Remington BPS188A Owner's manual

Brand: Remington

Model: BPS188A

Category: Power chainsaws

Type: Owner's manual

This manual is also suitable for

BS188A

VOLT CO

VOLT COR

OWNER'S MANUAL

SAW

Polesaw Model

BPS188A (8"/20.3 cm)

Chain Saw ModeJ

BS188A (8"/20.3 cm)

iMPORTANT: Read and understand this manual before assembling or

operating this saw. improper use of saw can cause severe injury. Keep

this manual for future reference.

DO NOT RETURN PRODUCT TO STORE.

CALL 1-800-626-2237 FOR TECHNICAL ASSISTANCE

For more information, visit www.remingtonpowertools.com

This manual is your guide to safe and proper operation of the saw.

SAVE THESE iNSTRUCTiONS.

Keep your purchase receipt for warranty coverage.

NO DEVUELVA EL PRODUCTO A LA TIENDA

Para mas informaci6n, www.remingtonpowertools.com

PARA AYUDA TI_CNICA LLANIE AL 1-800-626-2237

Este manual es su guia para utilizar esta sierra electrica de

manera adecuada y segura.

GUARDE ESTAS INSTRUCCIONES.

Guarde su recibo de compra para cobertura de ia garantia.

www. remingtonpowertoo/s, com 2

iNTRODUCTiON

Your Remington Cordless Polesaw and Cordless Chainsaw may have been purchased together (as a 2-in-] polesaw/chainsaw) or

seperate (chainsaw only). If the chainsaw was purchased separately, the pole is available as an accessory and may be purchased by

visiting the "On-Line Outlet" at www.remingtonpowertools.com.

CONTENTS

iMPORTANT SAFETY iNFORMATiON ....................................................................... 4

Before Operating Saw .......................................................................................................... 4

While Operating Saw ........................................................................................................... 4

Kickback ............................................................................................................................... 5

Maintenance and Storage of Saw ........................................................................................ 5

Polesaw Trimming Precautions ............................................................................................ 6

UNPACKING ................................................................................................................ 6

PRODUCT IDENTIFICATION ...................................................................................... 7

Chain Saw ............................................................................................................................ 7

Polesaw ................................................................................................................................ 7

CHAIN TERMS AND DEFINITIONS ............................................................................ 8

RECHARGEABLE BATTERY. ..................................................................................... 9

Protective Battery Terminal Cap ........................................................................................... 9

Safety Warnings ................................................................................................................... 9

Charging Battery ................................................................................................................ 10

Important Charging Notes .................................................................................................. 10

CHAIN SAW INFORMATION ..................................................................................... 11

Chain Saw Assembly ......................................................................................................... 11

Saw Chain Tension ............................................................................................................. 11

Oiling Chain ........................................................................................................................ 12

Cutting with the Chain Saw ................................................................................................ 12

Felling a Tree (Cutting Down a Tree) ................................................................................. 12

Limbing a Tree ................................................................................................................... 13

Bucking A Log .................................................................................................................... 14

Trimming a Tree (Pruning) ................................................................................................. 14

POLESAW iNFORMATiON ....................................................................................... 15

Polesaw Assembly ............................................................................................................. 15

Adjusting Pole Length ........................................................................................................ 15

Cutting with the Polesaw .................................................................................................... 15

CLEANING AND MAINTENANCE ............................................................................. 16

Cleaning Saw Body ............................................................................................................ 16

Care of Guide Bar .............................................................................................................. 16

Sharpening Saw Chain ...................................................................................................... 16

Replacing Saw Chain ......................................................................................................... 17

STORAGE .................................................................................................................. 18

TECHNICAL SERVICE .............................................................................................. 18

REPLACEMENT PARTS AND ACCESSORIES ....................................................... 18

REPAIR SERVICE ..................................................................................................... 18

BATTERY RECYCLING ............................................................................................. 18

TROUBLESHOOTING ............................................................................................... 19

WARRANTY INFORMATION ..................................................................................... 20

ILLUSTRATED PARTS BREAKDOWN .................................................................... 43

PARTS CENTRALS ................................................................................................... 45

3 www. remingtonpowertoo/s, com

iMPORTANT SAFETY iNFORMATiON

READ ALL iNSTRUCTiONS.

Make sure you read and under=

stand all instructions inimportant

Safetylnformation. Improper use

ofthis chain saw cancause severe

injury or death from fire, electrical

shock, body contact with moving

chain, or failing wood.

DANGER: Serious injury or

death from electrocution if power

lines are contacted. Never use

near any electrical source, wires,

or power lines.

dBk WARNING: When using a bat-

tery operated chain saw, basic

safety precautions should always

be followed to reduce the risk of

fire and injury to persons, includ-

ing the following:

411 WARNING: For safe opera=

tion read and understand own-

ers manual. Wear face shield

(and/or safety glasses) and hard

hat to protect against failing de-

bris. Always have a clear work

area, retreat path, and be aware

of limb/branch IDeation to avoid

failing limbs and debris. Keep

bystanders 50 ft(Sm) away when

operating saw. Store indoors.

BEFORE OPERATING SAW

For safe operation read and understand this

owner's manual betore operating saw.

Only well-instructed adults should operale

saw. Never allow children to operale saw.

Keep Work Area Clean

Cluttered work areas invite injuries. Betore

cutting, always provide the following:

° clear work area

° secure footing

° planned retreat path from falling

tree

Consider Work Area Environment

1. Do not operate saw

° in rain or snow

° in damp or wet areas

° where highly flammable liquids or

gases are present

° while in a tree or on a ladder

° while on aerial booms, buckets, or

platforms

Inspect tree before trimming or cut-

ting down. Make sure there are no

dead limbs or branches that may fall

on you. Make allowance for branches

to fall freely to the ground.

Use Right Tool

Use saw tor cutting wood only.

° Do not use chain saw for purpose not

intended.

° Do not use for cutting non-wood

items.

Dress Properly

1. Wear snug-fitting clothes when oper-

ating saw. Do not wear loose clothing

or jewelry. They can get caught in

moving saw chain.

2. Wear hair covering to contain long

hair.

Wear Safety Gear

Wear the tollowing safety gear when op-

erating saw:

° heavy-duty gloves (wear rubber

gloves when working outdoors)

° steel-toed safety footwear with non-

skid soles

° eye protection such as safety glasses,

goggles, or face screen

° safety hard hat

° ear mufflers or ear plugs

° face or dust mask (if working in

dusty areas)

Stay Alert

1. Watch what you ;=redoing. Use com-

mon sense. Do not operate saw when

you are tired.

2. Do not operate saw

° while under the influence of alcohol,

medication, or drugs

° while in a hurry

Check for Damage

Do not operate saw

° if pole or saw is damaged, adjusted

wrong, or not fully and securely

assembled

° if trigger does not turn saw on and

off. Chain must stop moving when

you release trigger. Have faulty

switch replaced by authorized ser-

vice center (see Teclmical Service).

WHILE OPERATING SAW

Keep Work Area Clean

1. Keep work area clean. Cluttered ar-

eas invite injuries.

2. Do not use near power lines. Keep

at least 10 feet away from electrical

lines.

