audiophony DJ inn Pro Owner's manual

Brand: audiophony

Model: DJ inn Pro

Category: DJ controllers

Type: Owner's manual

This manual is also suitable for

DJinn PRO

Page is loading ...

Multimedia platf

orm for mixing and playback

OPERATING INSTRUCTION

Djinn Pro - Multimedia platform for mixing and playback

1 - Safety Instructions

IMPORTANT symbol indicates an

important recommendation for use.

The CAUTION symbol indicates a risk of product deg-

radation.

The WARNING symbol indicates a risk of harm to the physical integrity of the

user and any other person present.

Important Safety Information

The product can also be damaged.

Symboles utilisés

Only the relevant technical services and recognized

by HITMUSIC are authorized to perform maintenance

on this unit. Routine maintenance actions must follow

the precautions in this manual

This device contains within its housing, uninsulated

portions under tension high enough to pose a risk of

electric shock. Do not under any circumstances per -

form maintenance on this unit when it is turned on.

This unit was created to operate in place heated and

insulated from any form of moisture or water spray.

Any use in wet locations, unprotected, or subjected to

temperature changes represent a significant low risk

to both the device for anyone nearby.

CAUTION : To reduce the risk of electric shock, never remove

the covers. There are no user-serviceable parts inside. Contact a

qualified service technician for maintenance of this unit.

Noise levels

The sound systems are capable of delivering

a sound level (SPL) harmful to human health.

The sound pressure levels are apparently

noncritical damage hearing if the person is

exposed over a long period.

Do not park close to the speakers in operation.

Risk of electrocution

To prevent electric shock, do not use

extension cord, power strip or other system

without connecting metal parts in contact are

completely out of reach.

Environmental Protection

• Your product is composed of materials to be recycled, do not throw in your trash, bring it to a collection center set up

near your residence. The service centers you will resume your device at the end of life to proceed to its destruction in

compliance with environmental rules.

• For more information http://www.hitmusic.fr/directives-deee.php.

• The environment is a cause that defends HITMUSIC, we sell only the products fit, conform to ROHS.

Page 2

Djinn Pro - Multimedia platform for mixing and playback

Instructions and recommendations

1 - Read the instructions :

It is advisable to read all instructions and operating instructions

before using the device.

2 - Retain instructions :

It is advisable to keep the instructions for use and operation

later.

3 - Consider the warnings :

It is advisable to carefully consider all warnings and

instructions for operating the product.

4 - Follow the instructions :

It is recommended that you follow all operating instructions

and use.

5 - Water and moisture :

Do not use near water, for example near a bathtub, sink or

basin, or in a damp place or near a swimming pool, etc.. ..

6 - Installation :

Do not place this product on a rolling stand, tripod, bracket

or table. The product may fall seriously injuring a child or

an adult and seriously damaged. Use only a cart, stand,

tripod, bracket or table recommended by the manufacturer

or sold with the apparatus. In any case to

install the equipment it is advisable to follow

the manufacturer's instructions and use

instruments recommended by it.

It is strongly advised to move with caution

when rolling the cabinet the unit is over. Quick stops, excessive

pushing and rough surfaces might topple the whole.

7 - Mount on a wall or ceiling :

It is recommended that you contact your dealer prior to

installation.

8 - Air exit :

Slots and openings in the cabinet are provided for ventilation,

to ensure use of the product with confidence and to avoid

overheating. These openings must not be blocked or covered.

We must be careful to never block the openings by placing the

product on a bed, sofa, rug or other surface of this style. This

device should not be placed in an enclosed facility

such as a bag or rack unless aeration was provided

or the manufacturer's instructions were followed.

9 - Heat :

It is advisable to keep the product away from heat sources

such as radiators, stoves, heat reflector or other products

(including amplifiers) that produce heat.

10 - Power supply :

This product works only on the voltage on a label

on the back of the product. If you are unsure of the

voltage of your electrical installation, consult your

dealer or local power company.

11 - Protection of Electrical cables:

You must ensure that electrical cables are not likely

to be walked on or pinched by items placed upon

or against, paying particular attention to plugs and

their exit point on the unit.

12 - Cleaning :

Unplug the unit before cleaning. Do not use attachments not

recommended by the manufacturer. Use a damp cloth on the

surface of the device. Do not pass the apparatus underwater.

13 - Period of no use :

Unplug the power cord of your appliance if you do

not use it for a long period.

14 - Penetration by objects or liquids :

Do not enter into any kind of objects into this

product through openings as they may cause fire

or electric shock.

Never spill liquid of any kind on the product.

15 - Damage requiring service :

Ask qualified persons in the following cases:

- When the power cord or plug is damaged (e).

- If liquid has been spilled or objects have fallen

into the apparatus.

- If the product has been in contact with rain or

water.

- If the product does not operate normally by

following the instructions.

- If the product took a shock.

16 - Maintenance / overhaul :

Do not attempt to review this product yourself.

This will expose you to dangerous voltage. Talk to

qualified personnel.

17 - Operating environment :

Temperature and humidity environment Operating:

5-35 °, relative humidity below 85% (vent not

blocked).

