Samsung SCC-131A User manual

Part No.: AB68-00476A(01)

Printed in Korea

User Guide

SCC

-

130B/131B

SCC

-

130BP/131BP

SCC

-

100BP/101BP

E

F

G

ES

I

RU

J

1. Read all of these instructions.

2. Save these instruction for later use.

3. Unplug this appliance system from the wall outlet

before cleaning

Do not use liquid cleaners or aerosol cleaner.

Use a damp cloth for cleaning.

4. Do not use attachments not recommended by the

appliance manufacturer, as they may cause

hazards.

5. Do not use this appliance near water for example,

near a bathtub, washbowl, kitchen sink, laundry

tub, in a wet basement, or near a swimming pool,

etc.

6. Do not place this appliance on an unstable cart,

stand, or table.

The appliance may fall causing serious injury to a

child or adult, and serious damage to the

appliance.

Use only with a cart or stand recommended by

the manufacturer’s instructions, and use a

mounting kit approved by the manufacturer.

An appliance and cart combination should be

moved with care. Quick stops, excessive force,

and uneven surfaces may

cause the appliance and cart

combination to overturn.

iii

User Guide

E

The lightning flash, with an arrowhead

symbol, within an equilateral triangle, is

intended to alert the user to the presence of

uninsulated “dangerous voltage” within the

product’s enclosure, that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instruction in the

literature accompanying the appliance.

User Guide

ii

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

RISK OF ELECTRIC

SHOCK, DO NOT OPEN

CAUTION

WARNING : TO PREVENT FIRE OR SHOCK HAZARD, DO

NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

IMPORTANT SAFEGUARDS

13. Unplug this appliance from the wall outlet

and refer servicing to qualified service

personnel under the following conditions:

a. When the power cord or plug is damaged or frayed.

b. If liquid has been spilled into the appliance.

c. If the appliance does not operate normally by

following the operating instructions. Adjust only those

controls that are covered by the operating

instructions, as improper adjustment of other controls

may result in damage and will often require extensive

work by a qualified technician to restore the appliance

to normal operation.

d. If the appliance has been exposed to rain or water.

e. If the appliance has been dropped or the cabinet has

been damaged.

f. When the appliance exhibits a distinct change in

performance this indicates a need for service.

14. When replacement parts are required, be

sure the service technician has used

replacement parts specified by the

manufacturer that have the same

characteristics as the original part.

Unauthorized substitutions may result in fire,

electric shock, or other hazards.

15. Upon completion of any service or repairs to

the appliance, ask the service technician to

perform routine safety checks to determine

that the appliance is in safe operating

condition.

v

User Guide

E

7. Slots and openings in the cabinet on the back or

bottom are provided for ventilation, to insure

reliable operation of the appliance, and to protect

from overheating.

These openings should never be blocked by

placing the appliance on a bed, sofa, rug or other

similar surfaces. This appliance should never be

placed near or over a radiator or heat register.

This appliance should not be place in a built-in

installation such as a bookcase, unless proper

ventilation is provided.

8. This appliance should be operated only from the

type of power source indicated on the marking

label. If you are not sure of the type of power

supplied to your home, consult your dealer or

local power company.

9. Do not allow anything to rest on the power cord.

Do not locate this appliance where the cord will

be abused by people walking on it.

10. Do not overload wall outlets and extension cords,

as this can result in fire or electric shock.

11. Follow all warnings and instructions marked on

the appliance.

12. Do not attempt to service this appliance yourself,

as opening or removing covers may expose you

to dangerous voltage or other hazards. Refer all

servicing to qualified service personnel.

User Guide

iv

Contents

1. Introduction

........................................................

3

2. Features

..............................................................

4

3. Installation

..........................................................

5

Precautions in Installation and Use

....................

5

Connecting Auto Iris Lens Connector

.....................

6

Mounting Lens

.....................................................

7

Setting Lens Selection Switch

............................

8

Adjusting Back Focus

.........................................

