Arcam AVR600 User manual

Category
AV receivers
Type
User manual

This manual is also suitable for

AVR600 / AV888
HANDBOOK AVR surround amplifier / AV processor
 






English
E-2
safety
guidelines
Important safety instructions
is product is designed and manufactured to meet
strict quality and safety standards. However, you should
be aware of the following installation and operation
precautions.
1. Take heed of warnings and instructions
You should read all the safety and operating instructions
before operating this equipment. Retain this handbook
for future reference and adhere to all warnings in the
handbook or on the equipment.
2. Water and moisture
e presence of electricity near water can be dangerous.
Do not use the equipment near water – for example next
to a bathtub, washbowl, kitchen sink, in a wet basement
or near a swimming pool, etc.
3. Object or liquid entry
Take care that objects do not fall and liquids are not
spilled into the enclosure through any openings. Liquid-
lled objects such as vases should not be placed on the
equipment.
4. Placing the equipment
Only use a rack or shelf that is stable and strong enough
to support the weight of this equipment.
5. Ventilation
Do not place the equipment on a bed, sofa, rug or
similar so surface, or in an enclosed bookcase or
cabinet, since ventilation may be impeded.
6. Heat
Locate the equipment away from naked ames or heat-
producing appliances such as radiators, stoves or other
appliances that produce heat.
7. Climate
e equipment has been designed for use in moderate
climates and in domestic situations. Unplug this
equipment during lightning storms to prevent possible
damage from a strike or mains surge.
8. Cleaning
Unplug the unit from the mains supply before cleaning.
e case should normally only require a wipe with a so,
lint-free cloth. Do not use chemical solvents for cleaning.
We do not advise the use of furniture cleaning sprays or
polishes as they can cause permanent white marks.
9. Power sources
Only connect the equipment to a power supply of
the type described in the operating instructions or as
marked on the equipment.
e primary method of isolating the equipment from
the mains supply is to remove the mains plug. e
equipment must be installed in a manner that makes
disconnection possible.
10. Power-cord protection
Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon
or against them. Pay particular attention to the point
where they exit from the equipment.
11. Power lines
Locate any outdoor antenna/aerial away from power
lines.
12. Speaker connections
Any speakers must be connected to the unit using class
II wire (i.e. no connection to Earth should be made).
Failure to observe this precaution may cause the unit to
become damaged.
13. Non-use periods
If the equipment is not being used for an extended
period, we recommend that you unplug the power cord
of the equipment from the outlet, to save power.
14. Abnormal smell
If an abnormal smell or smoke is detected from the
equipment, turn the power o immediately and unplug
the equipment from the wall outlet. Contact your dealer
and do not reconnect the equipment.
15. Servicing
You should not attempt to service the equipment.
Contact your dealer to arrange servicing.
16. Damage requiring service
e equipment should be serviced by qualied service
personnel when:
A. the power-supply cord or the plug has been
damaged, or
B. objects have fallen into, or liquid has spilled into the
equipment, or
C. the equipment has been exposed to rain, or
D. the equipment does not appear to operate normally
or exhibits a marked change in performance, or
E. the equipment has been dropped or the enclosure
damaged.
Safety compliance
is equipment has been designed to meet the IEC/EN
60065 international electrical safety standard.
is device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) is device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Class II product
is equipment is a Class II or double
insulated electrical appliance. It has been
designed in such a way that it does not
require a safety connection to electrical
earth (‘ground’ in the U.S.).
Many of these items are common sense precautions but, for your own safety and to ensure that you do not damage the unit, we recommend that you read them.






CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified
service personnel.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The lightning flash with an arrowhead symbol within an equilateral triangle, is intended to alert the user to the presence of
uninsulated ‘dangerous voltage’ within the products enclosure that may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the product.
CAUTION: In Canada and the USA, to prevent electric shock, match the wide blade of the plug to the wide slot in the socket
and insert the plug fully into the socket.
Français
F-1
consignes
de sécuri
Instructions de sécurité
importantes
Cet appareil a été conçu et fabriqué conformément aux
normes de qualité et de sécurité les plus strictes. Vous
devez cependant observer les précautions qui suivent
lors de son installation et de son utilisation.
1. Avertissements et consignes
Il est impératif de lire les consignes de sécurité et
d’utilisation avant de mettre cet appareil en marche.
Conservez ce manuel pour vous y référer par la suite et
respectez scrupuleusement les avertissements gurant
dans ce manuel ou sur lappareil lui-même.
2. Eau et humidité
L’installation d’un appareil électrique à proximité dune
source deau présente de sérieux risques. Il ne faut donc
pas installer lappareil près d’une baignoire, dun lavabo,
d’un évier, dans un sous-sol humide, près d’une piscine,
etc.
3. Chute dobjets ou inltration de liquides
Veillez à ne pas laisser tomber dobjets ni couler de
liquides à travers les ouvertures de lappareil et ne placez
pas sur l’appareil dobjet contenant du liquide, tel quun
vase par exemple.
4. Placement de léquipement
Utilisez uniquement une étagère assez stable et solide pour
supporter le poids de cet équipement.
5. Ventilation
Évitez de placer lappareil sur un lit, un canapé, un
tapis ou une surface similaire instable ou dans une
bibliothèque ou un meuble fermé. Ceci risquerait de
nuire à la ventilation du système.
6. Exposition à la chaleur
Ne placez pas l’appareil à proximité dune amme nue
ou de tout dispositif produisant de la chaleur : radiateur,
poêle ou autre.
7. Conditions climatiques
Lappareil est conçu pour fonctionner dans des climats
modérés. Déconnectez cet équipement pendant un
orage pour éviter tous dommages possibles dun impacte
de la foudre ou de surtension.
8. Nettoyage
Mettez l’appareil hors-tension avant de le nettoyer.
Pour lentretien du boîtier, utilisez uniquement un
chion doux, humide et non pelucheux. N’utilisez pas
de solvant chimique.
Lemploi daérosols ou de produits de nettoyage pour
meubles est déconseillé, car le passage dun chion
humide risquerait de laisser des traces blanches et
indélébiles.
9. Alimentation secteur
Branchez l’appareil uniquement sur une alimentation
secteur du type mentionné dans le manuel dutilisation
ou indiqué sur l’appareil lui-même.
Le principal moyen d’isoler lappareil du secteur est
d’utiliser l’interrupteur situé à larrière de lappareil.
Cet appareil doit être installé de façon à pouvoir être
débranché si nécessaire.
10. Protection des câbles d’alimentation secteur
Veillez à ce que les câbles dalimentation ne se trouvent
pas dans un lieu de passage ou bloqués par dautres
objets. Cette règle sapplique plus particulièrement aux
prises et câbles dalimentation et à leurs points de sortie
de l’appareil.
11. Câbles haute tension
Évitez de monter l’antenne extérieure de lappareil à
proximité de câbles haute tension.
12. Branchement des haut-parleurs
Tous les haut-parleurs doivent être connectés à
l’AVR600 avec du câble de classe II (aucune mise à la
terre nécessaire). Le non-respect de cette précaution est
susceptible d’endommager lappareil.
13. Périodes de non-utilisation
Si lappareil possède une fonction de mise en veille, un
courant faible continuera de circuler lorsqu’il sera réglé
sur ce mode. Débrancher le cordon secteur de la prise
murale si lappareil doit rester inutilisé pendant une
période prolongée.
14. Odeur suspecte
Arrêtez et débranchez immédiatement lappareil en cas
d’émission de fumée ou dodeur anormale. Contactez
immédiatement votre revendeur.
15. Service
N’essayez jamais deectuer dautres opérations que celles
mentionnées dans ce manuel. Toute autre intervention
doit être eectuée par un personnel qualié.
16. Entretien par des techniciens qualiés
Lappareil doit être entretenu par du personnel qualié
lorsque :
A. la prise ou le câble dalimentation a été endommagé,
B. des objets sont tombés ou du liquide a coulé dans
l’appareil,
C. l’appareil a été exposé à la pluie,
D. lappareil présente des dysfonctionnements,
E. l’appareil est tombé ou le boîtier a été endommagé.
Respect des consignes de
sécurité
Cet appareil a été conçu pour répondre à la norme
internationale de sécurité électrique EN60065.
Cet appareil est conforme à la Section 15 des règles
de la FCC. Son fonctionnement est soumis aux deux
conditions suivantes :
(1) ce produit ne risque pas de causer d’interférences
nuisibles et (2) ce produit doit accepter toutes les
interférences reçues, y compris celles qui risquent
d’entraîner un fonctionnement indésirable.
Class II produit
Ce produit est un appareil électrique à
isolation double (appareil de classe II).
Il a été conçu pour ne pas nécessiter de
connexion de sécuri à la terre (ou à la
masse).
Bon nombre des consignes ci-dessous sont de simples précautions de bon sens. Nous vous recommandons toutefois de les lire pour votre propre sécurité et pour celle de l’appareil.






