Sparky M 850 HD User manual

Brand: Sparky

Model: M 850 HD

Category: Power tools

Type: User manual

This manual is also suitable for

www.sparky.eu

1 – 11

ANGLE GRINDER

Original instructions

25 – 37

MEULEUSE ANGULAIRE

Notice originale

87 – 100

УГЛОШЛИФОВАЛЬНАЯ МАШИНА

Оригинальная инструкция по эксплуатации

12 – 24

WINKELSCHLEIFER

Originalbetriebsanleitung

Оригінальна інструкція з експлуатації

101 – 113

КУТОШЛІФУВАЛЬНА МАШИНА

75 – 86

SZLIFIERKA KĄTOWA

Oryginalna instrukcja obsługi

63 – 74

REBARBADORA ANGULAR

Manual original

38 – 49

SMERIGLIATRICE ANGOLARE

Istruzioni originali

50 – 62

ESMERILADORA ANGULAR

Instrucciones de uso originales

1706R01 147716V3© 2017 SPARKY

Оригинална инструкция за използване

114 – 126

ЪГЛОШЛИФОВЪЧНА МАШИНА

750 W

850 W

M 750 HD • M 750E HD

M 850 HD • M 850E HD

6 March 2017

Manufacturer

SPARKY Power Tools GmbH

Leipziger Str. 20

10117 Berlin, GERMANY

Signature of authorized person

A. Ivanov

Technical director of SPARKY ELTOS AD

DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product, described under “Technical specications”, fulls all the relevant provisions of the

following directives and the harmonized standards: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Technical le is stored at SPARKY ELTOS AD, Kubrat Str. 9, 5500 Lovech, Bulgaria.

KONFORMITÄTSERKLÄRUNG

Hiermit versichern wir unsere persönliche Haftung, dass Produkt im Abschnitt “Technische Daten“ beschrieben“ allen einschlägigen

Bestimmungen folgender Richtlinien und entsprechender harmonisierten Standards entspricht: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Die technischen Unterlagen werden bei SPARKY ELTOS AD, Kubrat Str.9, 5500 Lovech, Bulgarien, aufbewahrt.

DECLARATION DE CONFORMITE

Nous déclarons sous notre responsabilité que le produit décrit dans la rubrique “Données techniques” satisfait à l’ensemble des dispositions

pertinentes des présentes directives, respectivement aux normes harmonisées: 2006/42/CЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Le dossier technique est conservé par SPARKY ELTOS AD, 9, rue Kubrat, 5500 Lovech, Bulgarie.

DICHIARAZIONE DI CONFORMITÀ

Noi dichiariamo sotto la nostra personale responsabilità, che il prodotto, descritto nella sezione “Dati tecnici” è in conformità a tutte le disposizioni

pertinenti della presente direttive e norme armonizzate: 2006/42/CЕ,2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Il fascicolo tecnico viene custodito presso la SPARKY ELTOS AD, 5500 Lovech, via Kubrat n. 9, Bulgaria.

DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que el producto, descrito en los “Datos técnicos”, está conforme con todas las disposiciones

aplicables de la presente directrices aplicables y las correspondientes normas armonizadas: 2006/42/CЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

El expediente técnico está archivado en SPARKY ELTOS AD, C/ Kubrat, 9, 5500 Lovech, Bulgaria.

DECLARAÇÃO DE CONFORMIDADE

Declaramos assumindo a nossa responsabilidade pessoal que el producto, descrito en los “Dados técnicos”, está conforme com todas as

disposições relevantes da presente directrizes aplicáveis e respectivos estandartes harmonizados: 2006/42/CЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

A documentação técnica guarda-se no SPARKY ELTOS AD, rua Kubrat 9, 5500, Lovech, Bulgária.

DEKLARACJA ZGODNOŚCI

Niniejszym deklarujemy naszą osobistą odpowiedzialnością, że produkt, przedstawiony w rozdziale „Dane techniczne“, pełnia wszystkie

odpowiednie postanowienia następujących dyrektyw i harmonizowanych standardów: 2006/42/WЕ, 2014/30/UE, 2011/65/UE,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Teczka techniczna przechowywana jest w SPARKY ELTOS AD, Kubrat Str.9, 5500 Lovetch, Bułgaria.

ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ

Мы заявляем со всей ответственностью, что продукт, описанный в разделе “Технические данные“, полностью соответствует всем

соответствующим требованиям действующих директив и гармонизированных стандартов: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Техническое досье хранится в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, Болгария.

