Kathrein UFS 923 Operating instructions

If you do not know the conﬁ guration of your satellite reception system, contact your

specialist dealer for ﬁ rst installation of the receiver.

Operating manual part 1 UFS 923

Connection and start-up English

Contents

Safety instructions – important notes ....................................................................................................... 2

Scope of supply ........................................................................................................................................... 5

Connection and start-up ............................................................................................................................. 6

Front/rear view of the receiver (front flap open) .......................................................................................... 6

Inserting batteries into the remote control ................................................................................................... 8

Connecting the unit ..................................................................................................................................... 9

TV connection ............................................................................................................................................. 9

Audio connection ....................................................................................................................................... 10

Digital .......................................................................................................................................................................... 10

Analogue ..................................................................................................................................................................... 10

Connecting up the Video/DVD recorder .................................................................................................... 10

Information about antenna connection and loop-through mode ................................................................ 11

First Installation ......................................................................................................................................... 12

Connection and Setup .............................................................................................................................. 18

DiSEqC™1.0 ............................................................................................................................................................... 18

DiSEqC™1.1 ............................................................................................................................................................... 20

Motorised Antenna (DiSEqC™1.2/ DiSEqC™1.3/USALS) ......................................................................................... 22

Motorised Antenna (DiSEqC™1.2) .............................................................................................................................. 23

Motorised Antenna (DiSEqC™1.3/USALS) ................................................................................................................. 27

Single LNB .................................................................................................................................................................. 30

Single-cable system .................................................................................................................................................... 32

Single-cable system - EXR .../EXU ... ......................................................................................................................... 33

Single-cable system - UAS 481 ................................................................................................................................... 35

Single-cable system - User Defined ............................................................................................................................ 37

Programme scan ......................................................................................................................................................... 40

Date and Time ............................................................................................................................................................. 42

Common Interface (CI) .............................................................................................................................. 44

Inserting the smart card and the CA module ............................................................................................................... 44

Troubleshooting ........................................................................................................................................ 45

Service ........................................................................................................................................................ 46

Technical Appendix ................................................................................................................................... 47

2

Power cable

Make sure that the mains cable

(power supply cable) is not damaged.

Units with a damaged mains cable

must be disconnected from the mains

(unplug it at the socket) and repaired

by an electrical specialist before

setup. Only use the power pack

supplied (if available).

Risk of death due to electric shock.

Danger!

Cleaning

Disconnect the mains plug before

cleaning the unit. Only use a dry cloth

for cleaning and only clean the outer

surface. Never open the casing of the

unit.

Touching the parts inside the unit

carries a risk of death due to electric

shock.

Playing children

Make sure that children do not push

any objects into the ventilation slots.

Risk of death due to electric shock.

Earthing

The antenna system must be earthed

as speciﬁ ed or equipotentially

bonded.

EN 60728/11 and any national

regulations must be complied with.

Risk of voltage surges due to lightning

strikes!

Mains voltage

Only operate the unit at the speciﬁ ed

mains voltage (indicated on the rear

of the unit or on the external power

pack). The unit may only be connect-

ed to the mains and turned on once

it has been connected to the antenna

and to the TV set or the cable network

and PC.

If the mains voltage is too high, there

is a risk of ﬁ re.

Damp, sunlight, heat, naked ﬂ ames

Protect the unit against moisture,

dripping and splashed water (do not

place any ﬁ lled objects such as vases

on top of the unit). Do not place the

unit close to a heater or expose it to

direct sunlight and do not operate it

in damp locations. Only use the unit

in a moderate climate, not in tropical

conditions! Place no naked ﬂ ames

such as candles on top of the unit!

There is a risk of ﬁ re!

Ventilation

The heat generated in this unit is

adequately dissipated. However,

the unit should never be installed

in a cupboard or on shelves with

inadequate ventilation. Never cover

the cooling slots on the unit (e.g.

with other equipment, magazines,

tablecloths, clothing or curtains).

