American Dynamics Intellex Intellex Ultra Installation And Configuration Manual

Intellex® Ultra

Version 4.0

Part Number 8200-0563-00 A0

Installation and Configuration

Guide

ii

Notice

The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products.

All specifications are therefore subject to change without notice.

Copyright

Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any

electronic medium or machine-readable form, in whole or in part, without prior written consent of Sensormatic Electronics. ©

American Dynamics

6795 Flanders Drive

San Diego, CA 92121-2903 U.S.A.

Customer Service

Thank you for using American Dynamics products. We support our products through an extensive worldwide network of dealers. The

dealer through whom you originally purchased this product is your point of contact if you need service or support. Our dealers are

empowered to provide the very best in customer service and support. Dealers should contact American Dynamics at (800) 507-6268

or (561) 912-6259 or on the Web at www.americandynamics.net.

Trademarks

Intellex

®

is a registered trademark of Sensormatic Electronics Corporation. IntelleCord

™

and Smart Search

™

are trademarks of

Sensormatic Electronics Corporation. Windows

®

is a registered trademark of Microsoft Corporation. PS/2

®

is a registered trademark

of International Business Machines Corporation. Sony

®

is a registered trademark of Sony Corporation.

Trademarked names are used throughout this manual. Rather than place a symbol at each occurrence, trademarked names are

designated with initial capitalization. Inclusion or exclusion is not a judgment on the validity or legal status of the term.

iii

Warnings

WARNING: TO REDUCE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

DO NOT INSTALL THIS PRODUCT IN HAZARDOUS AREAS WHERE HIGHLY

COMBUSTIBLE OR EXPLOSIVE PRODUCTS ARE STORED OR USED.

The lightning flash/arrowhead symbol, within an equilateral triangle, alerts the user to the presence of a shock hazard within the

product’s enclosure.

CAUTION: Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the battery manufacturer. Dispose of used batteries according to the

battery manufacturer’s instructions.

VORSICHT: ZUR VERMEIDUNG EINES STROMSCHLAGES DARF DAS GEHÄUSE NICHT ENTFERNT WERDEN. ES ENTHÄLT

KEINE VOM BENUTZER ZU WARTENDEN TEILE. ÜBERLASSEN SIE DIE WARTUNG NUR QUALIFIZIERTEM

FACHPERSONAL.

CAUTION: Es besteht die Gefahr einer Explosion, wenn die Batterie nicht ordnungsgemäß

ausgetauscht wird.

WARNING: THIS EQUIPMENT IS A CLASS 1 LASER PRODUCT INCORPORATING A CLASS 1

LASER DIODE AND IT COMPLIES WITH FDA RADIATION PERFORMANCE

STANDARDS, 21 CFR SUBCHAPTER J AND THE CANADIAN RADIATION EMITTING

DEVICES ACT, REDR C1370.

Rack Mounting

Consult with the supplier of your equipment rack for adequate rack mounting means, with proper consideration for the weight of this

product.

Consult with the manufacturer of your rack regarding the proper hardware and procedure of mounting this product in a safe and

useable fashion

Avoid uneven loading or mechanical instability when rack-mounting units.

Make sure that units are installed to get enough air flow for safe operation.

The maximum temperature for rack-mounted units is 40° C.

Avoid uneven loading or mechanical instability when rack-mounting units.

Check product label for power supply requirements to assure that no overloading of supply circuits or overcurrent protection occurs.

Mains grounding must be reliable and uncompromised by any connections.

WARNING: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR

A CLASS “A” DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE

LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST

HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL

ENVIRONMENT. THIS EQUIPMENT GENERATES, USES AND CAN RADIATE RADIO

FREQUENCY ENERGY AND, IF NOT INSTALLED AND USED IN ACCORDANCE WITH

THE INSTRUCTION MANUAL, MAY CAUSE INTERFERENCE TO RADIO

COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS

LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE

REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate

the equipment.

NOTE: This product was FCC verified under test conditions that included the use of shielded I/O cables

and connectors between system components. To be in compliance with FCC regulations, the user

must use shielded cables and connectors for all except power and alarm cables.

