2. Home
  3. Domestic appliances
  4. Climate control
  5. Household fans
  6. Westinghouse
  7. 7200600
7200600

Westinghouse 7200600, 52-inch, 7200500 User manual

  • Hello! I am an AI chatbot trained to assist you with the Westinghouse 7200600 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Page is loading ...
2
ETL-ES-Tulsa-R-WH14
1. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards (ANSI/NFPA 70), including fire-rated construction.
2. Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
3. After making the wire connections, gently push connections into outlet box with wire nuts pointing up. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on
one side of the outlet box and ungrounded conductor on the other side of the outlet box.
4. Before you begin installing the fan, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
5. Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
6. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
7. Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to the trailing edge of the blade.
8. To reduce the risk of fire, electric shock, or personal injury, this fan must be mounted to an outlet box marked suitable for fan support, and use the mounting screws provided with the outlet box. (Mounting must
support at least 35 lbs.)
9. WARNING! Do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert foreign object between rotating blades.
10. Attach the mounting bracket using only the hardware supplied with the outlet box. Fan is only to be mounted to an outlet box marked “Acceptable for Fan Support”.
11. WARNING! To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
12. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
13. NEVER place a switch where it can be reached from a tub or shower.
14. The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment manufacturer’s guideline safety standards such as those
published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
15. Before servicing or cleaning unit, switch power off at service panel and lock service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be
locked, securely fasten a prominent warning device, such as a tag, to the service panel.
16. All set screws must be checked and re-tightened where necessary before installation.
17. The appliance is not intended for use by young children or infirmed persons without supervision. Young children should be supervised to ensure that they do not play with the appliance.
TOOLS REQUIRED
Phillips Screwdriver Wire Cutters Pliers Step Ladder
SAFETY TIPS
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED 'ACCEPTABLE FOR FAN SUPPORT OF 15.9 KG (35 LBS) OR LESS' AND
USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX AND/OR SUPPORT DIRECTLY FROM BUILDING STRUCTURE. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF
LUMINARIES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT.
Page is loading ...
4
ETL-ES-Tulsa-R-WH14
DOWNROD
INSTALLATION
INSTALACIÓN CON
VARILLA VERTICAL
For normal ceilings
Para techo normales
SLOPED CEILING
INSTALLATION
INSTALACIÓN PARA
TECHO INCLINADOS
May require a longer downrod
(sold separately)
Podría requerir una varilla vertical más larga
(se vende por separado)
FLUSH MOUNT INSTALLATION
INSTALACIÓN AL RAS
For low ceilings
Para techo bajos
FEATURES
CARACTERÍSTICAS
Note: For pitched ceiling installation, please refer to westinghouselighting.com for specially designed canopy kit options.
Nota: Para instalación en techo inclinados, visite westinghouselighting.com para obtener información sobre juegos de dosel
especialmente diseñados.
5
ETL-ES-Tulsa-R-WH14
COMBO-BLADE
Combo-Blades feature two high quality finishes on one blade. Select the one that best complements
your decor, or change the style with just a flip of the blade.
NOTE: Combo-Blade finishes vary, depending upon model.
ASPAS DE DOBLE CARA
Las aspas del rotor de doble cara presentan dos superficies con un acabado de alta calidad. Invirtiendo
las aspas Ud. puede producir un efecto decorativo adaptado a su ambiente o crear una decoración
completamente nueva.
Observación: las superficies de las aspas de doble cara son distintas dependiendo del modelo.
FEATURES
CARACTERÍSTICAS
Page is loading ...
7
ETL-ES-Tulsa-R-WH14
3
Remove the screws and star washers from the two mating holes (2) on the canopy. Loosen (do not remove) the screws in the mating slots (1) on the canopy.
Rotate the mounting bracket and remove from the canopy.
Quite los tornillos y las dos arandelas en estrella de los dos agujeros coincidentes (2) del dosel. Afloje (no quite) los tornillos de las ranuras coincidentes (1) del dosel.
Gire el soporte de montaje y sepárelo del dosel..
MOUNTING BRACKET INSTALLATION
INSTALACIÓN CON SOPORTE DE MONTAJE
1
2
8
ETL-ES-Tulsa-R-WH14
MOUNTING BRACKET INSTALLATION
INSTALACIÓN CON SOPORTE
DE MONTAJE
Install mounting bracket to outlet box in ceiling using the screws and washers
provided with the outlet box.
Instale el soporte de montaje a la caja de embutir del techo con la tornillería
suministrada con la caja de embutir.