Do not place any objects on top of

the unit. Unless stated to the contrary

in the "Connection and start-up" and

"Installation” sections in the manual

supplied, maintain a clearance of at

least 10 cm above the unit, 2 cm to

either side and 5 cm behind the unit,

to allow unobstructed dissipation of

the heat generated.

There is a risk of ﬁ re!

Batteries

If your unit was supplied with batteries

(e.g. for the remote control), take care

that the batteries are not exposed

to excessively high temperatures,

direct sunshine or ﬁ re. Exchange

the batteries only with types that are

identical or equivalent. Otherwise the

batteries or the remote control may be

damaged. Comply also with the safety

instructions stated on the batteries:

There is a risk of explosion!

Warning!

These two pages contain important information about operation, installation location and connection of the

unit. Read these instructions carefully before setting up the unit.

Do not

cover

Safety instructions – important notes

3

Periods of extended absence,

thunderstorms, mains socket

accessibility

In order to disconnect the unit from

the mains completely, the mains plug

must be unplugged from the wall

socket! Therefore install the unit close

to a mains socket and make sure that

socket is accessible at all times, so

that you can disconnect the unit from

the mains if necessary.

If you are away for an extended

period, and during thunderstorms,

always switch the unit off at the

mains and unplug it from the socket.

This also applies to the other

equipment connected to the unit.

Isolation from the cable network is

also recommended. Note any timer

programming (receiver) and turn the

unit on again promptly before the

recording time.

Installation location

All electronic equipment generates

heat. However, the heating of this

unit lies within the permissible range.

Sensitive furniture surfaces and

veneers may become discoloured by

the effects of constant heat over time.

The feet of the unit can also cause

colour changes to treated furniture

surfaces. If necessary, place the unit

on a suitable stable and ﬂ at base.

Repairs

Ensure that any repairs to your unit

are carried out by qualiﬁ ed personnel.

Opening the unit and attempting to

repair it yourself voids all warranty

claims.

Improper work on the unit may

jeopardize the electrical safety of the

unit.

The manufacturer accepts no liability

for accidents caused by the user

opening the unit.

Connections

Incorrect wiring of the connections

can lead to malfunctions or defects on

the unit.

Important

Electronic equipment must not be dis-

posed of in domestic waste. Accord-

ing to directive 2002/96/EC OF THE

EUROPEAN PARLIAMENT AND

COUNCIL of 27 January 2003 on

waste electrical and electronic equip-

ment, it must be disposed of profes-

sionally. At the end of its service life,

take this unit for disposal at a desig-

nated public collection point.

Spent batteries are special waste.

Do not throw spent batteries into your

domestic waste; take them to a collec-

tion point for used batteries.

Safety instructions – important notes

4

Product return/original packaging

Make sure that the fan at the rear of the unit and the ventilation slots on the unit are

not blocked or covered in any way. Otherwise the unit may overheat. Adjust the fan

speed to the temperature conditions in the receiver.

There is a risk of ﬁ re!

You must not disconnect the receiver from the mains while it is in operation!

This can lead to loss of data and corruption of the software.

Safety instructions – important notes

Please keep the original packaging in case you need to return the product at any time. The receivers are

fragile due to their construction and are only adequately protected by the original packaging. If the receiver

is not shipped correctly the guarantee/warranty on it will be voided.

Before you switch disconnect the receiver from the mains, you must switch it to the standby mode by press-

ing the stand-by button (on/off) on the remote control. In standby mode, any changed or new data that are

broadcast will be saved by the receiver. As soon as the receiver is in the standby mode, it can be discon-

nected from the mains at any time.

The information in this operating manual was correct at the time of going to press. We reserve the right

however to make changes at any time and without prior notice. If new software is released for your receiver,

and this affects the information in the operating manual (e.g. changes to the menus and/or functions), if we

believe it necessary we will make available a new operating manual for download under "www.kathrein.de".