ATTENTION : afin de réduire les risques de choc électrique, nouvrez pas le boîtier de l’appareil. Les pièces internes ne sont pas réparables
par l’utilisateur. Pour tout problème matériel, contactez des techniciens qualifiés.
ATTENTION : afin de réduire les risques de choc électrique et d’incendie, veillez à ne pas exposer cet appareil à la pluie ou à
l’humidité.
Le triangle dans lequel figure le symbole d’un éclair alerte l’utilisateur de la présence, dans le boîtier de lappareil, d’une tension
dangereuse, non isolée et suffisamment importante pour représenter un risque de choc électrique.
Le triangle dans lequel figure un point d’exclamation alerte l’utilisateur de la présence d’instructions de fonctionnement et de
maintenance (réparation) importantes dans la documentation accompagnant le produit.
ATTENTION : au Canada et aux États-Unis, afin de prévenir tout choc électrique, aligner la plus grosse broche de la prise à la fente la plus
large de la fiche et insérez entièrement la prise dans la fiche.
F2
F-2
E-3
English
welcome
ank you and congratulations for purchasing your Arcam FMJ AVR600 surround amplier or
AV888 AV processor.
Arcam has been producing specialist audio products of remarkable quality for over three
decades and the new FMJ products are the latest in a long line of award winning Hi-Fi. e
design of the FMJ range draws upon all of Arcams experience as one of the UKs most respected
audio companies, to produce Arcams best performing range of products yet – designed and built
to give you years of watching and listening enjoyment.
is handbook is intended to give you a detailed guide to using the AVR600 surround amplier
and the closely related AV888 AV processor. It starts by giving advice on installation, moves
on to describe how to use the product and nishes with additional information on the more
advanced features. Use the contents list shown on this page to guide you to the section of
interest.
We hope that your FMJ product will give you years of trouble-free operation. In the unlikely
event of any fault, or if you simply require further information about Arcam products, our
network of dealers will be happy to help you. Further information can also be found on the
Arcam website at www.arcam.co.uk.
e FMJ development team
Contents
safety guidelines .......................................E-2
welcome ......................................................E-3
before you begin… ..................................E-4
rear panel connectors ..............................E-7
audio/video connections ........................E-8
Connection guide ................................................ E-12
radio connectors .................................... E-14
other connectors .................................... E-16
speakers ................................................... E-18
operation ................................................. E-20
front panel operation ............................ E-22
remote control ........................................ E-23
essential setup ........................................ E-32
auto speaker setup ................................ E-33
setup menus ........................................... E-34
decoding modes .................................... E-40
Dolby volume ........................................................ E-42
tuner operation ...................................... E-44
network/usb operation ........................ E-46
external amplifiers ................................. E-47
multi-room set up .................................. E-48
Multi-room connection guide ........................ E-49
customising the CR102 ......................... E-50
Command summary ........................................... E-53
Device codes .......................................................... E-53
trouble shooting ..................................... E-54
specifications .......................................... E-56
product guarantee ................................ E-57
device code tables .....................................58
Professional Installation?
It may be that the unit has been installed and set up as part of your Hi-Fi installation by a qualied Arcam dealer.
In this case, you may wish to skip the sections of this handbook dealing with installation and setting up, and
move directly to the sections dealing with using the unit. Use the Contents list to guide you to these sections.
DIY setup?
e AVR600 and AV888 are powerful and sophisticated items of AV equipment. If you are setting a unit up
yourself, it is recommended that you read this handbook thoroughly before beginning. For instance, correct
speaker conguration and placement is a key to getting the most out of your FMJ product and making sure that
all the elements of your system work in harmony.
E-4
e AVR600 surround amplier and AV888 AV
processor are both designed to produce a level of
performance that will truly bring music and movies
to life.
e AVR600 is a high-quality and high-performance
home-cinema processor and amplier built to Arcams
quality design and manufacturing standards. e closely
related AV888 is a home-cinema processor which
provides multichannel input to an external amplier
(such as Arcams P777). ey both combine digital
processing with high-performance audio and video
components to form the locus of an unrivalled home-
entertainment centre.
e AVR600 allows switching and control of eight
analogue and seven digital sources in addition to
internal AM, FM and DAB radio or a SiriusConnect™
Home Tuner input – as well as networked and USB
audio sources – making it an ideal hub for both home-
cinema and two-channel stereo systems.
Since many of these source components are also capable
of generating video signals, both the AVR600 receiver
and the AV888 processor units include broadcast-
quality switching for HDMI, Composite, S-Video, RGB
and Component video signals. ere are audio and
video outputs for PVR and VCR recording, as well as
two digital outputs for digital recording of digitised
audio sources. DVD-Audio and SACD can be connected
via the multichannel input. Control of the AVR600 or
the AV888 is either by front panel control buttons, IR
remote control or RS232 port.
e CR102 remote control supplied with either unit
is an eight-device ‘universal’ learning remote control
which is simple to use, and once set up is able to control
a complete system. It can be programmed using its vast
internal code library to control CD and DVD players,
PVRs, TVs and other devices.
e installation of the AVR600 or AV888 in a listening
room is an important process which requires care at
every stage. For this reason, the installation information
is very comprehensive and should be followed carefully
to achieve an unrivalled level of performance.
before you
begin

 