ДЕКЛАРАЦІЯ ПРО ВІДПОВІДНІСТЬ

Ми заявляємо під свою власну відповідальність, що продукт, описаний у розділі “Teхнічні дані“ відповідає всім діючим вимогам директив і

гармонізованих стандартів: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Технічне досьє зберігається в СПАРКИ ЕЛТОС АД, ул. Кубрат № 9, 5500 Ловеч, Болгарія.

ДЕКЛАРАЦИЯ ЗА СЪОТВЕТСТВИЕ

Ние декларираме на своя лична отговорност, че изделието, описано в раздел “Технически данни”, отговаря на всички приложими

изисквания на следните директиви и хармонизирани стандарти: 2006/42/ЕС, 2014/30/EU, 2011/65/EU,

EN 60745-1, EN 60745-2-3; EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 50581.

Техническото досие се съхранява в СПАРКИ ЕЛТОС АД, ул. Кубрат №9, 5500 Ловеч, България.

BLACK PANTONE185

BLACK PANTONE185

Page is loading ...

1

EN

Introduction

Your new SPARKY power tool will more than satisfy your expectations. It has been manufactured

under stringent SPARKY Quality Standards to meet superior performance criteria. You will nd your

new tool easy and safe to operate, and, with proper care, it will give you many years of dependable

service.

WARNING:

Carefully read through these Original Instructions before using your new SPARKY power tool.

Take special care to heed the Warnings. Your SPARKY power tool has many features that will

make your job faster and easier. Safety, performance, and dependability have been given top

priority in the development of this tool, making it easy to maintain and operate.

Do not dispose of electric tools together with household waste!

Waste electrical products should not be disposed of with household waste. Please recycle

where facilities exist. Check with your local authority or retailer for recycling advice.

ENVIRONMENTAL PROTECTION

The machine, accessories and packaging should be sorted for environmental-friendly

recycling.

The plastic components are labelled for categorised recycling.

UNPACKING

Due to modern mass production techniques, it is unlikely that your power tool is faulty or that a part is

missing. If you nd anything wrong, do not operate the tool until the parts have been replaced or the

fault has been rectied. Failure to do so could result in serious personal injury.

ASSEMBLY

The angle grinder is packed fully assembled except for the wheel guard and the auxiliary handle.

Contents

Introduction ............................................................................................................................... 1

Technical specications ...........................................................................................................3

General power tool safety warnings ..........................................................................................4

Angle grinder safety warnings ....................................................................................................5

Know your product ................................................................................................................ A/8

Operation ...............................................................................................................................B/8

Maintenance ...........................................................................................................................10

Warranty .................................................................................................................................. 11

M 750 HD ● M 750E HD ● M 850 HD ● M 850E HD ● Original instructions

2

EN

M 750 HD ● M 750E HD ● M 850 HD ● M 850E HD

DESCRIPTION OF SYMBOLS

The rating plate on your power tool may show symbols. These represent important information about

the product or instructions on its use.

Double insulated for additional protection.

Spindle thread: M14

Conforms to the relevant European Directives.

Conforms to the requirements of Customs Union regulations.

Conforms to the requirements of Ukrainian standards.

Refer to Original Instructions.

Always wear eye protection.

YYYY-Www Production period, where the variable symbols are:

YYYY- year of manufacture,

ww - calendar week number.

M Angle grinder.

3

Original instructions

EN

The vibration emission level given in this information sheet has been measured in accordance with

a standardised test given in EN 60745 and may be used to compare one tool with another. It may be

used for a preliminary assessment of exposure.

The declared vibration emission level represents the main applications of the tool. However if the tool

is used for different applications, with different accessories or poorly maintained, the vibration emis-

sion may differ. This may signicantly increase the exposure level over the total working period.

An estimation of the level of exposure to vibration should also take into account the times when the

tool is switched off or when it is running but not actually doing the job. This may signicantly reduce

the exposure level over the total working period.

Maintain the power tool and the accessories and keep your hands warm during operation to reduce

the harmful effect of vibrations.

Other applications such as cutting-off or wire brushing may have different vibration emission values.

Dust from material such as paint containing lead, some wood species, minerals and metal may be

harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory dis-

eases to the operator or bystanders.