Make a note of the receiver's basic settings (these are set during ﬁ rst installation), so you can restore them

if necessary!

Please remember your duty of care towards your fellow human beings! Keep the manual for any

questions that arise later, and if the building passes to another owner, pass it on to the new owner!

Instructions on how to set the fan can be found in the chapter "Main Menu", "Settings", "Basic Settings",

"Fan Settings".

Fan/ventilation slots on the unit

Switching the receiver off

Other matters:

Warning!

5

Scope of supply

■ UFS 923

■ Remote control RC 676 or 675

■ HDMI cable

■ Loop-through cable

■ Power cable

■ 2 batteries AAA 1.5 V

■ Operating manuals (part 1 and part 2)

■ Safety instructions (multi-lingual)

The included accessories may differ from the illustrations.

Loop-through cable

Power cable Remote control for

500 GB version.

HDMI cable

Remote control for

1000 GB version.

Batteries

6

Front/rear view of the receiver (front ﬂ ap open)

Connection and start-up

1 32 4 6 7 985

100V-240V~

50/60Hz

max. 55W

Elektroschock-Gefahr!

Nicht öffnen!

ON

OFF

VCR/AUX

TV

Video

Y

L

Pb

Pr

R

AUDIO

KOMPO-

NENTEN

DIGITAL

OUT

DiSEqC 1.2

LNB 2

LOOP OUT

LNB 1

LOOP OUT

LOOP

THROUGH

IF INPUT

950-2150MHz

14/18V max.400mA

22kHz

LNB2 IN LNB1 IN

Manifactured under license from

Dolby Laboratories. Dolby and the

double-D symbol are trademarks

of Dolby Laboratories.

10 11 12 13 14

15 16 17

18 19

20 21

22

24

23 25

7

Connection and start-up

*

)

CA modules and smart cards are not included with this product

**

)

The unit is not fully disconnected from the mains (see the sections "Safety Instructions - Important

Instructions" and "Periods of extended absence, thunderstorms, mains socket accessibility")

***

)

Accessories (optional) which can be purchased from your specialist dealer.

Rear view:

10. On/Off switch **

)

11. Mains power cable

12. Fan

13. Infra-red sensor connection ***

)

14. Network connection (Ethernet)

15. 2 x USB 2.0 ports (USB-A connectors)

16. HDMI connection

17. Scart socket for VCR/AUX connection

18. Scart socket for TV connection

19. Electrical data stream output (SPDIF/Sony

Philips Digital Interface Format) for Dolby

Digital AC 3 audio

20. Optical data stream output (SPDIF/Sony

Philips Digital Interface Format) for Dolby

Digital AC 3 audio

21. Audio outputs (L/R) - cinch sockets

22. Video output (composite colour)

23. 3 x cinch connections for component outputs

YUV labelled = Y/Pb/Pr

24. LNB 2-input (IN) and loop-through output

(LOOP OUT)

25. LNB 1-input (IN) and loop-through output

(LOOP OUT)

Front view (ﬂ ap open):

1. Common Interface for two (CI+) CA modules

for Pay-TV cards *

)

2. One button each for ejecting the respective

CA module

3. Record button

4. Stop button

5. USB 2.0 port

6. 16-character alphanumeric display

7. AUX button (Call up Kathrein-Portal

Mediacenter)

8. TV/R button

9. Multifunction control

HDMI = High-Deﬁ nition Multimedia Interface (digital interface for video and audio)

8

Connection and start-up

Remove the cover on the rear of the remote control. Insert the two batteries supplied into the remote control.

Ensure correct polarity of the batteries; the + and – markings as indicated inside the battery compartment.

Slide the cover back onto the housing until it locks in place.

Inserting batteries into the remote control

To open:

Press lightly here and pull off

backwards

9

If you do not know the conﬁ guration of your satellite reception system, contact your

specialist dealer.

Connect the Sat IF inputs on the receiver to the satellite reception system.

Use coaxial cable with an F standard connector (see illustration on right).

