Cisco WS-C2960G-24TC-LOB Datasheet

Category
Network switches
Type
Datasheet

This manual is also suitable for

Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 1 of 21
Cisco Catalyst 2960 Series Switches with LAN Base
Software
Cisco
®
Catalyst
®
2960 Series Switches with LAN Base software are a family of fixed-
configuration, standalone intelligent Ethernet devices with Power Over Ethernet (PoE) or
non-PoE configurations that provide desktop Fast Ethernet and Gigabit Ethernet
connectivity, enabling enhanced LAN services for entry-level enterprise, midmarket, and
branch office networks (See Figure 1). The Cisco Catalyst 2960 LAN Base Series offers
integrated security, including Network Admission Control (NAC), advanced quality of
service (QoS), and resiliency to deliver intelligent services for the network edge.
The Cisco Catalyst 2960 LAN Base Series offers:
PoE configurations up to 48 ports
Intelligent features at the network edge, such as sophisticated access control lists (ACLs)
and enhanced security
Networked Sustainability: Cisco EnergyWise to measure, report and reduce energy usage
across the entire organization
Dual-purpose uplinks for Gigabit Ethernet uplink flexibility, allowing use of either a copper
or a fiber uplink; each dual-purpose uplink port has one 10/100/1000 Ethernet port and one
Small Form-Factor Pluggable (SFP)-based Gigabit Ethernet port, with one port active at a
time
Network control and bandwidth optimization using advanced QoS, granular rate limiting,
ACLs, and multicast services
Network security through a wide range of authentication methods, data encryption
technologies, and NAC based on users, ports, and MAC addresses
Easy network configuration, upgrades, and troubleshooting using Cisco Network Assistant
software
Autoconfiguration for specialized applications using Auto Smartports
Limited lifetime hardware warranty
Software updates at no additional charge
Figure 1. Cisco Catalyst 2960 Series Switches
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 2 of 21
Configurations
The Cisco Catalyst 2960 LAN Base Series includes the following switches (Table 1):
Table 1. Switch Configurations of Cisco Catalyst 2960 LAN Base Switches
Feature Description
Cisco Catalyst 2960PD-8TT-L 8 Ethernet 10/100 ports and 1 10/100/1000 PoE input port; compact size with no fan
Cisco Catalyst 2960-8TC-L 8 Ethernet 10/100 ports and 1 dual-purpose uplink port (10/100/1000 or SFP); compact size
with no fan
Cisco Catalyst 2960-24TT-L 24 Ethernet 10/100 ports and 2 fixed Ethernet 10/100/1000 uplink ports
Cisco Catalyst 2960-48TT-L 48 Ethernet 10/100 ports and 2 fixed Ethernet 10/100/1000 uplink ports
Cisco Catalyst 2960-24LT-L 24 Ethernet 10/100 ports (PoE supported on 8 ports) and 2 fixed Ethernet 10/100/1000
uplink ports
Cisco Catalyst 2960-24PC-L 24 Ethernet 10/100 PoE ports and 2 dual-purpose uplink ports
Cisco Catalyst 2960-48PST-L 48 Ethernet 10/100 PoE ports with 2 fixed Ethernet 10/100/1000 uplinks and 2 SFP uplinks
ports
Cisco Catalyst 2960-24TC-L 24 Ethernet 10/100 ports and 2 dual-purpose uplink ports
Cisco Catalyst 2960-48TC-L 48 Ethernet 10/100 ports and 2 dual-purpose uplink ports
Cisco Catalyst 2960G-8TC-L 8 Ethernet 10/100/1000 ports, 1 of which is dual-purpose; compact size with no fan
Cisco Catalyst 2960G-24TC-L 24 Ethernet 10/100/1000 ports, 4 of which are dual-purpose
Cisco Catalyst 2960G-48-TC-L 48 Ethernet 10/100/1000 ports, 4 of which are dual-purpose
The Cisco Catalyst 2960 LAN Base software image is a rich suite of intelligent services, including
advanced QoS, rate limiting, ACLs, and IPv6 management. The SFP-based Gigabit Ethernet ports
accommodate a range of SFP transceivers, including the Cisco 1000BASE-SX, 1000BASE-LX,
1000BASE-BX, 1000BASE-ZX, 100BASE-FX, 100BASE-LX, 100BASE-BX, and coarse
wavelength-division multiplexing (CWDM) SFP transceivers.
Cisco EnergyWise Technology: Good for Business, Better for Environment
Cisco EnergyWise is an innovative architecture, added to the Cisco Catalyst 2960 switches, that
enable the measurement of power consumption in the network infrastructure and network attached
devices. EnergyWise encompasses a highly intelligent network based approach to communicate
messages that measure and control energy between network devices and end points. The network
discovers Cisco EnergyWise manageable devices, monitors their power consumption, and takes
action based on business rules to reduce power consumption. EnergyWise uses a unique domain
naming system to query and summarize information from large sets of devices making it simpler
than traditional network management capabilities. Cisco EnergyWise’s management interfaces
allow facilities and network management applications to communicate with end points and each
other using the network as a unifying fabric. The management interface uses standard SNMP or
SSL to integrate Cisco and third party management systems.
Cisco EnergyWise extends the network as a platform for power control plane for gathering,
managing and reducing power consumption of all devices, resulting in company-wide optimized
power delivery and reduced energy costs. Together, Cisco EnergyWise technology and Catalyst
switches enable Greenhouse Gas (GhG) emissions reduction, increased energy cost savings and
sustainable business behavior.
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 3 of 21
Power over Ethernet
The Cisco Catalyst 2960 Series provide PoE to allow easy connectivity to Ethernet-powered
devices including Cisco IP phones and wireless access points. Cisco Catalyst 2960 PoE models
comply with Cisco pre-standard PoE and IEEE 802.3af. PoE removes the need for wall power to
each PoE-enabled device and eliminates the cost for additional electrical cable and circuits that
would otherwise be necessary in IP phone and WLAN deployments. PoE switches also eliminate
the need for power injectors and PoE mid-spans for powering IP devices. The Cisco Catalyst
2960-48PST-L can support 48 PoE ports with total PoE power output capacity at 370W. Taking
advantage of Cisco Catalyst Intelligent Power Management, the Cisco Catalyst 2960-48PST-L
configuration can deliver the necessary power to support 24 ports at 15.4W, 48 ports at 7.7W, or
any combination in between. Cisco Catalyst 2960-24PC-L can support 24 simultaneous full-
powered PoE port at 15.4W. The Cisco Catalyst 2960-24LT-L has 24 10/100 ports with 8
simultaneous full-powered PoE ports at 15.4W.
The Cisco Catalyst 2960-8TT-L has eight 10/100 ports with one 10/100/1000 PoE input port. This
switch does not need a power supply and receives power over the uplink from an upstream PoE
device, providing deployment flexibility and availability. It is ideal for wiring and space-constraint
applications. The power adaptor (PWR-A=) and power cord are optional and may be ordered
separately.
Gigabit Ethernet
At speeds of 1000 Mbps, Gigabit Ethernet provides the bandwidth to meet new and evolving
network demands, alleviate bottlenecks, and boost performance while increasing the return on
existing infrastructure investments. Today’s workers are placing higher demands on networks,
running multiple concurrent applications. For example, a worker joins a team conference call
through an IP videoconference, sends a 10-MB spreadsheet to meeting participants, broadcasts
the latest marketing video for the team to evaluate, and queries the customer relationship
management (CRM) database for the latest real-time feedback. Meanwhile, a multigigabyte
system backup starts in the background and the latest virus updates are delivered to the client.
Redundant Power System
The Cisco Catalyst 2960 Series Switches support the new generation of the Cisco Redundant
Power System (RPS) 2300, which increases availability in a converged data, voice, and video
network by providing transparent power backup to two of six attached switches at the same time.