3. If two or more persons perform buck-

ing and telling operations at the same

time, provide plenty of distance be-

tween operations. Provide distance of

at least twice the height of tree being

felled.

4. Secure wood you are cutting by using

clamps or chocks.

Keep Children, Bystanders, and

Animals Away

1. Only saw user should be in work

area. Keep bystanders 50 feet (15m)

away when operating saw.

2. Do not let visitors contact chain saw.

Use Right Tool

I. Do not use the polesaw to cut down

trees. Use the chain saw without

pole attachment and only if you are

trained or have expert help.

2. Do not cut small brush and saplings

with the polesaw. Use the chain saw

only, with extreme care. Slender mat-

ter may catch in the chain and be

whipped toward you. This could also

pull you off balance.

Stay Alert

1. Stay alert. Use common sense while

operating saw.

2. Grip chain saw firmly with both

hands. Never operate chain saw with

one hand. Never use hand guard as

handle.

3. Grip polesaw securely. Place one

hand on the pole and the other on the

handle.

4. Keep finger off trigger until ready to

make cut.

5. Before starting saw, make sure chain

is not touching anything.

6. To guard against electrical shock,

avoid body contact with grounded

objects such as pipes, fences, and

metal posts.

7. Keep all parts of body away from

chain when saw is running.

8. When cutting limb or tree trunk that

is under tension, use extreme caution.

Be alert tor wood springing back.

When wood tension is released, limb

could spring back and strike operator

causing severe iniury or death.

Do Not Force Saw While Cutting

Apply light pressure. It will do the job bet-

ter and safer at the rate for which it was

intended.

www. remingtonpowertoo/s, com 4

iMPORTANT SAFETY iNFORMATiON

Carrying Saw

Carry saw from one place to another

• with saw stopped

° with finger off trigger

° with guide bar and chain to rear

° Chain saw - by holding front handle

(never use hand guard as handle)

° Polesaw - with telescoping pole re-

turned to shortest position

° Polesaw - by holding the pole at the

balance point (close to saw end)

° Remove battery and use scabbard

when transporting saw.

_IL WARNING: This product con-

tains chemicals known to the State

of California to cause cancer or

birth defects, or other reproduc-

tive harm.

4BkWARNING: Some dust created

by power sanding, sawing, grind-

ing, drilling, and other construc-

tion activities contains chemicals

known (to the state of California)

to cause cancer, birth defects, or

other reproductive harm. Some

examples of these chemicals are:

• lead from lead-based

paints

• crystalline silica from

bricks and cement and

other masonry products

• arsenic and chromium

from chemically-treated

lumber

Your risk from these exposures

varies, depending on how often

you do this type ofwork. To reduce

your exposure to these chemicals:

work in awell ventilated area, and

work with approved safety equip=

merit, such as those dust masks

that are specially designed to filter

out microscopic particles.

KICKBACK

WARNING: Kickback may occur

when the nose or tip of the guide

bar touches an object, or when the

wood closes inand pinchesthe saw

chain inthe cut.Tip contact insome

cases may cause a lightning fast re-

versereaction, kickingthe guide bar

up and back towards the operator.

Pinching the saw chain along the

top of the guide bar may push the

guide bar rapidly back towards the

operator. Either of these reactions

may causeyou to losecontrol ofthe

saw which could result in serious

injury to user.

Kickback Safety Devices On This

Saw

This saw has a low-kickback chain and re-

duced kickback guide bar. Both items reduce

the chance of kickback. Low-kickback saw

chain is a chain which met the kickback

performance requirements of ANSI B 175.1.

Kickback can still occur with this saw.

Followassembly instructions onpage 11.Do

notremove front hand guard. Do notreplace

front hand guard with substitute.

The following steps will reduce the risk of

kickback.

, Use both hands to grip saw while saw

is running:

For chain saw, use both hands to grip

saw while saw is running. Use firm

grip. Thumbs and fingers must wrap

around saw handles.

For polesaw, use one hand to grip

the handle and the other hand to grip

the pole. Use firm grip. Thumbs and

fingers must wrap around pole and

handle.

, Keep all safety items in place on saw.

Make sure they work properly.

, Chain saw - do not overreach or cut

above shoulder height.

, Polesaw - do not overreach or extend

arms above shoulder height.

, Keep solid footing and balance at all

times.

, Stand slightly to left side of saw. This

keeps your body from being in direct

line with chain.

, Do not let guide bar nose touch any-

thing when chain is moving (see Figure

1).

, Never try cutting through two logs

at same time. Only cut one log at a

time.

, Do not bury guide bar nose or try

plunge cut (boring into wood using

guide bar nose).

, Watch for shifting of wood or other

forces that may pinch chain.

, Use extreme caution when reentering a

previous cut.

, Use low-kickback chain and guide bar

supplied with this chain saw. Only re-

place these parts with chains and guide

bars listed in this manual.

, Never use dull or loose chain. Keep

chain sharp with proper tension.

Saw Maintenance and Kickback

Safety

Follow maintenance instructions in this

manual. Proper cleaning ofsaw and chain and

guide bar maintenance can reduce chances

of kickback. Inspect and maintain saw af-

ter each use. This will increase the service

life of your saw. Note: Even with proper

sharpening, risk of kickback can increase

with each sharpening.

D rect ,-,n_on

_--_'i'_k\",._.DoNotLetGuide

chHere

90°

Quadrant t/2.)#

Figure I - Kickback Hazard Example:

Do Not Let Nose of Guide Bar Touch

Object While Chain is Moving

MAINTENANCE AND

STORAGE OF SAW

Disconnect Battery

Remove battery from saw

° when not in use

° before moving from one place to

another

° before tensioning saw chain

° before servicing

° before changing accessories or at-

tachments, such as saw chain and

pole.

Check for Damage

Inspect saw before and after each use.

• Check saw closely if guard or other

part has been damaged.

• Check for any damage that may af-

fect operator safety or operation of

saw.

• Check for alignment or binding of

moving parts.

• Check for broken or damaged parts.

Do not use saw if damage affects

safety or operation. Have dam-

age repaired by authorized service

center.

5 www. remingtonpowertools, com

iMPORTANT SAFETY iNFORMATiON

General Maintenance

Maintain saw with care.

• Never expose saw to rain.

° Keep chain sharp, clean, and lu-

bricated for better and safer

performance.

° Follow steps outlined in this manual

to sharpen chain.

° Keep handles dry, clean, and tree of

oil and grease.

° Keep all screws and nuts tight.

° Keep power cord on battery char-

ger away from heat, oil, and sharp

edges.

Service

When servicing, use only identical replace-

ment parts.

Storage

When not in use, always store saw

° with battery removed

° in a high or locked place, out of chil-

dren's reach

° in a dry place

° with scabbard over guide bar

• indoors

Save these instructions. It is your guide to

sate and proper operation of this saw.

POLESAW TRiMMiNG

PRECAUTIONS

Never stand directly under the limb

you are trimming. Always position

yourself out of the path of falling

debris.

Keep otherpersons away from cutting

end of polesaw and at a safe distance

from work area.