This digital apparatus does not exceed the Class A limits for radio noise emissions as set out in the Radio Interference Regulations

(ICES-003) of the Canadian Department of Communications.

iv

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables de la Classe A prescrites dans

le Réglement (ICES-003) sur le brouillage radioélectrique édicté par le Ministère des Communications du Canada.

v

License Information

READ THIS LICENSE AGREEMENT BEFORE OPENING THE DISK PACKAGE, INSTALLING THE SOFTWARE, OR USING YOUR

SYSTEM.

THIS LICENSE AGREEMENT DEFINES YOUR RIGHTS AND OBLIGATIONS. BY BREAKING THE SEAL ON THIS PACKAGE,

INSTALLING THE SOFTWARE, OR USING YOUR SYSTEM, YOU AGREE TO ALL OF THE TERMS AND CONDITIONS OF THIS

AGREEMENT. IF YOU DO NOT AGREE TO ALL OF THE TERMS AND CONDITIONS OF THIS AGREEMENT, YOU MAY, WITHIN

30 DAYS, RETURN THIS PACKAGE, ALL THE DOCUMENTATION, AND ALL ACCOMPANYING MATERIAL(S) TO THE POINT OF

PURCHASE FOR A REFUND.

SOFTWARE LICENSE

The software includes the Intellex API, modular programs and source codes provided as samples, the Intellex API manual and any

electronic documentation; and is provided to you by installing the software on a computer hard drive. The software is licensed, not

sold.

GRANT OF LICENSE

The purchase of Intellex API software constitutes a license agreement between Sensormatic and you. This license agreement

permits you and only you to use the software. By purchasing the Intellex API license agreement, you may use the API software and

accompanying modular programs with their source codes. This license agreement does not grant you the right to resell nor distribute

the API nor the modular programs and their source codes or additional copies of them to another entity. The software is only licensed

for use with Intellex equipment. There are no restrictions on instituting a licensing program internal to your organization with regard to

the software products that you develop using the API; however, no software programs that you develop using the Intellex API or the

modular programs can be sold nor distributed by you to other entities as accessory products for Intellex product line without

authorization from Sensormatic.

OTHER RIGHTS AND LIMITATIONS

• A demonstration copy of the Software is considered purchased and is covered by this license agreement.

• The purchase order is your proof of license to exercise the rights granted herein and must be retained by you.

• You may not de-compile, disassemble, or reverse engineer any of the executables; including, but not limited to the library files, for

which you were not given the source code. The modular programs are excluded from this restriction and you may re-compile, re-

assemble, or alter any component of the source codes that are provided to you.

• You may not sub-license, rent or lease the software; nor permanently transfer the software to another party by delivering the

original media material comprising the software package as well as this license to the other party.

• Sensormatic reserves the right to revoke this agreement if you fail to comply with the terms and conditions of this agreement. In

such an event, you must destroy all the Intellex API software on and/or loaded from the purchased CD ROM, any API software

downloaded from the web or sent on “patch” media, all of the modular programs you modified and all the software programs that

you developed using the Intellex API.

• The software may contain software from third parties that is licensed under a separate End User License Agreement (EULA).

Read and retain any license documentation that may be included with the Software. Compliance with the terms of any third party

EULA is required as a condition of this agreement.

Failure to comply with these restrictions will result in automatic termination of this license and will make available to Sensormatic

other legal remedies.

COPYRIGHT

The software is a proprietary product of Sensormatic and is protected by both the United States and International copyright laws.

UPGRADES

If the software is an upgrade from another software version, or an upgrade of a component of a package of software programs that

you licensed you may use or transfer the software only as specified in this agreement.

LIMITED WARRANTY

Sensormatic warrants that the recording medium on which the software is recorded, and the documentation provided with it, will be

free of defects in materials and workmanship under normal use for a period of ninety (90) days from the date of delivery to the first

user. Sensormatic further warrants that for the same period, the software provided on the recording medium under this license will

substantially perform as described in the user documentation provided with the product when used with the specified hardware and

development environment.

CUSTOMER REMEDIES

Sensormatic’s entire liability and your exclusive remedy under this warranty will be, at Sensormatic’s option, to a). attempt to correct

software errors with efforts we believe suitable to the problem, b). replace at no cost the recording medium, software or

documentation with functional equivalents as applicable, or c). refund the license fee and terminate this agreement. Any replacement

item will be warranted for the remainder of the original warranty period. No remedy is provided for failure of the diskette or Software if

such failure is the result of accident, abuse, alteration or misapplication. Warranty service or assistance is provided at the original

point of purchase.