100V-240V~

50/60Hz

max. 55W

Elektroschock-Gefahr!

Nicht öffnen!

ON

OFF

VCR/AUX

TV

Video

Y

L

Pb

Pr

R

AUDIO

KOMPO-

NENTEN

DIGITAL

OUT

DiSEqC 1.2

LNB 2

LOOP OUT

LNB 1

LOOP OUT

LOOP

THROUGH

IF INPUT

950-2150MHz

14/18V max.400mA

22kHz

LNB2 IN LNB1 IN

Manifactured under license from

Dolby Laboratories. Dolby and the

double-D symbol are trademarks

of Dolby Laboratories.

HDMI

Scart

TV

Conventional DiSEqC™ system

Connect the satellite receiver (HDMI or alternatively TV Scart socket) and the TV set using a HDMI or Scart

cable (see connection example above).

Connecting the unit

TV connection

Connection and start-up

10

There are two ways you can access the digital audio.

HDMI

The stereo audio is transmitted to your TV set via the HDMI interface. If your TV set also supports Dolby

Digital, you can also receive the Dolby Digital audio via the HDMI interface (providing it is broadcast by the

channel provider). On this issue refer to the operating manual for your TV set.

SPDIF Dolby Digital output (electrical/visual)

The SPDIF outputs are intended for the connection of a Dolby Digital system (see "Advanced connection

example" in the technical appendix). Connect the SPDIF output (electrical or visual) and the Dolby Digital

system using an appropriate cable.

If you want to play the sound on your hi-ﬁ system, connect the audio cinch sockets to the input sockets on

the hi-ﬁ system, using an appropriate cable (see "Advanced connection example" in the technical appendix).

SPDIF = Sony Philips Digital Interface Format (digital output for Dolby Digital AC 3 audio)

Connect the satellite receiver (VCR/AUX Scart socket) to the video recorder/PVR using a Scart cable. To

play back a DVD, i.e. output the signal from the DVR through the receiver on the TV set, the TV set must

also be connected to the receiver with a Scart cable. This is required because the video signal from the VCR

scart socket on the receiver is not looped through/redirected to the receiver's HDMI output.

Audio connection

Digital

Analogue

If you are recording via an external video/DVD recorder, remember not to operate the receiver

during recording, otherwise all the on-screen displays will appear on your recording.

If the receiver is started as a result of a timer recording, you do not receive an image on your TV

set. You do not receive a TV image, i.e. the receiver is not started up, until you press the standby

button (on/off).

Connection and start-up

Connecting up the Video/DVD recorder

Tip!

11

If you wish to operate your UFS 923 on a single-cable system, please refer to the con-

nection example for single-cable systems (see "Technical Appendix", "Connection

examples")

This will only work when receiving one satellite, not in multifeed reception!

(Multifeed reception: simultaneous receipt of signals from more than one satellite)

To enable you to make use of all the reception and recording features of your Twin-DVR-HDTV Sat receiver,

such as

1. recording one program and at the same time viewing any other program or zapping through the channels,

and

2. recording two different programs at the same time,

the two tuner inputs of the satellite receiver must each be supplied with a dedicated satellite signal from the

antenna system/Sat outlet.

The receiver tuner inputs are factory preset on the installation menu to work with two separate Sat antenna

connections.

If you only have one antenna connection available, we recommend you interconnect the output of tuner 1

and the input of tuner 2 using the loop-through cable supplied (see page 5).

For this, in "First Installation" for tuner input 2 select

"Looped through" (see "First Installation" chapter).

Press the



button to access the "Tuner Con-

ﬁ guration" menu option, then select "Settings" and

"First Installation". Go through step-by-step until

you get to the tuner conﬁ guration.

You can make the settings here, though a restriction on this is that with tuner 2 you can only receive the

additional channels of the plane currently set by tuner 1 (e.g. Horizontal High). Therefore, only the channels

which can be selected are shown in the channel list.