Technical specications

Model M750 HD M750E HD

M850 HD M850E HD

Power input 750W 750W

850W 850W

Rated speed 10000 min

-1

3000-10000 min

-1

Spindle thread M14 M14

Spindle thread length 20 mm 20 mm

Wheel arbor 22,23 mm 22,23 mm

Max. wheel diameter 125 mm 125 mm

Max. wheel thickness 6 mm 6 mm

Weight (EPTA 2,0 kg 2,1 kg

Procedure 01/2014) 2,2 kg 2,3 kg

Safety class (EN 60745-1) II II

NOISE AND VIBRATION INFORMATION

Measured values determined according to EN 60745

Noise emission

A-weighted sound pressure level L

pA

89 dB(A) 89 dB(A)

91 dB(A) 91 dB(A)

Uncertainty К

pA

3,0 dB(A) 3,0 dB(A)

A-weighted sound power level L

wA

100 dB(A) 100 dB(A)

102 dB(A) 102 dB(A)

Uncertainty К

wA

3,0 dB(A) 3,0 dB(A)

Wear hearing protection!

Vibration emission *

Total vibration values (vector sum in the three axes) determined according to EN 60745:

Surface grinding

Vibration emission value a

h,AG

5,2 m/s

2

5,2 m/s

2

5,2 m/s

2

5,2 m/s

2

Uncertainty К

AG

1,5 m/s

2

1,5 m/s

2

Sanding

Vibration emission value a

h,DS

4,6 m/s

2

4,6 m/s

2

Uncertainty К

DS

1,5 m/s

2

* The vibration emission values are determined according to 6.2.7 EN 60745.

4

EN

M 750 HD ● M 750E HD ● M 850 HD ● M 850E HD

General power tool

safety warnings

WARNING! Read all safety warn-

ings and all instructions. Failure to follow

the warnings and instructions may result in

electric shock, re and/or serious injury.

Save all warnings and instructions for

future reference.

The term “power tool” in the warnings refers to

your mains-operated (corded) power tool or bat-

tery-operated (cordless) power tool.

1) Work area safety

a) Keep work area clean and well lit. Clut-

tered or dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence

of ammable liquids, gases or dust.

Power tools create sparks which may ignite

the dust or fumes.

c) Keep children and bystanders away

while operating a power tool. Distrac-

tions can cause you to lose control.

2) Electrical safety

a) Power tool plugs must match the outlet.

Never modify the plug in any way. Do

not use any adapter plugs with earthed

(grounded) power tools. Unmodied

plugs and matching outlets will reduce risk

of electric shock.

b) Avoid body contact with earthed or

grounded surfaces, such as pipes, ra-

diators, ranges and refrigerators. There

is an increased risk of electric shock if your

body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool

will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging

the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the

risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for out-

door use. Use of a cord suitable for out-

door use reduces the risk of electric shock.

f) If operating a power tool in a damp lo-

cation is unavoidable, use a residual

current device (RCD) protected supply.

Use of an RCD reduces the risk of electric

shock.

3) Personal safety

a) Stay alert, watch what you are doing

and use common sense when operating

a power tool. Do not use a power tool

while you are tired or under the inu-

ence of drugs, alcohol or medication.

A moment of inattention while operating

power tools may result in serious personal

injury.

b) Use personal protective equipment.

Always wear eye protection. Protective

equipment such as dust mask, non-skid

safety shoes, hard hat, or hearing protec-

tion used for appropriate conditions will re-

duce personal injuries.

c) Prevent unintentional starting. Ensure

the switch is in the off-position before

connecting to power source and/or bat-

tery pack, picking up or carrying the

tool. Carrying power tools with your nger

on the switch or energising power tools that

have the switch on invites accidents.

d) Remove any adjusting key or wrench be-

fore turning the power tool on. A wrench

or a key left attached to a rotating part of

the power tool may result in personal in-

jury.

e) Do not overreach. Keep proper footing

and balance at all times. This enables

better control of the power tool in unexpect-

ed situations.

f) Dress properly. Do not wear loose cloth-

ing or jewellery. Keep your hair, cloth-

ing and gloves away from moving parts.

Loose clothes, jewellery or long hair can be

caught in moving parts.

g) If devices are provided for the connec-

Certain kinds of dust are classied as carcinogenic such as oak and beech dust especially in conjunc-

tion with additives for wood conditioning (chromate, wood preservative). Material containing asbestos

must only be treated by specialists.

▪ Where the use of a dust extraction device is possible it shall be used.

▪ The work place must be well ventilated.

▪ The use of a dust mask of lter class P2 is recommended.

Follow national requirements for the materials you want to work with.

5

Original instructions

EN

tion of dust extraction and collection fa-

cilities, ensure these are connected and

properly used. Use of dust collection can

reduce dust-related hazards.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power

source and/or the battery pack from the

power tool before making any adjust-

ments, changing accessories, or stor-

ing power tools. Such preventive safety

measures reduce the risk of starting the

power tool accidentally.

d) Store idle power tools out of the reach

of children and do not allow persons

unfamiliar with the power tool or these

instructions to operate the power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for mis-

alignment or binding of moving parts,

breakage of parts and any other condi-

tion that may affect the power tool’s op-

eration. If damaged, have the power tool

repaired before use. Many accidents are

caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean.