NO OTHER WARRANTIES

The above warranty is in lieu of all other warranties, express or implied, including, but not limited to the implied warranties of

merchantability and fitness for a particular purpose. No oral or written information or advice given by Sensormatic, its representatives,

distributors or dealers shall create any other warranty, and you may not rely on such information or advice.

NO LIABILITY FOR CONSEQUENTIAL DAMAGES

In no event will Sensormatic be liable to you for damages, including any loss of profits, loss of data or other incidental or

consequential damages arising out of your use of, or inability to use, the Software or its documentation. This limitation will apply even

vi

if Sensormatic or an authorized representative has been advised of the possibility of such damages. Further, Sensormatic does not

warrant that the operation of the Software will be uninterrupted or error free.

This limited warranty gives you specific legal rights. You may have other rights that vary from state to state. Some states do not allow

the exclusion of incidental or consequential damages, or the limitation on how long an implied warranty lasts, so some of the above

limitations may not apply to you.

GENERAL

If any provision of the agreement is found to be unlawful, void, or for any reason unenforceable, then that provision shall be severed

from this agreement and shall not affect the validity and enforceability of the remaining provisions. This agreement is governed by the

laws of the State of Florida.

You should retain proof of the license fee paid, including model number, serial number and date of payment, and present such proof

of payment when service or assistance covered by this warranty is requested.

U.S. GOVERNMENT RESTRICTED RIGHTS

The software and documentation are provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS

252.227-7013 or subparagraph (c)(1) and (2) of the Commercial Computer Software—Restricted Rights at 48 CFR 52.227-19, as

applicable. Manufacturer is Sensormatic Electronics Corporation, 6600 Congress Ave., Boca Raton, FL 33487.

Important Information

Before proceeding, please read and observe all instructions and warnings contained in this manual. Retain this manual with the

original bill of sale for future reference and, if necessary, warranty service.

When unpacking your Intellex unit, check for missing or damaged items. If any item is missing, or if damage is evident, DO NOT

INSTALL OR OPERATE THIS PRODUCT. Contact Sensormatic or your dealer for assistance.

For your Records

Complete the following product purchase information. The factory requests this information when contacted for technical support. It is

also valuable in case of loss or theft.

Purchase Date:

Serial Number:

License Key

The Intellex 4.0 software is protected from unauthorized use by a software license key. This key matches the electronic hardware of

your system with the authorized software version and feature level of your software to permit proper operation of your system. Any

changes to the network adapter in your unit, removal or modification of the license file, or replacement of the system disk will affect

normal operation and will require installation of a new license file. Please contact your authorized Sensormatic representative for

more information.

vii

Contents

Before Installing the Intellex

Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Programmable Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Video Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Video Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Record Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Rear Panel Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rack-mounted Intellex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Installing Hardware

Connecting Cameras and Peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Video Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting Audio Devices (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting Optional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Connecting Alarms to the Intellex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Connecting the Intellex to a Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Rack Mounting the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Ensuring Proper Rack Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Miscellaneous Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Configuring the Intellex

Configuring the Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Microsoft Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Exiting to Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Setting System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Setup Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Setting Up Cameras . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Gain Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Camera Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

User-Defined Handlers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Contents

viii Intellex® Ultra

Adding/Updating a User-Defined Camera Handler. . . . . . . . . . . . . . . . . . . . .22

Removing a User-Defined Camera Handler . . . . . . . . . . . . . . . . . . . . . . . . . . 23

PTZ Cameras. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Trigger Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Response Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Covert Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

Setting Up Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Regular Schedules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Setting Up Live Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting Up Motion Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting Up Perimeter Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Setting Up Light Change . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Setting Up Motion Exception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30

Select a Data Lifetime Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Setting Up Custom Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Setting Up a Custom Schedule for Weekends or Holidays. . . . . . . . . . . . . . . 32

Using Single Camera Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Setting Up Camera Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Adding, Editing, and Deleting Text Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Setting Up Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Setting Up Classic Security Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Policy Manager for Intellex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41

Setting Up Record Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Setting Up Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Setting Up Display Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Setting the Date and Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Setting Up the Port Address and Live Net Client Connections . . . . . . . . . . . . . . . 45

Setting Up Storage Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Setting Up the Archive Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Archiving All . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Setting up a Custom Archive Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46

Setting Up Email Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

Sending a Test Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Saving the Set Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

Configuring Anti-Virus Detection

Configuring the McAfee Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

Configuring the Symantec Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Custom Scan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54