E-5
English
Placing the unit
< Place the unit on a level, rm surface, avoiding
direct sunlight and sources of heat or damp.
< Do not place the unit on top of a power amplier or
other source of heat.
< Do not place the unit in an enclosed space such as
a bookcase or closed cabinet unless there is good
provision for ventilation. e unit will run warm
during normal operation.
< Do not place any other component or item on top of
the amplier as this may obstruct airow around the
heat-sink, causing the amplier to run hot. (e unit
placed on top of the amplier would become hot,
too.)
< Make sure the remote-control receiver on the front
panel display is unobstructed, otherwise this will
impair the use of the remote-control. If line-of-sight
is impractical, a remote-control repeater can be used
with the rear panel connector (see page 17).
< Do not place your record deck on top of this
unit. Record decks are very sensitive to the noise
generated by mains power supplies which will be
heard as a background ‘hum’ if the record deck is too
close.
Power
e amplier is supplied with a moulded mains plug
already tted to the lead. Check that the plug supplied
ts your supply – should you require a new mains lead,
please contact your Arcam dealer.
If your mains supply voltage or mains plug is dierent,
please contact your Arcam dealer immediately.
e amplier can be switched for operation between
195–265V (switch position 230V) and 85–132V (switch
position 115V).
NOTE
Ensure that the unit is switched o and the power
lead removed before changing the position of the
voltage range switch.
Push the IEC plug end of the power cable into the
socket on the back of the amplier, making sure that it
is pushed in rmly. Plug the other end of the cable into
your mains socket and, if necessary, switch the socket
on.
e amplier can be turned on using the POWER switch
on the front panel. While switched on, the front panel
LED will glow green.
Standby power
e unit can be switched into standby mode using
the
2
button on the CR102 remote control. While in
standby mode the front panel LED will glow red and
power consumption is around 3 watts.
While in Standby mode, it may be possible to hear a
slight residual hum coming from the mains transformer
inside the amplier. is is perfectly normal. However,
if the unit is to be le unused for an extended period,
we recommend that you disconnect it from the mains
supply to save power.
Interconnect cables
We recommend the use of high-quality screened cables
that are designed for the particular application. Other
cables will have dierent impedance characteristics
that will degrade the performance of your system (for
example, do not use cabling intended for video use to
carry audio signals). All cables should be kept as short
as is practically possible.
It is good practice when connecting your equipment to
make sure that the mains power-supply cabling is kept
as far away as possible from your audio cables. Failure to
do so may result in unwanted noise in the audio signals.
For information on speaker cabling, please refer to the
‘Speakers’ section, beginning on page 18.
Radio interference
e AVR600 and AV888 are audio devices containing
microprocessors and other digital electronics. ey have
been designed to very high standards of electromagnetic
compatibility.
is is a Class A product. In a domestic environment
this product may cause radio interference, in which case
the user may be required to take adequate measures.
If the unit causes interference to radio or television
reception (which can be determined by switching the
unit o and on), the following measures should be
taken:
< Re-orient the receiving antenna or route the antenna
cable of the aected receiver as far as possible from
the unit and its cabling.
< Relocate the receiver with respect to the unit.
< Connect the aected device and the unit to dierent
mains outlets.
If the problem persists, please contact your Arcam
dealer.
E-6
Dolby Volume
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Dolby True HD, Digital, Digital Plus,
PL IIx
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic, and the
double-D symbol are trademarks of Dolby
Laboratories.
DTS-HD Master Audio
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,212,872; 7,333,929;
7,392,195; 7,272,567 & other U.S. and worldwide
patents issued & pending. DTS is a registered
trademark and the DTS logos, Symbol, DTS-HD
and DTS-HD Master Audio are trademarks of
DTS, Inc. © 1996-2008 DTS, Inc. All Rights
Reserved.
DTS-HD High Resolution Audio
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,212,872; 7,333,929 &
other U.S. and worldwide patents issued &
pending. DTS is a registered trademark and the
DTS logos, Symbol, DTS-HD, DTS-HD High
Resolution Audio and DTS-HD High Res Audio
are trademarks of DTS, Inc. © 1996-2008 DTS,
Inc. All Rights Reserved.
DTS Digital Surround
ES|Neo:6|96/24
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,226,616; 6,487,535; 7,003,467; 7,212,872 &
other U.S. and worldwide patents issued &
pending. DTS, DTS Digital Surround, ES, and
Neo:6 are registered trademarks and the DTS
logos, Symbol and DTS 96/24 are trademarks
of DTS, Inc. © 1996-2008 DTS, Inc. All Rights
Reserved.
AAC/AAC Plus
aacPlus is a trademark of Coding Technologies.
See www.codingtechnologies.com for more
information.
FLAC
FLAC Decoder Copyright © 2000, 2001, 2002,
2003, 2004, 2005, 2006, 2007, 2008 Josh Coalson
Redistribution and use in source and binary
forms, with or without modification, are
permitted provided that the following conditions
are met:
- Redistributions of source code must retain the
above copyright notice, this list of conditions
and the following disclaimer.
- Redistributions in binary form must
reproduce the above copyright notice, this list of
conditions and the following disclaimer in the
documentation and/or other materials provided
with the distribution.
- Neither the name of the Xiph.org Foundation
nor the names of its contributors may be used
to endorse or promote products derived from
this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY
THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Ogg/Vorbis
Ogg/Vorbis Decoder Copyright © 2002,
Xiph.org Foundation
Redistribution and use in source and binary
forms, with or without modification, are
permitted provided that the following conditions
are met:
- Redistributions of source code must retain the
above copyright notice, this list of conditions
and the following disclaimer.
- Redistributions in binary form must
reproduce the above copyright notice, this list of
conditions and the following disclaimer in the
documentation and/or other materials provided
with the distribution.
- Neither the name of the Xiph.org Foundation
nor the names of its contributors may be used
to endorse or promote products derived from
this software without specific prior written
permission.
THIS SOFTWARE IS PROVIDED BY
THE COPYRIGHT HOLDERS AND
CONTRIBUTORS “AS IS” AND ANY EXPRESS
OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE
ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS
BE LIABLE FOR ANY DIRECT, INDIRECT,
INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF
SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER
IN CONTRACT, STRICT LIABILITY, OR
TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT
OF THE USE OF THIS SOFTWARE, EVEN IF
ADVISED OF THE POSSIBILITY OF SUCH
DAMAGE.
Trademark acknowledgements
Arcam is a registered trademark of A & R Cambridge Ltd.
WMA &
Microsoft
DRM10
This product is protected by certain intellectual
property rights of Microsoft Corporation. Use
or distribution of such technology outside of
this product is prohibited without a license from
Microsoft or an authorized Microsoft subsidiary
Content providers are using the digital rights
management technology for Windows Media
contained in this device (“WM-DRM”) to
protect the integrity of their content (“Secure
Content”) so that their intellectual property,
including copyright, in such content is not
misappropriated. This device uses WM-DRM
software to play Secure Content (“WM-DRM
Software”). If the security of the WM-DRM
Software in this device has been compromised,
owners of Secure Content (“Secure Content
Owners”) may request that Microsoft revoke
the WM-DRM Softwares right to acquire
new licenses to copy, display and/or play
Secure Content. Revocation does not alter the
WM-DRM Softwares ability to play unprotected
content. A list of revoked WM-DRM Software
is sent to your device whenever you download a
license for Secure Content from the Internet or
from a PC. Microsoft may, in conjunction with
such license, also download revocation lists onto
your device on behalf of Secure Content Owners.
vTuner
This product is protected by certain intellectual
property rights of NEMS and BridgeCo. Use
or distribution of such technology outside of
this product is prohibited without a license
from NEMS and BridgeCo or an authorized
subsidiary.
MP3
MPEG Layer-3 audio decoding technology
licensed from Fraunhofer IIS and Thomson
multimedia
iPod
iPod is a trademark of Apple Inc., registered in
the US and other countries.
Sirius
SIRIUS, XM and all related marks and logos
are trademarks of Sirius XM Radio Inc. and its
subsidiaries. All rights reserved. Service not
available in Alaska and Hawaii.
E-7
English
NOTE
Please read the ‘Placing the unit, ‘Power’ and
‘Interconnect cables’ sections on page 5 before
connecting up your AVR600 or AV888!
Voltage select
Ensure the voltage selected
matches your local power supply
rear panel
connectors
























