Do not install the unit in a poorly ventilated area or

in a place subject to high humidity or direct sunlight

(or strong artificial light)

Page 3

Auto cue RCA output

Pitch display Skid Effect

Real time cue Filter Effect

Folder Search Echo Effect

Fine Tune BPM Flanger Effect

Cross Fader Curve Relay Playback

Switching Power Supply Mp3 Track Listings

Real Time Scratch Play Fader Start Playback

2 External Phono/Line Input 1/75th second frame search

Plays Mp3's from either USB MIDI interface Controller for PC

Master Output through USB Port 3 Band Kill EQ for Each Channel

Jog Wheel Sensitivity Adjustment Jog Wheel Pitch Bend +/-100%

Mic Tone, Phones Cue Pan Control Headphone Jack with Level Control

4 Programmable Cue (Bank) Buttons Selectable Single or Continuous Play

Memory Backup, Defaults to last setting 8 different speed scan (4 Forward/4 Reverse)

Seamless Loop (uninterrupted loop playback)

Large bright VFD display can be viewed from wide angles

Adjustable Pitch Percentages: +/-6%, +/-10%, +/-16% & +16/-100%

Instant Start (sound is produced immediately when the PLAY button is pressed)

Djinn Pro - Multimedia platform for mixing and playback

2 - Features

3 - Controls and functions

Top pannel

Page 4

1. VFD DISPLAY – This high quality VFD display indicates all the functions, as they are occurring. The

display ICONS will be explained on VFD displaysection.

2. SEAMLESS LOOP

A BUTTON (IN BUTTON) – This function allows you to set a CUE POINT without music interruption.

This button also sets the starting point of a seamless loop.

B BUTTON (OUT BUTTON) – This button is used to set the ending point of a loop. A loop starting point

is set by pressing the A button. Pressing the B button set the loop ending point. The loop will continue

to play until the RELOOP button is pressed once again.

RELOOP BUTTON – If a SEAMLESS LOOP has been made, but the Player is not active in

SEAMLESS LOOP mode (a loop is not playing), pressing the RELOOP button will instantly reactivate

the SEAMLESS LOOP mode. To exit loop, press the RELOOP button.

IN/OUT POINT EDIT – In the LOOP mode, press B button, LED of B will flash an d display will show the

loop-out point time, now you can turn the jog wheel to edit OUT point. Then press the B button to exit

editing; or press the A button, LED of A will flash and “IN EDIT” will be indicated in the VFD, now you can

turn the jog wheel to edit IN point. Then press the A button to exit editing.

3. TRACK

OB – This knob has three functions as below:

The knob is used to select a track. Turning track knob will forward/backward skip to next track.

Holding down and turning track knob will rapidly forward/backward skip through the tracks by 10 tracks

per click.

Press track knob to switch file name/title /artist /Album/Genre on the VFD.

4. SAVE BUTTON – This button can be used in couple of ways as below:

Press this button to activate the save mode, the SAVE button LED will glow when active. After the save

mode is activated, press your desired bank button to store your CUE point or playing loop.

To store your loops and cue points that are saved in the BANKS to the system memory for next time,

press the SAVE button for 1 second and the button flashes.

RECALL MEMORY : The player can store 4 programmed cue points or loops per track in the USB

device. The memory points in the USB device are depending on available memory space. These setting

may be recalled at any time, even when an audio source has been removed and loaded at a later time.

To recall the bank memory with USB device as following:

Press the SAVE button, the button is lighted up, and turns the TRACK knob to select the TRACK with

BANKS that you would like to recall for a cue point; or a loop when in the loop mode (press the

RELOOP button to activate loop mode).

5. X (FX1) BUTTON – This button is used to adjust the parameter time value. You can push the X button

(FX1), LED on, and turn the JOG WHEEL to adjust the parameter time value. If the HOLD function is not

active, any changes to the effect parameters will be momentary.

6. SEARCH/REAL-TIME CUTTING AND EXTENDING LOOP FUNCTION BUTTONS

This search button allows you to quickly scan backwards through a track.

This search button allows you to quickly scan forwards through a track.

During the loop playback, press the SEARCH button, the loop playing time is cut in half each time the

button is pressed. The loop can be cut to 1/64 original loop length. Press the SEARCH button, the loop

playing time is doubled each time the button is pressed. The loop can be extended to 16X original loop length.

7. JOG MODE BUTTONS – The jog wheel has 3 effect functions as below:

CUE MODE:

IN PLAYBACK MODE

While in play mode and when the touch sensitivity function is active, the JOG WHEEL can be used to

return the unit to last IN point.

Simply touch the JOG WHEEL and unit will immediately return to the last set CUE point and playback

without music interruption.

IN CUE MODE

While in cue mode and when the touch sens itivity function is active, tapping on the JOG WHEEL can

be used to start playback.

The unit will continue to playback until the JOG WHEEL is released. Once the JOG WHEEL is

released the unit will return to the last IN point.

VINYL MODE – When wheel mode is set to VINYL, use the JOG WHEEL to activate the scratch effect

by touching the surface of Jog Wheel.

CLASSIC MODE – When wheel mode is set to CLASSIC, scratch mode is exit, JOG WHEEL can be

used to pitch bend and frame search.

Djinn Pro - Multimedia platform for mixing and playback

Page 5

8. JOG WHEEL –This wheel has three functions:

The jog wheel will act as a frame search control when the track in the pause or cue mode, allowing you to

set a point.

The wheel also works as a pitch bend during playback. Turning the wheel clockwise will increase the

pitch percentage up to 100%, and turning the wheel counterclockwise will decrease the pitch percentage

down to -100%. The pitch bend will be determined on how long you turn the jog wheel continuously.

The jog wheel can be used with the hold of the X(TIME) and Y(RATIO) buttons to set effects parameter

adjustment

9. CUE/ BUTTON – Pressing the button will activate the CUE PLAY function and the music will play instantly

from the last cue point.