4
5
MOUNTING OPTIONS
OPCIONES DE MONTAJE
Choose a MOUNTING OPTION
Elija una OPCIÓN DE MONTAJE
FLUSH MOUNT OPTION
If flush mount option is selected, proceed to page 9, step 6.
OPCIÓN DE INSTALACIÓN AL TECHO
Si elige la opción de montaje al techo,
proceda a la página 9, paso 6.
NORMAL DOWNROD OPTION
If installing downrod supplied with fan, proceed to page 10, step 8.
OPCIÓN CON VARILLA VERTICAL PARA TECHO NORMAL
Si instala la varilla vertical incluida con el ventilador,
proceda a la página 10, paso 8.
EXTENDED DOWNROD OPTION
If installing with longer downrod than supplied with fan, proceed to page 12, step 11.
OPCIÓN CON VARILLA VERTICAL MÁS LARGA
Si instala una varilla vertical más larga de la que se incluye con el
ventilador, proceda a la página 12, paso 11.
9
ETL-ES-Tulsa-R-WH14
FLUSH MOUNT OPTION
OPCIÓN DE INSTALACIÓN AL TECHO
6
Guide motor wires through the base of the canopy as shown and attach canopy
directly to top of motor housing with flush mount screws and lock washers
provided. Tighten screws securely.
Deslice los cables del motor a través de la base del dosel como se indica y fije el
dosel directamente sobre el alojamiento del motor con los tornillos de montaje al
ras y las arandelas de presión incluidas. Apriete los tornillos asegurándolos.
For flush mount option, raise fan assembly and place onto hook (1) from mount-
ing bracket into a closed hole on the canopy. This will allow for hands free wiring.
PROCEED DIRECTLY TO PAGE 15 FOR WIRING OPTIONS.
Para la opción de montaje al techo, levante el montaje del ventilador,
colóquelo sobre el gancho (1) del soporte de montaje y cuélguelo en uno
de los agujeros cerrados del dosel. De este modo, tendrá las dos manos
libres para hacer el cableado. PARA LAS OPCIONES DE CABLEADO,
PROCEDA DIRECTAMENTE A LA PÁG. 15
1
1
7
10
ETL-ES-Tulsa-R-WH14
9
Place downrod assembly (1) into canopy (2) and coupling cover (3). Feed motor wires
though the downrod assembly (1).
Coloque el conjunto de la varilla vertical (1) dentro del dosel (2) y la cubierta del acopla-
miento (3). Pase los cables del motor a través del conjunto de la varilla vertical (1).
2
1
3
Quite el pasador tipo prensa (1) desde el pasador transversal (2) de la vara (3).
8
Remove clamp pin (1) and cross pin (2) from downrod (3).
1
2
3
NORMAL DOWNROD OPTION
OPCIÓN CON VARILLA VERTICAL PARA TECHO NORMAL
Page is loading ...
12
ETL-ES-Tulsa-R-WH14
11
Loosen (1) from downrod (2) by removing set screw (3).
Afloje la bola de la varilla vertical (1) de la varilla vertical (2) quitando
el tornillo (3).
2
3
1
EXTENDED DOWNROD OPTION
OPCIÓN CON VARILLA VERTICAL MÁS LARGA
12
Slide downrod ball (1) off of downrod and remove pin (2).
Deslice la bola de la varilla vertical (1) hasta separarla de la varilla vertical y
quite el pasador (2).
2
1
Page is loading ...
14
ETL-ES-Tulsa-R-WH14
MOUNTING
MONTAJE
15
With bracket holding fan assembly, make electrical connections using the following
step for wiring instructions.
Con el soporte de montaje sujetando el conjunto del ventilador, haga las conexiones
eléctricas de acuerdo a las siguientes instrucciones de cableado.
14
Carefully lift fan assembly onto mounting bracket. Rotate fan until notch
on downrod ball (1) engages the ridge on the mounting bracket (2). This
will allow for hands free wiring.
Levante con cuidado el conjunto del ventilador hasta el soporte de montaje.
Gire el ventilador hasta que la muesca de la bola de la varilla vertical (1)
enganche sobre la saliente del soporte de montaje (2). De este modo, tendrá
las dos manos libres para hacer el cableado.
15
ETL-ES-Tulsa-R-WH14
WIRING OPTIONS
OPCIÓN DE CABLEADO
17
*Connect blue wire only if attaching light kit with fan.
Follow diagram above to make wiring connections for wall control operation.
16
*Connect blue wire only if attaching light kit with fan.
Follow diagram above to make wiring connections for fan pull chain control.
PULL CHAIN WIRING OPTION
WALL CONTROL WIRING OPTION
Siga las instrucciones del diagrama anterior para hacer las conexiones de
cableado para el ventilador con control de pared.
Siga las instrucciones del diagrama anterior para hacer las conexiones de
cableado para el ventilador controlado con cadenilla de tiro.
OPCIÓN DE CABLEADO PARA CADENILLA DE TIRO
OPCIÓN DE CABLEADO PARA CONTROL DE PARED
16
ETL-ES-Tulsa-R-WH14
Secure To ceiling
ASegure el venTilAdor Al TecHo
1
3
2
The canopy has two mating slots (1) and two mating holes (2). Position both slots on canopy directly under and in line with two screws in the mounting bracket (3). Lift the
canopy, allowing the two screws to slide into the mating slots. Rotate the canopy clockwise until both screws from the mounting bracket drop into the slot recesses. Tighten
screws securely. Install two screws and lock washers into the mating holes of the canopy and tighten to secure the canopy to the mounting bracket.
El dosel tiene dos ranuras coincidentes (1) y dos agujeros coincidentes (2). Coloque ambas ranuras del dosel directamente abajo y en línea con los dos tornillos del soporte
de montaje (3). Eleve el dosel, permitiendo que los dos tornillos se deslicen dentro de las ranuras. Gire el dosel en sentido horario hasta que ambos tornillos del soporte de
montaje caigan adentro de las ranuras. Apriete los tornillos asegurándolos. Instale los dos tornillos y las arandelas de presión en estrella en los orificios coincidentes del
dosel y ajústelos para asegurar el dosel al soporte de montaje.
18
1
3
2
For flush mount fans, carefully lift fan from the mounting bracket, making sure not to break any wire connections.
For downrod fans, slide the canopy up to the mounting bracket.
Para ventiladores de instalación al techo, levante con cuidado el ventilador del soporte de montaje asegurándose de que no interrumpa ninguna conexión de los cables.
Para ventiladores con varilla vertical, deslice el dosel hacia arriba hasta el soporte de montaje.
Page is loading ...
18
ETL-ES-Tulsa-R-WH14
ligHT fixTure inSTAllATion
inSTAlAción del ArTefAcTo luminoSo
21
Find the wire plugs from the light kit and from the motor and slide together. Connect the blue wire from the switch housing, to the black wire from the light kit, and the
white wire from the switch housing to the white wire from the light kit. Attach light kit to the switch housing using three small screws provided.
Identifique los conectores para cables de salida del artefacto luminoso y del motor y deslícelos para unirlos. Conecte el cable azul del alojamiento del interruptor al cable
negro del artefacto luminoso y el cable blanco del alojamiento del interruptor al cable blanco del artefacto luminoso. Conecte el artefacto luminoso al alojamiento del
interruptor con los tres tornillos pequeños incluidos.
19
ETL-ES-Tulsa-R-WH14
ligHT fixTure inSTAllATion
inSTAlAción del ArTefAcTo luminoSo
22
Unscrew and remove the finial (1), decorative cap (2), nut (3), and rubber/metal washer (4) from the bottom of the light kit. Install the bulbs (included).
Desenrosque y quite el florón (1), la tapa decorativa (2), la tuerca (3) y la arandela de caucho/metal (4) de la parte inferior del juego de luces. Instale las bombillas de luz
(incluidas).
4
3
2
1
20
ETL-ES-Tulsa-R-WH14
23
5
4
3
2
1
Install the glass (5) onto the light kit and tighten the washer (4) and nut (3) onto the bottom of glass. Make sure the ceiling fan pull chain is threaded through the side hole
in the bottom of the glass. Place decorative cap (2) over the bottom of glass and secure by tightening decorative finial (1).
Note: (6) Make sure the side hole on the decorative cap lines up with the side hole on the bottom of the glass so that the fan pull chain operates smoothly.
Instale la pantalla de vidrio (5) en el juego de luces y ajuste la arandela (4) y la tuerca (3) en la parte inferior de la pantalla. Asegúrese de que la cadenilla de tiro del ventila-
dor de techo pasa por el agujero lateral de la parte inferior de la pantalla. Coloque la tapa decorativa (2) sobre la parte inferior de la pantalla de vidrio y asegúrela ajustando
el florón decorativo (1).
Nota: (6) Asegúrese de que el agujero lateral de la tapa decorativa esté alineado con el agujero lateral de la parte inferior de la pantalla de vidrio para que la cadenilla de tiro
del ventilador de techo funcione sin inconvenientes.