     



 


















 






















HDMI
For information, see page 8.
Speaker connectors
For information, see page 18.
Power inlet
Connect the correct mains
cable here
Video connectors
Component, S-Video and
Composite connectors, see
page 9.
Zone 2 and 3 connectors, see
page 9.
Digital connectors
Optical and electrical digital
audio connectors, see page 9.
Aerials, control and communication
Sirius satellite radio, FM/AM/DAB radio, rLead/
rDock, RS232, Network/USB, IR and trigger
connectors, see page 14.
Audio connectors
Two-channel and
multichannel, see page 10.





 














XLR audio output
Balanced XLR connectors for
each of seven channels, to an
XLR-equipped amplier.
For information, see page 47.


E-8
audio/video
connections
Before connecting your AVR600 or AV888 and
power amplier (e.g. the Arcam P777) to your source
components and speakers, please read through the
next few pages which will explain all the input and
output connectivity that is available. e ‘Speakers
section explains how to connect up your speakers to
avoid damage to the amplier and how to arrange your
speakers for best performance.
General
e inputs are named to make it easier to reference
connected devices (e.g. ‘DVD’ or ‘VCR’). ey all have the
same input circuit (with the exception of the ‘PHONO
input), so there is no reason why you should not connect
a dierent device to any of the inputs. For example, if
you had two DVD players and the AV input was not
being used, then the second DVD player could be
connected to the AV input.
When connecting a video source, its audio must be
connected to the corresponding sockets. For example,
if you a had a satellite decoder plugged into a SAT video
input, the audio must be connected to the SAT audio
inputs!
e hierarchy for video connections for best quality is
as follows;
< HDMI
< Component/RGB
< S-Video
< Composite.
You should connect as many of these as possible. e
unit will automatically select the best quality connection
for the source available. For any video source to be
available in Zone 2 you must have an S-Video or
Composite connection between the unit and the source.
Making connections
< Wherever possible, connect both the analogue
and digital outputs of digital sources. is enables
use of a digital input for the main zone and the
corresponding analogue input for recording onto an
analogue tape deck, VCR or PVR, or for the Zone 2
or 3 output.
< Take care to place cables as far from any power
supply cabling as is practicable, to reduce hum and
other noise problems.
HDMI connectors
AV, SAT, DVD, VCR, PVR
Connect the HDMI video outputs of your source equipment to these
corresponding HDMI inputs.
OUT 1
Connect this output to the HDMI video input of your main zone display
device.
OUT 2
Connect this output to the HDMI video input of your second display
device or to another HDMI display device in a second living space. As
the unit has only one processed video path, this signal will be a copy of
the signal on OUT 1.
Important notes about Component/RGB
video inputs and outputs
< When you connect your devices to these
connectors, take care to follow the letter/colour
coding for each input. No damage will occur but
incorrectly coloured or unstable pictures will
result.
< e Component video inputs have sucient
bandwidth for NTSC (525/60) or PAL (625/50)
video and HDTV video signals.
NOTE
All Zone 1 analogue video outputs will be disabled if
an HDMI digital video source is selected.
E-9
English
Zone 3 connectors
Z3 OUT
Connect these analogue audio
outputs to your Zone 3 equipment.
See ‘Multi-room Setup’ on page 48
for information.
Zone 2 connectors
Z2 AUDIO OUT, Z2 VIDEO OUT
Connect these analogue audio
and video outputs to your
Zone 2 equipment. See ‘Multi-
room Setup’ on page 48 for
information.






















 














S-Video and
Composite
connectors
AV, DVD, SAT, VCR, PVR
Connect these inputs to the
S-Video and Composite outputs
of your available source equipment.
VCR OUT, PVR OUT,
ese are recording outputs. Connect these to the
‘S-Video in’ or ‘Composite in’ sockets (usually labelled
RECORD’) on your recording device.
MAIN OUT
Connect this output to the S-Video or Composite
sockets on your primary Zone 1 display.
Component/RGB
video connectors
ese inputs are suitable for
connection to source devices
which output Component (YUV
or YPbPr) or RGB high quality
analogue video signals. ese
signals are usually available from DVD players, set-top
boxes or games consoles.
If you are connecting up to an RGB source you will
also need to connect the sources Composite output to
the units Composite input to act as a video sync. e
Composite signal should be on the same named input as
the RGB signals.
RGB video outputs on source equipment are oen on
SCART connectors. You will need to use a SCART to
‘RGB+Sync on phono’ breakout cable, available from
your Arcam dealer.
NOTE
When setting up the menus (later in this manual),
you will need to select whether the three-wire high
quality video input is Component or RGB for each
input. is is done on the ‘HQ Video In’ line in the
Input Cong menu. Failure to do this can result in a
green looking picture or a picture that is unstable.
AV, DVD, SAT, VCR, PVR
Connect the Component video outputs of your source
equipment to these inputs.
OUT
Connect this output to the Component video input of
your display device.
NOTE
Analogue RGB video output is not available from
the AVR600 or AV888. e analogue three-wire
high quality video output is always congured as
Component video.