9

Connecting Cable

................................................

11

4. Names and Functions of Parts

.......................

14

Names and Functions of Parts

...........................

14

Function Switches

................................................

16

5. Product Specification

.......................................

21

User Guide

2

1. Introduction

Adopting the latest Super -HAD CCD,these cameras

provide the best monitoring function when they are

connected to CCTV system.

❈ In the mechanical fluorescent light environment, if you

attach MANUAL IRIS and turn the ELC switch among

FUNCTION switches on, color may be rolled.

In this case, supply AC power before you turn L/L

switch among FUNCTION switches on.

(NTSC:60HZ , PAL:50HZ)

☞

COLOR ROLLING is the problem that color on the

monitor screen changes non-periodically.

This happens when White Balance is not fixed,

because a mechanical fluorescent light flickers

when it’s cycle is the same to the cycle of the power

frequency.

3

User Guide

E

3. Installation

Precautions in Installation and Use

 Do not attempt to disassemble the camera yourself.

 Be cautious in handling the camera. Avoid striking or

shaking the camera. Be cautious to avoid damage on

the camera caused by improper storage or operation.

 Do not expose this camera to rain or moisture. Do not

operate this camera on a wet place.

 Do not use strong or abrasive detergents when

cleaning the camera body.

Use a dry cloth to clean the camera.

 Keep the camera at a cool place away from the direct

sunlight. Leaving it under the direct sunlight may result

in the malfunction of the unit.

5

User Guide

E

2. Features

High Sensitivity

Adopting the 1/3" Super HAD CCD that has the latest built-

in microchip lens, the high sensitivity is realized.

Excellent Back Light Compensation

Even when an intense light source or sunlight is in the back

of your subject, a clear image will be provided due to the

ideal combination of the excellent performance of the high

light compression (KNEE Compensation) function and the

BLC (Back Light Compensation) function.

Digital Line-lock

The control and reliability have been enhanced due to the

Full Digital Line Lock, which allows users to adjust the Line

Sync Phase.

Resolution

High resolution is realized due to the Full Digital Image

Processing by the DSP for monitoring camera.

User Guide

4

7

User Guide

E

Mounting the Lens

Loosen a screw fixing the Flange Back Adjustment Ring by

turning it counterclockwise and turn the Adjustment Ring to

the "C" direction (counterclockwise) until it stops. Failure to

do so may result in a damage caused by the bump of the lens

against the image sensor part in the camera when mounting

the lens.

C Direction

Auto Iris Control Cable

Connecting Auto Iris Lens Connector

Prepare the following Auto Iris Lens Connector supplied

with the camera.

Connect the cable of the control cable, whose covering is

stripped, to the Auto Iris Lens Connector as shown below.

Pin Number DC Control Type Video Control Type

1 Damp(-) Power Source (+9V)

2 Damp(+) Not used

3 Drive(+) Video Signal

4 Drive(-) GND

User Guide

6

Rib

Pin1

Pin2

Pin3

Pin4

9

User Guide

E

Adjusting Back Focus

Although the Back Focus of the camera has been adjusted

in the factory before its shipment, the focus may not be

accurate for a certain type of the lens. In this case, follow

the procedures below to adjust the Back Focus. First,

following is how to adjust the Back Focus of the Fixed

Focus Lens.

 Lightly loosen the screw fixing the Back Focus

Adjustment Ring using a screwdriver.

 Image a vivid subject (with check patterns) at a distance

of more than 10m away and turn the Focus Ring to the

infinity () position.

 Adjust the Back Focus Adjustment Ring to obtain the

clearest image of the subject.

 Fasten the screw fixing the Back Focus Adjustment

Ring.

User Guide

8

Setting Lens Selection Switch

When lens mounting is completed, set the Lens selection

Switch on the side of the camera according to the mounted

lens type.

When the mounted lens is an Auto Iris Lens of the DC

control type, set the Lens Selection Switch to "DC".