Properly maintained cutting tools with

sharp cutting edges are less likely to bind

and are easier to control.

g) Use the power tool, accessories and

tool bits etc. in accordance with these

instructions, taking into account the

working conditions and the work to be

performed. Use of the power tool for op-

erations different from those intended could

result in a hazardous situation.

5) Service

a) Have your power tool serviced by a

qualied repair person using only iden-

tical replacement parts. This will ensure

that the safety of the power tool is main-

tained.

Angle grinder safety

warnings

Safety Warnings Common for Grinding,

Sanding, Wire Brushing, Polishing or

Abrasive Cutting-Off Operations:

a) This power tool is intended to func-

tion as a grinder, sander, wire brush,

polisher or cut-off tool. Read all safety

warnings, instructions, illustrations and

specications provided with this power

tool. Failure to follow all instructions listed

below may result in electric shock, re and/

or serious injury.

b) This power tool is not recommended for

polishing. Operations for which the power

tool was not designed may create a hazard

and cause personal injury.(M 750 HD,

M 850 HD)

c) Do not use accessories which are

not specically designed and recom-

mended by the tool manufacturer. Just

because the accessory can be attached to

your power tool, it does not assure safe op-

eration.

d) The rated speed of the accessory must

be at least equal to the maximum speed

marked on the power tool. Accessories

running faster than their rated speed can

break and y apart.

e) The outside diameter and the thickness

of your accessory must be within the

capacity rating of your power tool. In-

correctly sized accessories cannot be ad-

equately guarded or controlled.

f) Threaded mounting of accessories

must match the grinder spindle thread.

For accessories mounted by anges,

the arbour hole of the accessory must

t the locating diameter of the ange.

Accessories that do not match the mount-

ing hardware of the power tool will run out

of balance, vibrate excessively and may

cause loss of control.

g) Do not use a damaged accessory. Be-

fore each use inspect the accessory

such as abrasive wheels for chips and

cracks, backing pad for cracks, tear or

excess wear, wire brush for loose or

cracked wires. If power tool or acces-

sory is dropped, inspect for damage or

install an undamaged accessory. After

inspecting and installing an accessory,

position yourself and bystanders away

6

EN

M 750 HD ● M 750E HD ● M 850 HD ● M 850E HD

from the plane of the rotating accessory

and run the power tool at maximum no-

load speed for one minute. Damaged ac-

cessories will normally break apart during

this test time.

h) Wear personal protective equipment.

Depending on application, use face

shield, safety goggles or safety glasses.

As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron

capable of stopping small abrasive or

workpiece fragments. The eye protection

must be capable of stopping ying debris

generated by various operations. The dust

mask or respirator must be capable of l-

trating particles generated by your opera-

tion. Prolonged exposure to high intensity

noise may cause hearing loss.

i) Keep bystanders a safe distance away

from work area. Anyone entering the

work area must wear personal protec-

tive equipment. Fragments of workpiece

or of a broken accessory may y away and

cause injury beyond immediate area of op-

eration.

j) Hold the power tool by insulated grip-

ping surfaces only, when performing an

operation where the cutting accessory

may contact hidden wiring or its own

cord. Cutting accessory contacting a “live”

wire may make exposed metal parts of the

power tool “live” and could give the opera-

tor an electric shock.

k) Position the cord clear of the spinning

accessory. If you lose control, the cord

may be cut or snagged and your hand or

arm may be pulled into the spinning acces-

sory.

l) Never lay the power tool down until the

accessory has come to a complete stop.

The spinning accessory may grab the sur-

face and pull the power tool out of your con-

trol.

m) Do not run the power tool while carrying

it at your side. Accidental contact with the

spinning accessory could snag your cloth-

ing, pulling the accessory into your body.

n) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust

inside the housing and excessive accumu-

lation of powdered metal may cause electri-

cal hazards.

o) Do not operate the power tool near am-

mable materials. Sparks could ignite these

materials.

p) Do not use accessories that require

liquid coolants. Using water or other liq-

uid coolants may result in electrocution or

shock.

▪ The tool must be used only for its pre-

scribed purpose. Any use other use

than those mentioned in this Instruction

will be considered a case of misuse. The

user and not the manufacturer shall be li-

able for any damage or injury resulting from

such cases of misuse.

▪ The manufacturer shall not be liable for

any changes made to the tool nor for any

damage resulting from such changes.

▪ When operating in dusty environment,

the ventilation slots must be kept clean.

If it should become necessary to clear

dust, rst disconnect the tool from the

mains supply (use non metallic objects

to clean the dust) and avoid damaging

internal parts. The power tool will over-

heat under deteriorated cooling due to the

clogged with dust ventilation slots.

Further safety instructions for all opera-

tions

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or

snagged rotating wheel, backing pad, brush

or any other accessory. Pinching or snagging

causes rapid stalling of the rotating accessory

which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the ac-

cessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into

the surface of the material causing the wheel to

climb out or kick out. The wheel may either jump

toward or away from the operator, depending on

direction of the wheel’s movement at the point of

pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/

or incorrect operating procedures or conditions

and can be avoided by taking proper precau-

tions as given below.

a) Maintain a rm grip on the power tool

and position your body and arm to al-

low you to resist kickback forces. Al-

ways use auxiliary handle, if provided,

for maximum control over kickback or

torque reaction during start-up. The

operator can control torque reactions or

kickback forces, if proper precautions are

7

Original instructions

EN

taken.

b) Never place your hand near the rotating

accessory. Accessory may kickback over

your hand.

c) Do not position your body in the area

where power tool will move if kickback

occurs. Kickback will propel the tool in di-

rection opposite to the wheel’s movement

at the point of snagging.

d) Use special care when working corners,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to

snag the rotating accessory and cause loss

of control or kickback.

e) Do not attach a saw chain woodcarving

blade or toothed saw blade. Such blades

create frequent kickback and loss of con-

trol.

▪ Fix the machined piece in vice or in an-

other appropriate way.

Safety Warnings Specic for Grinding

and Abrasive Cutting-Off Operations:

a) Use only wheel types that are recom-

mended for your power tool and the

specic guard designed for the selected

wheel. Wheels for which the power tool

was not designed cannot be adequately

guarded and are unsafe.

b) The grinding surface of centre de-

pressed wheels must be mounted below

the plane of the guard lip. An improperly

mounted wheel that projects through the

plane of the guard lip cannot be adequately

protected.

c) The guard must be securely attached

to the power tool and positioned for

maximum safety, so the least amount

of wheel is exposed towards the opera-

tor. The guard helps to protect the operator

from broken wheel fragments, accidental

contact with wheel and sparks that could

ignite clothing.

d) Wheels must be used only for recom-

mended applications. For example: do

not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for

peripheral grinding, side forces applied to

these wheels may cause them to shatter.

e) Always use undamaged wheel anges

that are of correct size and shape for

your selected wheel. Proper wheel

anges support the wheel thus reduc-

ing the possibility of wheel breakage.

Flanges for cut-off wheels may be different

from grinding wheel anges.

f) Do not use worn down wheels from larg-

er power tools. Wheel intended for larger

power tool is not suitable for the higher

speed of a smaller tool and may burst.

▪ Always pay attention to the wheel rota-

tion direction. The torque reaction is in the

opposite direction of the rotation direction

at the point of binding and this is a prereq-

uisite to loosing control of the power tool.

▪ Always guide the machine in such a way

that sparks and dust can scatter away

from your body. Power tools generate

sparks which may burn your clothes or un-

protected parts of your body.

▪ Grinding and cutting-off operations on

freshly painted metal structures is not

allowed before the paint has become

dry. There is a risk of damp paint ignition.

▪ Cutting of ammable materials (wood,

plastics, etc.) and panel structures

“sandwich” type with ammable lling

is not allowed. There is a risk of re.

▪ Grinding and cutting-off operations on

equipment operating under pressure is

not allowed. There is a risk of explosion.

▪ Grinding and cutting-off operations of

reservoirs, pipelines, equipment, etc.,

containing at present or having con-

tained ammable or easily ignitable

substances or materials is not allowed

without rst taking special precautions

to prevent re and explosion. There is a

risk of re and explosion.

Additional Safety Warnings Specic for

Abrasive Cutting-Off Operations:

a) Do not “jam” the cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut. Over-

stressing the wheel increases the loading

and susceptibility to twisting or binding of

the wheel in the cut and the possibility of

kickback or wheel breakage.

b) Do not position your body in line with

and behind the rotating wheel. When the

wheel, at the point of operation, is moving

away from your body, the possible kickback

may propel the spinning wheel and the

power tool directly at you.

c) When wheel is binding or when inter-

rupting a cut for any reason, switch off

the power tool and hold the power tool

motionless until the wheel comes to a

complete stop. Never attempt to remove

8

EN

M 750 HD ● M 750E HD ● M 850 HD ● M 850E HD

the cut-off wheel from the cut while the

wheel is in motion otherwise kickback

may occur. Investigate and take corrective

action to eliminate the cause of wheel bind-

ing.

d) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut. The

wheel may bind, walk up or kickback if the

power tool is restarted in the workpiece.

e) Support panels or any oversized work-

piece to minimize the risk of wheel

pinching and kickback. Large workpiec-

es tend to sag under their own weight.

Supports must be placed under the work-

piece near the line of cut and near the

edge of the workpiece on both sides of the

wheel.

f) Use extra caution when making a “pock-

et cut” into existing walls or other blind

areas. The protruding wheel may cut gas

or water pipes, electrical wiring or objects

that can cause kickback.

Safety Warnings Specic for Sanding

Operations:

a) Do not use excessively oversized sand-

ing disc paper. Follow manufacturer’s

recommendations, when selecting

sanding paper. Larger sanding paper ex-

tending beyond the sanding pad presents

a laceration hazard and may cause snag-

ging, tearing of the disc or kickback.

Safety Warnings Specic for Polishing

Operations:

a) Do not allow any loose portion of the po-

lishing bonnet or its attachment strings

to spin freely. Tuck away or trim any

loose attachment strings. Loose and

spinning attachment strings can entangle

your ngers or snag on the workpiece.

Safety Warnings Specic for Wire

Brushing Operations:

a) Be aware that wire bristles are thrown

by the brush even during ordinary op-

eration. Do not overstress the wires by ap-

plying excessive load to the brush. The wire

bristles can easily penetrate light clothing

and/or skin.

b) If the use of a guard is recommended for

wire brushing, do not allow any interfer-

ence of the wire wheel or brush with the

guard. Wire wheel or brush may expand in

diameter due to work load and centrifugal

forces.

Know your product

Before using the power tool, familiarize your-

self with all the operating features and safety

requirements.

Use the tool and accessories only for the ap-

plications intended. All other applications are

expressly ruled out.

1. Spindle

2.1. Wheel guard for grinding wheel

2.2. Wheel guard for cutting wheel*

3. Support ange

4.1. Grinding wheel (Use only with

a wheel guard for grinding wheel!)*

4.2. Cutting wheel (Use only with

a wheel guard for cutting wheel!)*

5. Fixing ange

6. Auxiliary handle

7. ON/OFF switch

8. Electronic regulator of rotation speed

(M 750E HD, M 850E HD)

9. Spindle lock button

ACCESSORIES TO BE USED WITH

THIS POWER TOOL

10. Wire cup brush*

11. Plastic (rubber) backing pad*

12. Sandpaper or polishing bonnet*

13. Lock nut*

* The additional accessories shown in the illus-

trations or described in the text are not included

in the delivery.

Operation

These power tools are supplied from single-

phase alternating current mains only. They

are double insulated according to EN 60745,

IEC 60745-1 and can be connected to grounded

or not grounded sockets. This power tool is radio

suppressed in compliance with EMC Directive.

This power tool is designed for cutting, grinding

and brushing mainly metals without using wa-

ter.

PRIOR TO INITIAL OPERATION

▪ The machine may be delivered with the wheel

guard mounted at the factory. Ensure that the

wheel guard is mounted properly and xed

reliably prior to the initial and any following

9

Original instructions

EN

operation.

▪ The machine may be delivered with the wheel

mounted at the factory. Ensure that the wheel

is mounted properly and xed reliably prior to

the initial and any following operation.

▪ Make sure the power supply voltage corre-

sponds to the value indicated on the name

plate with technical data of the tool.

▪ Always check the position of ON/OFF switch.

The power tool must be connected to the

power supply socket only when this switch is

in OFF position. If the plug is connected to

a receptacle while the power switch is in the

ON position, the power tool will start operat-

ing immediately, which could cause a serious

accident.

▪ Make sure that the cord and the plug are in

order. If the replacement of the supply cord is

necessary, this has to be done by the manu-

facturer or his agent in order to avoid a safety

hazard.

WARNING: Always switch off and un-

plug the power tool prior to any adjustment,

servicing or maintenance.

▪ When using diamond cutting discs, pay atten-

tion that the direction-of-rotation arrow on the

diamond cutting disc and the direction of rota-

tion of the machine (see direction-of-rotation

arrow on the machine head) agree.