Do not use polesaw near cable, elec-

tric powerortelephone lines. Maintain

a minimum clearance of 10 feet from

all power lines.

Never stand on a ladder or other type

of unstable support while using the

polesaw.

Always use both hands to operate

polesaw. Keep a firm, steady pres-

sure on the polesaw while cutting but

do not try to force the saw through

the wood.

Do not use the polesaw to cut limbs

larger in diameter than the length of

the guide bar.

iMPORTANT: Read and understand

this manual before assembling or

operating this chain saw. improper

use of saw can cause severe in=

jury. Keep this manual for future

reference.

UNPACKING

1. Remove all items from carton.

2. Check all itemsforany shippingdam-

age. Ifyou find any damage orif any

partsare missing,promptly informdeal-

er where youbought chainsaw.

www. remingtonpowertoo/s, com 6

PRODUCT iDENTiFiCATiON

Rear Handle

Battery

Front Hand

Guard

Trigger

Handle

Batte/ry

CHAIN SAW

Saw

Handle Chain

Release ,\

Button

Guide Bar Nose

Guide

Bar

Sprocket

" Cover

_ ....... Power

...."Head

Battery Release

Button

Scabbard

Handle Release

Button

Trigger

Lockout

POLESAW

Hand Guard

Front "

Handle

Saw Chain

Battery Release

Handle Release

Button

Bar

.... Power Head

Trigger

Lockout

Clamping

Lever

Outer Pole

Inner Pole

Grip Area

Handle Release

Button

Battery Release

Button

Trigger

Button

iiiiiiiiiZ

iiiiiiiiiii_i!i

iiii@

,i,i,i,i,i,iZll¸

7 www. remingtonpowertoo/s, com

CHAIN SAW TERMS AND DEFiNITiONS

Bucking Process of cutting a felled tree

or log into lengths.

Felling Process of cutting down a tree.

Felling Cut Final cut when telling a tree.

Make this cut on opposite side of tree from

notching cut.

Front Handle Located at front of saw

body.

Front Hand Guard Shield between front

handle and guide bar. Protects left hand

while using saw.

Guide Bar Metal bar that extends from

saw body. The guide bar supports and

guides chain.

Guide Bar Nose Tip or end of guide

bar.

inner Pole The moveable section of tubing

to which the saw is attached.

Kickback Quick backward and upward

motion of guide bar. Kickback may occur

when tip of guide bar touches an object while

chain is moving. The guide bar will kick up

and back towards operator.

Limbing Process of cutting limb(s) from

a felled tree.

Low-Kickback Chain Chain that reduces

chance of kickback as required by ANSI

B175.1.

Normal Cutting Position Stance used

while making bucking and telling cuts.

Notching Cut Notch cut in tree that di-

rects fall of tree.

Outer Pole Retains the moveable inner

pole.

Power Head Chain saw without chain and

guide bar. Also known as saw body.

Pushback (Kickback, Pinch) Rapid

pushback of chain saw. Pushback may occur

if chain along top of guide bar is pinched,

caught, or contacts a ti)reign object.

Rear Handle Handle located at rear of

saw body.

Reduced Kickback Guide Bar Guide

bar that reduces chance of kickback.

Replacement Chain Chain that complies

with ANSI B 175.1 when used with a specific

saw. It may not meet ANSI requirements

when used with other saws.

Saw Chain (Chain) Loop of chain hav-

ing cutting teeth for cutting wood. The

motor drives chain. The guide bar supports

chain.

Spiked Bumper (Spike) Pointed teeth

at front of saw body beside guide bar. Keep

spiked bumper in contact with wood when

telling or bucking. It helps maintain position

of saw while cutting.

Sprocket Toothed wheel that drives

chain.

Switch Device that completes or interrupts

electrical circuit to motor of saw.

Switch Linkage This device connects

switch to trigger. It moves switch when you

squeeze trigger.

Trigger Lockout Device that reduces ac-

cidental starting of saw.

Trigger Device that turns saw on and off.

Squeezing trigger turns saw on. Releasing

trigger turns saw off.

Trimming (Pruning) Process of cutting

limb(s) from a living tree.

Undercut An upward cut from underside

of log or limb. This is done while in nor-

mal cutting position and cutting with top

of guide bar.

www. remingtonpowertoo/s, com 8

RECHARGEABLE BATTERY

PROTECTIVE BATTERY

TERMINAL CAP

_lb WARNING: Do not store or

carry battery so that metal objects

can contact exposed battery ter-

minals. For example, do not place

battery in aprons, pockets, tool

boxes, product kit boxes, drawers,

etc. with loose nails, screws, keys,

jewelry etc. without battery cap.

Aprotective battery terminal capisprovided

for use whenever the battery is out of the

tool or charger. Remove cap before placing

battery in charger or tool.

SAFETY WARNINGS

1. This manual contains important safe-

ty and operating instructions.

2. Before using battery charger, read all

instructions and cautionary markings

on battery charger, battery pack, and

product using battery pack.

_, CAUTION: To reduce the risk

of injury, charge only Remington

brand batteries. Other types of bat=

teries may burst causing personal

injury and damage.

3. Do not expose charger to rain or

snow,

4. Use of an attachment not recommended

or sold by Remington brand may result

in a risk of fire, electric shock, or injury

to persons.

5. To reduce risk of damage to electric

plug and cord, pull by plug rather than

cord when disconnecting charger.

6. An extension cord should not be used

unless absolutely necessary. Use of

improper extension cord could re-

sult in a risk of fire, electric shock or

electrocution.

a. Two-wire cords can be used with

2-wire or 3-wire extension cords.

Only round jacketed extension cords

should be used, and we recommend

that they be listed by Underwriters

Laboratories (U.L.). If the extension

is to be used outside, the cord must

be suitable tot outdoor use. Any cord

marked tk_routdoor use can also be

used tk_r indoor work. The letters

"W" or "WA" on the cord jacket

indicate that the cord is suitable tk_r

outdoor use.

b. An extension cord must have ad-

equate wire size (AWG or American

Wire Gauge) tk_rsafety, and to pre-

vent loss of power and overheating.

The smaller the gauge number of

the wire, the greater the capacity of

the cable; that is, 16 gauge has more

capacity than 18 gauge. When using

more than one extension to make up

the total length, be sure each exten-

sion contains at least the minimum

wire size.

(?HART FOR MINIMUM WIRE SIZE

(AWG) OF EXTENSION CORDS

NAMEPLATE RATING AMPS - 0

- 10.0

Cord AWG Cord

Length Size

25 feet 18 AWG

50 feet 18 AWG

100 feet 16 AWG

150 feet 14 AWG

7. Use only the supplied charger (P/

N 121397-01)when charging. The

use of any other charger could dam-

age the battery or create a hazardous

condition.

8. Use only one charger when charging.

9. Use only Remington RBISV OR

RBEI8V battery packs with this

product.

10. Do not attempt to open the charger.

There are no customer serviceable parts

inside. If damaged, call DESA Power

Tools Technical Service.

11. DO NOT incinerate the battery pack

even if they are severely damaged or

completely worn out. The batteries can

explode in a fire.