When the mounted lens is an Auto Iris Lens of the Video

control type, set the Lens Selection Switch to "VIDEO".

11

User Guide

E

Connecting Cable

After mounting the lens and setting the Lens Selection

Switch, connect the prepared cable to each terminal of the

camera.

 First, connect one end of the BNC cable to the Video

Output Terminal (VIDEO OUT) of the camera.

 Then connect the other end of the BNC cable to the

Video Input Terminal of the monitor.

Video In Terminal on the rear of the monitor

BNC Cable

Video Out Terminal

(VIDEO OUT)

User Guide

10

The following describes how to adjust the Back Focus when

using a Zoom lens.

 Lightly loosen the screw fixing the Back Focus

Adjustment Ring using a screwdriver.

 Image a vivid subject (with check patterns) at a distance

of 3~5m away and adjust the zoom of the lens to TELE

as far as it goes. Then adjust the Focus Ring of the

lens to obtain the clearest image of the subject.

 Adjust the zoom of the lens to WIDE as far as it goes.

Then turn the Back Focus Ring of the camera to obtain

the clearest image of the subject.

 Repeat no.  &  2~3 times to exactly coincide the

zoom focus from TELE and with that from WIDE.

 Fasten the screw fixing the Back Focus Adjustment

Ring.

Note:

Turning the Back Focus Adjustment Ring to the "C" direction

beyond the adjustable range makes a sound at the limit.

13

User Guide

E

AC230V Power Input Camera

Connect the power input cord to the AC 230V power

source.

User Guide

12

 AC24V/DC12V Power Input Camera.

Connect 2 lines of the power adapter using a

Phillips screwdriver to the Power IN Terminal of the

camera as shown below.

 Without the distinction of the polarity, connect to

the AC 24V or AC 12V power source.

15

User Guide

E

 Auto Iris Lens Connector

Used for supplying power, which is required to control

the iris of the lens, as well as control signal, video

signal, or DC signal to the Auto Iris Control Lens.

 Auto Iris Lens Control Cable

Used for transmitting the control signals to the camera

to control the iris of the lens.

 Flange-Back Adjustment Ring

Used for adjusting the Back Focus.

 ALC Lens Selection Switch

Used when selecting the type of Auto Iris Lens to use.

DC : Select this switch to DC when Iris Lens requiring

DC control signal is mounted.

VIDEO : Select this switch to VIDEO when Auto Iris

Lens requiring VIDEO control signal is

mounted.

User Guide

14

4. Names and Functions of Parts

Names and Functions of Parts

• Side View

 Groove for Mount Adapter

Use this groove for fixing the mount adapter to be

connected to the bracket with screws to mount the

camera on the bracket.

 Auto Iris Lens (Option)

Lens to be mounted on the camera

Note

When the surface of the camera lens is contaminated,

wipe the surface gently with a tissue for lens or a cotton

cloth applied with ethanol.

# Auto lris Lens Connector

^ ALC Lens Selection

Switch

$ Auto Iris Lens Control

Cable

! Groove for Mount Adapter

@ Auto Iris Lens

%

Flange-Back

Adjustment Ring

 Power Connection Terminal

Terminal to be connected to the power (adapter) cable

Connect it to AC 24V or DC 12V.

 Power Indication LED

While the power is properly supplied to the camera, the

LED is turned on.

,  INC/DEC Switch

The LINELOCK mode is useful for controlling Vertical

Synchronous Phase.

17

User Guide

E

User Guide

16

AC24V/DC12V Power Input Camera

• Rear Panel

AC230V Power Input Camera

19

User Guide

E

3) SW3 (FL):

This is to prevent flicker on the screen when NTSC

system is used in 50HZ power supply region and PAL

system is used in 60HZ power supply region. That is to

prevent shaking on the screen resulted from the

discordance of the vertical sync frequency and the

flicker frequency of the illumination. While this switch is

ON, the electronic shutter is fixed to 1/100sec (NTSC)

or 1/120 sec (PAL).