Contents

Installation and Configuration Guide ix

RAID

Installing the Hard Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

3Ware 3DM2 Utility User’s Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Setting Up E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Adding a User to the E-mail Recipient List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Removing a User from the E-mail Recipient List . . . . . . . . . . . . . . . . . . . . . . . . . 58

Changing Events for E-mail Notification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Troubleshooting a RAID Problem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Offline Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Degraded Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Array Degraded Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Recovering RMS Offline Array to Functional System . . . . . . . . . . . . . . . . . . . . . . 60

Checking the Array Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Checking the Status of the Array in BIOS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Offline Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Setting Up a Logical Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Setting Up a Drive at the Intellex Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Questions & Answers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Intellex IP

Setting Up the Intellex IP System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Setting Up Parameters for IP Devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Setting the Record Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Setting Up the Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Connecting to Multiple Networks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Index 71

Contents

x Intellex® Ultra

1

Before Installing the Intellex

Safety Guidelines

• Ensure that installation work complies with electrical, fire, safety, communication, and building

codes and ordinances.

• Install the Intellex in a clean, dry location, where temperature and humidity are within product

specifications.

• Install the Intellex away from Electrical Magnetic Inducing (EMI) equipment, such as electrical

generators, motors, unshielded speakers, and high voltage cables.

• Allow adequate all-around clearance and accessibility for cables, peripherals, ventilation,

maintenance, and operation.

• Ensure that equipment is mounted level and securely.

• Ensure that equipment has a stable AC power source.

• Use of an Uninterruptible Power Supply (UPS) unit is highly recommended. UPS units protect

critical computing systems from power fluctuations and losses that may cause loss of data or

damage to the system.

• Install surge protectors on all power cables to protect against severe power fluctuations.

• Check the product label for power supply requirements to assure that no overloading of power

supply circuits or overcurrent protection occurs.

• Ensure that fans undergo periodic, scheduled maintenance and remain free and clear of dust.

• Electrical grounding must be reliable and uncompromised by any connections.

Note

The power supply automatically detects 115 or 230 volts input and has no power switch.

• Locate product documentation and software, and keep in a safe and accessible location.

• For all rack-mounted electrical equipment, ensure adequate air flow around the unit for safe

operation. The maximum temperature for rack-mounted units is 35° C or 95° F.

Note

Refer to the Intellex Ultra Quick Setup Guide for a visual overview of system contents, how to set

up and connect the components, and how to power up the unit.

Before Installing the Intellex

2 Intellex® Ultra

System Requirements

Note

This section includes system requirements for Intellex Ultra, DVMS, and LT.

Operating System: Intellex 4.0 software is compatible only with Microsoft XP Pro with embedded

restrictions

Note

* = a feature is enabled

Intellex 4.0

Hardware

Configuration

Ultra 8- and 16-Camera Rackmount LT

Hard drive

options

800 or 1600 GB 250 or 500GB 250, 500, or 750 GB 160 GB or 320 GB

Memory 512 MB 512 MB 512 MB 512 MB

Media drive Includes DVD-RW DVD-RW or CD-RW DVD-RW CD-RW

Chassis 3 U 4 U 4 U 4 U

Features Ultra DVMS LT-

16-Camera 8-Camera 4-

Camera

8-

Camera

16-

Camera

Number of cameras 16 16

8

4 8 16

Record rate 480 120

60

60 60 60

Client connections 10 10

10

5 5 5

Resolution 640 × 480

640 x 240

320 × 240

640 x 240

320 × 240

640 x 240

320 × 240

640 x 240

320 × 240

640 x 240

320 × 240

640 x 240

320 × 240

Multi-camera playback * *

*

Camera selectable

frame rates

* *

*

Video analysis tools * Premier only

User-defined camera

handler

* *

*

* * *

Advanced text * Premier only Premier

only

Alarm-triggered dome

actions

* *

*

* * *

Custom weekend * *

*

* * *

Hard drive failure

advance notification

* *

*

* * *

Network archive * *

*

Activity log * * *

Direct dome control

(USB-SNET)