Digital audio
connectors
TAPE, CD, AV, DVD, SAT, VCR, PVR
Connect these inputs to the digital
outputs of your available source
equipment.
OPTICAL, COAX
Connect the optical or coaxial output
to your digital recording device such as
CD-R, digital VCR or Minidisc player.
When a digital source is selected,
the digital output will send an exact
copy of the incoming digital signal. For example, for a
5.1 digital source, the digital output will also be in 5.1
format.
When an analogue-only source is selected, this is
digitized by the unit and routed to the digital outputs.
ese outputs are muted if a source is selected where the
HDMI connection is used and is transmitting HD audio.
e digital audio from the HDMI link will not be routed
to these outputs.
E-10

 





Front panel AUX input
e front panel AUX input can be
used as an analogue or optical
digital input.
For analogue sources, use a stereo
3.5mm lead; for digital sources
use a 3.5mm optical lead. e
front input is also used for the
auto-setup microphone input.
















Phono
is input can be connected
directly to a record deck
which has a direct output
from a moving magnet (MM)
cartridge.
MCH input
is multichannel analogue
audio input can be connected to
a source device which outputs
surround sound on its analogue
outputs. Such devices typically
include DVD-Audio and SACD
players. is input does not
pass through any of the audio
processing in the unit, therefore
functions such as speaker size
and distance from the listening
position should be copied from the Setup menus into the
Setup menus of your multichannel source. Note however
that speaker level trims are applied to the MCH input
on the unit. erefore speaker level trim settings on
multichannel source equipment should be le unset at
zero.
Analogue pre-amplifier outputs
All pre-amplier analogue outputs are buered, have a
low output impedance, are at line level and follow the
Zone 1 volume control setting. ey are able to drive
long cables or several inputs in parallel if required.
For more information on connecting speakers or
additional power ampliers, see page 18 and 47.












Analogue record
outputs
VCR OUT, PVR OUT, TAPE OUT
Connect the le and right
outputs to the le and right
input sockets of your cassette
deck, PVR or VCR (usually labelled ‘RECORD’). e PVR
and VCR connectors may be used for a second and third
cassette deck. ese outputs are xed at full line level.
Analogue audio
inputs
TAPE, CD, AV, DVD, SAT, VCR,
PVR
Connect the le and right
inputs to the le and right
outputs of your source
equipment.
Front panel PHONES socket
is socket accepts headphones with an impedance
rating between 32Ω and 600Ω, tted with a 3.5mm
stereo jack plug. e headphone socket is always active,
except when AVR600 is muted.
When the headphone jack is inserted, the speaker
outputs and analogue pre-amplier outputs are
automatically muted.
E-11
English
E-12































































    



 



















 



































Connection guide
DVD player
e diagram shows how to make audio and video
connections from a typical DVD player.
e preferred video hook-up, in order of preference is:
<
use the HDMI connector (if HDMI output is
provided by the player), otherwise connect the three
Component or four RGB+Sync video connectors.
<
use the S-Video connection if HDMI or Component
/RGB+Sync outputs are not provided by your player.
<
use the Composite connection if HDMI,
Component/RGB+Sync or S-Video are not provided
by your player.
In each case, connect the video inputs labelled DVD on
the unit.
e preferred audio hook-up is using the coaxial digital
connector (usually marked DIGITAL AUDIO OUT), in
addition to the coaxial analogue outputs for le and
right channels.
In each case, use the audio inputs labelled DVD on the
unit.
Satellite receiver
A satellite receiver is connected in the same way as
a DVD player, with the same order of preference
according to the outputs provided by the satellite
receiver.
In each case, use the inputs labelled SAT on the unit.
Note that digital audio input from a satellite receiver
sometimes requires a coaxial/TOSLINK (digital
connector) interconnect cable, as some satellite receivers
do not implement audio over HDMI properly or at all.
CD player
Connect the digital audio output (if provided by the CD
player) to the digital CD input of the unit, using a high
quality coaxial interconnect cable.
Connect the right and le analogue audio outputs of the
CD player to the analogue CD inputs of the unit, using a
pair of high quality coaxial interconnect cables.

E-13
English









































     





Connecting an iPod using the Arcam rDock
e combination of the AVR600 or AV888 and Arcams
optional rDock or rLead accessory provides a great
platform for your iPod.
Connect the rDock as shown, power on the rDock, slot
in your iPod and select iPod as the source. For video
connections, select the video source you have used for
the iPod input in the ‘Video Inputs’ menu.
Navigating through music and podcasts on your iPod is
simple using the CR102 remote, with text appearing on
the front panel display.
More information is given in the rDock quick start
guide (or rLead quick start guide) supplied with these
accessory units.
E-14
radio
connectors









 