4) SW4 (AWB ):

When setting up ON, the color of screen is adjusted

automatically in accordance with the change of lighting

color temperature by the change of outer environment.

(ATW) If the lighting condition is steady, OFF setting is

available. The camera memorizes the lighting color

temperature at the time when the switch setting is

changed from ON to OFF, and the camera color is

adjusted to the memorized color temperature. (AWC)

If the lighting color temperature is changed and you

want to make the camera be memorized/operated with

the changed color temperature, re-operate the switch

On/Off operation. However, be aware that an error may

occur under the following conditions.

First, a case that the subject is big, single color of the

high chroma, and in the center of the screen or a

case with almost no white color on the screen

Second, a case with a specific illumination such as a

natrium lamp

 To adjust the Vertical Sync Phase using the INC/DEC

switch in LL mode, the SW4 must be set to AWB “ON”.

 For DC 12V, the INT/LL mode is fixed to INT.

User Guide

18

 Function Switches

1) SW1 (LL):

When set to OFF, the camera operates in the Internal

Sync mode. When set to ON, it operates in the Power

Sync mode. If the camera is set to INT (Internal Sync)

when monitoring in the Auto Switching mode with more

than one camera connected to a sequential switcher, etc,

the jump of the screen will occur each time of screen

switching. To switch the screen gently without a jump, set

the camera to LL and adjust the Vertical Sync Phase using

the INC/DEC switch.

2) SW2 (ELC):

Use this switch with the Manual Iris Lens. While this

switch is ON, the speed of the electronic shutter varies

with the brightness of the subject from 1/60 to

1/120,000 sec for automatically controlling the

brightness of the screen. However, with the Auto Iris

Lens (DC or Video Control), be sure to switch OFF.

Color Rolling may occur in this mode.

In that case, input AC power source to the camera and

select SW1 “ON”.

(NTSC : 60HZ, PAL : 50HZ)

ON

1. L/L 2. ELC

3. FL 4. AWB

SW1 SW2 SW3 SW4

21

User Guide

E

5. Product Specifications

SCC-130B/131B

Item Contents

Product Type CCTV Camera

Broadcasting NTSC STANDARD SYSTEM

System

CCD 1/3” IT type S-HAD CCD

No. of Pixel 130B : 510(H) x 492(V)

131B : 768(H) x 494(V)

Scanning Type 525 Line, 2:1 Interlace

Frequency INTERNAL : 15,734 HZ(H)

59,94 HZ(V)

LINE LOCK :15,750 HZ(H)

60 HZ(V)

Sync Type INTERNAL

LINE LOCK

(When AC24V power source is used)

Resolution 130B : 330TV Lines

131B: 520TV Lines

S/N Ratio 50dB (AGC OFF)

Min. Object 130B : 0.15 Lux (F1.2)

Illumination 131B : 0.3 Lux (F1.2)

 DC Iris Level Control

When the ALC Lens Selection Switch is set to DC, adjust

this Iris Level Control using an adjustment rod such as a

screwdriver.

 Video Output Terminal

This is a terminal to be connected to the Input Terminal

of the monitor. Through this terminal, the video signals

are outputted.

User Guide

20

23

User Guide

E

SCC-100BP/101BP/130BP/131BP

Item Contents

Product Type CCTV Camera

Broadcasting PAL STANDARD SYSTEM

System

CCD 1/3” IT type S-HAD CCD

No. of Pixel 100BP/130BP : 500(H) x 582(V)

101BP/131BP : 752(H) x 582(V)

Scanning Type 625 Line, 2:1 Interlace

Frequency INTERNAL : 15,625 HZ(H)

50 HZ(V)

LINE LOCK :15,625 HZ(H)

50 HZ(V)

Sync Type INTERNAL

LINE LOCK

(When AC power source is used)

Resolution 100BP/130BP : 330TV Lines

131BP/101BP: 520TV Lines

S/N Ratio 50dB (AGC OFF)

