vax.co.uk
U86-PMe Series
Performance Floor2Floor
Let’s get started
vax.co.uk
Do’s
Thank you for buying this Performance Floor2Floor.
Taking care of your carpets
The Performance Floor2Floor is designed to make vacuuming carpets regularly, as eective and
ecient as possible and this user guide will help you get the most out of your machine.
Maintaining your carpets will ensure they keep their appearance for longer. You’ve chosen carpets
for your home for a reason and Vax will help you take good care of them.
Taking care of your Performance Floor2Floor
Also inside this guide are instructions on maintaining your new machine, so that it’s always ready
when you are to tackle your carpets.
Basic safety precautions
3 Turn o all controls on the vacuum cleaner before
disconnecting or connecting the power cord.
3 Always keep the power cord away from the brushes
whilst using your vacuum cleaner. After use always
wrap the power cord around the cord clips provided.
3 Always make sure both the pre-motor/post motor
lters are in place before use.
3 Always switch o the vacuum cleaner before
disconnecting or connecting the hose and accessories.
3 Keep all openings clear and free from debris as this
may aect the airow/suction.
3 Always replace the fuse in the plug with a 13amp fuse.
Always protect the power cable from heated surfaces
and open ames.
3 Use only CE approved 13amp extension cords,
non-approved extension cords may overheat. Care
should be taken to arrange the extension cord as
it can be a trip hazard.
Don’ts
8 Don’t use this vacuum cleaner if it has been dropped,
damaged or left outdoors.
8 Don’t run over the power cord or use vacuum cleaner
if the power cord or plug is damaged. Please contact
our Customer Care Line on: 0844 4128 455
(Mon-Fri 8.30am to 6.30pm, Sat 9.00am to 5.00pm).
8 Don’t handle the plug or use the vacuum cleaner
with wet hands.
8 Don’t vacuum up any ammable or combustible
materials (lighter uid, petrol, kerosene etc.) or
use the vacuum cleaner in an area with explosive
vapours or liquid.
8 Don’t vacuum up hot coals, cigarette butts, matches or
smoking hot burning items or use in an area where
there may be harmful uids (chlorine, bleach, and
ammonia drain cleaner).
8 Don’t attempt to remove blockages with sharp objects
as this may cause damage to your vacuum cleaner.
8 Don’t vacuum up hard or sharp objects such as glass,
nails, screws or coins etc.
8 Don’t use the vacuum cleaner with incorrect voltage
as this may result in damage or injury to the user.
The correct voltage is listed on the ratings label.
Let’s talk safety
Taking care of you
We’re here if you need us. Instead of taking me back
to the shop, simply visit:
vax.co.uk/support or call:
(UK) 0844 412 8455 (ROI) 1-800 928 308
Monday-Friday 8.30am to 6.30pm, Saturday 9.00am to 5.00pm
Calls are charged at the UK local rate. Before you call we’ll need you to have the following
information to hand: your machine, your proof of purchase or warranty registration code.
Alternatively, you can write to us at:
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
Let us know what you think @VaxUK
This vacuum cleaner is intended for household use
only and NOT for commercial or industrial use.
• Only use the vacuum cleaner indoors on dry surfaces
and keep the area you’re cleaning well lit.
• Keep ngers, hair and loose clothing from moving parts
and openings whilst using the vacuum cleaner.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance. Cleaning and user
maintenance shall not be made by children
without supervision.
• Only Vax recommend tools should be used with this
vacuum cleaner.
Contents Getting to know your machine
Let’s talk safety
Getting to know your machine
Getting started
Using your machine
Taking care of your machine
Let’s talk technical
What to do if it goes wrong
Getting in touch
Notes
Performance Floor2Floor
Hose
Hose
Name Performance Floor2Floor
Voltage 220-240V~50Hz
Wattage 1600W
Cord length 8/10m
Weight 6.5kg
Technical Specication
Subject to technical change without notice.
Handle
3-in-1 tool
Extension tube
Dirt container release button
Power on / o button
Pre-motor lter
Separator
Dirt container
Post-motor lter
Carpet height
adjuster
Handle release button
Quick release
cord hook
Hose to
machine connector
Included with
your machine
Floor2Floor Pet
+
TurboTool
Tool Connector
Pre-motor lter
Post-motor lter
Floor2Floor Total Home
+
Flexi-crevice tool
Flat upholstery tool
TurboTool
Filter Kit (Type 98)*
1-1-134233-00
Belt Kit (Type 1)*
1-1-130669-01
Pro Cleaning Kit (Type 2)
1-1-133326-00
Turbo Tool (Type 6)
1-1-134419-00
Flat Upholstery Tool
1-1-131394-00
Flexi Crevice Tool (Type 2)
1-1-131393-00
3-in-1 Tool
1-1-129167-00
Accessories & Consumables
*To purchase consumables and accessories, please visit vax.co.uk
Initial Setup for normal operation
1. Use the base accessories.
– Shortest hose.