10. CUE BUTTON – Pressing the CUE button during playback immediately

will pause playback and return the

track to the last set cue point; the CUE indicator will glow in the cue mode. The CUE button can be held

down to momentarily play the music. When you release the CUE button it instantly returns to the CUE

POINT. You can also tap the CUE button to create a STUTTER EFFECT.

11. PLAY/PAUSE BUTTON – Each press of the PLAY/PAUSE button causes the operation to change from play

to pause or from pause to play. While in play mode the PLAY/PAUSELED will glow and while in pause mode

the PLAY/PAUSE LED will flash.

12. TAP BPM BUTTON – This button is used to override and manually set a track BPM. Occasionally the built-

in BPM meter may not function as desired. This button allows you to override the internal beat clock and

manually set a track BPMs. To manually set the BPMs; tap this button a few times to a tracks heavy down

beat, the unit will automatically calculate your tapping and translate it into a tracks BPMs. The BPM

READOUT is then displayed in the VFD. You can also hold the TAP BPM button and turn the TRACK or

FOLDER knob to adjust the BPM value. To return to the automatic BPM counter, press and hold down the

TAP button for at least 1 seconds and then release.

13. PITCH BEND BUTTONS – The speed rises while the “+button” is pressed and returns to the original pitch

when the button is released. The speed drops when the “–button” is pressed and returns to the original

pitch when the button is released. These buttons can be used to synchronize the beats of 2 tracks.

14. PITCH SLIDER – This slider is used to adjust the playback pitch percentage. The slider is a set adjustment

and will remain set until the pitch slider is moved or the pitch function has been turned off.This adjustment

can be made with or without a music source device in the player. The pitch adjustment will remain even if a

music source device has been removed and will reflect on any other music source device inserted into the

player. That is to say, if you set a +6% pitch on one music source device, remove the USB device and

insert another, that music source device too will have a +6% pitch. The amount of pitchbeing applied will

be displayed in the VFD.

15. MASTER TONE – This button activates the KEY LOCK function. This function allows you to use the PITCH

SLIDER to speed up or slow down playback speed without altering the tonal pitch of the track.

16. PITCH RANGE SELECTOR – Press this button to choose any pitch range percentages of 6%, 10%, 16%

and +16/-100%.

17. PITCH ON/OFF BUTTON – This button is used to turn the PITCH SLIDER function on and off. The pitch

percentage can be changed between +/-6%, 10%, 16% and +16%/-100%. -100% will allow the least

amount of pitch manipulation and 16% will allow the most amount of pitch manipulation.

18. SOURCE SELECT BUTTON – This button lets you toggle between USB Port 1 and 2. In other words, you

can select which USB port will be activated and the relational LED will be lit. The function can only be

selected under pause mode.

19. FOLDER KNOB – Turn FOLDER knob to search the desired folder.

20. HOT CUE/LOOP BANK 1~4 – These buttons are used to store either four cue points or four loops. Each

Bank button can store either a loop or a cue point. When the SAVE LED is lit, press the desired BANK

button to set a cue point, LED lit red, or a loop and LED lit green. Press the desired BANK button to play

the music from the stored cue point instantly and the LED of the activated BANK button will be flashing.

21. EFFECTS AND HOLD BUTTON

ECHO EFFECT – This button is used to activate and deactivate the Echo effect. The Echo effect adds

an echo to your output signal.

FLANGER EFFECT – This button is used to activate and deactivate the FLANGER effect. The

FLANGER effect distorts the output signal and creates an effect similar to the frequency phasing in and

out of each other.

Djinn Pro - Multimedia platform for mixing and playback

Page 6

With Virtual DJ, this button allows the tempo sync of the two desks. this is the SYNC function.

HOLD BUTTON – This button allows you to lock any new parameter settings you set to the effects. The

button LED will glow when the hold function is selected. When the hold selection is not active, any

changes to the effect parameters will be moment.

FILTER BUTTON – This button is used to activate and deactivate the Filter effect. The Filter effect

tweaks the original sound to add different tonal definition. The effect is almost the same as the PHASE

effect.

SKID BUTTON – This button is used to activate and deactivate the Skid effect. The Skid effect

simulates the sudden platter stop of a turntable, like pressing the stop button on a turntable.

22. CLEAR BUTTON – Press CLEAR button, the button is lighted up, and then select the BANK buttons (1 ~ 4)

you would like to clear.

23. Y (FX2) BUTTON – This button is used to adjust the parameter ratio value. You can push the Y button and

turn the JOG WHEEL to adjust the parameter ratio value.

24. TIME BUTTON – The button will switch the time value described in the time meter between Elapsed

playing time and TRACK Remaining time.

25. SGL/CTN – This function allows you to choose between single track play and continuous track play (all

tracks in order). With this button you can also switch AUTO CUE on and off, by pressing it for at least 1

second.

1. MIC 1 JACK – This jack is used to connect a microphone to the mixer. Connect your microphone via 1/4

inch jack. The volume output level for microphone will be controlled by its own respective VOLUME KNOB.

2. MIC LEVEL CONTROL – These rotary knobs control the output volume of MICROPHONE 1/2. However,

master volume is controlled by the MASTER VOLUME CONTROL.

3. MIC TONE CONTROL – This rotary knob control the frequency response of MICROPHONE.

4. MIC ON/OFF/MIC OVER SWITCH – To set MIC on and off, when switch at the MIC OVER position, the

mic1 and 2 on, the sound level for everything other than that from the MIC will decrease to around 20dB.

