Brandt 60EC Owner's manual

Brand: Brandt

Model: 60EC

Type: Owner's manual

Groupe Brandt 60EC is a vitroceramic hob that offers precise heat control and a range of features to enhance your cooking experience. The large 2.1 kW hotplate is ideal for boiling water or searing meats, while the smaller 1.2 kW hotplate is perfect for simmering sauces or melting chocolate. The hob's residual heat warning lights indicate when the hotplates are still hot to the touch, preventing burns. Groupe Brandt 60EC is also easy to clean, with a smooth vitroceramic surface that resists scratches and stains.

INSTRUCTIONS MANUAL

FOR VITROCERAMIC HOBS

ESSENTIALS

C60T124A8 15/7/03 07:01 Página 1

BET WITH US ON ECOLOGY. RECYCLE THE PACKAGING.

We contribute in the defence of the Environment.Thus, our

packagins:

• Are 100% recyclable.

• Contain the smaller quantity of parts and possible material

to facilitate thus the recycling.

C60T124A8 15/7/03 07:01 Página 2

CONTENTS

General description

........................................................... 1

Using the controls...................................................................2

Using pans..................................................................................3

Cleaning ................................................................................... 4

Connection Schema

.............................................................

Installation

............................................................................ 6,7

WARNING

Pot.max:

Type:

Voltage:

• Repair of any fault in your hob must be carried out only by an

Authorized Repair Service, otherwise the guarantee is not valid.

•Technical details and identification of the appliance are shown on

the specifications plate.

Consult this plate before procceding with electrical connection.

• Electrical connection must be carried out by a specialist, familiar

with the laws and official regulations recognized in each country.

Fill in the data table you will find below, with the data appearing on

the specifications plate, sticked on the hob.

Trade mark:

C60T124A8 15/7/03 07:01 Página 3

GENERAL DESCRIPTION

123456

REMARKS

LARGE HOTPLATE

(2,1 KW)

MEDIUM HOTPLATE

(1,7 KW)

SMALL HOTPLATE

(1,2 KW)

CONTROL SETTING

TYPE OF HOTPLATE

DIFFERENT

ELEMENTS COME

INTO PLAY

DEPENDING ON

SETTING

220 W 350 W 550 W 950 W 1.500 W 2.100 W

180 W 280 W 450 W 750 W 1.200 W 1.700 W

130 W 200 W 325 W 500 W 825 W 1.200 W

C60T124A8 15/7/03 07:01 Página 4

USING THE CONTROLS

Make sure that you turn on the right

knob for the heating zone you wish to

use.

As soon as a hotplate gets warm, the

corresponding residual heat warning

light will come on. After switching off,

the light will remain on until the

hotplate cools (about 30 minutes).

Turn the selector to the desired

seting: Setting 1: MINIMUM.

The ON light will come on.

C60T124A8 15/7/03 07:01 Página 5

USING PANS

Most stainless steel, enamel, iron,

ceramic and copper pans can be used

on vitroceramic hobs.

Aluminium pans are not recommended

as they may stain the vitreous surface,

unless they have stainless-steel covered

bottoms.

Hotplates should not be switched on

without a pan on top. The base of the

pan should be flat and dry. Pans that

have been used on gas cookers are not

normally flat enough and absorb heat

badly.

Make sure that the diameter of the pan

is at least that of the hotplate.

Avoid scarping pans over the

vitroceramic surface, as it may become

scratched. Lift always the pan.

Never use tinfoil or plastic containers.

They will melt and fuse permanently

with the vitroceramic surface.

SATINLESS STEEL

ENAMEL

CERAMIC

COPPER

ALUMÍNIUM ALUMÍNIUM

SATINLESS STEEL

YES

C60T124A8 15/7/03 07:01 Página 6

IMPORTANT: If the vitroceramic surface breaks or you notice cracks in it, disconnect the hob.

Call your Repair Service.