NOTE
e AVR600 provides power for the Sirius receiver,
so an external power supply is not needed.
Aerial connectors – AVR600 only
e AVR600 is tted with an AM/FM receiver module
and Sirius connector or a DAB/FM receiver, depending
on the region where it was sold. e type of aerial you
need depends on your listening preferences and the
local conditions.
Your AVR600 is capable of superb radio reception, but
only if it is receiving a good quality transmission signal.
Try the aerials supplied with your unit. If you are in a
medium to strong signal area, these should be adequate
for good reception. In areas with poor signal strength,
you may require a roof or lo mounted aerial.
Contact your local Arcam dealer or aerial installation
experts for advice about local reception conditions.
Sirius
(where tted)
e AVR600 is designed for use
with the SiriusConnect™ Home
Tuner’ package which should be
connected via the cable supplied in
that package to the Sirius socket.
Listening to Satellite Radio
To listen to Satellite Radio, you’ll
need to connect either a SIRIUS
or XM Satellite Radio tuner (sold separately) to your
satellite-ready receiver. Satellite Radio is available to
residents of the US (except Alaska and Hawaii) and
Canada.
Satellite Radio delivers a variety of commercial-free music
from categories ranging from Pop, Rock, Country, R&B,
Dance, Jazz, Classical and many more plus coverage of
all the top professional and college sports including play
by play games from select leagues and teams. Additional
programming includes expert sports talk, uncensored
entertainment, comedy, family programming, local trac
and weather and news from your most trusted sources.
Whether you purchase a SIRIUS or XM tuner, you’ll
need to activate and subscribe to begin enjoying the
service. Easy to follow installation and setup instructions
are provided with the satellite tuners. Whichever service
you choose, there are a variety of programming packages
available, including the option of adding “e Best of
SIRIUS” programming to your XM tuner or “e Best
of XM” programming to your SIRIUS tuner, enabling
you to enjoy the most popular programming among
both services. e “Best of” packages are not available to
SIRIUS or XM Canada subscribers at this time.
Family friendly packages are also available to restrict
channels featuring content that may be inappropriate for
children.
To subscribe to XM, U.S. customers should visit
www.xmradio.com or call 1-800-XMRADIO
(1-800-967-2346); Canadian customers should
visit www.xmradio.ca or call XM Listener Care at
1-877-GETXMSR (1-877-438-9677).
To subscribe to SIRIUS, U.S. and Canadian customers
can call 1-888-539-SIRI (1-888-539-7474) or visit
www.sirius.com (US) or www.siriuscanada.ca (Canada).








 













 



DAB
(where tted)
In strong signal areas,
the DAB ‘T’ ribbon aerial
supplied can be used with
reasonable results. Mount
the aerial as high up as
possible on a wall.
In the UK the ‘T’-elements
need to be positioned
vertically for DAB
reception since broadcasts
are vertically polarised. In
other localities, check with
your Arcam dealer or try
both horizontal and vertical positions for best
reception.
Try each usable wall of the room to see which
gives best reception and use tacks or adhesive
tape to secure the aerial in a ‘T’ shape, but note
that no tacks should come into contact with the
internal wire of the aerial.
When installed and receiving
DAB, check the signal
strength by pressing the front
panel or remote control’s INFO
button until the signal quality
indicator is displayed.
In weak signal areas, a high-
gain, externally-mounted
or roof-mounted aerial is
desirable in order to receive
the highest number of services.
In Band III transmission areas
(such as the UK), use a multi-
element Yagi aerial with the
elements mounted vertically, as
the transmissions are vertically
polarised. If you are close to
more than one transmitter, use
an omnidirectional or folded
dipole aerial.
If the DAB services in your
area are transmitted on L-band,
then ask your dealer for advice
for the best aerial to use.

E-15
English
FM
Connecting an aerial
A suitable FM aerial must be
connected to the AVR600 before
FM radio can be received.
In strong signal areas, the FM
ribbon aerial supplied can be
used with reasonable results.
Mount this as high up as
possible on a wall with the top
of the ‘T’-elements positioned
vertically or horizontally, depending on the reception in
your area. Try each usable wall of the room to see which
gives best reception and use tacks or adhesive tape to
secure the aerial, but note that no tacks should come
into contact with the internal wire of the aerial.
When installed and receiving FM radio, check the signal
strength by pressing the front panel or remote controls
INFO button until the signal indicator is displayed.
In weak signal areas, or for optimal FM radio reception,
a roof- or lo-mounted aerial is advised as this will give
superior reception.
In some areas, cable radio may be available or, in an
apartment building, a distributed aerial system may
be installed. In either of these cases you should have
sockets in your home marked FM or VHF (do not use
those marked TV); these should be connected to the FM
coaxial connector on the rear of the AVR600.
AM
Connecting an aerial
An AM aerial is required to
receive AM/medium wave radio
signals, so a simple loop aerial is
supplied with the AVR600. Follow
the assembly instructions in the
diagram below.
Make sure that the aerial is
positioned well away from the
AVR600 itself, TVs, computers
and other sources of RF ‘interference. Rotate the aerial
to discover which position gives the best reception.
2. Push the tab into the open slot in the
base of the stand. Press until the tab
clicks home.
3. Connect the lead wires to the AM socket
at the rear of the AVR600 (the wires are
not polarised). Rotate the aerials stand
until you obtain the best reception.
1. Release the tie-wrap and unwind the
twisted lead. Fold the plastic stand
forward through the loop frame.









 











 




E-16
other
connectors
Data connectors
rLead/rDock
For use with an Arcam rLead or
rDock accessory. See page 13 and
the accessory documentation for
details.
RS232 serial connector
Use with control devices having
an RS232 serial port (for example,
Crestron and AMX touch screen
controllers). is connection
is also used for upgrading the
AVR600 or AV888’s internal
soware.
Network connectors
is section deals with installation of the unit into an
existing home network. For information on how to use
the units network features, the USB socket, and for a list
of supported le types, refer to page 46.
Networking is a large subject and only the briefest
guidelines are presented in this handbook. Please
contact your Arcam dealer or specialist installer for
more information about introducing the AVR600 or
AV888 into your computer network.
Ethernet
If an Ethernet cable is connected, the unit will
automatically attempt to connect to your network.
You should use CAT5 cable plugged into the RJ45 socket
labelled ETHERNET on the rear panel.
If your network uses static IP
addressing rather than DHCP,
you will need to provide any
gateway, DNS and proxy
information. See page 39 for
information on setting up the
network.
USB connector
e AVR600 and AV888 can play
les stored on a USB mass storage
device, typically a pen drive, but
any USB device that complies
with the ‘mass storage device‘
class is compatible.
e unit only supports the direct
connection of USB devices
and will not support devices
connected through a hub. If
regular access to the USB socket is required, you may
nd it convenient to use a USB extension lead.
See page 46 for details of supported le types.