5. CUE PAN CONTROL – This function allows you to monitor the CUE level as well as the Program (main

output) level in your headphones. When you turn the CUE PAN to the full left position, you will only hear

the CH 1 signal you playing, on the contrary you will only hear the CH 2 signal you playing. If the CUE PAN

KNOB is set to the center position, you can cue both the channels signal you playing.

6. CUE LEVEL CONTROL – This rotary knob is used to adjust the headphone volume output level. Turn the

knob in a clockwise direction to increase the headphone volume.

7. HEADPHONES JACK – This jack is used to connect your headphones to the device allowing you to

monitor the cue channel. Always be sure the CUE LEVEL VOLUME is set to minimum before you put the

headphones on.

FRONT PANEL

1 2 3 4 5 6 7

Front pannel

Djinn Pro - Multimedia platform for mixing and playback

Page 7

1. USB 1 PORT – This is the USB port where you

insert your USB mass storage device for playing

MP3 files.

2. MASTER VOLUME CONTROL – This rotary knob

is used to control the master output level

(volume). To avoid distorted output try to main-

tain an average output signal level +4 dB. Be

sure this volume control is always set to zero

before turning the unit on.

3. BOOTH CONTROL – This rotary knob is used to

adjust the level of the BOOTH outputs.

4. RELAY BUTTON – This button is used to switch

the RELAY on and off. The left and right players

will automatically be in the single play mode when

the relay function is activated. On the contrary, the

left and right players will automatically be in the

continuous play mode.

5. MASTER METER BUTTON – This button is used

to choose between master level indicators and

channel level indicators.

6. CHANNEL FADER – These faders are used to control the output signal of any source assigned to its

particular channel. However, master volume is controlled by the MASTER VOLUME CONTROL.

7. FADER START SWITCH – This function works in conjunction with a compatible player. When used with a

compatible player, you can use the crossfader to start and stop a player with the mixer’s crossfader. The

ON/OFF switch activates the FADER START feature. If this function is activated, the FADER START

automatically returns the player to the preset cue point.

8. CROSSFADER – This fader is used to blend the output signals of channels 1 and 2 together. When the fader

is in the full left position (channel 1), the output signal of channel 1 will be controlled by the master volume

level. The same fundamentals will apply for channel 2. Sliding the fader from one position to another will

vary the output signals of channels 1 and 2 respectively. When the crossfader is set in the center position,

the output signals of both the channel 1 and channel 2 will be even.

9. XFADER CURVE SWITCH – Allows adjusting the “shape” of the crossfader response from a gentle curve for

smooth, long running fades, to the steep pitch required for top performance cut and scratch effects.

10. LEVEL METER – The dual LED’s indicators are used to detail either the master output level, a combination

of the master output level or the PGM monaural level.

11. CHANNEL EQ CONTROL – Both of the channels include a three-band signal EQ. These controls are used

to increase or decrease the HI’s, MID’s, LOW’s and frequency of the output signal.

HIGH frequency control

This knob is used to adjust the high levels of a channel allowing for a maximum high gain of 10dB or

maximum decrease of –35dB. Turning the knob in a counter- clockwise direction will decrease the

amount of high applied to a channel signal, turning the knob in a clockwise direction will increase the

amount of high applied to a channel signal.

MID frequency control

This knob is used to adjust the midrange levels of a ch annel allowing for a maximum midrange gain of

10dB or maximum decrease of –35dB. Turning the knob in a counter-clockwise direction will decrease the

amount of midrange applied to a channel signal, turning the knob in a clockwise direction will increase the

amount of midrange applied to a channel signal.

LOW frequency control

This knob is used to adjust the low levels of a channel allowing for a maximum bass gain of 10dB or

maximum decrease of -35dB. Turning the knob in a counter-clockwise direction will decrease the amount

of low applied to a channel signal, turning the knob in a clockwise direction will increase the amount of

low applied to a channel signal.

KILL EQ control

Press the EQ knob to activate the KILL function to the lowest level “-35dB”.

Mixer pannel

Djinn Pro - Multimedia platform for mixing and playback

Page 8

12. CHANNEL GAIN CONTROL – This adjustment is used to adjust an audio source signal input gain for a

channel. Never use the gain control to adjust output volume. Setting the gain level properly will ensure a

clean output signal. To properly set the gain level controls:

(1) Be sure the MASTER VOLUME CONTROL is set to minimum.

(2) Set the CHANNEL FADER to level 7.

(3) Begin play on an audio source connected to the channel you are adjusting.

13. SOURCE SELECTOR SWITCH – These switches are used to s elect the input source assigned to each

channel. Each channel may only be assigned one input source at a time.

CH1 selected to PC + CH2 selected to PC – the entire unite works as a MIDI controller.

CH1 selected to PC + CH2 selected to DECK B – the Deck A works as a MIDI controller, the mixer works

internally with Deck B.

CH1 selected to PC + CH2 selected to LN2/ PH2 – the Deck A works as a MIDI controller, the mixer works

internally with LN2/PH2 input.