CLEANING

Clean the vitroceramic surface

frequently, when it is cool. Never use

abrasive products or pads. Clean

with a damp cloth and soapy water.

Never use a steam cleaner.

Once a week, clean thoroughly with

specific products that preserve and

protect vitroceramic hobs (Sample in

accessory bag). Scrape off hard stuck

dirt with the scraper (Included in

accessory bag).

The manufacturer recommends

VITRO-CLEN for cleaning and

conserving your vitroceramic hob.

If sugar (or sugary matter) or plastic

is accidentally burnt on the hob,

remove it at once with the scraper

while it’s still hot. Otherwise they may

leave a pemanent mark.

Do not use the hob as a work surface.

Be particularly careful with dirt like

soil or dust from vegetables, cleaning

powders, etc. which may scratch the

surface when pans are slid over it.

INMEDIATELY

C60T124A8 15/7/03 07:01 Página 7

CONNECTION SCHEMA

Hob will make the connection according to the adjacent drawings. (The

cable must support temperatures of up to 120ºC).

The hotplate must be connected to the mainstrean with a plug that meets the

EEC 7 publication or with a multi-pole switch with a distance between the

open contacts of at least 3mm.

Total power

Hotplate: 60 cms., 6,3kW

This device conforms to European directives 73/23/CEE and 89/336/CEE

60 cms 220...240V~ 27,5 A 32 A 220...240V~ 14 A 16 A

Voltage Int.nominal Protection

by phases

Voltage Int.nominal Protection

by fases

PLATE

Three phase

60 cms 380...400V~ 11 A 12 A 380...400V~ 16 A 20 A

Voltage Int.nominal Protection

by phases

Voltage Int.nominal Protection

by phases

PLATE

Three phase

C60T124A8 15/7/03 07:01 Página 8

INSTALLATION

Place the hob face down on a

table. Remove the backing paper

and affix the sealing gasket all

round the perimeter. (fig.1)

When the plate comes without

frame, first stick on the shaped

strips as shown on the drawing

and then stick on the straight

strips adjusting them with the

previous ones. (fig.2).

Cut out a piece of the worktop following

the instructions on the template that

comes with the hob.

“X” type apparatus for degree of fire

protection.

Minimum distance between hole and

wall 100 m/m.

NOTE: DO NOT USE NON-REMOVABLE ELEMENTS WITH SILICONE.

fig.1

fig.2

C60T124A8 15/7/03 07:01 Página 9

INSTALLATION

Place the hob alongside the cavity in

the worktop and connect the power

cable to the electrical socket.

IMPORTANT: Carry out connection

with the power disconnected. There

must be a good grounding connection

and a switch must be provided in an

accessible place to isolate all phases,

with at least 3mm. clearance between

contacts. The manufacturer will not accept

responsability for installations carried out other

than as directed here.

The hob installation should be performed by a

technician certificated by the manufacturer.

Next insert the hob in the worktop

cavity, pressing down firmly to ensure a

good seal.

NOTE: This equipment complies with standard 82/499/CE on radio interferences.

Fix the 4 clamps underneath the hob to

the 4 corners of the cavity.

(Clamps, brackets and nuts are

supplied in acessory bag).

C60T124A8 15/7/03 07:01 Página 10

07-03

C60T124A8

Printer on recycled paper

Your 1

Year Guarantee

Yo ur appliance carries a 12 months parts and labour warranty. To fulfil the

conditions of your guarantee, the appliance must be correctly installed and

operated, in accordance with the instructions, and be only used for normal

domestic purposes.

Please note that the guarantee, and service availability, only apply to the

United Kingdom.

Customer Service

In case of difficulty please call the Customer Service Helpline on

01245 321111

Please ensure you have the model and serial number to hand when calling

customer service.

C60T124A8 15/7/03 07:01 Página 12

Brandt 60EC Owner's manual

Brandt 60EC Owner's manual

Brandt 60EC Owner's manual

Related papers

Other documents