12. A small leakage of liquid from the

battery pack cells may occur under

extreme usage, charging, or tempera-

ture conditions. This does not indicate

a failure. However, if the outer seal is

broken and this leakage gets on your

skin:

• Wash quickly with soap and water.

• Neutralize with a mild acid such as

lemon juice or vinegar.

• If the battery liquid gets in your eyes,

flush them with clean water for a

minimum of 10 minutes and seek

immediate medical attention.

MEDICAL NOTE: The liquid is a

25-35% solution of potassium

hydroxide.

9 www. remingtonpowertools, com

RECHARGEABLE BATTERY

CHARGING BATTERY

The battery pack is not fully

charged at the factory. Before

attempting to charge the battery

pack, thoroughly read all Safety

instructions.

The charger is designed to use standard

household 120 volt 60 Hz power.

1. Plug cord from charger into charger

base. (See Figure 2)

Figure 2 - Plug Charger into Base

Plug the charger into any standard

120 Volt 60 Hz electrical outlet.

IMPORTANT" Do not charge by means

of an engine generator or DC power

source. Use only 120V AC.

Slide the charger onto the battery pack

as shown in Figure 3. The LED will

light up, Let the battery pack charge

until red LED turns off. At_ter the ini-

tial charge, under normal usage, your

battery pack should be tully charged in

3 to 9 hours.

4. Unplug charger. Remove the charger

by sliding off (See Figure 4).

5. Place the battery pack in the tool and be

certain that it is inserted tully into the

tool cavity until it "clicks" into place.

Figure 4 - Remove Charger

iMPORTANT CHARGING

NOTES

1. After normal usage, your battery

pack should be tully charged in 3 to 9

hours. If the battery pack is run-down

completely, it may take up to 9 hours

to become tully charged. Your battery

pack was sent from the factory in an

uncharged condition. For best perfor-

mance charge battery until red LED

turns off. Allow the battery to cool

down 30 minutes before charging after

using the saw. NOTE: A hot battery

placed in the charger will not charge.

2. DO NOT charge the battery pack in an

air temperature below 40°F (4,5 °C) or

above 105°F (40,5 °C). This is impor-

tant and will prevent serious damage to

the battery pack. Longest life and best

performance can be obtained if battery

pack is charged when air temperature

is about 75°F (24°(?).

3. While charging, the charger may hum

and become warm to touch. This is a

normal condition and does not indicate

a problem.

4. If the battery pack does not charge

properly

° Check current at receptacle by plugging

in a lamp or other appliance.

° Check to see if receptacle is connected

to a light switch which turns power off

when you turn out the lights.

° Move charger and battery pack to a

surrounding air temperature of 40°F

(4,5°(?) to 105°F (40,5 °C)

° If the receptacle and temperature are

OK, and you do not get proper charg-

ing contact DESA Power Tools.

5. The battery pack should be recharged

when it fails to produce sufficient

power on jobs which were easily done

previously. DO NOT CONTINUE us-

ing product with its battery pack in a

depleted condition.

6. To prolong battery life, avoid leaving

the battery pack on charger for ex-

tended periods of time (over 30 days

without use). Although overcharging is

not a safety concern, it can significantly

reduce overall battery life.

7. The battery pack will reach optimum

perti_rmance at'ter being cycled 5 times

during normal usage. There is no need

to run the batteries down completely

before recharging. Normal usage is

the best method of discharging and

recharging the batteries.

Figure 3 - Slid Charger onto

Battery

www. remingtonpowertoo/s, corn 10

CHAIN SAW INFORMATION

CHAIN SAW ASSEMBLY

_1= WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handling chain.

1. Align rib on chain saw power head with

groove in main handle (see Figure 5).

2. Slide power head into main handle until

units "snap" together (see Figure 6).

IMPORTANT."Both release buttons on

main handle must be fully engaged.

3. Slide battery onto main handle until

release buttons "snap" together (see

Figure 7).

Note: Fully charge battery before using

for first time. See Charging BatteJy.

Figure 6 - Assembled Power Head

Main Handle

Pull chain with light force 1/8" away

from bottom of guide bar and release

(see Figure 8). If chain lightly snaps

back into place, tension is correct.

A slight sag (1/16" or less) between

chain and bottom of guide bar is

acceptable.

NOTE: Your Remington Cordless Polesaw

and Cordless Chainsaw may have been

purchased together (as a 2-in-I polesaw/

chainsaw) or seperate (chainsaw only). If

the chainsaw was purchased separately, the

pole is available as an accessory and may be

purchased by visiting the "On-Line Outlet"

at www.desatech.com.

Groove

Rib /

Main

Handle

Power Head

Figure 5 - Align Power Head with

Handle

Battery

Figure 7-Assemble Battery onto Main

Handle

SAW CHAIN TENSION

_IL WARNING: Remove battery from

chain saw beforeadjusting sawchain

tension. Severe injury or death

could occur from body contact with

moving chain.

_k WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handling chain.

=I=

dl& WARNING: Maintain proper

chain tension always.AIoosechain

will increase the risk of kickback. A

loose chain may jump out of guide

bar groove. This may injure op-

erator and damage chain. A loose

chain will cause chain, guide bar,

and sprocket to wear rapidly.

Note: The saw chain tension is properly set at

the factory. A new chain will stretch. Check

new chain tension frequently (after discon-

necting battery) during the first 2 hours of

operation. Allow chain to cool down. Follow

steps below to check saw chain tension.

1. Remove battery from chain saw.

2. Place chain saw on a firm surface to

check chain tension.

Figure 8 - Check Chain Tension

Saw Chain Tension Adjustment

1. Loosen guide bar nuts before adjust-

ing chain (see Figure 9).

Guide BarNuts

Figure 9 - Loosen Guide Bar Nuts

2. Turn adjusting screw on front of

power head clockwise until slack is

out of chain (see Figure 10).

3. Wearing protective gloves, pull down

on chain to check chain tension (See

Step 3 Saw Chain Tension).

Screw

Figure 10- Turning Adjusting Screw

11 www. remingtonpowertoo/s, com

CHAIN SAW INFORMATION

4. Do not over-tension chain. Over-ten-

sioning will cause excessive wear and

will reduce the life of the guide bar

and chain. Over-tensioning also re-

duces the amount of cuts per battery

charge.

5. After chain tension is correct, tighten

guide bar nuts firmly (see Figure 11).

Trigger Lockout

Guide Bar

Nuts

Figure 11 - Tighten Guide Bar Nuts

OILING CHAIN

IMPORTANT" Applying oil to the chain and

guide bar reduces friction and excessive

wear. Improper oiling will cause excessive

wear and reduce the life of the chain and

guide bar.

1. Fill included squeeze bottle with

SAE #30 or #40 motor oil or bar

chain oil.

2. Apply several drops of oil between

chain and guide bar (see Figure 12.

Note: Oil should be applied before each

use and every 5 minutes during continu-

ous use.

Oil Chain

Frequently

Figure 12 - Applying Oil to Chain

CUTTING WITH THE CHAIN SAW

I. Attach battery to saw.

2. Make sure section of log to be cut is

not laying on ground. This will keep

chain from touching ground as it cuts

through log. Touching ground with

moving chain will dull chain.