Information about antenna connection and loop-through mode

Connection and start-up

12

Before you start to use the UFS 923, read the sections "Safety Instructions - Important

Instructions", "Important Information" and "Connection and start-up" through to the

item "First installation".

Do not connect the unit to the mains until all installation work has been properly carried out.

The guidance provided in the "First installation" section assumes that the receiver has been

properly connected as per the "Safety Instructions - Important Information" and "Connection and

start-up" sections through to the "First installation" section.

Buttons required for remote control during ﬁ rst installation:



...



Numerical input



(Green)

Call up the next step in

the ﬁ rst installation



(Red)

Go back one step in the

ﬁ rst installation



Conﬁ rming the changed values/

setting; sub-menu call-up



Selecting/changing individual

menu parameters, navigation



Abort input, go back

First switch your TV set on and select the AV-/HDMI input on it which you have used to connect the receiver

to your TV set. Switch on the receiver at the power switch on the rear of the unit. Undertake the ﬁ rst installa-

tion. If you have any questions or encounter problems, contact your specialist dealer.

The following on-screen display appears:

Always watch the bar at the bottom of the

on-screen display. Messages here provide

information on what to do next.

Use the



buttons to select the desired menu language for your UFS 923 and conﬁ rm your selection

using the



button. The selected language is indicated with a check. The following languages are avail-

able: German, English, French, Italian, Spanish, Czech, Dutch, Polish, Turkish and Russian.

First Installation

Connection and start-up

Tip!

13

For this, refer to the operat-

ing manual for your TV set and

take care to select only those

settings that your TV set can

process.

Press the



(green) button to move to the next menu.

The following on-screen display appears:

Use the



buttons here to select the basic set-

tings for the video and audio output of the receiver

to the TV set.

Video Output via

Select the connection on the receiver to which you have connected your television. Either

TV format

Here you can select the TV picture format. Either

- 4:3 or

- 16:9

Picture format

Here you can select the type of screen display,

depending on the setting of your TV aspect ratio:

- TV aspect ratio “4:3”: Pan & Scan or Letterbox

- TV aspect ratio “16:9”: Always 16:9 or Automatic

HDMI/YUV

SCART

or

HDMI/YUV format

Here you can select the picture resolution that will

be sent to the TV set. Either

- 1080p (resolution 1920 x 1080, full-screen images)

- 1080i (resolution 1920 x 1080, half-screen images)

- 720p (resolution 1280 x 720, full-screen images)

or

- 576p (resolution 720 x 576, full-screen images)

- Automatically

Force 576i (must be supported by the TV set

otherwise you will not see a TV picture)

You can only/only need to make this setting if you

have selected the setting "Automatic" for "HDMI/

YUV Resolution". If for a program that is trans-

mitted in the format 720 x 576 (standard TV),

Connection and start-up

14

the original format is to be transmitted to the TV

set, select the "On" setting. If the setting is "Off",

the program may be automatically scaled-up to

the HDTV format 720p by the receiver.

HDCP with free programs

Select here whether HDCP (digital copy

protection) is to be constantly set to “On” or is not

to be activated, “Off”. To view some programmes

it may be necessary for the setting to be

set to “On”.

TV control via HDMI (CEC)

If you select “Off“ on the TV it must be switched on

or off separately.

If you select “On“, the TV will automatically be

switched to “On“ when you start the receiver

(works only when the TV is in standby mode) to

ON.

When you turn the receiver into standby mode, the

TV will also be put into stand-by mode.

Automatic search and store or switching through

the receiver will only work if it is supported by the

TV set!

Display of 4:3 broadcasts

Here you can select the type of screen display

mode for 4:3 broadcasts on a 16:9 TV set. Either

- Normal (Pillar Box)

- Stretched (Full Screen) or

- Zoom in (Pan & Scan)

Audio format via HDMI

Here you can select the type of audio signal that

is transmitted by the HDMI interface. Select the

signal that your TV set can process:

- Decoded PCM or

- SPDIF format

Autom. Dolby Digital output

Here you can select whether the receiver should

automatically select the Dolby Digital soundtrack

(if this is transmitted).