6
Page is loading ...
22
ETL-ES-Tulsa-R-WH14
OPERATION AND MAINTENANCE
Operation
Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off.
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on.
The slide switch controls direction, forward or reverse.
Warm weather/down position - (Forward) Fan turns counterclockwise direction. A downward air flow creates a cooling effect as shown in illustration A.
This allows you to set your air conditioner on a higher temperature setting without affecting your comfort.
Cool weather/up position - (Reverse) Fan turns clockwise direction. An upward airflow moves warm air off the ceiling area as shown in illustration B.
This allows you to set your heating unit on a lower setting without affecting your comfort.
NOTE: Turn off and wait for fan to stop before changing the setting of the forward/reverse slide switch.
Maintenance
1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year.
Make sure they are secure.
2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning.
This could damage the motor, or the wood, or possibly cause electrical shock.
3. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer coating to minimize discoloration or tarnishing.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.
Page is loading ...
24
ETL-ES-Tulsa-R-WH14
TROUBLESHOOTING GUIDE
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these
installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be
remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself.
TROUBLE
1. If fan does not start:
2. If fan sounds noisy:
3. If fan wobbles:
4. If light does not work:
SUGGESTED REMEDY
1. Check main and branch circuit fuses or circuit breakers.
2. Check wire connections as performed in step #16 or #17 of installation. CAUTION: Make sure main power is turned off.
3. Make sure forward/reverse switch is firmly in up or down position. Fan will not operate when switch is in the middle.
4. If the fan still will not start, contact a qualified electrician. Do not attempt to troubleshoot internal electrical connections yourself.
1. Check to make sure all screws in motor housing are snug (not over tightened).
2. Check to make sure the screws which attach the fan blade holder to the motor are tight.
3. Some fan motors are sensitive to signals from Solid State variable speed controls. DO NOT USE a Solid State variable speed control.
4. Allow “break-in” period of 24 hours. Most noises associated with a new fan will disappear after this period.
All blades are weighed and grouped by weight. Natural woods vary in density which could cause the fan to wobble even though all blades are weight-matched. The following procedures should
eliminate most of the wobble. Check for wobble after each step.
1. Check that all blades are screwed firmly into blade holders.
2. Check that all blade holders are tightened securely to motor.
3. Make sure that canopy and mounting bracket are tightened securely to ceiling joist.
4. If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and possibly result in smoother operation.
1. Check for faulty light bulbs.
2. Check to see that the wire connections in the switch housing are connected.
3. If light kit will still not operate, contact a qualified electrician for assistance.
Page is loading ...
26
ETL-ES-Tulsa-R-WH14
PARTS LIST
LISTA DE REPUESTOS
# Description
1. . . . . . . . . . . . . . . . . . . . . . Mounting Bracket
2. . . . . . . . . . . . . . . . . . . . . . Blade Bracket
3. . . . . . . . . . . . . . . . . . . . . . Blade
4. . . . . . . . . . . . . . . . . . . . . . Glass
5. . . . . . . . . . . . . . . . . . . . . . Fan Speed Switch
6. . . . . . . . . . . . . . . . . . . . . . Light Control Switch
7. . . . . . . . . . . . . . . . . . . . . . Capacitor
8. . . . . . . . . . . . . . . . . . . . . . Hardware Pack
No. Descripción
1. . . . . . . . . . . . . . . . . . . . . .Soporte de montaje
2. . . . . . . . . . . . . . . . . . . . . .Soporte para aleta
3. . . . . . . . . . . . . . . . . . . . . .Aleta
4. . . . . . . . . . . . . . . . . . . . . .Pantalla de vidrio
5. . . . . . . . . . . . . . . . . . . . . .Interruptor de control de
. . . . . . . . . . . . . . . . . . . . . . .velocidad para ventilador
6. . . . . . . . . . . . . . . . . . . . . .Interruptor de control de luz
7. . . . . . . . . . . . . . . . . . . . . .Condensador
8. . . . . . . . . . . . . . . . . . . . . .Tornillería
1
3
4
8
7
5
6
2
Page is loading ...
28
ETL-ES-Tulsa-R-WH14
Westinghouse Lighting, Philadelphia, PA 19154-1029, U.S.A.
www.westinghouselighting.com
, WESTINGHOUSE, and INNOVATION YOU CAN BE SURE OF
are trademarks of Westinghouse Electric Corporation.
Used under license by Westinghouse Lighting
All rights reserved.
Made in China
/