* *

*

Email alarm/system

events

* *

*

* * *

Audio recording * Premier only Premier

only

Premier

only

Premier

only

Premier

only

Before Installing the Intellex

Installation and Configuration Guide 3

Text recording *

Premier

only

Premier

only

Premier

only

Premier

only

Premier

only

Tape archive * * *

Features Ultra DVMS LT-

16-Camera 8-Camera 4-

Camera

8-

Camera

16-

Camera

Before Installing the Intellex

4 Intellex® Ultra

Programmable Settings

Video Format

Video Level

Alarm

Display

Setting Default Value

Camera names Camera1–Camera16

Camera termination 75 Ω

Security access Disabled

Administrator PIN 1234

Schedule mode Regular

Record settings Circular Mode, normal sensitivity, 60 ips (50 ips PAL)

Alarm duration 5 seconds

Alarm record settings 30 ips (25 ips PAL), normal quality, normal sensitivity

Alarm on video loss Enabled

Alarm display message Enabled

Latch message Disabled

Alarm input names AlarmIn1–AlarmIn16

Alarm input polarity Active Low

Live sequencer dwell 2 seconds

Live display format 1×1

Playback overlay Enabled, Upper-Right

Color (input and output) NTSC or PAL

B&W (input and output) EIA or CCIR

Camera inputs 1.0 V p-p, 75 Ω

Camera outputs 1.0 V p-p, 75 Ω

Analog output 1.0 V p-p, 75 Ω

Alarm inputs 4, 8, or 16 inputs. Activated by contact closure or TTL/CMOS signal.

Programmable polarity.

Alarm outputs 4, 8, or 16 outputs. TTL/CMOS compatible active high. Driven to +4V and

can drive 6mA. Initialized to inactive low on power-up.

Alarm duration Programmable from 5 seconds – 5 minutes.

Color palette 16,777,216 colors (32 bits)

Gray shades 256 (8 bits)

Display controls Mouse-selectable buttons with indicator lights

Before Installing the Intellex

Installation and Configuration Guide 5

Note

Pixel count reflects the digital display area and is not affected by NTSC/PAL signal differences.

Record Options

Rear Panel Connectors

Note

* = with optional looping board

** = 16-camera only

Format Menu Mode Full Screen Mode

1×1 640×480 (pixels) 800×600

2×2 320×240 400×300

3×3 213×160 267×200

4×4 (16 channel

only)

160×120 200×150

Record mode Linear, Circular

Image sensitivity High, Normal

Image quality Super, Normal, Extended Record

Record rate

Ultra

NTSC: 480, 240, 120, 60, 30, 15, 7.5, 2.5,

and 1 ips (images per second)

PAL: 400, 200, 100, 50, 25, 12.5, 6.25, 2,

and 0.8 ips

DVMS

NTSC: 120, 60, 30, 15, 7.5, 2.5, and 1 ips

PAL: 100, 50, 25, 12.5, 6.25, 2, and 0.8

ips

LT:

NTSC: 60, 30, 15, 7.5, and 2.5 ips

PAL: 50, 25, 12.5, 6.25, and 2 ips

Connector Use Applies to

Intellex:

Camera In BNC. Composite video input from camera. Ultra, DVMS, LT

Camera Out BNC. Composite video output from camera (passive loop

through). Termination is set within Intellex.

Ultra*, DVMS**, LT**

Alarm Connector block with screw terminals. Ultra, DVMS, LT

Keyboard Standard PS/2-style connector. All (not supplied)

Mouse Input device with standard PS/2-style connector. All

USB These connectors are used to add RS-232 ports, data

storage devices, USB-Sensornet dome control modules,

and other accessories to the Intellex.

All

Monitor HD15-S. SVGA monitor output for live display. All

Call Monitor

(Composite)

BNC composite output to optional call monitor display. Ultra, DVMS**, LT**

TV Out

(Composite)

Composite video output. DVMS, LT

TV Out (S-Video) S-Video. Composite video output. Ultra, DVMS**

Before Installing the Intellex

6 Intellex® Ultra

Power Supply

Environmental Requirements

Caution

Intellex Operating Temperature Range

The specified operating temperature range for the Intellex Ultra is 5° C to 35° C (41° F to 95° F). The product

meets all functional specifications in this temperature range, and all of the internal components are within their

manufacturers’ specified temperature limits. Extended operation at elevated temperatures reduces the life of

electronic components and reduces overall system reliability. It is recommended that the ambient temperature be

maintained at 15°

C to 24° C (59° F to 75° F) to maximize the life of the electronic components. The ambient

temperature is the air temperature in the immediate vicinity of the chassis. For example, if the chassis is mounted in

a rack or lock box, the ambient temperature is the air temperature within the rack or lock box.