Intelligence in the Network
Networks of today are evolving to address four new developments at the network edge:
Increase in desktop computing power
Introduction of bandwidth-intensive applications
Expansion of highly sensitive data on the network
Presence of multiple device types, such as IP phones, WLAN access points, and IP video
cameras
These new demands contend for resources with existing mission-critical applications. As a result,
IT professionals must view the edge of the network as critical to effectively manage the delivery of
information and applications.
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 4 of 21
As companies increasingly rely on networks as their strategic business infrastructure, it is more
important than ever to help ensure their high availability, security, scalability, and control. By
adding Cisco intelligent functions for LAN access, you can now deploy networkwide intelligent
services that consistently address these requirements from the desktop to the core and through
the WAN.
Cisco Catalyst Intelligent Ethernet switches help you realize the full benefits of adding intelligent
services into your networks. Deploying capabilities that make the network infrastructure highly
available to accommodate time-critical needs, scalable to accommodate growth, secure enough to
protect confidential information, and capable of differentiating and controlling traffic flows is critical
to further optimizing network operations.
Enhanced Security
The wide range of security features that the Cisco Catalyst 2960 LAN Base Series offers helps you
protect important information, keep unauthorized people off the network, guard privacy, and
maintain uninterrupted operation.
The Cisco Identity-Based Networking Services (IBNS) solution provides authentication, access
control, and security policy administration to secure network connectivity and resources. Cisco
IBNS in the Cisco Catalyst 2960 LAN Base Series prevents unauthorized access and helps ensure
that users get only their designated privileges. It provides the ability to dynamically administer
granular levels of network access. Using the 802.1x standard and the Cisco Secure Access
Control Server (ACS), users can be assigned a VLAN upon authentication, regardless of where
they connect to the network. This setup allows IT departments to enable strong security policies
without compromising user mobility and with minimal administrative overhead.
To guard against denial-of-service (DoS) and other attacks, ACLs can be used to restrict access to
sensitive portions of the network by denying packets based on source and destination MAC
addresses, IP addresses, or TCP/User Datagram Protocol (UDP) ports. ACL lookups are done in
hardware, so forwarding performance is not compromised when ACL-based security is
implemented.
Port security can be used to limit access on an Ethernet port based on the MAC address of the
device to which it is connected. It also can be used to limit the total number of devices plugged into
a switch port, thereby protecting the switch from a MAC flooding attack as well as reducing the
risks of rogue wireless access points or hubs.
With Dynamic Host Configuration Protocol (DHCP) snooping, DHCP spoofing can be thwarted by
allowing only DHCP requests (but not responses) from untrusted user-facing ports. Additionally,
the DHCP Interface Tracker (Option 82) feature helps enable granular control over IP address
assignment by augmenting a host IP address request with the switch port ID.
The MAC Address Notification feature can be used to monitor the network and track users by
sending an alert to a management station so that network administrators know when and where
users entered the network. Secure Shell Protocol Version 2 (SSHv2) and Simple Network
Management Protocol Version 3 (SNMPv3) encrypt administrative and network-management
information, protecting the network from tampering or eavesdropping. TACACS+ or RADIUS
authentication enables centralized access control of switches and restricts unauthorized users
from altering the configurations. Alternatively, a local username and password database can be
configured on the switch itself. Fifteen levels of authorization on the switch console and two levels
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 5 of 21
on the Web-based management interface provide the ability to give different levels of configuration
capabilities to different administrators.
Intelligent PoE Management
The Cisco Catalyst 2960 PoE models support Cisco IP phones and Cisco Aironet
®
wireless LAN
access points, as well as any IEEE 802.3af-compliant end device.
Cisco Discovery Protocol version 2 allows the Cisco Catalyst 2960 Series Switch to
negotiate a more granular power setting when connecting to a Cisco powered device, such
as IP phones or access points, than what is provided by IEEE classification.
The PoE MIB provides proactive visibility into power usage and allows you to set different
power level thresholds.
Link Layer Discovery Protocol (LLDP and LLDP-MED) adds support for IEEE 802.1AB link
layer discovery protocol for interoperability in multivendor networks. Switches exchange
speed, duplex, and power settings with end devices such as IP phones.
Availability and Scalability
The Cisco Catalyst 2960 LAN Base Series is equipped with a large set of features that allow for
network scalability and higher availability through multicast filtering as well as a complete suite of
Spanning Tree Protocol enhancements aimed to maximize availability in a Layer 2 network.
Voice-aware 802.1x port security disables the offending data VLAN when a violation is detected
without affecting Voice VLAN on the same switch port. Enhancements to the standard Spanning
Tree Protocol, such as Per-VLAN Spanning Tree Plus (PVST+), UplinkFast, and PortFast help
maximize network uptime. PVST+ allows for Layer 2 load sharing on redundant links to efficiently
use the extra capacity inherent in a redundant design. UplinkFast, PortFast, and BackboneFast all
greatly reduce the standard 30- to 60-second Spanning Tree Protocol convergence time. Flexlink
provides bidirectional, fast convergence in less than 100 milliseconds. The Loopguard and bridge
protocol data unit (BPDU) guard enhancements provide Spanning Tree Protocol loop avoidance.
Advanced QoS
The Cisco Catalyst 2960 LAN Base Series offers superior multilayer QoS features to help ensure
that network traffic is classified and prioritized and that congestion is avoided in the best possible
manner. Configuration of QoS is greatly simplified through automatic QoS (Auto QoS), a feature
that detects Cisco IP phones and automatically configures the switch for the appropriate
classification and egress queuing. This optimizes traffic prioritization and network availability
without the challenge of a complex configuration.
The Cisco Catalyst 2960 LAN Base Series can classify, reclassify, police, mark, queue, and
schedule incoming packets and can queue and schedule packets at egress. Packet classification
allows the network elements to discriminate between various traffic flows and enforce policies
based on Layer 2 and Layer 3 QoS fields.
To implement QoS, the Cisco Catalyst 2960 LAN Base Series Switch first identifies traffic flows or
packet groups, then classifies or reclassifies these groups using the differentiated services code
point (DSCP) field or the 802.1p class of service (CoS) field. Classification and reclassification can
be based on criteria as specific as the source or destination IP address, source or destination
MAC address, or the Layer 4 TCP or UDP port. At the ingress, the Cisco Catalyst 2960 LAN Base
Series also polices to determine whether a packet is in or out of profile, marks to change the
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 6 of 21
classification label, passes through or drops out of profile packets, and queues packets based on
classification. Control-plane and data-plane ACLs are supported on all ports to help ensure proper
treatment on a per-packet basis.
The Cisco Catalyst 2960 LAN Base Series supports four egress queues per port, giving network
administrators more control in assigning priorities for the various applications on the LAN. At
egress, the switch performs congestion control and scheduling, the algorithm or process that
determines the order in which queues are processed. The Cisco Catalyst 2960 LAN Base Series
Switch supports Shaped Round Robin (SRR) and strict priority queuing. The SRR algorithm helps
ensure differential prioritization.
These QoS features allow network administrators to prioritize mission-critical and bandwidth-
intensive traffic, such as enterprise resource planning (ERP), voice (IP telephony traffic), and
computer-aided design and manufacturing (CAD/CAM), over applications such as FTP or e-mail.
For example, it would be undesirable to have a large file download destined to one port on a switch
increase latency in voice traffic destined to another port on this switch. This condition is avoided by
making sure that voice traffic is properly classified and prioritized throughout the network. Other
applications, such as Web browsing, can be handled on a lower-priority basis.
The Cisco Catalyst 2960 Series LAN Base can perform rate limiting through its support of the
Cisco committed information rate (CIR) function. Through CIR, bandwidth can be guaranteed in
increments as small as 1 Mbps. Bandwidth can be allocated based on several criteria, including
MAC source address, MAC destination address, IP source address, IP destination address, and
TCP or UDP port number. Bandwidth allocation is essential when network environments require
service-level agreements or when it is necessary to control the bandwidth given to certain users.
Management
The new Express Setup feature simplifies the initial configuration of a switch. Now you can set up
the switch through a Web browser, eliminating the need for terminal-emulation programs and the
command-line interface (CLI). Express Setup reduces the cost of deployment by helping less-
skilled personnel quickly and easily set up switches.
Cisco Network Assistant is a PC-based network-management application optimized for LANs with
up to 250 users. Cisco Network Assistant offers centralized management of Cisco switches,
routers, and WLAN access points. It supports a wide range of Cisco Catalyst intelligent switches
from Cisco Catalyst 2960 through Cisco Catalyst 4506. Through a user-friendly GUI, users can
configure and manage a wide array of switch functions and start the device manager of Cisco
routers and Cisco wireless access points. A few mouse clicks enable the Cisco recommended
security, availability, and QoS features without the need to consult a detailed design guide. The
Security wizard automatically restricts unauthorized access to servers with sensitive data.
Smartports and wizards save time for network administrators, reduce human errors, and help
ensure that the configuration of the switch is optimized for these applications. Available at no cost,
Cisco Network Assistant can be downloaded from the Cisco Website.
In addition to Cisco Network Assistant, Cisco Catalyst 2960 LAN Base Series Switches provide for
extensive management using SNMP network-management platforms such as the CiscoWorks
LAN Management Solution (LMS). CiscoWorks LMS is a suite of powerful management tools that
simplify the configuration, administration, monitoring, and troubleshooting of Cisco networks. It
integrates these capabilities into a world-class solution for improving the accuracy and efficiency of
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 7 of 21
your operations staff, while increasing the overall availability of your network. CiscoWorks LMS
supports over 400 different device types, providing:
Network discovery, topology views, end-station tracking, and VLAN management
Real-time network fault analysis with easy-to-deploy device-specific best-practice templates
Hardware and software inventory management, centralized configuration tools, and Syslog
monitoring
Network response time and availability monitoring and tracking
Real-time device, link, and port traffic management, analysis, and reporting
Table 2 gives the features and benefits of the Cisco Catalyst 2960 LAN Base Series. Table 3 gives
the hardware specifications, and Table 4 gives the power specifications. Table 5 lists the
management and standards support, and Table 6 provides the safety and compliance information.
Table 2. Features and Benefits of Cisco Catalyst 2960 LAN Base Switches
Feature Benefit
Ease of Use and Deployment
Express Setup simplifies initial configuration with a Web browser, eliminating the need for
more complex terminal emulation programs and CLI knowledge.
IEEE 802.3af and Cisco prestandard PoE support comes with automatic discovery to
detect a Cisco prestandard or IEEE 802.3af endpoint and provide the necessary power
without any user configuration.
Auto Install for configuration and Image update: Simplify management of large number of
switches, by automatically downloading specified configuration and image
DHCP autoconfiguration of multiple switches through a boot server eases switch
deployment.
Automatic QoS (Auto QoS) simplifies QoS configuration in voice-over-IP (VoIP) networks
by issuing interface and global switch commands to detect Cisco IP phones, classify
traffic, and enable egress queue configuration.
Autosensing on each 10/100 port detects the speed of the attached device and
automatically configures the port for 10- or 100-Mbps operation, easing switch deployment
in mixed 10- and 100-Mbps environments.
Autonegotiating on all ports automatically selects half- or full-duplex transmission mode to
optimize bandwidth.
Dynamic Trunking Protocol (DTP) helps enable dynamic trunk configuration across all
switch ports.
Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel
®
groups or Gigabit EtherChannel groups to link to another switch, router, or server.
Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with
devices that conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel
technology and PAgP.
DHCP Server enables a convenient deployment option for the assignment of IP
addresses in networks that do not have without a dedicated DHCP server.
DHCP Relay allows a DHCP relay agent to broadcast DHCP requests to the network
DHCP server.
1000BASE-SX, 1000BASE-LX/LH, 1000BASE-ZX, 1000BASE-BX, 100BASE-FX,
100BASE-LX, 100BASE-BX, and coarse wavelength-division multiplexing (CWDM)
physical interface support through a field-replaceable SFP module provides
unprecedented flexibility in switch deployment.
The default configuration stored in flash memory ensures that the switch can be quickly
connected to the network and can pass traffic with minimal user intervention.
Automatic medium-dependent interface crossover (Auto-MDIX) automatically adjusts
transmit and receive pairs if an incorrect cable type (crossover or straight-through) is
installed on a copper port.
Time-domain reflectometer (TDR) to diagnose and resolve cabling problems on copper
ports.
Configuration Rollback provides the capability to replace the current running configuration
with any saved Cisco IOS
®
Software configuration file. This functionality can be used to
revert to a previous configuration state, effectively rolling back any configuration changes
that were made since that configuration file was saved.
DHCP Auto Install (Boot Host DHCP) and Auto Image Update allows the switch to
automatically download a configuration file and IOS image (future).
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 8 of 21
Manageability
Superior Manageability
Cisco IOS Software CLI support provides a common user interface and command set with all
Cisco routers and Cisco Catalyst desktop switches.
IP Service Level Agreement (responder only) uses active monitoring to generate traffic in a
continuous, reliable, and predictable manner, thus enabling the measurement of network
performance and health.
Switching Database Manager templates for security and QoS allow administrators to easily
adjust memory allocation to the desired features based on deployment-specific requirements.
VLAN trunks can be created from any port using standards-based 802.1q tagging.
Up to 255 VLANs per switch and up to 128 spanning-tree instances per switch are supported.
Four thousand VLAN IDs are supported.
Voice VLAN simplifies telephony installations by keeping voice traffic on a separate VLAN for
easier administration and troubleshooting.
Cisco VTP supports dynamic VLANs and dynamic trunk configuration across all switches.
IGMPv3 snooping for IPv4 and MLD v1 and v2 Snooping for IPv6 provide fast client joins and
leaves of multicast streams and limits bandwidth-intensive video traffic to only the requestors.
Remote SPAN (RSPAN) allows administrators to remotely monitor ports in a Layer 2 switch
network from any other switch in the same network.
For enhanced traffic management, monitoring, and analysis, the Embedded Remote
Monitoring (RMON) software agent supports four RMON groups (history, statistics, alarms,
and events).
Layer 2 trace route eases troubleshooting by identifying the physical path that a packet takes
from source to destination.
All RMON groups are supported through a SPAN port, which permits traffic monitoring of a
single port, or a group of ports, from a single network analyzer or RMON probe.
Domain Name System (DNS) provides IP address resolution with user-defined device names.
Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades by
downloading from a centralized location.
Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all intranet
switches.
Multifunction LEDs per port for port status; half-duplex and full-duplex mode; and 10BASE-T,
100BASE-TX, and 1000BASE-T indication as well as switch-level status LEDs for system,
and redundant power supply provide a comprehensive and convenient visual management
system.
Cisco Discovery Protocol Versions 1 and 2 help enable automatic switch discovery for
network management tools and communicate Voice VLAN information with Cisco IP phones.
Link Layer Discovery Protocol (LLDP) and LLDP Media Extensions (LLDP-MED) including
client location information. Switches exchange link and device information in multivendor
networks.
IPv6 Host provides basic IPv6 management such as IPv4/IPv6 dual stack, unicast address
types, ICMPv6, AAAA DNS lookup over IPv4, Secure Shell (SSH) for v6, IPv6 neighbor
discovery, CDP, Telnet, TFTP, SNMP, HTTP, HTTPS , Traceroute, syslog for v6.
Cisco Network Assistant
Software
Cisco Network Assistant is a no-charge, Windows-based application that simplifies the
administration of networks of up to 250 users. It supports a wide range of Cisco Catalyst
intelligent switches. With Cisco Network Assistant, users can manage Cisco Catalyst switches
and launch the device managers of Cisco integrated services routers and Cisco Aironet
®
WLAN access points.
The easy-to-use graphical interface provides both a topology map and front-panel view of the
cluster and stacks.
Configuration wizards need just a few user inputs to automatically configure the switch to
optimally handle different types of traffic: voice, video, multicast, and high-priority data.
A security wizard is provided to restrict unauthorized access to applications, servers, and
networks.
Upgrading the Cisco IOS Software on Cisco Catalyst switches is a simple matter of pointing
and clicking, with one-click upgrades.
Cisco Network Assistant supports multilayer feature configurations such as routing protocols,
ACLs, and QoS parameters.
Multidevice and multiport configuration capabilities allow administrators to save time by
configuring features across multiple switches and ports simultaneously.
The user-personalized interface allows modification of polling intervals, table views, and other
settings.
Alarm notification provides automated e-mail notification of network errors and alarm
thresholds.
Cisco Express Setup
Express Setup simplifies initial configuration of a switch through a Web browser, eliminating
the need for terminal emulation programs and CLI knowledge.
The Web interface helps less-skilled personnel quickly and simply set up switches, thereby
reducing the cost of deployment.
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 9 of 21
CiscoWorks Support
CiscoWorks network-management software provides management capabilities on a per-port
and per-switch basis, providing a common management interface for Cisco routers, switches,
and hubs.
SNMPv1, v2c, and v3 and Telnet interface support delivers comprehensive in-band
management, and a CLI-based management console provides detailed out-of-band
management.
The CiscoWorks LAN Management Solution supports the Cisco Catalyst 2960 Series.
Availability and Scalability
Superior Redundancy for
Fault Backup
IEEE 802.1x Voice-aware security disables the offending data VLAN when a violation is
detected without affecting Voice VLAN on the same switch port
IEEE 802.1x readiness check determines readiness of connected end hosts, before
configuring 802.1x on the switch.
Cisco UplinkFast and BackboneFast technologies help ensure quick failover recovery,
enhancing overall network stability and reliability.
IEEE 802.1w Rapid Spanning Tree Protocol provides rapid spanning-tree convergence
independent of spanning-tree timers and the benefit of distributed processing.
Per-VLAN Rapid Spanning Tree Plus (PVRST+) allows rapid spanning-tree reconvergence on
a per-VLAN spanning-tree basis, without requiring the implementation of spanning-tree
instances.
Command-switch redundancy enabled in Cisco Network Assistant software allows
designation of a backup command switch that takes over if the primary command switch fails.
Unidirectional Link Detection Protocol (UDLD) and Aggressive UDLD allow unidirectional links
to be detected and disabled to avoid problems such as spanning-tree loops.
Switch port autorecovery (errdisable) automatically attempts to re-enable a link that is
disabled because of a network error.
Cisco Redundant Power System 2300 (RPS 2300) support provides superior internal power-
source redundancy for up to six Cisco networking devices, resulting in improved fault
tolerance and network uptime.
Bandwidth aggregation up to 8 Gbps through Cisco Gigabit EtherChannel technology and up
to 800 Mbps through Cisco Fast EtherChannel technology enhances fault tolerance and offers
higher-speed aggregated bandwidth between switches and to routers and individual servers.
Flex Links provides link redundancy with convergence time 100ms without requiring Spanning
Tree Protocol.
VLAN Flex Links load balancing improves network throughput by utilizing both links for traffic
distribution for different VLANs.
Link State Tracking provides Layer 2 redundancy in the network when used in conjunction
with server or programmable logic controller (PLC) network interface card (NIC) adapter
teaming.
Integrated Cisco IOS
Software Features for
Bandwidth Optimization
Per-port broadcast, multicast, and unicast storm control prevents faulty end stations from
degrading overall systems performance.
IEEE 802.1d Spanning Tree Protocol support for redundant backbone connections and loop-
free networks simplifies network configuration and improves fault tolerance.
PVST+ allows for Layer 2 load sharing on redundant links to efficiently use the extra capacity
inherent in a redundant design.
IEEE 802.1s Multiple Spanning Tree Protocol allows a spanning-tree instance per VLAN,
enabling Layer 2 load sharing on redundant links.
Egress committed rate (ECR) guarantee provides load balancing and redundancy.
Local Proxy Address Resolution Protocol (ARP) works in conjunction with Private VLAN Edge
to minimize broadcasts and maximize available bandwidth.
VLAN1 minimization allows VLAN1 to be disabled on any individual VLAN trunk link.
VLAN Trunking Protocol (VTP) pruning limits bandwidth consumption on VTP trunks by
flooding broadcast traffic only on trunk links required to reach the destination devices.
Internet Group Management Protocol (IGMP) version 3 snooping provides fast client joins and
leaves of multicast streams and limits bandwidth-intensive video traffic to only the requestors.
IGMP filtering provides multicast authentication by filtering out no subscribers and limits the
number of concurrent multicast streams available per port.
Multicast VLAN registration (MVR) continuously sends multicast streams in a multicast VLAN
while isolating e streams from subscriber VLANs for bandwidth and security reasons.
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 10 of 21
QoS and Control
Advanced QoS
Standard 802.1p CoS and DSCP field classification are provided, using marking and
reclassification on a per-packet basis by source and destination IP address, source and
destination MAC address, or Layer 4 TCP or UDP port number.
Cisco control-plane and data-plane QoS ACLs on all ports help ensure proper marking on a
per-packet basis.
Four egress queues per port enable differentiated management of up to four traffic types.
SRR scheduling ensures differential prioritization of packet flows by intelligently servicing the
ingress and egress queues.
Weighted tail drop (WTD) provides congestion avoidance at the ingress and egress queues
before a disruption occurs.
Strict priority queuing guarantees that the highest-priority packets are serviced ahead of all
other traffic.
There is no performance penalty for highly granular QoS functions.
Granular Rate Limiting
The Cisco CIR function guarantees bandwidth in increments as small as 1 Mbps.
Rate limiting is provided based on source and destination IP address, source and destination
MAC address, Layer 4 TCP and UDP information, or any combination of these fields, using
QoS ACLs (IP ACLs or MAC ACLs), class maps, and policy maps.
Asynchronous data flows upstream and downstream from the end station or on the uplink are
easily managed using ingress policing and egress shaping.
Up to 64 aggregate or individual polices are available per Fast Ethernet or Gigabit Ethernet
port.
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 11 of 21
Security
Networkwide Security
Features
IEEE 802.1x allows dynamic, port-based security, providing user authentication.
IEEE 802.1x with VLAN assignment allows a dynamic VLAN assignment for a specific user
regardless of where the user is connected.
IEEE 802.1x with voice VLAN permits an IP phone to access the voice VLAN irrespective of
the authorized or unauthorized state of the port.
IEEE 802.1x and port security are provided to authenticate the port and manage network
access for all MAC addresses, including those of the client.
IEEE 802.1x with Guest VLAN allows guests without 802.1x clients to have limited network
access on the guest VLAN.
Web authentication for non-802.1x clients allows non-802.1x clients to use an SSL-based
browser for authentication.
MAC Auth Bypass (MAB) for voice allows third-party IP phones without an 802.1x supplicant
to get authenticated using their MAC address.
Port-based ACLs for Layer 2 interfaces allow application of security policies on individual
switch ports.
Unicast MAC filtering prevents the forwarding of any type of packet with a matching MAC
address.
Unknown unicast and multicast port blocking allows tight control by filtering packets that the
switch has not already learned how to forward.
SSHv2 and SNMPv3 provide network security by encrypting administrator traffic during Telnet
and SNMP sessions. SSHv2 and the cryptographic version of SNMPv3 require a special
cryptographic software image because of U.S. export restrictions.
Bidirectional data support on the Switched Port Analyzer (SPAN) port allows the Cisco Secure
intrusion detection system (IDS) to take action when an intruder is detected.
TACACS+ and RADIUS authentication enable centralized control of the switch and restrict
unauthorized users from altering the configuration.
MAC address notification allows administrators to be notified of users added to or removed
from the network.
DHCP snooping allows administrators to ensure consistent mapping of IP to MAC addresses.
This can be used to prevent attacks that attempt to poison the DHCP binding database, and
to rate-limit the amount of DHCP traffic that enters a switch port.
DHCP Interface Tracker (Option 82) feature augments a host IP address request with the
switch port ID.
Port security secures the access to an access or trunk port based on MAC address.
After a specific timeframe, the aging feature removes the MAC address from the switch to
allow another device to connect to the same port.
Trusted Boundary provides the ability to trust the QoS priority settings if an IP phone is
present and to disable the trust setting if the IP phone is removed, thereby preventing a
malicious user from overriding prioritization policies in the network.
Multilevel security on console access prevents unauthorized users from altering the switch
configuration.
The user-selectable address-learning mode simplifies configuration and enhances security.
BPDU Guard shuts down Spanning Tree Protocol PortFast-enabled interfaces when BPDUs
are received to avoid accidental topology loops.
Spanning-Tree Root Guard (STRG) prevents edge devices not in the network administrator’s
control from becoming Spanning Tree Protocol root nodes.
Voice VLAN aware port security and BPDU Guard allow Voice VLAN traffic to not be
disrupted when security violations occur.
IGMP filtering provides multicast authentication by filtering out no subscribers and limits the
number of concurrent multicast streams available per port.
Dynamic VLAN assignment is supported through implementation of VLAN Membership Policy
Server (VMPS) client functions to provide flexibility in assigning ports to VLANs. Dynamic
VLAN helps enable the fast assignment of IP addresses.
Cisco Network Assistant software security wizards ease the deployment of security features
for restricting user access to a server as well as to a portion of or the entire network.
Up to 512 (Aces) are supported, with two profiles: Security (384 Security ACL entries and 128
QoS policies), and QoS (128 Security ACL entries and 384 QoS policies).
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 12 of 21
Table 3. Cisco Catalyst 2960 LAN Base Switch Hardware
Description Specification
Performance
16 Gbps switching fabric (Catalyst 2960PD-8TT-L , Catalyst 2960-8TC-L, Catalyst 2960-
24TT-L, Catalyst 2960-24TC-L, Catalyst 2960-24LT-L, Catalyst 2960-24PC-L, Catalyst
2960-48PST-L, Catalyst 2960-48TT-L, Catalyst 2960-48TC-L)
32 Gbps switching fabric (Catalyst 2960G-8TC-L, Catalyst 2960G-24TC-L, Catalyst
2960G-48TC-L)
Forwarding rate based on 64-byte packets:
Catalyst 2960PD-8TT-L: 2.7 Mpps
Catalyst 2960-8TC-L: 2.7 Mpps
Catalyst 2960-24TT-L: 6.5 Mpps
Catalyst 2960-24TC-L: 6.5 Mpps
Catalyst 2960-24LT-L: 6.5 Mpps
Catalyst 2960-24PC-L : 6.5 Mpps
Catalyst 2960-48TT-L: 10.1 Mpps
Catalyst 2960-48TC-L: 10.1 Mpps
Catalyst 2960-48PST-L : 13.3 Mpps
Catalyst 2960G-8TC-L: 11.9 Mpps
Catalyst 2960G-24TC-L: 35.7 Mpps
Catalyst 2960G-48TC-L: 39.0 Mpps
64 MB DRAM
32 MB flash memory
Configurable up to 8000 MAC addresses
Configurable up to 255 IGMP groups
Configurable maximum transmission unit (MTU) of up to 9000 bytes, with a maximum
Ethernet frame size of 9018 bytes (Jumbo frames) for bridging on Gigabit Ethernet ports,
and up to 1998 bytes for bridging of Multiprotocol Label Switching (MPLS) tagged frames
on both 10/100 and 10/100/1000 ports
Connectors
and Cabling
10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 unshielded twisted-pair
(UTP) cabling
100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling
1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
1000BASE-T SFP-based ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
1000BASE-SX, -LX/LH, -ZX, -BX and CWDM SFP-based ports: LC fiber connectors
(single/multimode fiber)
100BASE-LX, -BX, -FX: LC fiber connectors (single/multimode fiber).
Power Connectors
Customers can provide power to a switch by using either the internal power supply or the
Cisco RPS 675. The connectors are located at the back of the switch.
Note: The Catalyst 2960-8TC-L and Catalyst 2960G-8TC-L do not have RPS ports.
Internal-Power-Supply Connector
The internal power supply is an autoranging unit.
The internal power supply supports input voltages between 100 and 240VAC.
Use the supplied AC power cord to connect the AC power connector to an AC power
outlet.
Cisco RPS Connector
The connector offers connection for an optional Cisco RPS 2300 that uses AC input and
supplies DC output to the switch.
The connector offers a 2300W redundant power system that supports up to six external
network devices and provides power to two failed devices at a time.
The connector automatically senses when the internal power supply of a connected
device fails and provides power to the failed device, preventing loss of network traffic.
Only the Cisco RPS 2300 (model PWR-RPS2300) should be attached to the redundant-
power-system receptacle.
Indicators
Per-port status: Link integrity, disabled, activity, speed, full-duplex
System status: System, RPS, link status, link duplex, link speed
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 13 of 21
Dimensions (H x W x D)
Cisco Catalyst 2960PD-8TT-L : 1.73 x 10.6 x 6.2 in. (4.4 x 27 x 15.7 cm)
Cisco Catalyst 2960-8TC-L: 1.73 x 10.6 x 6.4 in. (4.4 x 27 x 16.3 cm)
Cisco Catalyst 2960-24TT-L: 1.73 x 17.5 x 9.3 in. (4.4 x 44.5 x 23.6 cm)
Cisco Catalyst 2960-48TT-L: 1.73 x 17.5 x 9.3 in. (4.4 x 44.5 x 23.6 cm)
Cisco Catalyst 2960-24TC-L: 1.73 x 17.5 x 9.3 in. (4.4 x 44.5 x 23.6 cm)
Cisco Catalyst 2960-24LT-L: 1.73 x 17.5 x 13 in. (4.4 x 44.5 x 33.2 cm)
Cisco Catalyst 2960-24PC-L : 1.73 x 17.5 x 13 in. (4.4 x 44.5 x 33.2 cm)
Cisco Catalyst 2960-48PST-L : 1.73 x 17.5 x 13 in. (4.4 x 44.5 x 33.2 cm)
Cisco Catalyst 2960-48TC-L: 1.73 x 17.5 x 9.3 in. (4.4 x 44.5 x 23.6 cm)
Cisco Catalyst 2960G-8TC-L: 1.73 x 10.6 x 8.1 in. (4.4 x 27 x 20.5 cm)
Cisco Catalyst 2960G-24TC-L: 1.73 x 17.5 x 12.9 in. (4.4 x 44.5 x 32.8 cm)
Cisco Catalyst 2960G-48TC-L: 1.73 x 17.5 x 12.9 in. (4.4 x 44.5 x 32.8 cm)
Weight
Cisco Catalyst 2960PD-8TT-L: 3 lb (1.4 kg)
Cisco Catalyst 2960-8TC-L: 3 lb (1.4 kg)
Cisco Catalyst 2960-24TT-L: 8 lb (3.6 kg)
Cisco Catalyst 2960-48TT-L: 8 lb (3.6 kg)
Cisco Catalyst 2960-24TC-L: 8 lb (3.6 kg)
Cisco Catalyst 2960-24LT-L : 10 lb (4.5 kg)
Cisco Catalyst 2960-24PC-L : 12 lb (5.4 kg)
Cisco Catalyst 2960-48PST-L : 12 lb (5.4 kg)
Cisco Catalyst 2960-48TC-L: 8 lb (3.6 kg)
Cisco Catalyst 2960G-8TC-L: 3 lb (1.4 kg)
Cisco Catalyst 2960G-24TC-L: 10 lb (4.5 kg)
Cisco Catalyst 2960G-48TC-L: 12 lb (5.4 kg)
Environmental Ranges Normal Operating Conditions:
-5ºC to +45ºC, up to 5,000 feet (1500 m)
-5ºC to +40ºC, up to 10,000 feet (3000 m)
-5ºC to +35ºC, up to 13,000 feet (4000 m)
Short-Term* Exceptional Operating Conditions:
-5ºC to +55ºC, at sea level
-5ºC to +50ºC, up to 5,000 feet (1500 m)
-5ºC to +45ºC, up to 10,000 feet (3000 m)
-5'C to +40'C, up to 13,000 feet (4000 m)
* Not more than following in one year period: 96 consecutive hours, or 360 hours total, or 15
occurrences
* For Catalyst 2960G-8TC-L, reduce the high range temperature byC
Acoustic Noise
ISO 7779: Bystander position operating to an ambient temperature of 25°C
Cisco Catalyst 2960PD-8TT-L: 0 dBa (no fan)
Cisco Catalyst 2960-8TC-L: 0 dBa (no fan)
Cisco Catalyst 2960-24TT-L: 40 dBa
Cisco Catalyst 2960-48TT-L: 40 dBa
Cisco Catalyst 2960-24TC-L: 40 dBa
Cisco Catalyst 2960-24LT-L : 48 dBa
Cisco Catalyst 2960-24PC-L : 48 dBa
Cisco Catalyst 2960-48PST-L : 48 dBa
Cisco Catalyst 2960-48TC-L: 40 dBa
Cisco Catalyst 2960G-8TC-L: 0 dBa (no fan)
Cisco Catalyst 2960G-24TC-L: 41 dBa
Cisco Catalyst 2960G-48TC-L: 43 dBa
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 14 of 21
Mean Time Between Failure
(MTBF)
Cisco Catalyst 2960PD-8TT-L: 737,065 hrs
Cisco Catalyst 2960-8TC-L: 615,549 hrs
Cisco Catalyst 2960-24TT-L: 407,707 hrs
Cisco Catalyst 2960-48TT-L: 339,743 hrs
Cisco Catalyst 2960-24TC-L: 402,926 hrs
Cisco Catalyst 2960-24LT-L : 311,781 hrs
Cisco Catalyst 2960-24PC-L : 243,277 hrs
Cisco Catalyst 2960-48TC-L: 336,409 hrs
Cisco Catalyst 2960-48PC-L: 180,427 hrs
Cisco Catalyst 2960G-8TC-L: 485,576 hrs
Cisco Catalyst 2960G-24TC-L: 313,828 hrs
Cisco Catalyst 2960G-48TC-L: 221,432 hrs
AC Input Voltage
and Current
DC input, 48 VDC, 0.3A (Cisco Catalyst 2960PD-8TT-L),
(For AC input, use PWR-A= sold separately)
100-240VAC (autoranging), 0.5-0.25A, 50-60 Hz (Cisco Catalyst 2960-8TC-L)
100-240VAC (autoranging), 0.8-0.4A, 50-60 Hz (Cisco Catalyst 2960G-8TC-L)
100-240 VAC (autoranging), 3.0-1.5A, 50-60 Hz (Cisco Catalyst 2960-24LT-L)
100-240 VAC (autoranging) 8.0-4.0A, 50-60 Hz (Cisco Catalyst 2960-24PC-L)
100-240 VAC (autoranging) 5.0-2.0A, 50-60 Hz (Cisco Catalyst 2960-48PST-L)
100-240VAC (autoranging), 1.3–0.8A, 50–60 Hz (Cisco Catalyst 2960-24TT-L and
Catalyst 2960-24TC-L and Catalyst 2960-48TT-L and Catalyst 2960-48TC-L)
100-240VAC (autoranging), 3.0–1.5A, 50–60 Hz (Cisco Catalyst 2960G-24TC-L and
Catalyst 2960G-48TC-L)
Power Rating
Cisco Catalyst 2960PD-8TT-L : 11 W
Cisco Catalyst 2960-8TC-L: 0.035 kVA
Cisco Catalyst 2960-24TT-L: 0.05kVA
Cisco Catalyst 2960-48TT-L: 0.075kVA
Cisco Catalyst 2960-24TC-L: 0.05kVA
Cisco Catalyst 2960-24LT-L : 0.175 kVA
Cisco Catalyst 2960-24PC-L : 0.470 kVA
Cisco Catalyst 2960-48PST-L : 0.5 kVA
Cisco Catalyst 2960-48TC-L: 0.075kVA
Cisco Catalyst 2960G-8TC-L: 0.05 kVA
Cisco Catalyst 2960G-24TC-L: 0.075kVA
Cisco Catalyst 2960G-48TC-L: 0.140kVA
DC Input Voltages
(RPS Input)
(No RPS input for Cisco Catalyst 2960PD-8TT-L , Catalyst 2960-8TC-L and Catalyst
2960G-8TC-L)
Cisco Catalyst 2960-24TT-L: +12V at 5A
Cisco Catalyst 2960-48TT-L: +12V at 5A
Cisco Catalyst 2960-24TC-L: +12V at 5A
Cisco Catalyst 2960-24LT-L : +12V at 8.3A, -48V at 2.7A
Cisco Catalyst 2960-24PC-L : +12V at 11.25A, -48V at 7.8A
Cisco Catalyst 2960-48PST-L : +12V at 4A, -48V at 7.8A
Cisco Catalyst 2960-48TC-L: +12V at 5A
Cisco Catalyst 2960G-24TC-L: +12V at 10.5A
Cisco Catalyst 2960G-48TC-L: +12V at 10.5A
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 15 of 21
Table 4. Power Specifications for Cisco Catalyst 2960 LAN Base Switches
Power Consumption
Description WS-C2960-
24T-L
WS-C2960-
8TC-L
WS-C2960-
24TC-L
WS-C2960-
48TC-L
WS-2960PD-
8TT-L
WS-C2960-
24TT-L
WS-C2960-
48TT-L
5% Throughput
Measured Power
Consumption
21W 11W 24W 36W N/A 26W 38W
Measured Output
BTU
71 37 82 122 N/A 86 130
100% Throughput
Measured Power
Consumption
22W 12W 27W 39W 11W 28W 42W
Measured Output
BTU
75 39 90 133 38 93 141
5% Throughput (with 50% PoE loads)
Measured Power
Consumption
N/A N/A N/A N/A N/A N/A N/A
Measured Output
BTU
N/A N/A N/A N/A N/A N/A N/A
100% Throughput (with maximum possible PoE loads)
Measured Power
Consumption
N/A N/A N/A N/A N/A N/A N/A
Measured Output
BTU
N/A N/A N/A N/A N/A N/A N/A
Table 5. Power Specifications for Cisco Catalyst 2960 LAN Base Switches
Power Consumption
Description WS-C2960-
24PC-L
WS-C2960-
24LT-L
WS-C2960-
48PST-L
WS-C2960G-
8TC-L
WS-C2960G-
24TC-L
WS-C2960G-
48TC-L
5% Throughput
Measured Power
Consumption
43W 34W 63W 20W 65W 114W
Measured Output
BTU
144 114 214 68 219 388
100% Throughput
Measured Power
Consumption
45W 36W 67W 22W 72W 123W
Measured Output
BTU
151 121 227 75 244 419
5% Throughput (with 50% PoE loads)
Measured Power
Consumption
Switch Power:
237W
Switch Power:
98W
Switch Power:
262W
N/A N/A N/A
PoE Power:
185W
PoE Power:
62W
PoE Power:
187W
Measured Output
BTU
Switch output::
175
Switch output::
122
Switch output::
253
N/A N/A N/A
100% Throughput (with maximum possible PoE loads)
Measured Power
Consumption
Switch Power:
433W
Switch Power:
162W
Switch Power:
460W
N/A N/A N/A
Measured Output
BTU
PoE Power:
357W
PoE Power:
119W
PoE Power:
339W
N/A N/A N/A
Switch output::
171
Switch output::
66
Switch output::
208
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 16 of 21
Note: All power consumption numbers were measured under controlled laboratory conditions
and are provided as an estimate.
The wattage rating on the power supply does not represent actual power draw. It indicates the
maximum power draw possible by the power supply. This rating can be used for facility capacity
planning. For PoE switches, cooling requirements are smaller than the actual power consumption
as a significant portion of PoE loads are dissipated in the end points
Non PoE Power Consumption
100% Throughput Switch Power consumption
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 Degrees Celsius, atmospheric pressure in the range of 860
to 1060 mbar and relative Humidity between 30 to 75%. Typically such power draws are only seen
when encountering a 100% traffic load made up entirely of 64 byte packets on the switch and the
uplinks.
5% Throughput Switch Power consumption
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 Degrees Celsius, atmospheric pressure in the range of 860
to 1060 mbar and relative Humidity between 30 to 75%. The numbers below indicate a 5% traffic
load on the switch and its uplinks.
PoE Power Consumption
100% Throughput Switch Power consumption (no PoE loads)
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 Degrees Celsius, atmospheric pressure in the range of 860
to 1060 mbar and relative Humidity between 30 to 75%. Typically such power draws are only seen
when encountering a 100% traffic load made up entirely of 64 byte packets with no PoE loads on
the switch and uplinks.
Measured 5% Throughput Switch Power consumption (no PoE loads)
The numbers indicate the power consumed by a typical switch under normal conditions. Normal
conditions signify a temperature of 25 Degrees Celsius, atmospheric pressure in the range of 860
to 1060 mbar and relative Humidity between 30 to 75%. The numbers below indicate a 5% traffic
load on the switch and its uplinks
100% Throughput Switch Power consumption (with maximum PoE loads)
The numbers indicate the power consumed by a typical system (the switch and the corresponding
PoE loads) under normal conditions. Normal conditions signify a temperature of 25 Degrees
Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative Humidity between 30
to 75%. Typically this power draw is realized when a switch is running 100% traffic load of 64 byte
sized packets on all its ports and uplinks and also drawing 100% PoE load .
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 17 of 21
5% Throughput Switch Power consumption (with 50% PoE loads).
The numbers indicate the power consumed by a typical system (the switch and the corresponding
PoE loads) under normal conditions. Normal conditions signify a temperature of 25 Degrees
Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative Humidity between 30
to 75%. The numbers below indicate a 5% traffic load and 50% PoE load on the switch and its
uplinks.
Table 6. Management and Standards Support for Cisco Catalyst 2960 LAN Base Switches
Description Specification
Management
BRIDGE-MIB
CISCO-CABLE-DIAG-MIB
CISCO-CDP-MIB
CISCO-CLUSTER-MIB
CISCO-CONFIG-COPY-MIB
CISCO-CONFIG-MAN-MIB
CISCO-DHCP-SNOOPING-MIB
CISCO-ENTITY-VENDORTYPE-OID-MIB
CISCO-ENVMON-MIB
CISCO-ERR-DISABLE-MIB
CISCO-FLASH-MIB
CISCO-FTP-CLIENT-MIB
CISCO-IGMP-FILTER-MIB
CISCO-IMAGE-MIB
CISCO-IP-STAT-MIB
CISCO-LAG-MIB
CISCO-MAC-NOTIFICATION-MIB
CISCO-MEMORY-POOL-MIB
CISCO-PAGP-MIB
CISCO-PING-MIB
CISCO-POE-EXTENSIONS-MIB
CISCO-PORT-QOS-MIB
CISCO-PORT-SECURITY-MIB
CISCO-PORT-STORM-CONTROL-MIB
CISCO-PRODUCTS-MIB
CISCO-PROCESS-MIB
CISCO-RTTMON-MIB
CISCO-SMI-MIB
CISCO-STP-EXTENSIONS-MIB
CISCO-SYSLOG-MIB
CISCO-TC-MIB
CICSO-TCP-MIB
CISCO-UDLDP-MIB
CISCO-VLAN-IFTABLE-
RELATIONSHIP-MIB
CISCO-VLAN-MEMBERSHIP-MIB
CISCO-VTP-MIB
ENTITY-MIB
ETHERLIKE-MIB
IEEE8021-PAE-MIB
IEEE8023-LAG-MIB
IF-MIB
INET-ADDRESS-MIB
OLD-CISCO-CHASSIS-MIB
OLD-CISCO-FLASH-MIB
OLD-CISCO-INTERFACES-MIB
OLD-CISCO-IP-MIB
OLD-CISCO-SYS-MIB
OLD-CISCO-TCP-MIB
OLD-CISCO-TS-MIB
RFC1213-MIB
RMON-MIB
RMON2-MIB
SNMP-FRAMEWORK-MIB
SNMP-MPD-MIB
SNMP-NOTIFICATION-MIB
SNMP-TARGET-MIB
SNMPv2-MIB
TCP-MIB
UDP-MIB
Standards
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1p CoS Prioritization
IEEE 802.1Q VLAN
IEEE 802.1s
IEEE 802.1w
IEEE 802.1x
IEEE 802.1AB (LLDP)
IEEE 802.3ad
IEEE 802.3af
IEEE 802.3ah (100BASE-X single/multimode
fiber only)
IEEE 802.3x full duplex on 10BASE-T,
100BASE-TX, and 1000BASE-T ports
IEEE 802.3 10BASE-T specification
IEEE 802.3u 100BASE-TX specification
IEEE 802.3ab 1000BASE-T specification
IEEE 802.3z 1000BASE-X specification
100BASE-BX (SFP)
100BASE-FX (SFP)
100BASE-LX (SFP)
1000BASE-BX (SFP)
1000BASE-SX (SFP)
1000BASE-LX/LH (SFP)
1000BASE-ZX (SFP)
1000BASE-CWDM SFP 1470 nm
1000BASE-CWDM SFP 1490 nm
1000BASE-CWDM SFP 1510 nm
1000BASE-CWDM SFP 1530 nm
1000BASE-CWDM SFP 1550 nm
1000BASE-CWDM SFP 1570 nm
1000BASE-CWDM SFP 1590 nm
1000BASE-CWDM SFP 1610 nm
RMON I and II standards
SNMPv1, SNMPv2c, and SNMPv3
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 18 of 21
Table 7. Safety and Compliance
Description Specification
Safety Certifications
UL 60950-1, First Edition
CUL to CAN/CSA 22.2 No. 60950-1, First Edition
TUV/GS to EN 60950-1, First Edition
CB to IEC 60950-1 with all country deviations
AS/NZS 60950-1, First Edition
CE Marking
NOM (through partners and distributors)
Electromagnetic
Compatibility Certifications
FCC Part 15 Class A
EN 55022 Class A (CISPR22)
EN 55024 (CISPR24)
AS/NZS CISPR22 Class A
CE
CNS13438 Class A
MIC
GOST
China EMC Certifications
Environmental Reduction of Hazardous Substances (ROHS) 5
Telco Common Language Equipment Identifier (CLEI) code
Warranty Limited lifetime warranty
Service and Support
Cisco is committed to minimizing total cost of ownership. Our portfolio of technical support
services helps ensure that Cisco products operate efficiently, remain highly available, and benefit
from the most up-to-date system software. The services and support programs described in Table
7 are available as part of the Cisco Desktop Switching Service and Support solution and are
available directly from Cisco and through resellers.
Table 8. Cisco Services and Support Programs
Service and Support Features Benefits
Cisco Total Implementation
Solutions (TIS), available direct from
Cisco
Cisco Packaged TIS, available
through resellers
Cisco SMARTnet
®
and SMARTnet
Onsite support, available direct from
Cisco
Cisco Packaged SMARTnet support
program, available through resellers
Cisco SMB Support Assistant
Project management
Site survey, configuration, and
deployment
Installation, text, and cutover
Training
Major moves, adds, and changes
Design review and product staging
24-hour access to software updates
Web access to technical repositories
Telephone support through the Cisco
Technical Assistance Center
Advance replacement of hardware
parts
Supplements existing staff
Helps ensure that functions meet
needs
Mitigates risk
Helps enable proactive or expedited
issue resolution
Lowers total cost of ownership by
taking advantage of Cisco expertise
and knowledge
Helps minimize network downtime
Ordering Information
Table 8 gives ordering information for Cisco Catalyst 2960 LAN Base Switches.
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 19 of 21
Table 9. Ordering Information for Cisco Catalyst 2960 LAN Base Switches
Part Numbers Description
WS-C2960PD-8TT-L
8 Ethernet 10/100 ports and 1 10/100/1000 PoE input port
Power adaptor (PWR-A=) and power cord sold separately
Compact size with no fan; magnet included
LAN Base Image installed
WS-C2960-8TC-L
8 Ethernet 10/100 ports and 1 dual-purpose uplink (dual-purpose uplink port has one
10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
Compact size with no fan; magnet included
LAN Base Image installed
WS-C2960-24TT-L
24 Ethernet 10/100 ports and two 10/100/1000TX uplinks
1 RU fixed-configuration
LAN Base Image installed
WS-C2960-48TT-L
48 Ethernet 10/100 ports and two 10/100/1000TX uplinks
1 RU fixed-configuration
LAN Base Image installed
WS-C2960-24LT-L
24 Ethernet 10/100 ports with 8 PoE ports and two 10/100/1000TX uplinks
1 RU fixed-configuration
LAN Base Image installed
WS-C2960-24PC-L
24 Ethernet 10/100 PoE ports and 2 dual-purpose uplinks
1 RU fixed-configuration
LAN Base Image installed
WS-C2960-48PST-L
48 Ethernet 10/100 PoE ports and 2 10/100/1000 uplinks and 2 SFP uplinks
1 RU fixed-configuration
LAN Base Image installed
WS-C2960-48TC-L
48 Ethernet 10/100 ports and 2 dual-purpose uplinks (each dual-purpose uplink port has
one 10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
1 RU fixed-configuration
LAN Base Image installed
WS-C2960G-8TC-L
7 Ethernet 10/100/1000 ports and 1 dual-purpose uplink (dual-purpose uplink port has
one 10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
Compact size with no fan; magnet included
LAN Base Image installed
WS-C2960G-24TC-L
20 Ethernet 10/100/1000 ports and 4 dual-purpose uplinks (each dual-purpose uplink port
has one 10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
1 RU fixed-configuration
LAN Base Image installed
WS-C2960G-48TC-L
44 Ethernet 10/100/1000 ports and 4 dual-purpose uplinks (each dual-purpose uplink port
has one 10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
1 RU fixed-configuration
LAN Base Image installed
PWR-RPS2300 Cisco Redundant Power System 2300 and Blower,No Power Supply
BLNK-RPS2300= Spare Bay Insert for Cisco Redundant Power System 2300
CAB-RPS2300-E= Spare RPS2300 Cable for Cisco Catalyst 2960-24PC-L and 2960-24LT-L switches
CAB-RPS2300= Spare RPS2300 Cable for Cisco Catalyst 2960 switches except Catalyst 2960-24PC-L and
2960-24LT-L switches
BLWR-RPS2300= Spare 45CFM Blower for Cisco Redundant Power System 2300
C3K-PWR-750WAC= Catalyst 3750-E/3560-E/RPS 2300 750WAC power supply spare
PWR-A= Power adaptor for Cisco Catalyst 2960PD-8TT-L compact switch
CBLGRD-C2960-8TC= Cable guard for the Cisco Catalyst 2960-8TC compact switch
CBLGRD-C2960G-8TC= Cable guard for the Cisco Catalyst 2960G-8TC compact switch
RCKMNT-19-CMPCT= Rack-mount for the Cisco Catalyst 2960-8TC and Catalyst 2960G-8TC compact switches
RCKMNT-1RU= Spare rack-mount kit for the Cisco Catalyst 2960 Series
RCKMNT-REC-1RU= 1 RU recessed rack-mount kit for the Cisco Catalyst 2960 Series
Data Sheet
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information. Page 20 of 21
GLC-LH-SM= 1000BASE-LX/LH SFP transceiver module for MMF and SMF, 1300-nm wavelength
GLC-SX-MM= 1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength
GLC-ZX-SM= 1000BASE-ZX SFP transceiver module for SMF, 1550-nm wavelength
GLC-T= 1000BASE-T SFP transceiver module for Category 5 copper wire
Not supported on the Cisco Catalyst 2960-8TC and Catalyst 2960G-8TC
compact switches
GLC-BX-D= 1000BASE-BX10 SFP transceiver module for single strand SMF, 1490-nm TX / 1310-nm RX
wavelength
GLC-BX-U= 1000BASE-BX10 SFP transceiver module for single strand SMF, 1310-nm TX / 1490-nm RX
wavelength
GLC-GE-100FX= 100BASE-FX SFP module for Gigabit Ethernet ports, 1310-nm wavelength, 2 km over MMF
Not supported on the Cisco Catalyst 2960-8TC and Catalyst 2960G-8TC compact switches
GLC-FE-100FX= 100BASE-FX SFP module for 100-Mb ports, 1310-nm wavelength, 2 km over MMF
GLC-FE-100LX= 100BASE-LX10 SFP module for 100-Mb ports, 1310-nm wavelength, 10 km over SMF
GLC-FE-100BX-D= 100BASE-BX10-D SFP module for 100-Mb ports, 1550-nm TX /1310-nm RX wavelength,
10 km over single-strand SMF
GLC-FE-100BX-U= 100BASE-BX10-U SFP module for 100-Mb ports, 1310-nm TX/1550-nm RX wavelength,
10 km over single-strand SMF
CWDM-SFP-1470= Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G FC (gray)
CWDM-SFP-1490= Cisco CWDM SFP, 1490 nm; Gigabit Ethernet and 1G/2G FC (violet)
CWDM-SFP-1510= Cisco CWDM SFP, 1510 nm; Gigabit Ethernet and 1G/2G FC (blue)
CWDM-SFP-1530= Cisco CWDM SFP, 1530 nm; Gigabit Ethernet and 1G/2G FC (green)
CWDM-SFP-1550= Cisco CWDM SFP, 1550 nm; Gigabit Ethernet and 1G/2G FC (yellow)
CWDM-SFP-1570= Cisco CWDM SFP, 1570 nm; Gigabit Ethernet and 1G/2G FC (orange)
CWDM-SFP-1590= Cisco CWDM SFP, 1590 nm; Gigabit Ethernet and 1G/2G FC (red)
CWDM-SFP-1610= Cisco CWDM SFP, 1610 nm; Gigabit Ethernet and 1G/2G FC (brown)
CAB-SM-LCSC-1M 1m fiber single-mode LC-to-SC connectors
CAB-SM-LCSC-5M 5m fiber single-mode LC-to-SC connectors
For more information about Cisco products, contact:
United States and Canada (toll free): (800) 553-6387
Europe: 32 2 778 4242
Australia: 612 9935 4107
Other: (408) 526-7209
URL:
http://www.cisco.com
1 / 1

Cisco WS-C2960G-24TC-LOB Datasheet

Category
Network switches
Type
Datasheet
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Ask the document