TV Scart signal output

Select the type of video signal at the TV Scart

socket here. Select the signal that your TV set can

process.

- CVBS - Colour Video Baseband Signal or

- RGB - Red/Green/Blue signal or

- Y/C – S-Video signal (luminance/chrominance)

VCR Scart signal output

Select the type of video signal at the VCR Scart

socket here. Select the signal that your external

recorder can process.

- CVBS - Colour Video Baseband Signal or

- Y/C – S-Video signal (luminance/chrominance)

Autom. Dolby Digital output

Here you can select whether the receiver should

automatically output the Dolby Digital signal (if this

is transmitted).

Connection and start-up

15

Important instruction for picture

output using "YUV":

The "YUV" output can be used only if "RGB"

is not selected as the output signal for the

TV Scart socket!

In this case, select "Y/C" or "CVBS" as the

output signal for the TV Scart socket

You should perform the tuner conﬁ guration/make changes yourself only if you are

fully familiar with the particulars of your reception system.

The settings for the tuner con-

ﬁ guration should be made by

a specialist engineer for this

reception system.

Press the



(green) button to move to the next menu.

The following on-screen display appears:

If your receiver is connected as in the connection example (see illustration above), only one

change/selection is necessary in the rest of the ﬁ rst installation. If you are not familiar with the

details of your reception system, note the following:

In many cases the satellite reception system is a DiSEqC™ 1.0 system.

This type of system is preadjusted. Conﬁ rm the current on-screen displays using the



(green) button.

You then select, using the



buttons the required satellites in the satellite selection (in Germany

mostly ASTRA 19.2° East) and conﬁ rm the selection using the



button. Conﬁ rm the rest of the on-

screen displays during the ﬁ rst installation using the



(green) button. You cannot damage your recep-

tion system during this process! If you do not receive a TV picture at the end of the ﬁ rst installation,

contact your specialist dealer.

Connection and start-up

Tip!

16

You can set up the tuner conﬁ guration for the following types of reception systems:

- DiSEqC™1.0

- DiSEqC™1.1

- Motorised antenna (DiSEqC™1.2/DiSEqC™1.3)

- Simple LNB or

- One Cable

If your reception system is a single-cable system, continue from the item "Single-cable system" in

this chapter.

Before you start conﬁ guring the tuner, you must ﬁ rst perform both the "Tuner 2 type of connection" and "Sig-

nal conﬁ guration for Tuner 2” settings.

Tuner 2 type of connection

Select the type of connection for tuner 2 here. The currently selected setting is shown graphically in the con-

nection example at the top left of the screen. Either:

Separate:

The second tuner input of the receiver

(LNB2 IN) receives its own signal input

(i.e. there is a direct connection between

the antenna socket and tuner input 2). See

example illustration on the right.

Loop-through:

The second tuner input on the receiver

(LNB2 IN) receives the signal currently

looped through from the tuner 1 looped

through output. In this case, the second

tuner can receive only the channel level

currently being received by the ﬁ rst tuner.

See example illustration on the right.

See also "Information about antenna con-

nection and loop-through mode" earlier in

this chapter.

Connection and start-up

17

Signal conﬁ guration for tuner 2 (only for "Separate" connection mode)

Select the signal conﬁ guration for tuner 2 here. The currently selected setting is shown graphically in the

connection example at the top left of the screen. Either:

Same as tuner 1:

Both tuners are connected to the same sig-

nal source. See example illustration on the

right.

Different to tuner 1:

The two tuners are connected to different

signal sources (separate cables from the

LNB). See example illustration on the right.

The following conﬁ guration options are available for:

Tuner 2 type of connection "looped through":

All settings are performed at tuner 1. The second tuner is fed from the looped through output of the ﬁ rst tuner.