3. Use both hands to grip saw. Always use

left hand to grip front handle and right

hand to grip rear handle. Use firm grip.

Thumbs and fingers must wrap around

saw handles (see Figure 13).

4. Make sure your footing is firm. Keep

feet apart. Divide your weight evenly

on both feet.

Trigger /

Figure 13 - Trigger Lockout and Trig-

ger Location

5. When ready to make a cut, press in

trigger lockout with right thmnb and

squeeze trigger (see Figure 13). This

will turn saw on. Releasing trigger

will turn saw off. Always turn saw on

before contacting saw chain with log.

6. When starting a cut, place moving

chain against wood. Hold saw firmly

in place to avoid possible bouncing or

skating (sideways movement) of saw.

7. Guide saw using light pressure. Do not

force saw. The motor will overload and

can burn out. It will do the job better

and safer at the rate for which it was

intended.

8. Remove saw from a cut with saw run-

ning. Stop saw by releasing trigger.

Make sure chain has stopped before

setting saw down.

9. Practice until you can maintain a

steady, even cutting rate.

FELLING A TREE (Cutting

Down a Tree)

_IL WARNING:

• Avoid kickback. Kickback

can result in severe injury or

death. See Kickback, page 5,

to avoid risk of kickback.

• Do not fell a tree without

ample skill or expert help.

• Keep children, animals, and

bystanders away from area

when felling a tree.

• If two or more persons

perform bucking and felling

operations at the same time,

provide ample distance

between operations. Provide

distance of at least twice the

height of tree being felled.

_IL WARNING: When felling atree,

be aware ofyour surroundings. Do

not endanger any person, strike

utility lines, or cause property

damage. If tree strikes utility lines,

contact utility company at once.

Felling is the process of cutting down a tree.

Make sure your ti)oting is firm. Keep feet

apart. Divide your weight evenly on both feet.

Follow directions below to tell a tree.

Before Felling a Tree

1. Beti)re telling, inspect tree. Make sure

there are no dead limbs or branches that

may fall on you. Study natural lean of

tree, location of larger branches, and

wind direction. This will help you

judge which way tree will fall.

2. Clear work area around tree.

3. Plan and clear a retreat path before

telling. Make retreat path opposite to

planned direction of fall of tree and at

45 ° angle (see Figure 14).

4. Remove dirt, stones, loose bark, nails,

staples, and wire from tree where you

will make telling cuts.

5. Stay on uphill side when telling tree.

Tree could roll or slide downhill after

falling.

45_o_= ....

" _R_etreat_at h Tree

Figure 14 -Retreat Path From Tree

www. remingtonpowertoo/s, corn 12

CHAIN SAW INFORMATION

Felling Procedure

A) Felling Notch

A properly placed felling notch will deter-

mine direction tree will fall. Place felling

notch on side of tree in direction you want

tree to fall (see Figure 15).

Follow directions below to create a felling

notch.

1. Make lower notch cut as close to

ground as possible. Hold saw so guide

bar is horizontal. Cut 1/3 the diameter

of tree trunk (see Figure 15). Note:

Always make this horizontal lower

notch cut first. If you make this cut

second, tree can pinch chain or guide

bar.

2. Start upper notch cut the same distance

above first cut as first cut is deep.

Example: If lower notch cut is eight

inches deep, start upper notch cut eight

inches above it. Cut downward at 45°

angle. The upper notch cut should meet

end of lower notch cut (see Figure

15).

3. Remove tree trunk wedge created by

notching cuts,

Direction of Fall

2" T

3rd Cut -

Felling Cut

,'1 st Cut -

] Lower

2" i Notch

Figure 15 - Felling A Tree

B) Felling Cut

1. Make felling cut two inches higher than

lower notch cut and on opposite side of

tree (see Figure 15). Keep telling cut

parallel to lower notch cut.

2. Cut towards notch.

3. As felling cut nears hinge, tree should be-

gin to fall. Note: If needed, drive wedges

into felling cut to control direction of fall.

If tree settles back and pinches chain,

drive wedges into felling cut to remove

saw. Only use wedges made of wood,

plastic, or aluminum. Never use wedge

made of steel. This could cause kickback

and damage to chain.

4. When tree begins to fall, quickly

• remove saw from telling cut

• release trigger to turn saw off

• put saw down

• exit area using retreat path

a'k

WARNING: Do not cut all the

way through tree. Leave about

two inches of tree diameter uncut

directly behind felling notch (see

Figure 15). This uncut portion acts

as a hinge. The hinge helps keep

tree from twisting and falling in

wrong direction.

_lb WARNING: Be alert for failing

overhead limbs. Watch your footing

while exiting area.

LIIVIBING A TREE

WARNING: Avoid kickback.

Kickback can result in severe injury

or death. See Kickbackto avoid risk

of kickback.

_IL WARNING: When cutting limb

that is under tension, use extreme

caution. Be alert for wood spring-

ing back. When wood tension is

released, limb could spring back

and strike operator causing severe

injury or death.

Limbing is removing branches from afallen

tree. Make sure your fk)oting is firm. Keep

feet apart. Divide your weight evenly on both

feet. Do not remove larger limbs under tree

that support log off ground. Remove each

limb with one cut (see Figure 16). Clear cut

limbs from work area often. This will help

maintain a sate work area.

Make sure you start your cut where limb

will not pinch saw during cutting. To avoid

pinching, start cut on freely hanging limbs

from above limb. Start cut on limbs under

tension from under limb. If pinch occurs, turn

saw off, lift limb, and remove saw.

Figure 16- Limbing A Tree

iiiiiiiiiZ

iiiiiiiiiii i!i

iiii@

iiiiiiZll¸

13 www. remingtonpowertoo/s, cam

CHAIN SAW INFORMATION

BUCKING A LOG

_I, WARNING: Avoid kickback.

Kickback canresult insevere injury

or death. See Kickback to avoid

risk of kickback.

WARNING:

• If on slope, make sure log

will not roll down hill. Secure

log by using wooden stakes.

Drive wooden stakes into

ground on downhill side of

log. Stand on uphill side of

log while cutting. Log may

roll after cutting.

• Never try cutting through

two logs at same time. This

could increase the risk of

kickback.

• While cutting log, never hold

log with your hand, leg, or

foot.

• While cutting log, never

allow another person to hold

log.

• Turn off and unplug saw

before moving from one

place to another.

Bucking a log is ctuting a log inlo sections.

Make sure your footing is firm. Keep feet apart.

Divide your weight evenly on both feet. When

possible, raise log or section off ground. Do

this by using limbs, logs, chocks, etc.

When cutting through log, maintain control by

reducing cutting pressure near end of cut. Do

not relax your grip on chain saw handles. Do

not let moving chain touch ground. Ground

will dull moving chain. After cutting through

log, release trigger to turn saw off before

moving saw.

Follow directions below to buck a log.

Entire Length Of Log On Ground

Cut log from top (see Figure 17).