 













 












 












 








 





E-17
English
Trigger connectors
e trigger connectors (TRIG Z1, TRIG Z2 and TRIG Z3)
provide an electrical signal whenever the amplier is
switched on and the relevant zone enabled.
e trigger signal can be used
to switch on and o compatible
pieces of home entertainment
equipment, for example, you
could set up a trigger to turn on
your television and DVD player
whenever the unit was switched
on.
ere are three trigger output
sockets on the unit, each capable
of outputting a 12V, 70mA
switching signal. e socket
is designed for mono 3.5mm jacks: tip is the trigger
output, sleeve is ground.
tip: Trigger output
sleeve: Ground
TRIG Z1
Use for remotely turning on and o power amps or
source equipment for Zone 1. On = 12V, O = 0V.
TRIG Z2
Use for remotely turning on and o power amps or
source equipment for Zone 2. On = 12V, O = 0V.
Infra-red (IR) connectors
e infra-red inputs (Z1 IR, Z2 IR
and Z3 IR) allow the connection of
external IR receivers, either when
the units front panel IR receiver is
fully or partially obstructed or to
allow the use of a remote control
in Zone 2 or Zone 3.
ere are three IR inputs on the
unit, each designed for stereo or
mono 3.5mm jacks. Tip is the
modulated signal, sleeve is ground.
tip: Modulated signal
sleeve: Ground
Z1 IR
is input is intended for use with a local IR receiver
when the front panel of the unit is blocked.
Connecting an IR receiver to Z1 IR will disable to front
panel IR receiver to prevent problems with multiple
commands if the front panel IR receiver is only partially
obstructed.
Z2 IR
is input is intended for use with an IR receiver in
Zone 2 to allow remote control of the unit from a second
room.




























Z3 IR
is input is intended for use with an IR receiver in
Zone 3 to allow remote control of the unit from a third
room.
IR OUT
is output is an electrical combination of the Z1 (or
front panel) + Z2 + Z3 infra-red signals above. It can be
used to drive external IR emitters or can be connected
directly to other Arcam equipment which have an IR
input. is function can be useful as an IR ‘repeater
so that someone in any of the zones can control the
functions of a CD player in the main zone, for example.
Tip is the modulated electrical IR signal, sleeve is
ground.
A supplier of infra-red receivers and emitter accessories
and systems is Xantech. See www.xantech.com for
more information, or ask your Arcam dealer.
NOTE
e IR inputs on the unit are designed for
modulated signals. If the external IR receiver
demodulates the IR signal, it will not work. Also the
unit does not provide power for external receivers
on the IR jack, therefore an external power source
will be required.
TRIG Z3
Use for remotely turning on and o power amps or
source equipment for Zone 3. On = 12V, O = 0V.
NOTE
Sockets with the prex ‘Z2’ or ‘Z3’ refer to
connections used in multi-room installation. For
more information on these connectors, see page 48.
E-18
speakers
Connecting speakers
– AVR600 only
e AVR600 allows you to connect up to seven speakers
and three active subwoofers in the main system. e
output channels correspond to speakers installed in the
front le, centre, front right, surround le, surround
right, surround back le, surround back right and an
active subwoofer.
e conguration and placement of your speakers
is very important. All speakers, with the exception of
the subwoofer, should be arranged around your normal
viewing/listening position. e subwoofer should be
placed in a position which gives an even frequency
response in all listening positions. Incorrect placement
leads to bass boom in some areas. Oen the only
way to nd a good position for your subwoofer is by
experimentation. A good place to start experimenting
is close to a wall but at least 1m away from any corners.
You can also consult your subwoofer handbook for
placement suggestions.

To connect each of the
speakers, unscrew the
corresponding terminals on
the back of the AVR600, insert
the speaker wires through
the hole in each post and
screw the terminals back
up. Make sure that the red
(positive/+) terminal of the
speaker is connected to the
red (positive/+) terminal on
the back panel, and the black
(negative/) terminal of the
speaker is connected to the
black (negative/) terminal on
the back panel.
It is important that no stray
strands of wire from these
connections are allowed to
touch another cable or the product casing. Failure to
ensure this can cause a short circuit and damage your
AVR600.
Do not over-tighten the loudspeaker terminals, or use a
wrench, pliers, etc., as this could damage the terminals
and this would not be covered under the products
warranty.
Connecting subwoofers
e AVR600 and the AV888 allow
up to three active subwoofers to be
connected to the SW1, SW2 or SW3
outputs.
See your subwoofer handbook
for the correct setting up and
connection for your particular
subwoofer.
Speaker cables
e speakers should be connected to the amplier using
good-quality, high-purity, low impedance copper cables.
Cheap speaker cables should be avoided – they are a
false economy and can signicantly degrade the sound
quality.
e cable runs to the speakers should be as short as
practicable. Connections to the speaker terminals
should always be nger tight, whether using bare wires
or spade connectors.


















  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68

Arcam AVR600 User manual

Category
AV receivers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI