Renkforce Controller PC, iOS, Android Owner's manual

Brand: Renkforce

Model: Controller PC, iOS, Android

Type: Owner's manual

Page is loading ...

b) Batteries

• Check that the batteries are inserted with the correct polarity.

• To prevent battery leakage, remove the batteries when you do not plan to use

the product for an extended period. Leaking or damaged batteries may cause

acid burns if they come into contact with your skin. Always use suitable protective

gloves when handling damaged batteries.

• Batteries must be kept out of the reach of children. Do not leave batteries lying

around, as there is a risk that children or pets may swallow them.

• All batteries must be replaced at the same time. Mixing old and new batteries can

cause the batteries to leak and damage the product.

• Batteries must not be dismantled, short-circuited or thrown into ames. Never

recharge non-rechargeable batteries. Danger of explosion!

Product overview

1 B button

2 A button

3 X button

4 START button

5 button

6 button

7 (On/Off) button

8 LED

9 GAME KEY slide switch

10 button

11 Joystick

12 button

13 SELECT button

14 Battery compartment cover

15 Y button

Operation

a) Replacing the batteries

• The enclosed batteries must be inserted before the device can be used.

• To insert the batteries, remove the battery compartment cover (14) from the rear of the

product. To do this, lightly press the locking tab and slide in the direction of the arrow. Open

the battery compartment cover outwards.

• Insert two 1.5 V batteries with correct polarity into the battery compartment (batteries are

enclosed). Always observe the correct polarity (positive/+ and negative/-). The battery

compartment is not marked. The spring contact is the negative/- terminal, the positive/+

terminal is the opposite contact.

• Replace the battery compartment cover (14) and ensure that the locking tab clicks into place

when pressed.

If you need to replace the batteries at a later point in time, repeat this procedure but

remove the old batteries rst.

b) Switching on and off

• Press and hold the button (7) until the LED (8) lights up. After a short period, the LED

begins to ash. The device is ready to pair with a Bluetooth device.

• If the controller is already connected to a Bluetooth device, the LED (8) ashes at longer

intervals (approx. every 9 seconds). This indicates the Bluetooth connection.

• Press and hold the button (7) until the LED (8) ashes several times and then goes out.

The device is switched off.

• All button and switch activity is indicated by the LED (8) lighting up. This only applies if there

is Bluetooth connection to a device.

• If not used for an extended period of time, the controller switches off automatically in order to

save energy. If there is no Bluetooth connection, the controller switches off after 5 minutes.

If there is a Bluetooth connection, the controller switches off automatically after 30 minutes.

c) Pairing with a Bluetooth device

• Press and hold the button (7) until the LED (8) ashes quickly to put the controller into

pairing mode.

• Bring your Bluetooth-enabled device within range of the controller.

• Activate the Bluetooth function on the device that you wish to pair. Please also note the

operating instructions of the device. Follow the instructions to pair. The device ID of the

controller is “RC-B01”.

• The fast ashing of the LED (8) stops as soon as the controller is paired with a Bluetooth

device. The LED (8) then ashes approx. every 9 seconds.

If the LED (8) only ashes every 9 seconds after the device is switched back on, the

controller is already connected to a Bluetooth device.

• To connect the controller to the last paired Bluetooth device, press and hold the

button (7) for 2 seconds.

Operating instructions

VR CONTROLLER RF-VR-CO1

Item no. 1628568

Intended use

The product is designed as an input device (such as a computer mouse) for mobile devices,

apps for virtual reality glasses such as, for example, for Google Cardboard, as well as for

tablet computers and PCs. Android, iOS and Windows operating systems are supported. It is

especially suitable for multimedia applications and supports video switchover, volume control

and other control functions. Communication between the controller and the connected device

takes place wirelessly via Bluetooth. The controller is powered by two 1.5 V batteries (AAA).

This product is intended for indoor use only. Do not use it outdoors. Contact with moisture (e.g.

in bathrooms) must be avoided under all circumstances.

For safety and approval purposes, you must not rebuild and/or modify this product. Using

the product for purposes other than those described above may damage the components. In

addition, improper use can cause hazards such as a short circuit or re. Read the instructions

carefully and store them in a safe place. Only make this product available to third parties

together with its operating instructions.

This product complies with statutory national and European regulations. All company and

Package contents

• Controller

• 2x AAA batteries

• Operating instructions

Up-to-date operating instructions

To download the latest operating instructions, visit www.conrad.com/downloads or scan the QR

code on this page. Follow the instructions on the website.

Explanation of symbols

The symbol with an exclamation mark in a triangle is used to highlight important

information in these operating instructions. Always read this information carefully.

The arrow symbol alerts the user to the presence of important tips and notes on

using the device.

Safety instructions

Read the operating instructions and safety information carefully. If you do

not follow the safety information and information on proper handling in these

operating instructions, we will assume no liability for any resulting personal

injury or damage to property. Such cases will invalidate the warranty/

guarantee.

a) General information

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. It may become a

dangerous toy for children.

• Protect the product from extreme temperatures, direct sunlight, strong jolts, high

humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, stop using it and prevent

unauthorised use. Safe operation can no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stress.

• Always handle the product carefully. Jolts, impacts or a fall even from a low height

may damage the product.

• Consult a technician if you are not sure how to use or connect the product, or if

you have concerns about safety.

• Maintenance, modications and repairs must be carried out by a technician or a

specialist repair centre.