Log Supported On One End

1. Make frst cut on underside of log (see

Figure 18). Use top of guide bar to

make this cut. Cut 1/3 through diameter

of log. This cut will keep section from

splintering when cut.

2. Make second cut directly above first

cut. Cut down to meet first cut. This

cut will keep log from pinching guide

bar and chain.

Figure 18 - Bucking Log When Log is

Supported On One End

Log Supported On Both Ends

1. Make first cut from above log (see

Figure 19). Cut 1/3 through diameter

of log. This cut will keep section from

splintering when cut.

2. Make second cut on underside of log,

directly under first cut. Use top of guide

bar to make this cut. Cut up to meet first

cut. This will keep log from pinching

guide bar and chain.

Figure 19 - Bucking Log When Log Is

Supported On Both Ends

TRIMMING ATREE (PRUNING)

WARNING: Avoid kickback.

Kickback can result in severe

injury or death. See Kickback to

avoid risk of kickback.

WARNING: Do not extend 1

arms above shoulders when us-

ing polesaw.

CAUTION: Seek professional

help if facing conditions beyond

your ability.

Trimming a tree is the process of cutting

limbs from a living tree. Make sure your

tix)ting is firm. Keep feet apart. Divide your

weight evenly on both feet. Follow directions

below to trim a tree.

1. Make first cut six inches from tree trunk

on underside of limb. Use top of guide

bar to make this cut. Cut 1/3 through

diameter of limb (see Figure 20).

2. Move two to four inches farther out

on limb. Make second cut from above

limb. Continue cut until you cut limb

off.

3. Make third cut as close to tree trunk as

possible on underside of limb stub. Use

top of guide bar to make this cut. Cut

1/3 through diameter of stub.

4. Make tk_urthcut directly above third cut.

Cut down to meet third cut. This will

remove limb stub.

2nd Cut - Pruning

4th Cut- Final Cut (toavoid

StubCut pinching)

t Stb

(toavoid splintering)

Figure 20 - Cutting A Limb

Figure 17- Bucking Log With Entire

Length On Ground

www. remingtonpowertools, corn 14

POLESAW INFORMATION

POLESAW ASSEMBLY

_k WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handling chain.

Remove battery from chain saw.

Separate main handle from chain saw

power head by pressing both release

buttons on main handle and pulling

apart (see Figure 21).

Press

Release Release

Button

Buttons

Figure 21 - Separate Main Handle from

Powerhead.

3. Align rib on chain saw power head with

groove in power head adapter on pole

(see Figure 22).

Groove

Power Head "

Polesaw

Power Head

Adapter

Figure 22 =Align Power Head with Power

Head Adapter

Slide power head into power head

adapter until units "snap" together (see

Figure 23). IMPORTANT" Both release

buttons on power head adapter must be

fully engaged.

Figure 23 - Assembled Power Head and

Power Head Adapter

5. Align rib on handle adapter on pole

with groove in main handle (see Figure

24).

Groove

Rib/_

\\\\\

Polesaw \,

Handle"-\

Adapter

Main Hdhdle

Figure 24 =Align Main Handle wfh Ham

die Adapter

6. Slide main handle into handle adapter

until units "snap" together (see Figure

25). IMPORTANT: Both release but-

tons on main handle must be fully

engaged.

Figure 25 -Assembled Main Handle and

Handle Adapter

7. Slide battery onto main handle until

release buttons "snap" together (see

Figure 26).

Note: Fully charge battery beti)re using

tk)r first time. See Charging Battery,

page 10

Figure 26 - Assembled Battery onto Main

Handle

ADJUSTING POLE LENGTH

The Remington brand polesaw has a tele-

scoping pole assembly that will extend from

47 inches (fully retracted) to 83 inches (fully

extended). A cam levered collet is used to

hold the pole in position at any extended

length.

1. To extend the pole, loosen the clamping

lever (see Figure 27). Pole will slide

freely.

2. Pull inner pole section out to desired

length of extension. Note: Only extend

pole to minimum length required to

reach limb that is being cut.

3. To lock pole in position, tighten clamping

lever (see Figure 27).

UNLOCK LOCK

Figure27 -Extending TelescopicPole

CUTTING WITH THE POLESAW

I. Attach battery to saw.

2. Use both hands to grip polesaw. Use

only designated grip areas when oper-

ating polesaw (see Figure 28). Use firm

grip. Thumbs and fingers must wrap

around polesaw handle and pole.

3. Make sure your ti_ofing is firm. Keep

feet apart. Divide your weight evenly

on both feet.

Figure 28= Designated Grip Areas

4. When ready to make a cut, press in

trigger lockout and squeeze trigger (see

Figure 29). This will turn polesaw on.

Releasing trigger will turn polesaw off.

Make sure saw is running beti_re starting

a cut.

5. When starting a cut, place moving

chain against wood. Hold polesaw

firmly in place to avoid possible bounc-

ing or skating (sideways movement) of

saw.

6. Guide polesaw using light pressure. Do

not ti_rce saw. The motor will overload

and can burn out. It will do the job bet-

ter and safer at the rate for which it was

intended.

7. Remove polesaw from a cut with saw

running, at full speed. Stop polesaw by

releasing trigger. Make sure chain has

stopped before setting polesaw down.

Trigger

Trigger Lockout

Figure 29- Polesaw Handle with Trigger

Lockout

15 www. remingtonpowertoo/s, com

CLEANING AND MAINTENANCE

NOTICE: Below are instructions

for servicing your chain saw. Any

servicing not mentioned below

should be done by an authorized

service center,

CLEANING SAW BODY

_, WARNING: Remove battery

from chain saw before servicing.

Severe injury or death could oc-

cur from body contact with mov=

ing chain.

_lb WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handling chain.

_, WARNING: When cleaningsaw

body,

• do not submerge saw in

any liquids

• do not use products

that contain ammonia,

chlorine, or abrasives

• do not use chlorinated

cleaning solvents, carbon

tetrachloride, kerosene,

or gasoline

Normal Guide Bar Maintenance

1. Remove guide bar from chain saw.

2. Remove sawdust from guide bar

groove periodically. Use putty knife

or wire (see Figure 31 ).

3. Clean oil slots after each day of use.

4. Remove burrs from sides of guide

bar. Use flat file to make side edges

square.

Replace guide bar when

• bar is bent or cracked

, inside groove of bar is badly worn

Note: When replacing guide bar, see

Replacement Parts" and Accessories for

replacement in%rmafion. See Parrs"Lis %r

correct bar.

/ Burr

FlatFile J'J

Guide

Bar

Cleaning Groove With

f Putty Knife

Oil Slot

Figure 31 - Guide Bar Maintenance

Keep saw body clean. Use a soft cloth damp-

ened with a mild soap and water mixture.

Wipe saw body to clean.

CARE OF GUIDE BAR

Groove

Guide Bar

/ J

Normal Guide

Bar

Uneven bar wear causes most guide bar prob-

lems. Incorrect sharpening of chain cutter

and depth gauge settings often cause this.

When bar wears unevenly, it widens guide

bar groove (see Figure 30). This causes chain

clatter and rivet popping. Saw will not cut

straight. Replace guide bar if this occurs.

Inspect guide bar before sharpening chain.