Source Condition

CH1

CH2

DECK A

DECK B

DECK A

L2/P2

DECK A

L1/P1

DECK B

L1/P1

L2/P2

L1/P1

DECK B

L2/P2

DSP Input 1

DSP Input 2

—

L2/P2

—

USB Input 2

L1/P1

—

L1/P1

L2/P2

L1/P1

USB Input 2

USB Input 1

—

USB Input 1

L2/P2

USB Input 1

USB Input 2

DSP Output 1

DSP Output 2

USB Output 1

USB Output 2

REC

PHONES

REC

PHONES

REC

PHONES

L2/P2

REC

PHONES

REC

PHONES

REC

PHONES

L2/P2

REC

PHONES

L1/P1

REC

PHONES

L1/P1

REC

PHONES

L1/P1

L2/P2

Djinn Pro - Multimedia platform for mixing and playback

Page 9

1. POWER INLET (AC IN) – Use the accessory power cord to connect to an AC power outlet.

2. POWER SWITCH – Turn this unit power ON/OFF.

3. USB 2 PORT– This is the USB port where you insert your USB mass storage device for playing MP3 files.

5. BALANCED XLR MASTER OUTPUT JACKS – The Master Output includes a pair of XLR Balanced jacks.

The 3-pin XLR jacks send a high current balanced output signal. These jacks should be used when you will

be driving an amp or other audio equipment with a balanced input, or whenever you will be running a signal

line greater than 15 feet. Always, use these jacks whenever possible.

6. UNBALANCED MASTER OUTPUT – The RCA jacks send a low current unbalanced output signal. These

jacks should only be used for shorter cable runs to signal processors or looping to another mixer. For cable

runs greater than 15 feet use the XLR BALANCED JACKS.

7. BOOTH OUTPUT JACKS – Connect to inputs of your active monitors using cables with RCA connectors.

8. LINE/PHONO SELECTOR SWITCH – These switches are used to change the voltage line levels of there

respected LINE/PHONO RCA inputs jacks.

When connecting turntables with magnetic cartridges to these

jacks be sure the corresponding switch is in the PHONO” position, and when using line level input devices

be sure the switch is in the “LINE” position.

CAUTION: Always be sure main power is shut off before

change the position of the Line Level Selector Switch.

9. CHANNEL LINE/PHONO INPUT CONNECTORS – Turntables equipped with MM pickup cartridge (All DJ

turntable use MM pickup cartridges) may be connected to these jacks as long as the LINE/PHONE selector

switches is in the “PHONE” position. CD players, Tape Decks and other line level instruments may only be

connected to these jacks as long as the LINE/PHONE selector switches are in the “LINE” position. Input

volume will be controlled by the Channel gain control knob.

10. GND (GROUND TERMINAL) – Be sure to connect turntable ground leads to either or both of the two

available ground terminals. This will reduce the humming and popping noises associated with magnetic

phono cartridges.

11. MICROPHONE 2 JACK – This combo jack will accept a standard 1/4 plug or XLR 3-pin balanced male

plug. The volume output level for microphone will be controlled by its own respective VOLUME KNOB.

3 4 5 6 7 8 9 10 11

Djinn Pro - Multimedia platform for mixing and playback

Rear pannel

Page 10

4. USB MIDI PORT –

intended only for MIDI assignments. In the computer operation system this device will be automatically

recognized without any special drivers. Moreover, this device equipped with 2In/2Out sound card. The 2

stereo inputs are independent switchable for Line or Phono. It has especially been designed for DJs for an

easy set up of DVS and you can send the external line-in audio to computer via the USB MIDI port.

NOTE: USB cable no more than 3m long.

Connect the included USB cord to the USB MIDI port and to your computer. This port is

1. AUTO CUE – This will indicate if the Auto Cue is on or off. Press and hold the SGL/CTN button for 1

second to turn the Auto Cue function on and off.

2. RELOOP INDICATOR – Appears when LOOP is engaged or ready to be engaged.

3. SINGLE INDICATOR – This indicates that the player is in single play mode; the track will play once and

return to CUE mode. If the single indicator is not on, the unit is in continuous mode. In continuous mode the

device will play all the remaining tracks.

4. MP3 INDICATOR – Displays when a USB device has MP3 files on it.

5. TRACK DISPLAY- This indicator describes which track is currently cued or is playing.

6. REMAIN/ELAPSED INDICATOR- When REMAIN is indicated in the VFD Display the time meter will show

the current track's remaining time. When ELAPSED is indicated in the VFD Display the time meter will

show the current track's elapsed time.

7. TIME METER – The meter will detail either the elapse or remaining time of a track in Minutes, Seconds

and Frames. The display time will depend on the selected time mode. The selected time function will be

displayed beside the TIME METER as either Remaining track time or Elapsed track Time.

8. TIME BAR INDICATOR – This bar gives a visual approximation of a track's remaining time. This bar will

begin to flash when a track is ending. The flashing bar is great reminder that time is running out to get that

next track ready to go.

9. PITCH INDICATOR – This meter will indicate how much pitch is either being applied or will be applied.

10. KEY LOCK – This will indicate the KEY Lock function is active.

11. MEMORY BUCKET – This meter serves two functions.

(1) The bucket outline indicates your cue memory status. a full outline lets you know the cue memory is full.

(2) The five bars inside the bucket represent the digital buffer. Each bar represents 2 seconds.

12. BPM METER – This meter will display the BPM's of the current track.

13. AUTO BPM – This will indicate that the AUTO BPM counter is active.

14. ALPHANUMERIC DISPLAY – Indicates the current name of the track, of the folder. All kinds of other

interactive information are also shown.