Printer DB25-S. Parallel printer output. All

Serial DB9-P. Dome controller (Sensormatic VM16 or American

Dynamics ADTT16) input.

All

SCSI-3 High density 68-pin female connector. For use with

external storage devices.

Optional

Network RJ-45. Category 3 or Category 5 twisted-pair Ethernet

(CAT 3 TPE or CAT 5 TPE) connector.

All

Microphone Compatible with dynamic, condenser, and electret

microphones. Line input is compatible with 1 Vrms line

level audio sources.

All (optional on IP)

Connector Use Applies to

Intellex:

Input 100 - 240 VAC, 50-60 Hz, less than 5A

Requires IEC-320-C13 plug

Temperature 41–95° F (5–35° C)

Humidity 5–95% RH noncondensing

Storage temperature 14° –140° F (10–60° C)

Before Installing the Intellex

Installation and Configuration Guide 7

Front Panel

4_0FP_1

POWER

REC

ALARM

DVD-RW Drive

USB Connectors

Hard drives

Power indicator

Alarms indicator

• Illuminates when alarm events

occur but have not been reviewed.

• Blinks when the notification screen

appears.

REC (recording indicator)

illuminates when the unit

records images to the

image database.

Ultra

3

_

2FP

_

1

Power indicator

Power: Insert the reset tool into

the pinhole to power on or off.

Reset: If the unit does not power

on, insert the reset tool into the

pinhole to reset. The unit powers

on and performs standard

diagnostics.

Alarms indicator

• Illuminates when alarm events

occur but have not been reviewed.

• Blinks when the notification screen

appears.

REC (recording indicator)

illuminates when the unit records

images to the image database.

3½-inch diskette

drive

CD-RW/DVD Drive

DVMS/LT

Power switch

Reset switch

Before Installing the Intellex

8 Intellex® Ultra

Rack-mounted Intellex

Do not modify any BIOS or system settings or reconfigure any hard drives. During power-up, the

Intellex splash screen appears. During initial power-up, a message may appear. Do not press

buttons on the front panel or keys on the keyboard until this screen and message disappears,

which may take 2 minutes. Otherwise, you may interrupt the start-up process and affect the unit’s

operation. Double-clicking the Intellex icon during the start-up process can lock the Intellex or

cause it to go into an unrecoverable condition.

3

_

2FP

_

1

Fan

Reset button

Power indicator

Alarms indicator

Hard drive activity

Power switch

CD Drive

9

Installing Hardware

Connecting Cameras and Peripherals

Caution

Protect the unit against lightning. If part of a cable is installed outside a building, the entire cable is

vulnerable to lightning. Install surge protectors on all vulnerable cables.

Video Devices

1 Connect the cameras:

a Connect the video cables from the cameras to the left BNC connector of each pair of

connectors on the rear of the unit.

b Terminate the video using the switches at each BNC connector (8-camera system) or the

Intellex Setup screen. If you use the switches to select the 75

Ω termination, select Hi-Z

from the Intellex Setup screen. See

page 19.

Note

To use the Intellex Setup screen to select the 75 Ω termination, set the switches at each BNC to

infinity.

2 Connect any External Storage Modules (ESMs) through the Firewire connectors.

3 Connect the VGA cable from an SVGA monitor to the VGA monitor connector.

Installing Hardware

10 Intellex® Ultra

4 Connect an optional call monitor to the BNC connector on the Call Monitor board to see live

video from a single camera (call mode) or from alarmed cameras in sequence (spot mode).

Connecting Audio Devices (optional)

1 Connect the microphone or audio source to the Intellex unit through the color-coded 3.5 mm

audio connectors on the back of the unit.

For the best quality sound, use a pre-amplifier with appropriate filtering with a compatible

microphone.

INT40

_

BP

BNC Camera in

VGA monitor

VACD 3

Power entry Mouse

Glan 1

Glan 2

Sound

card

Ultra

3

_

2BP

_

1

Call Monitor BNC

Ethernet 10/100

Power entry

Mouse

VGA monitor

BNC Camera in

Passive loop through/

camera out

DVMS/Rackmount

Page is loading ...

American Dynamics Intellex Intellex Ultra Installation And Configuration Manual

This manual is also suitable for

American Dynamics Intellex Intellex Ultra Installation And Configuration Manual

Related papers

Other documents