▪ Make sure the grinding wheel diameter and

thickness do not exceed the values specied

on the name plate. The peripheral speed in-

dicated on the wheel must not be less than

80 m/s. The wheels must be stored according

the recommendations of the manufacturer.

▪ In case the work area is remote from the pow-

er source, use as short as practicable exten-

sion cord with proper cross-section.

▪ Check that the auxiliary handle is properly

mounted and reliably tightened.

SWITCHING ON - SWITCHING OFF

Switching on: Push the back end of the ON/OFF

switch 7 down and then forward in the direction

of the arrow until its front end will sag, thus x-

ing itself.

Switching off: press the back, lifted end of switch

7 and release it to return in its initial position.

ADJUSTING THE ROTATION SPEED

(M 750E HD, M 850E HD)

Continuous operation at low rpm is not recom-

mended for the following machines: М 750Е HD,

M 850E HD.

The rotation speed can be varied smoothly by

turning electronic regulator 8, placed on the

rear of the grinder. In the table below the rec-

ommended regulator positions for the different

areas of applications are specied:

Area of application Regulator position

1. Plastics grinding with plastic disk A - C

and abrasive cloth (paper)

2. Wood grinding and removing B - D

lacquer and dye coatings

3. Metal grinding with plastic disk and C - F

abrasive cloth (paper)

4. Dust removing with cup brush D - F

5. Rough cleaning, metal or stone cutting G

6. Polishing with plastic disk and A - B

polishing jacket

Model M 850E HD is equipped with full-wave

electronics for

- Soft start and restriction of the starting cur-

rent;

- Speed pre-selection and control.

WHEEL GUARD

WARNING: The wheel guard 2.1 for

grinding wheel or the wheel guard 2.2 for

cutting wheel (for grinding wheel 4.1 or cut-

ting wheel 4.2 accordingly) must always be

mounted on the machine!

Its position can be different and depends on

which side the auxiliary handle is placed, as well

as when the machine is mounted on a stand.

GRINDING WHEEL REPLACEMENT

Secure spindle 1 by depressing the spindle lock

button 9 provided on the gear case.

WARNING: Never press button 9

while the spindle is still rotating!

(With this button depressed turn the spindle till

its pronounced going deeper). ). Unscrew the

xing ange 5 by a lock nut wrench. Place the

new wheel on thesupport ange 3 with the in-

scriptions facing up, and screw down ange 5

facing its at side towards the wheel, using the

10

EN

M 750 HD ● M 750E HD ● M 850 HD ● M 850E HD

lock nut wrench. Use blotters if the wheel has

been delivered with them. After replacing the

wheel operate the machine with the new wheel

in no load mode for one minute. Vibrating or

otherwise improperly rotating wheels must be

replaced immediately and discarded.

Cup brushes 10 are screwed directly on spindle

1 by means of an open-end spanner. (Check if

the brush thread length is sufcient to accept the

spindle thread.)

Grinding and polishing with abrasive sanding

disks is accomplished by means of plastic rub-

ber backing disk (pad) 11, under which sanding

disks and polishing jackets 12 are mounted.

Place plastic backing pad 11 on the support

ange 3 and secure it with lock nut 13, delivered

with the tool. In case the exible backing pad

is equipped with a ange, the pad is screwed

directly onto the spindle by a wrench without

using the xing ange 5. The pad with ange

may be a resin lled sponge, foam polyurethane

sponge with plastic insert for the nut with hook-

and-loop fastening to the sandpaper or the bon-

net. After replacing the pad perform a trial run

for one minute at no load. Vibrating or otherwise

improperly rotating pads must be replaced im-

mediately.

MOUNTING THE WHEEL GUARD

Before performing the following operations,

switch the machine off and withdraw the plug

from the socket.

Mounting the wheel guard (Fig. 1)

- Rotate the black plastic ring (Fig. 2a), so

that the crevice S of the ring coincides with the

groove for the tooth of the xing lever L.

- Place the wheel guard in non-operating

position (Fig.2a) so that the four teeth coin-

cide with the four grooves in the bearing seat

(Fig.2b).

- Press the fastening lever L (g.3) to re-

lease it.

- Press the wheel guard down and rotate it

in the necessary operating position (Fig.4).

- Release the fastening lever L to a stable

position in which the wheel guard is xed (the

xing lever tooth enters into one of the guard

grooves).

Rotating the wheel guard in a new operating

position

- Press the fastening lever L (Fig.3) to re-

lease it.

- Rotate the wheel guard to the necessary

operating position.

- Release the fastening lever L to a stable

position in which the wheel guard is xed (the

xing lever tooth enters into one of the guard

grooves).