15. FOLDER DISPLAY – This indicates which folder you are in.

16. TOUCH INDICATOR – This appears when anything touches the jog wheel.

17. CUE INDICATOR – This indicator will glow when the unit is in CUE mode.

18. PLAY/PAUSE INDICATOR – Indicates the player is in play mode (" "), or the player is in pause mode ("

").

13 11

765

VFD DISPLAY

Djinn Pro - Multimedia platform for mixing and playback

Page 11

Hold the FOLDER knob for 2 seconds to enter the internal menu, and turn FOLDER knob to search through

the different menu.

Turn the TRACK KNOB; or turn Jog Wheel to change the submenus.

Save and exit internal menu, turn the FOLDER knob to F. Exit & Save and press the TRACK knob, the display

indicates “Saving”.

NOTE: Anytime you can exit the internal menu just press the FOLDER knob. However, the modified setting

would not be saved.

1. Playlist – Normal / Title/ Artist / Album/ Genre

The DATABASE BUILDER can generate “Playlist” for USB device. You can adjust various criteria in order

to filter track in this setting.

You can turn the TRACK knob to select “Normal / Title/ Artist / Album/ Genre” and press the FOLDER knob

again to memorize your setting and exit the internal menu.

Normal: This is the default setting. The tracks are played corresponding to the established hierarchical

data structure.

Title: It is possible to continuously and alphabetically browse track database through the title structure.

Artist: It is possible to continuously and alphabetically browse track database through the Artist’s name

structure.

Album: It is possible to continuously and alphabetically browse track database through the Album structure.

Genre: It is possible to continuously and alphabetically browse track database through the Genre structure.

2. Repeat Mode – 3 different mode: Play All repeat/ Folder/Track

3. MIDI CH – Setup MIDI Channel from 1 to 16 (deck A – mixer – deck B).

4. MIDI Setup

TAP =HOLD/TOGGLE

I/O = Hide/ DIS. (hide/display MIDI I/O value)

4 - Internal menu

Djinn Pro - Multimedia platform for mixing and playback

Page 12

5. MIDI/Audio config

This menu allows you to select the operating mode of the Jinn:

- Mode 1: Djinn is completely MIDI compatible except cross fader and master button.

- Mode 2: Both player buttons are MIDI compatible. Center mixer is not MIDI compatible

(real mixer even in MIDI mode)

- Mode 3: DJinn is completely MIDI compatible but can only be used as a MIDI controller.

USB and Input are no longer available.

MIXER DECK 2DECK 1

MODE 1 and MODE 2

MIXER

SOFTWARE

INTERFACE

DECK 2DECK 1

MODE 3

MASTER

CUE

Page 13

Djinn Pro - Multimedia platform for mixing and playback

6. Cross Fader

Lock =To lock the crossfader in the middle of two channel.

Unlock=The crossfader is back to normal status.

7. Cross Fader Reverse

ON =Reverse the crossfader

OFF =Normal mode

8. Display Time – 0.5 ~ 12.0 sec. (line name start/stop time adjustment)

Scroll Speed – 50 ~ 2000 msec. (line name move time adjustment)

A. Sensitivity – Touch Wheel Sensitivity Adjustment (Adjustment range is -20~+20).

B. PITCH BEND – SPEED=1 ~ 50. The pitch bend parameter determines the impact of the jog wheel on the

pitch bend function. The player comes with the pitch bend parameter set to 25. You can adjust the parameter

between 01 (very little impact) to 50 (extreme impact) to adapt the pitch bend function perfectly to your

personal taste.

C. Intensity – VFD Brightness (Brightness range is 1~4)

D. A.Cue Level – Change the AUTO CUE level (Level range is -36~-78dB)

E. Bite Rate –Display ON/OFF.

F. Version – CXX (Control version) DSPXX (DSP version)

G. Load Defaults – Press track knob to enter load defaults.

H. Exit & Save – Exit & Save setting to next power on (Press the TRACK KNOB to exit & save in any operating

mode

Note:

Save: U1/U2, PITCH ON/OFF, PITCH RANGE, SGL/CTN, AUTO CUE, TIME MODE, HOLD, KEY LOCK,

EFFECTS ON/OFF, PLAYLIST, REPEAT MODE, MIDI CHANNEL, MIDI SETUP, CROSSFADER,

CROSSFADER REVERSE, DISPLAY TIME, SCROLL S PEED, SENITIVITY, INTENSITY, A.CUE LEVEL,

DISPLAY

Defaults: U1/U2(U1), PITCH (OFF), PITCH RANGE (10%), SGL/CTN(CTN), AUTO CUE(ON), TIME MODE

(REMAIN), HOLD(OFF), KEY LOCK(OFF), EFFECTS(OFF), PLAYLIST (NORMAL), REPEAT MODE(ALL),

MIDI CHANNEL(1-2-3), MIDI SETUP(TAP=HOLD, I/O=HIDE), CROSSFADER(UNLOCK), CROSSFADER

REVERSE(Off), DISPLAY TIME(3sec), SCROLL SPEED(400ms), SENITIVITY(0), INTENSITY(4), A.CUE

LEVEL(-48dB),Bit rate display(ON)

Page 14

Djinn Pro - Multimedia platform for mixing and playback

1. Before making or changing connections, switch off the power and disconnect the power cord from the AC outlet.

2. Quality cables make a big difference in fidelity and punch. Use high-quality, audio cables.

3. Do not use excessively long cables. Be sure plugs and jacks are securely fastened. Loose connections

cause hum, noise, or intermittence that could damage your speakers.