– Extension tube set to shortest practicable length.
2. Clean lters installed.
3. Dust receptacle empty.
4. All Bleeds must be closed.
5. Variable Power set to Maximum.
6. Floor heads/tools set to Carpet Mode for carpet cleaning.
7. Mechanical Agitation turned ON for carpet cleaning.
8. Floor heads/tools set to Hard Floor Mode for hard oor cleaning.
9. Mechanical Agitation turned OFF for hard oor cleaning.
Insert the back panel
into the oorhead.
Insert the lower
cord hook into the
hole at the bottom
of the back panel.
Now take the small
clip and push it down
between the end of
the cord hook and the
machine, to lock the
cord holder in place.
Place the dirt container onto the machine.
Ensure the dirt container tabs line up with
the holes in the post motor lter cover.
Assembling your upright
Ensure that the back
of the dirt container
connects to the inlet tube.
Place dirt container on
machine and click into
place at the back panel.
Insert the short end of the
hose into the tube at the
back of the machine and
turn to lock.
Push the hose end into the
hose to machine connector.
Before you begin cleaning
• Always switch o and unplug the vacuum cleaner before connecting or disconnecting the hose/attachments, or
removing and emptying the dirt container.
• The vacuum cleaner is equipped with a thermal cut-out. If for any reason the vacuum cleaner does overheat the
thermostat will automatically turn the vacuum cleaner o. If this happens, switch the vacuum cleaner o and
unplug from electrical socket. Remove and empty the dirt container also check the vacuum cleaner for blockages.
Allow the vacuum cleaner to cool for approximately 1 hour (if you have cleaned the lters please wait 24 hours
for the lters to fully dry before putting back into the vacuum machine).
• Filters require cleaning at least every 3 months.
• If the vacuum cleaner is blocked, switch o and unplug before removing the blockage.
Push the on/o switch to
turn machine on.
Place your foot gently on the oorhead and pull the
handle backwards to recline the machine.
Getting started Using your machine
PLEASE READ ‘LET’S TALK SAFETY’ AT THE BEGINNING BEFORE USE
Wrap the power cord around the quick release cord
hook at the top and the lower cord hook, continue
wrapping the power cord until it is secure.
Attach TurboTool clip
to the handle. Snap
TurboTool into position.*
Inset the handle into the
top of the back panel until
it clicks into place.
Remove hose end from
the oorhead.
If required use
tool connector.
Choose an accessory.*
Push the quick release
cord hook to one side to
release the power cord.
Turn the height adjuster
dial backwards for the
carpet setting.
Turn the height adjuster dial
forwards for the hard oor setting,
the oorhead will tilt forward.
*Not applicable for all models *Not applicable for all models
Using accessories
Attach accessory
to hose end.
Place ngers under the
catch of the bin to dirt
container lid and pull to
release it.
Press dirt container
release button to remove
the dirt container.
MAX
40˚C
T
A
P
24hr
24hr
MAX
40˚C
Cleaning the shroud
HEPA post-motor lter maintenance
Cleaning the pre motor lter
Taking care of your machine Taking care of your machine
Press dirt container
release button to remove
the dirt container.
Place ngers under the
catch of the dirt container
lid and pull to release it.
The lid will lift on a hinge
Remove the pre-motor
lter to allow access to
the shroud.
Remove the exhaust cover
by turning it counter clockwise
and lifting it o. To nd the
post-motor lter.
Use the tab on the lter to
pull the lter out of
it’s housing.
Tap the shroud over the
bin to release dirt.
Tap the lter over a bin
to release dirt.
Wash the shroud under
running water and leave
to dry. The shroud will need
to be placed back correctly.
Hold the dirt container over a
bin and unclip the lock on the
bottom of the dirt container,
allowing the dirt to fall out.
Close the base of the dirt
container and click the
dirt container back on
to the back panel.
Emptying and cleaning the dirt container
MAX
40˚C
T
A
P
24hr
MAX
40˚C
T
A
P
24hr
Wash the lter
under running water
(40 degree max).
Remove the lter.
Leave to fully dry for a least
24 hours before placing
back in the machine.
Check the post-motor lter
for discolouration.
Always switch o and uplug the
vacuum cleaner before carrying
out any maintenance.
WARNING
The exhaust lter is designed to oer long life with no maintenance. The lter should be checked periodically
and when heavily discoloured it should be replaced. Please do not wash, scrub or brush the lter as this will
damage the delicate lter media.
Removing blockages from the TurboTool*
Removing debris
from the brushbar
Vacuuming the stairs
Switch o your vacuum
cleaner at the main
socket. Using a pair of
scissors cut any hair or
debris free from around
the brushbar.
