding, paper slippage or wrinkles.

16

[7] Test folding

Press the “TEST” key, and one sheet will be folded.

(The counter display will remain to display [0].

Check the folding result with the folded paper.

Hint!

▪ Stains on the roller

▪ The paper guide is set askew, or it is not in close contact with the paper.

▪ The paper feed table is set askew.

▪ The paper is cut at a slant.

→ Refer to “5 - 6 Adjustment” on pages 23 to 27.

[8] Continuous folding

Press the “START/STOP” key, and the paper feed

table will move up and the machine will

continuously fold the paper.

When the “START/STOP” key is pressed while the

machine is in operation, the machine will stop the

operation, but the addition on the counter will

continue.

If you wish to fold only the number of sheets

desired, refer to “5-9-2 Subtraction Mode” on page

34.

If paper is not ejected smoothly, refer to “5-6-3

Adjustment of Paper Ejection Roller Position” on

page 27.

17

5-2 : To manually input paper length

[1] Measure the length of paper in the direction of feeding

paper.

[2] Press the “Non-standard Fold” key

[3] Press the “Input Paper Length” key.

[4] Input the length of paper using numerical keys and

press the “Enter” key.

18

[5] Select the desired fold type from among the six fold ty

p

keys.

[6] Press the “TEST” key to perform test folding.

If test folding is satisfactory, proceed to step [7].

If it is not satisfactory, adjust folding misalignment.

= > Refer to “5.6 Adjustment” on pages 23 to 27.

[7] Press the “START/STOP” key to start continuous folding

.

19

5-3 : Non-standard Fold

▪ Automatic settings cannot be used for non-standard fold. Individual setting of paper size and

specifications is required.

▪ It can be set for both standard-size paper and non-standard paper based on the following procedure.

[1] Using the standard-size or non-standard-size paper you want to fold, create a sample by

folding the paper manually.

[2] Press the “Non-standard Fold” key

[3] Select the key of the fold type that is the nearest to the

intended folding.

[4] Press the “a” key , and “b” key.

 In the case of single fold, there is no screen for inputting

the length of “a” but only the length of “b” should be

input.

20

[5] Input the length of “a” using numerical keys and

press the “Enter” key.

[6] Input the length of “b” using numerical keys and press

the “Enter” button.

[7] Press the “TEST” key to perform test folding.

If test folding is satisfactory, proceed to step [8].

If it is not satisfactory, adjust folding misalignment.

= > Refer to “5.6 Adjustment” on pages 23 to 27.

[8] Press the “START/STOP” key to start continuous

folding.

Page is loading ...

MBM 1703103 Owner's manual

This manual is also suitable for

MBM 1703103 Owner's manual

Related papers

Other documents