4. Connect the RCA pin cords to the inputs on your amplifier.

CAUTION : Be sure to use the supplied control cord. Using another type of cable may result in damage.

5. Connecting to a Computer– Support computer operating systems include Windows Vista, Window XP, and

MAC OS X or later.

5 - Connection

Microphone

Computer

USB Storage Device

CD/MP3 Player

Speaker

Turntable

Main unbalanced

power amplifier

Main balanced

power amplifier

Page 15

Djinn Pro - Multimedia platform for mixing and playback

FUNCTION Type

FUNCTION CODE

(DECK A)

CC/Note

SHIFT

(Hold TAP)

FUNCTION CODE

(DECK B)

CC/Note

SHIFT

(Hold TAP)

ACTION

SW/ENC 05/17 44/56 05/27 44/66

7FH : ON

00H : OFF

SW/ENC 01/16 40/55 01/26 40/65

7FH : ON

00H : OFF

SW/LED 02/02 D-1 41 02/02 D-1 41

7FH : ON

00H : OFF

SW/LED 03/03 D#-1 42 03/03 D#-1 42

7FH : ON

00H : OFF

SW/LED 04/04 E-1 43 04/04 E-1 43

7FH : ON

00H : OFF

SW/LED 06/06 F#-1 45 06/06 F#-1 45

7FH : ON

00H : OFF

SW/LED 07/07 G-1 46 07/07 G-1 46

7FH : ON

00H : OFF

SW/LED

(Rouge)

08/08 G#-1 47 08/08 G#-1 47

7FH : ON

00H : OFF

LED

(Vert)

30 C3 30 C3

7FH : ON

00H : OFF

SW/LED

(Rouge)

09/09 A-1 48 09/09 A-1 48

7FH : ON

00H : OFF

LED

(Vert)

31 C#3 31 C#3

7FH : ON

00H : OFF

SW/LED

(Rouge)

0A/0A A#-1 49 0A/0A A#-1 49

7FH : ON

00H : OFF

LED

(Vert)

32 D3 32 D3

7FH : ON

00H : OFF

SW/LED

(Rouge)

0B/0B B-1 4A 0B/0B B-1 4A

7FH : ON

00H : OFF

LED

(Vert)

33 D#3 33 D#3

7FH : ON

00H : OFF

SW/LED 0C/0C C0 4B 0C/0C C0 4B

7FH : ON

00H : OFF

DECK A and DECK B

6 - MIDI MAP

Page 16

Djinn Pro - Multimedia platform for mixing and playback

FUNCTION Type

FUNCTION CODE

(DECK A)

CC/Note

SHIFT

(Hold TAP)

FUNCTION CODE

(DECK B)

CC/Note

SHIFT

(Hold TAP)

ACTION

SW/LED 0D/0D C#0 4C 0D/0D C#0 4C

7FH : ON

00H : OFF

SW/LED 0E/0E D0 4D 0E/0E D0 4D

7FH : ON

00H : OFF

SW/LED 0F/0F D#0 4E 0F/0F D#0 4E

7FH : ON

00H : OFF

SW/LED 10/10 E0 4F 10/10 E0 4F

7FH : ON

00H : OFF

SW/LED 11/11 F0 50 11/11 F0 50

7FH : ON

00H : OFF

SW/LED 12/12 F#0 51 12/12 F#0 51

7FH : ON

00H : OFF

SW/LED 13/13 G0 52 13/13 G0 52

7FH : ON

00H : OFF

SW/LED 14/14 G#0 53 14/14 G#0 53

7FH : ON

00H : OFF

SW/LED 15/15 A0 54 15/15 A0 54

7FH : ON

00H : OFF

SW 16 55 16 55

7FH : ON

00H : OFF

SW 17 56 17 56

7FH : ON

00H : OFF

SW/LED 18/18 C1 57 18/18 C1 57

7FH : ON

00H : OFF

SW/LED 19/19 C#1 58 19/19 C#1 58

7FH : ON

00H : OFF

SW/LED 1A/1A D1 59 1A/1A D1 59

7FH : ON

00H : OFF

SW 1B 5A 1B 5A

7FH : ON

00H : OFF

SW 1C 5B 1C 5B

7FH : ON

00H : OFF

SW/LED 1D/1D F1 5C 1D/1D F1 5C

7FH : ON

00H : OFF

JOG SW/ENC 27/18 66/57 27/28 66/67

7FH : ON

00H : OFF

MIDI MAP

Page 17

Djinn Pro - Multimedia platform for mixing and playback

FUNCTION Type

FUNCTION CODE

(DECK A)

CC/Note

SHIFT

(Hold TAP)

FUNCTION CODE

(DECK B)

CC/Note

SHIFT

(Hold TAP)