Tuner 2 type of connection "Separate" / Tuner 2 signal conﬁ guration "Same as tuner 1":

All settings are performed at tuner 1. The settings for the second tuner are automatically taken from the ﬁ rst

tuner.

Tuner 2 type of connection "Separate" / Tuner 2 signal conﬁ guration "Different from tuner 1":

All settings for both tuners must be performed separately.

Use the



buttons to set the parameters "Tuner 2 type of connection" and "Signal conﬁ guration for tuner

2" appropriate to the setting for your reception system.

Continue as described in the ﬁ rst installation for the type of reception you selected.

Connection and start-up

18

DiSEqC™1.0

Connection and Setup

The following display appears:

Tuner Conﬁ guration (Select Satellite) -

Tuner 1

Select the number of satellites that are

available in the signal on the Tuner 1 (max.

four).

Switch to the line “Satellite 1: .....“.

Press the



Button.

Press the



Green Button.

You receive the following message

(example):

Conﬁ guration Satellite 1

Accept the settings for the ﬁ rst satellite of

the tuner 1.

Satellite and Position:

Use the



Button to select the desired Satellite. Alternatively you can press the



Button to display

a list of all the satellites in the memory and then choose one.

LNB Type:

If your reception system does not have a Universal LNB, use the



Buttons to select the

LNB types that are used in your reception system. You can choose from the following LNB types:

19

Connection and Setup

- Universal

- Simple

- User deﬁ ned

If you are not using a Universal-LNB, Press the



Button. Now you can adjust the settings for your LNB

type (Simple or User deﬁ ned).

LNB Frequency (MHz):

Enter the LNB-frequencies (Low/High/Limit) with the numerical keys. Save the changed values using

the



Button.

DiSEqC™ Repeat

The setting for how often the DiSEqC™ command must be repeated depends on the conﬁ guration of

your reception system. Refer to the documentation for your reception system or seek assistance from a

specialist engineer.

- Off DiSEqC™ command is not repeated

- 1 DiSEqC™ command is repeated once

- 2 DiSEqC™ command is repeated twice

- 3 DiSEqC™ command is repeated three times

Test Transponder:

Select the “Test-Transponder” ﬁ eld. Here you can select a transponder for checking whether your

settings are correct using the signal strength bar and signal quality bar.

When you have completed all settings for this satellite, press the



Button.

If you have selected more than one satellite (max. four), the receiver will automatically skip to the settings

for the second satellite. Now do the settings for the second satellite, followed by the third and fourth

satellites as required, in the same way as described for the ﬁ rst satellite.

If you have completed the settings for tuner 1, Press the



Green Button.

When necessary, the receiver automatically jumps to the settings for the second tuner (This assumes that

you have chosen a “Separated“ Connection for the second tuner and the signal conﬁ guration for this tuner

will be “Different to tuner 1“). If this is the case, you can now perform the settings for the second tuner in the

same way as for the ﬁ rst tuner.

Once you have completed the settings for both tuners and the assigned satellites, the receiver will automa-

tically display the screen for the Programme scan. Continue the ﬁ rst installation with the “Programme scan”

section.

Please also refer to the enclo-

sed LNB documentation or con-

sult a system specialist.

Refer to the documentation of

your receiver system or consult

a specialist.

20

DiSEqC™1.1

Connection and Setup

The following on-screen display appears:

Select Satellites - Tuner 1

Here, you can select the available

satellites (max. 64).

Go to the next row.

Press the



Button.

The following on-screen display appears:

Press the



Green Button.

Satellite and Position:

Use the



Button to select the desired Satellite. Alternatively you can press the



Button to display

a list of all the satellites in the memory and then choose one.

LNB-Type:

If your reception system does not have a Universal LNB, use the



Button to select the

LNB types that are used in your reception system. You can choose from the following LNB types:

Page is loading ...

Kathrein UFS 923 Operating instructions

Kathrein UFS 923 Operating instructions

Related papers

Other documents