Ensure that the vacuum
is upright at the top or
bottom of the stairs
while vacuuming.
Do not lean on the machine
while using the hose.
Changing the belt
Switch o your
vacuum cleaner at
the main socket and
unplug. Remove the 4
screws on the bottom
of the oorhead.
Lift the brush from the
machine starting at the
side without the belt on.
Squeeze the sides of the
oor plate to release it.
Unhook the belt from the
motor spindle in the belt
compartment. (This may
be easier if you use a
screwdriver to do this).
Remove the oor plate.
Place the new belt
around the brush bar.
Remove the belt cover.
Let’s talk technical Let’s talk technical
Feed the other side into
the belt compartment.
Using a screwdriver,
hook the belt onto the
motor spindle.
Reinsert the brushbar. One end of the
brushbar has a square slot, and one
end has a circular slot, ensure that it is
put back into the correct position.
*Not applicable for all models
3
4
1
2
Tabs
3
4
1
2
Tabs
3
4
1 2
Tabs
3
4
1 2
Tabs
Remove the rubber ring. Detach lower housing
and remove blockages.
Using a pair of
scissors cut any hair
or debris free from
around the brushes.
Line up the tabs on front of
housing and push together
to re-t. Slide the rubber
ring into groove to secure.
SolutionProblem
Warning: To reduce the risk of personal injury, unplug the vacuum cleaner before performing
maintenance/troubleshooting checks.
What to do if it goes wrong Getting in touch
• The plug may not be fully pushed into the electrical socket.
• Check the fuse in the plug if this needs replacing, always replace with
a 13amp fuse.
• The motor thermostat may have tripped. If this has happened, unplug
the vacuum cleaner. Remove and empty the dirt container and check
the hose for blockages. Clean the lters and allow the vacuum cleaner
to cool for approximately 1 hour (if you have washed the lters you
will need to wait 24 hours for the lters to fully dry before putting
them back into the vacuum cleaner).
Why won’t the vacuum
cleaner turn on?
• The vacuum cleaner is making a whistling noise, please remove
the dirt container open the bottom and clean the seals. Replace the
dirt container and retry.
• If there is air sucking noise from the top of the dirt container, this
would indicate a blockage in the machine. Go to ‘Why won’t the
vacuum cleaner pick up above’.
What if my vacuum
cleaner is making an
excessive noise?
• The brushbar may be jammed. If this happens then the machine
needs to be switched o immediately to avoid damage. To remove
debris from brushbar refer to page.
• The belt might not turn if it is broken. To check the belt, go to the
‘Changing the belt’ page.
My brushbar
isn’t turning?
* Calls are charged at the UK local rate. Please make a note of the serial number and model number of the vacuum cleaner
before calling.
• There may be a blockage in the hose. Please remove the hose from
the vacuum cleaner, check and clear any blockages.
• Empty the dirt container and clean lters. Go to the ‘Taking care of
your machine’ page*.
• The brushbar may not be turning. Go to ‘My brushbar isn’t
turning?’ below.
• If the accessory/tool will not pick up, check and clear any blockages.
Why won’t the vacuum
cleaner pick up?
• Check the ‘This pack contains’ panel on the box to make
sure the part is included with your machine.
There is an accessory
missing?
Accessories
Don’t forget your accessories!
Order at: www.vax.co.uk/spares-and-solutions
Pro cleaning kit
1-1-133326-00
All our best tools all in one kit that makes cleaning
your home quicker, easier and with even better results.
We’ve taken care of cleaning all of the hard to reach
areas such as on top of cupboards and in between
blinds to the dust that collates behind and
within the radiator.
Notes
Flexi Crevice Tool
1-1-131393-00
A handy long, exible tool for getting far behind and
around furniture.
TurboTool (Type 6)
1-1-134419-00
Use the TurboTool for vacuuming your stairs,
upholstery and car interiors. It’s great for picking up
stubborn pet hair.
Flat Upholstery Tool
1-1-131394-00
Cleans large areas of upholstery like sofas and
curtains, quickly and eectively.
3-in-1 Tool
1-1-129167-00
3-in-1 dusting brush, upholstery tool and
crevice tool for cleaning awkward areas such
as furniture, skirting, blinds and stairs.
Vax Ltd., Kingswood Road, Hampton Lovett, Droitwich, Worcestershire, WR9 0QH, UK
email: inf[email protected] website: vax.co.uk
Version 2.0
EEC Statement of Compliance: Manufacturer/EEC importer: Vax Limited, hereby on our own responsibility,
declare that the U89-PMe Series is manufactured in compliance with the following Directives:
Safety: 2006/95/EC Low Voltage Directive. EMC: 2004/108/EC Electromagnetic Compatibility Directive
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice.
@VaxUK
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