• If you have questions which remain unanswered by these operating instructions,

contact our technical support service or other technical personnel.

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming or capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

d) “KEY” setting

Select the type of function with the GAME KEY slide switch (9). In the “KEY” position, you

can operate your mobile device or other device such as with a mouse and some additional

functions.

• Move the GAME KEY slide switch (9) to the “KEY” position. The descriptions in the

subsections below are functions of KEY mode.

Mouse function (only for Android and PC)

Button Function

Joystick (11) Change the position of the mouse pointer

START button (4) Function as left mouse button

SELECT button (13) Function as right mouse button

(On/Off) button (7)

Function as “Enter” button if the device is switched on

button (6) Catalogue button for calling the menu

On-screen keyboard

• The virtual keyboard does not work with the iOS operating system.

• For the Android operating system, install the Android keyboard via Google Play.

Audio and video playback

Open the music player on your mobile device. After starting playback, you can control playback

with the controller: pause, open other titles, etc.

Button Multimedia function

B button (1) Decrease the volume

X button (3) Increase the volume

button (5)

Play/pause

button (10)

Forward

button (12)

Reverse

A button (2) Fast rewind

Y button (15) Fast forward

With the large number of Bluetooth devices and operating system versions (e.g.

on different smartphone models), it may be that some models do not support the

multimedia functions of this controller, do not do so correctly, or do so only in a

different manner or not fully.

e) Camera operation

Button Function

iOS Start the camera app on your mobile device, if necessary.

Press the X button (3) (shutter release) to take a photo.

Android Start the camera app on your mobile device, if necessary.

Press the X button (3) or B button (1) (shutter release) to take

a photo.

button (5)

Play/pause

button (10)

Forward

With the large number of Bluetooth devices and operating system versions (e.g.

on different smartphone models), it may be that some models do not support the

camera functions of this controller, do not do so correctly, or do so only in a different

manner or not fully. The X or B buttons may, in certain circumstances, increase the

magnication (zoom).

f) Other buttons

Button Function

button (7)

This button is used to switch back to the previous display

when the controller is switched on.

g) “GAME” setting

• If the GAME KEY slide switch (9) is in the “GAME” position, the controller is in game mode.

• The functions of the individual buttons are then dependent on the programming of the

respective video game. Test the assignments and functions accordingly. Video games and

apps can be operated according to your programming. Test the button functions for the

respective application.

• In the “GAME” position, it may be that the controller buttons do not function fully.

• In iOS, the cursor is not available.

Care and cleaning

• Before cleaning the product, disconnect it from the power supply (remove the batteries).

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may

damage the casing or cause the product to malfunction.

• Use a dry, lint-free cloth to clean the product.

Declaration of Conformity (DOC)

Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declares that this

product conforms to Directive 2014/53/EU.

Click on the following link to read the full text of the EU Declaration of Conformity:

www.conrad.com/downloads

Select a language by clicking on the corresponding ag symbol and then enter

the product order number in the search box. The EU Declaration of Conformity is

available for download in PDF format.

Disposal

a) Product

Electronic devices are recyclable waste and must not be disposed of in the

household waste. Always dispose of the product according to the relevant statutory

regulations.

Remove any inserted batteries and dispose of them separately from the product.

b) Batteries

You are required by law to return all used batteries (Battery Directive). Batteries

must not be placed in household waste.

Batteries containing hazardous substances are labelled with this symbol to indicate

that disposal in household waste is forbidden. The abbreviations for heavy metals

in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (indicated on the battery,

e.g. below the waste bin icon on the left).

Used batteries can be returned to local collection points, our stores or battery retailers.

You thus full your statutory obligations and contribute to protection of the environment.

Technical data

Power supply ................................ 2x 1.5 V batteries (Micro/AAA)

Operating voltage/current ............. 3 V/DC, 0.5 to 8 mA

Suitable for .................................. Android/iOS mobile devices/PC

Battery life ..................................... 20 to 40 hours

Frequency band ............................ 2.4 to 2.48 GHz

Transmission power...................... 5 dBm

Bluetooth version .......................... 3.0

Range ........................................... approx. 2 to 10 m

Supported systems ....................... Windows

2000, XP (Home, Pro with SP1, SP2, SP3)

(32 Bit), Vista™ (64 Bit), 7 (32/64 Bit), 8.0 (32/64 Bit),

8.1 (32/64 Bit), 10.0/S (32/64 Bit), Android 4.12 - 7.0,

iOS 8.0 - 10.1, Windows Phone

Operating conditions ..................... +10 to +50 °C, 10 - 85 % relative humidity (non-

condensing)

Storage conditions ........................ -20 to +60 °C, 10 - 95 % relative humidity (non-

condensing)

Dimensions (L x W x H) .............. 100 x 40 x 27 mm

Weight .......................................... 55 g (with batteries)

Page is loading ...

Renkforce Controller PC, iOS, Android Owner's manual

Brand: Renkforce

Model: Controller PC, iOS, Android

Type: Owner's manual

Download PDF

report

in other languages

français: Renkforce Controller PC, iOS, Android Le manuel du propriétaire
Deutsch: Renkforce Controller PC, iOS, Android Bedienungsanleitung
Nederlands: Renkforce Controller PC, iOS, Android de handleiding

Renkforce Controller PC, iOS, Android Owner's manual

Renkforce Controller PC, iOS, Android Owner's manual

in other languages

Related papers

Other documents