A worn or damaged guide bar is unsafe. A

worn or damaged guide bar will damage

chain. It will also make cutting harder.

Guide Bar

Guide Bar With

Uneven Wear

Figure 30 - Guide Bar Cross Section

Showing Uneven Bar Wear

SHARPENING SAW CHAIN

_lh WARNING: Remove battery

from chain saw before servicing.

Severe injury or death could oc-

cur from body contact with mov=

ing chain.

WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handling chain.

Keep chain sharp. Your saw will cut faster

and more safely. A dull chain will cause

undue sprocket, guide bar, chain, and motor

wear. If you must force chain into wood and

cutting creates only sawdust with few large

chips, chain is dull.

items Needed to Sharpen Chain

Purchase these items from your local

dealer, hardware store, or chain saw sup-

plies outlet.

° 5/32" round file

• Depth gauge tool

• File guide

• Vise

• Medium sized flat file

Sharpening Cutters

Use file guide tk_r30° filing.

1. Adjust chain tier proper tension (see

Saw Chain Tension, page 11).

2. Clamp guide bar in vise to hold saw

steady. Note: Do not clamp chain.

3. Press 5/32" round file (attached to file

guide) into groove between top plate and

depth gauge on chain. File guide should

rest on both top plate and depth gauge

(see Figure 32). Note: File at midpoint

of guide bar.

..... _/_Filing Direction

....... File Guide

30 ° Guide Mark

/32" Round

File

Note:This illustration shows file guide placement

and filing direction for sharpening cutters on left

side of chain.

Figure 32 - File and File Guide Place-

ment on Chain

4. Hold file guide level. Make sure 30°

mark on file guide is parallel to cen-

ter of guide bar (see Figure 33). This

will insure that you file cutters at 30°

angle.

5. File from inside towards outside of

cutter until sharp. Only file in this one

direction (see Figure 33). Note: Two or

three strokes with file should sharpen

cutter.

6. After each cutter is sharpened, move

chain R_rward to sharpen next cutter.

File all cutters on one side of chain.

7. Move to other side of chain and repeat

process.

Depth Gauge (left

side of chain) ,,

Groove ..

Top Plate (left ",_......

side of chain)

Depth Gauge (right

side of chain)

Groove

TopPlate(right

sideofchain)

Right Sideof Chain

Figure 33 - Chain Part Locations

www. remingtonpowertoo/s, corn 16

CLEANING AND MAINTENANCE

Filing Cutter Depth Gauges

The cutter depth gauge clearance is reduced as

cutters are sharpened. After every second or

third sharpening, reset culter depth gauges.

1. Place depth gauge tool (.025") firmly

across top of two cutters. Make sure

depth gauge enters slot in depth gauge

tool (see Figure 34).

2. Use medium flat file. File depth gauge

level with depth gauge tool.

3. Remove depth gauge tool. With flat file.

round off front corner of cutter depth

gauge (see Figure 35).

After several hand filings, have authorized

service center or sharpening service machine

sharpen chain. This will insure even filing.

REPLACING SAW CHAIN

_IL WARNING: Remove battery

from chain saw before adjusting

saw chain tension. Severe injury

or death could occur from body

contact with moving chain.

_, WARNING: Cutting edges on

chain are sharp. Use protective

gloves when handJing chain.

IMPORTANT: Do not clamp chain-

saw in vise to replace saw chain or

guide bar.

Sprocket

GuideBarBolts

SawChain

// Adjusting

//' Hole

Guide Bar

Depth Gauge

Flat File

Depth Gauge

Tool ....

Figure 34 - Depth Gauge Tool On

Chain

Front

.025"

Figure 35 - Round Off Front Corner Of

Depth Gauge

Replace chain when cutters are too worn

to sharpen or when chain breaks. Only use

replacement chain noted in this manual.

Always include new drive sprocket when

replacing chain. This will maintain proper

driving of chain. Note:Forproperchain and

drive sprocket, see Parrs"List.

Refer to Figure 36 while completing the

following steps.

I. Loosen and remove guide bar nuts.

2. Remove sprocket cover.

3. Remove saw chain.

4. Place new chain around drive sprocket,

along top groove of guide bar, and around

guide bar nose. Note: Make sure cutting

edges of chain are facing in right direction.

Position chain so cutting edges on top of

guide bar face guide bar nose (see Figure

37 and indicator on side cover of saw).

5. Before placing sprocket cover onto guide

bin"bolts, verity that the adjusting nib is

in the adjusting hole on the guide bar.

6. Place sprocket cover onto guide bar

bolts.

7. Thread guide bar nuts onto guide bar bolts.

IMPORTANT: Finger tighten only.

8. Adjust chain tension. Follow steps under

Saw Chain Tension, page 12).

9. Securely tighten guide bar nuts with

wrench.

Adjusting Nib Guide Bar Nuts

Sprocket Cover

Figure 36- Guide Bar and Saw Chain

Replacement

Cutting Edges

Figure 37- Correct Installation of Saw

Chain

4Bk CAUTION: Do not pJace chain

on saw backwards. If chain is back-

wards, saw will vibrate badly and

will not cut.

Co1_:h_ued

17 www. remingtonpowertoo/s, com

STORAGE

If storing saw for more than 30 days, follow

steps below.

1. Remove battery from chain saw.

2. Charge battery completely. Note: It

could take up to 9 hours to complete-

ly charge the battery.

3. When battery is completely charged,

remove from charger and put protec-

tive cap on battery terminals.

IMPORTANT."To prolong battery life,

avoid leaving battery on charger for

extended periods of time (over 30

days without use).

4. Remove and clean guide bar and

chain. (?lean guide bar and chain by

soaking in petroleum based solvent

or mild soap and water mixture.

5. Dry guide bar and chain.

6. Place chain in container filled with

oil. This will prevent rust.

7. Wipe a thin coating of oil over sur-

face of guide bar.

8. Wipe off outside of saw body. Do this

with soft cloth dampened with a mild

soap and water mixlure.

9. Store chain saw and battery

* in a high or locked place, out of chil-

dren' s reach

* in a dry place

* in a carrying case or with scabbard over

guide bar

TECHNICAL SERVICE

You may have further questions about assem-

bling, operating, or maintaining this product.

If so, you can visit our Technical Service web

site at www.remingtonpowertools.com or

contact our Technical Service Department

at 1-800-626-2237 (English Only). You may

also write to:

DESA Power Tools

P.O. Box 90004

Bowling Green, KY 42102-9004

ATTN: Technical Service

When contacting DESA Power Tools, have

ready:

, Your Name

, Your Address

, Your Phone Number

, Model Number of Product

, Date of Purchase (Include copy of re-

ceipt for written requests).

REPLACEMENT PARTS

AND ACCESSORIES

4B& WARNING: Use only replace=

merit parts and accessories de=

scribed in this manual. Use of other

parts or accessories could damage

saw or injure operator.

For original replacement parts and acces-

sories, contact your nearest Authorized

Dealer or Authorized Service (?enter tierthis

product. If they can not supply the part or

accessory, contact your nearest Parts Central

listed on page 45. Each Authorized Dealer,

Authorized Service Center, and Parts Central

is independently owned and operated. You

may also order parts from the "Online Outlet"

at www.remingtonpowertools.com.

See pages 43 through 44 for an Illustrated

Parts List.

If you need additional referral information,

contact our Technical Service Department

(see TechMcal Service).

REPAIR SERVICE

Note: Only use original replacement parts.

This will protect your warranty coverage ti)r

parts replaced under warranty.

WARRANTY SERVICE

If product requires warranty service, return

it to nearest Authorized Service (?enter.

You must show proof of purchase. If faulty

materials or workmanship caused damage,

we will repair or replace product without

charge. Note: Normal wear, misuse, abuse,

neglect, or accidental damage is not covered

under warranty.

NON-WARRANTY SERVICE

If product requires service, return it to nearest

Authorized Service (?enter. Repairs will be

billed to you at regular repair list prices.

For additional Service Center or warranty

information, call 1-800-626-2237 or visit

our Technical Service web site at www.

remingtonpowertools.com.

We reserve the right to amend these

specifications at any time without notice.

The only warranty applicable is our standard

written warranty. We make no other

warranty, expressed or implied.

BATTERY DISPOSAL AND

RECYCLING

This product uses nickel-cadnium bateries.

Local, state, or federal laws may prohibit

disposal of nickel-cadnium batteries in the

ordinary trash.

To help protect the environment and con-

serve natural resources, please dispose of

batteries properly. You may contact your

local recycling center for inti)rmation on

where to drop off the batteries.

www. remingtonpowertoo/s, corn 18

TROUBLESHOOTING

_ote. For additional help, v=sltDESA Power Tools' techmcal service web site at www.remingtonpowertools.com. i

WARNING: Remove battery from chain saw before adjusting saw chain tension. Severe injury or death could oc-

cur from body contact with moving chain.

O; " D ' '@ ;

Saw runs. but does not cut 1. Chain assembled backwm'ds on 1. See Replacing Saw Chain

guide bar,

I. Chain is dull, I. See Sharpening Saw ChainSawdoes not cut unless heavily forced.

Cutting produces only sawdust with

few large chips

Saw runs slow. Saw stalls easily

Motor of saw does not run when you

squeeze trigger

Motor of saw runs, but chain does

not move

Chain comes oft"guide bar

Batter3' dies quickly

Battery not charging

1. Battery is nemly depleted

1. Battery not installed properly,

2. Battery not chaged,

3. Trigger lockout not pressed in to

release trigger,

4. Worn out motor brushes,

5. Open wiring circuit on saw

1. Gear train failure

1. Chain is loose

2. Guide bar and chain not

assembled correctly

I. Battery not fully charged

2. Chain tension too tight

3. Old battery that does not hold

charge.

l. Charger not plugged in

2. Charger cord not plugged into

charger base

3. Battery not fully inserted into

charger base.

4. Battery is too hot Iron] use.

t. Recharge battery completely

until red LED turns oft.

1. Verify battery is installed

properly,

2, Check batteu charging

requirements.

3. Press in trigger lockout before

squeezing trigger,

4. Contact DESA Power Tools

Technical Service.

5, Contact DESA Power Tools

Technical Service.

I. Contact DESA Power Tools

Technical Service.

1. Tighten chain. See Saw Chain

Tension

2. See Replacing Saw Chain

1. Recharge battery completely

2. See Saw Chain Tension and

Adjusting Saw Chain Tension

3. Replace battery

1. Plug charger into 120V 60HZ

AC source

2. Ensure charger cord is fully

inserted into charger base.

3. Slide battery fully into chm'ger

base

4. Allow battery to cool for 30

minutes before placing in the

charger.

rrl

ffJ

3::

19 www. rem/t)gtot)poweitools, corn

WARRANTY iNFORMATiON

REMINGTON BRAND 1BV CORDLESS POLESAW/CHAIN SAW

LiMiTED WARRANTIES

NEW PRODUCTS

Standard Warranty

DESA PowerToolswarrants this new product and any parts thereof to be free from defects in material and workmanship fbr a period of two

(2) years from the date of first purchase from an authorized dealer provided the product has been maintained and operated in accordance with

DESA Power Tools' warnings and instructions.

Standard Warranty Battery

DESA Power Tools warrants this new battery and any parts thereof to be free from defects in material and workmanship fbr a period of six

(6) months from the date of first purchase from an authorized dealer provided the product has been maintained and operated in accordance

with DESA Power Tools' warnings and instructions.

FACTORYRECONDITIONED PRODUCTS

Limited Warranty

DESA Power Tools warrants factory reconditioned products and any parts thereof to be free from detects in material and workmanship ti__r90 days from the

date of first purchase from an authorized dealer provided the product has been installed, maintained and operated in accordance with DESA Power Tools'

warnings and instructions.

TERMS COMMON TO ALL WARRANTIES

The fbllowing terms apply to all of the above warranties:

" Always specify model number when contacting the manufacturer. To make a claim under this warranty the bill of sale or other proof of

purchase must be presented.

- This warranty is extended only to the original retail purchaser when purchased from an authorized dealer.

- This warranty covers the cost of part(s) required to restore this product to proper operating condition and an allowance fbr labor when

provided by a DESA Power Tools Authorized Service Center. Warranty parts must be obtained through authorized dealers of this product

and/or DESA Power Tools who will provide original fhctory replacement parts. Failure to use original f:actory replacement parts voids this

warranty.

" Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty repairs, unless expressly covered by

this warranty, are not reimbursable under this warranty and are the responsibility of the owner.

" Excluded from this warranty are products or parts that f:ail or become damaged due to misuse, accidents, lack of proper maintenance,

tampering, or alterations.

" Excluded from this warranty are products purchased fbr commercial, industrial or rental usage.

- This is DESA Power Tools'exclusive warranty, and to the full extent allowed by law; this express warranty excludes any and all other warranties,

express or implied, written or verbal and limits the duration of any and all implied warranties, including warranties of merchantability and

fitness fbr a particular purpose to two (2) years on new products, six (6) months on battiers and 90 days on fhctory reconditioned products

from the date of first purchase. DESA Power Tools makes no other warranties regarding this product.

" DESA Power Tools'liability is limited to the purchase price of the product, and DESA Power Tools shall not be liable fbr any other damages

whatsoever under any circumstances including indirect, incidental, or consequentiM damages.

" Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

" %fis warranty gives you specific legal rights, and you may also have other rights which wiry from state to state.

For information about this warranty contact:

ESA

POWER TOOLS

P.O. Box 90004

Bowling Green, KY 42102-9004

www.remingtonpowertools.com

1-800-626-2237 (English Only)

Model

Date Purchased

www. remingtonpowertools, corn 20

Page is loading ...

Remington BPS188A Owner's manual

Brand: Remington

Model: BPS188A

Category: Power chainsaws

Type: Owner's manual

This manual is also suitable for

BS188A

Download PDF

report

in other languages

español: Remington BPS188A El manual del propietario

Remington BPS188A Owner's manual

This manual is also suitable for

Remington BPS188A Owner's manual

in other languages

Related papers

Other documents