ACTION

SW 1E 5D 1E 5D

7FH : ON

00H : OFF

SW/LED 1F/1F G1 5E 1F/1F G1 5E

7FH : ON

00H : OFF

SW/LED 20/20 G#1 5F 20/20 G#1 5F

7FH : ON

00H : OFF

SW/LED 21/21 A1 60 21/21 A1 60

7FH : ON

00H : OFF

SW 22 61 22 61

7FH : ON

00H : OFF

SW 23 62 23 62

7FH : ON

00H : OFF

Pitch Slider

CENTER

PITCH BEND / 28 67 PITCH BEND / 28 67

7FH : ON

00H : OFF

VR 11 50 21 60 VR : 00~7F

VR/SW

CENTER/LED

12/24/29/24 C2 51/63/68 22/24/29/24 C2 61/63/68 VR : 00~7F

VR/SW

CENTER/LED

13/25/2A/25 C#2 52/64/69 23/25/2A/25 C#2 62/64/69 VR : 00~7F

VR/SW

CENTER/LED

14/26/2B/26 D2 53/65/6A 24/26/2B/26 D2 63/65/6A VR : 00~7F

Channel

Fader

VR 10 4F 20 5F VR : 00~7F

LED 2C G#2 2C G#2

7FH : ON

00H : OFF

LED 2D A2 2D A2

7FH : ON

00H : OFF

LED 2E A#2 2E A#2

7FH : ON

00H : OFF

LEVEL

METER LED

LEVEL METER

LED

1 1

00H ~ 7FA

MIDI MAP

Page 18

Djinn Pro - Multimedia platform for mixing and playback

FONCTION Type

Code de la Fonction

(MIXAGE CENTRAL)

CC/Note

SHIFT

(Hold TAP)

ACTION

SW/LED 37/37 G3 76

7FH : ON

00H : OFF

SW/LED 38/38 G#3 77

7FH : ON

00H : OFF

VR 31 70 VR : 00~7F

VR 32 71 VR : 00~7F

Cross Fader VR/SW/SW/CENTER 30/08/09/0A 6F/47/48/49 VR : 00~7F

VR 35 74 VR : 00~7F

VR 36 75 VR : 00~7F

SLIDER

VR 34 73 VR : 00~7F

33 72 VR : 00~7F

(ON) L

1 40

7FH : ON

00H : OFF

(OFF) L

2 41

7FH : ON

00H : OFF

(ON) R

SW 3 42

7FH : ON

00H : OFF

(OFF) R

SW 4 43

7FH : ON

00H : OFF

(L)

SW 7 46

7FH : ON

00H : OFF

(C)

SW 6 45

7FH : ON

00H : OFF

(R)

SW 5 44

7FH : ON

00H : OFF

MIDI MAP

Page 19

Djinn Pro - Multimedia platform for mixing and playback

MIDI MAP

CC-ABSOLUTE (VR, LEVEL METER LED) TYPE

Control Change messages are sent with status 0xBn, where n is the channel, for the specified CC controller.

MIDI ID is indicated with the Thus the controller

channel along with the CC number. The value from 0x00 to 0x7F, directly related to the location of the controller.

LEVEL METER LEDS

00~0B => ALL LEDS OFF

0C~17=>LED(-30) ON

18~23=>LED(-30, -20) ON

24~2F=>LED(-30, -20, -10) ON

30~3B=>LED(-30, -20, -10, -7) ON

3C~47=>LED(-30, -20, -10, -7, -4) ON

48~53=>LED(-30, -20, -10, -7, -4, -2) ON

54~5F=>LED(-30, -20, -10, -7, -4, -2, 0) ON

60~6B=>LED(-30, -20, -10, -7, -4, -2, 0, +2) ON

6C~77=>LED(-30, -20, -10, -7, -4, -2, 0, +2, +4) ON

78~7F=> ALL LEDS ON (-30, -20, -10, -7, -4, -2, 0, +2, +4, +7)

CC-RELATIVE (ENC) TYPE

Control Change messages are status 0xBn, where n is the channel, for the specified CC controller.

The value from 0x40 to indicate the change in the controller.

A message with data 0x43 indicates a positive change of 3.

A messages with data 0x31 indicates a negative change of 15.

SWITCH ON/OFF (SW, CENTER TYPE)

These messages are used for switches.

Control Change messages are sent with status 0x9n, SWITCH On and Off value are 0x7F and 0x00,

LED ON/OFF (LED TYPE)

These messages are used for LED.

Control Change messages are sent with status 0x9n, LED On and Off value are 0x7F and 0x00,

where n is the channel.

This is an offset to 0x40 “one’s complement” notation.

Thus the controller MIDI ID is indicated with the channel along with the CC number.

Djinn Pro - Multimedia platform for mixing and playback

Page 20

• Before installing the ASIO driver, connect the Djinn Pro to your computer and let the device recognition

procedure scroll down. A message will indicate that the hardware is recognized and ready for use.

•The ASIO for Djinn Pro supplied with the Djinn Pro on the UTILITY DISK.

•There is two version of this driver, depending on your operating system :

- AUDIOPHONY_DJinn_WIN32_2.9.25.zip for 32-bit

- AUDIOPHONY_DJinn_X64_2.9.25.zip for 64-bit

•Unzip the archive on your system.

•Open the folder where the archive was unpacked and run «Setup.exe».

•Select the language of your choice.

•Click «Install Driver».

•The driver installation starts.

•Windows 7 UAC checks each installation process, so at regular intervals dialog boxes ask you toconfirm

the facilities of thevarious parts of the driver. Click «YES» every time.

•At the end of the installation, you must restart the computer for the changes to take effect.

7 - Specific ASIO Driver Installation (Windows ® only)

7.1 - Installing the Djinn Pro ASIO driver

Page is loading ...

audiophony DJ inn Pro Owner's manual

Brand: audiophony

Model: DJ inn Pro

Category: DJ controllers

Type: Owner's manual

This manual is also suitable for

DJinn PRO

Download PDF

report

in other languages

français: audiophony DJ inn Pro Le manuel du propriétaire

audiophony DJ inn Pro Owner's manual

This manual is also suitable for

audiophony DJ inn Pro Owner's manual

in other languages

Related papers

Other documents