Min. Object 100BP/130BP : 0.15 Lux (F1.2)

Illumination 131BP/101BP : 0.3 Lux (F1.2)

User Guide

22

ALC /ELC ALC

DC IRIS LENS

VIDEO LENS

ELC

Electronic SHUTTER IRIS function

1/60 to 1/120,000 sec

Color Temperature ATW/AWC Mode

BLC ON(Back Light Compensation)

AGC ON

Video Output COMPOSITE VIDEO OUT

1V p_p 75 /BNC

Power Source AC24V10%(60Hz0.3Hz)

DC12V -5% ~ +10%

Power Consumption About 3 Watts

Operating

-10~+50

Temperature

Operating

~90%

Humidity

Size 65(W) x 52(H) x 133(L)mm

(BNC included)

Weight 450g

User Guide

E

User Guide

24

ALC /ELC ALC

DC IRIS LENS

VIDEO LENS

ELC

Electronic SHUTTER IRIS function

1/60 to 1/120,000 sec

Color Temperature ATW/AWC Mode

BLC ON(Back Light Compensation)

AGC ON

Video Output COMPOSITE VIDEO OUT

1V p_p 75 /BNC

Power Source 100BP/101BP

AC220V~240V(50Hz0.3Hz)

130BP/131BP

AC24V10%(50Hz0.3Hz)

DC12V -5% ~ +10%

Power Consumption 100BP/101BP: About 4 Watts

130BP/131BP: About 3 Watts

Operating

-10~+50

Temperature

Operating

~90%

Humidity

Size 65(W) x 52(H) x 133(L)mm

(BNC included)

Weight 100BP/101BP : About 550g

130BP/131BP : About 450g

Page is loading ...

!

@

#

$

%

5

Super-HAD CCD

BLC

4

7

DC

Damp

(-)

(+9V)

Damp

(+)

Drive

(+)

Drive

(-)

GND

6

(Rib)

Pin1

Pin2

Pin3

Pin4

Page is loading ...

11

BNC

!

BNC

VIDEO OUT

@

BNC

VIDEO IN

BNC

VIDEO OUT

10

!

@

TELE

#

WIDE

$ @ #

TELE

WIDE

%

Page is loading ...

19

3) SW3 (FL):

NTSC 50Hz

PAL 60Hz

ON

NTSC

4) SW4 (AWB):

ON

(ATW)

ON/OFF

(AWC) AWB

18

%

Function

1) SW1 (LL):

OFF

ON

INT

INC/DEC

2) SW2 (ELC):

MANUAL

1/60 1/120,000

DC Video Control

OFF

AC

SW1 ON (NTSC:60Hz, PAL:50Hz)

ON

1. L/L 2. ELC

3. FL 4. AWB

SW1 SW2 SW3 SW4

Page is loading ...

23

SCC-100BP/101BP/130BP/131BP

CCTV

PAL

1/3 IT S-HAD CCD

100BP/130BP : 500(H) x 582(V)

101BP/131BP : 752(H) x 582(V)

625

: 15,625 HZ(H)

: 50 HZ(V)

(INTERNAL)

: 15,625 HZ(H)

: 50 HZ(V)

(

LINE LOCK

)

LINE LOCK

100BP/130BP : 330

131BP/101BP : 520

S/N

50dB

(

AGC OFF

)

100BP/130BP : 0.15 Lux (F1.2)

131BP/101BP : 0.3 Lux (F1.2)

22

ALC /ELC ALC

ELC

1/60(50)s~1/120Ks)

BLC

Back Light Compensation

AGC ON

1.0V p_p 75 /BNC

AC24V 0%(60Hz 0.3Hz)

DC12V -5%~ +10%

3 W

-10 ~+50

~90%

65(W) x 52(H) x 133(L)mm

450g

Page is loading ...

Samsung SCC-131A User manual

Samsung SCC-131A User manual

in other languages

Related papers

Other documents