Removing the wheel guard

- Press the fastening lever L (Fig.3) to re-

lease it.

- Rotate the wheel guard in non-operating

position (Fig.2a) so that the four teeth coin-

cide with the four grooves in the bearing seat

(Fig.2b).

- Remove the wheel guard.

AUXILIARY HANDLE

Normally auxiliary handle 6 is screwed on the

machine left side. It can be mounted also on the

machine right side if this is more convenient for

the operator.

TURNING THE MACHINE CASE

The machine case can be turned to 90° or to

180°. The rst way of mounting is implemented

when the machine is used mainly for cutting,

and the second - in case the operator works bet-

ter with his left hand. In both cases the case

turning must be carried out in a specialised serv-

ice centres for SPARKY power tools.

RECOMMENDATIONS

When cutting, do not apply pressure, do not os-

cillate the wheel. Work with moderate feed rate,

suited to the material to be machined.

The direction of cutting is very signicant. The

machine must always be fed against the direc-

tion of wheel rotation. Otherwise, danger exists

for the wheel to be forced uncontrolled out of

the cut.

When cutting proles or rectangular pipes it is

best to start with the smallest cross section.

When grinding do not apply pressure to the

processed surface by rearing down on the ma-

chine but move the wheel regularly backwards

and forwards. Special wheels shall be used for

processing non-ferrous metals. Best results

when roughing can be achieved with the wheel

inclined at 30

0

to 40

0

to the processed surface

Never use cutting wheels for roughing opera-

tions. Usage of wheels thicker than 6 mm is not

recommended.

11

Original instructions

EN

Maintenance

WARNING: Always ensure that the

tool is switched off and unplugged before

attempting to perform inspection or mainte-

nance.

BRUSH REPLACEMENT

This power tool is equipped with auto-stop

brushes. When the carbon brushes are worn

out, the machine switches itself off. In this case

both brushes must be replaced simultaneously

with genuine brushes at SPARKY service centre

for warranty and post-warranty service.

GENERAL INSPECTION

Regularly inspect all fasteners and ensure they

are properly tightened. Should any of the screws

be loose, retighten it immediately to avoid haz-

ards.

If the replacement of the supply cord is neces-

sary, this has to be done by the manufacturer or

his agent in order to avoid a safety hazard.

CLEANING

For safe operation always keep the machine

and its ventilation slots clean.

Regularly check to see if any dust or foreign mat-

ter has entered the ventilation slots and the grills

around the switches. Use a soft brush and/or air

jet to remove any accumulated dust. Wear safety

glasses to protect your eyes whilst cleaning.

Exterior plastic parts may be cleaned with a

damp cloth and mild detergent if necessary.

When operating in heavily dusty environment

(cutting stone) the ventilation slots and the

switch slider of the machine running at no load

must be obligatory cleaned after each shift

(every 8 h operation) by compressed air or by

gently tapping it near the ventilation slots with

non-metal object (Fig.6a,6b).

WARNING: Never use alcohol, petrol

or other cleaning agent. Never use caustic

agents to clean plastic parts.

WARNING: Water must never come

into contact with the tool.

IMPORTANT! To assure product safety and re-

liability, repairs, maintenance and adjustment

(including brush inspection and replacement)

should be performed by certied service centres

or other qualied service organisations, always

using genuine replacement parts.

Warranty

The guarantee period for SPARKY power tools

is determined in the guarantee card.

Faults due to normal wear, overloading or im-

proper handling will be excluded from the guar-

antee.

Faults due to defective materials implemented

as well as defects in workmanship will be cor-

rected free of charge through replacement or

repair.

The complaints for defective SPARKY power

tools will be recognized if the machine is sent

back to the dealer or is presented to the author-

ised warranty service centre undismantled, in its

initial condition.

Notes

Carefully read the entire Instruction Manual be-

fore using this product.

The manufacturer reserves the right to make

changes and improvements to the products and

to alter specications without prior notice.

Specications may differ from country to coun-

try.

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Page is loading ...

Sparky M 850 HD User manual

Brand: Sparky

Model: M 850 HD

Category: Power tools

Type: User manual

This manual is also suitable for

Download PDF

in other languages

italiano: Sparky M 850 HD Manuale utente
français: Sparky M 850 HD Manuel utilisateur
español: Sparky M 850 HD Manual de usuario
Deutsch: Sparky M 850 HD Benutzerhandbuch
русский: Sparky M 850 HD Руководство пользователя
português: Sparky M 850 HD Manual do usuário
polski: Sparky M 850 HD Instrukcja obsługi

Related papers

Other documents