www.moogvideolarm.com
L I B E RT Y ™ S e r i e s
City-Wide Surveillance
Installation and Operation Instructions for the following models:
PB26LG Liberty Series wireless power box that includes a cellular router and
power supply. 110/220VAC input. Designed to work with Moog
Videolarm’s IP Ready Series of IP camera housings.
Before attempting to connect or operate this product, please read these instructions completely.
81-IN5459
10-23-2012
© 2012, Moog Videolarm, Inc. All Rights Reserved
IMPORTANT SAFEGUARDS SAFETY PRECAUTIONS
UNPACKING
SERVICE
1 Read these instructions.
2 Keep these instructions.
3 Heed all warnings
4 Follow all instructions.
5 Do not use this apparatus near water.
6 Clean only with damp cloth.
7 Do not block any of the ventilation openings. Install in accordance with the
manufacturers instructions.
8 Cable Runs- All cable runs must be within permissible distance.
9 Mounting - This unit must be properly and securely mounted to a supporting
structure capable of sustaining the weight of the unit.
Accordingly:
a. The installation should be made by a qualified installer.
b. The installation should be in compliance with local codes.
c. Care should be exercised to select suitable hardware to install the unit, taking into
account both the composition of the mounting surface and the weight of the
unit.
10 Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus ( including amplifiers) that produce heat.
11 Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade or the third
prong are provided for your safety. When the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
12 Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
13 Only use attachment/ accessories specified by the manufacturer.
14 Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
15 Unplug this apparatus during lighting storms or when unused for long periods of time.
16 Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled of objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
Be sure to periodically examine the unit and the supporting structure to make sure that the
integrity of the installation is intact. Failure to comply with the foregoing could result in the
unit separating from the support structure and falling, with resultant damages or injury to
anyone or anything struck by the falling unit.
Unpack carefully. Electronic components can be
damaged if improperly handled or dropped. If an item
appears to have been damaged in shipment, replace
it properly in its carton and notify the shipper.
Be sure to save:
1 The shipping carton and packaging material.
They are the safest material in which to make
future shipments of the equipment.
2 These Installation and Operating Instructions.
If technical support or service is needed, contact us
at the following number:
The lightning flash with an arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of non-insulated “dangerous voltage”
within the product’s enclosure that may be
of sufficient magnitude to constitute a risk
to persons.
Este símbolo se piensa para alertar al usuario a la
presencia del “voltaje peligroso no-aisIado” dentro del
recinto de los productos que puede ser un riesgo de
choque eléctrico.
Ce symbole est prévu pour alerter I’utilisateur à la
presence “de la tension dangereuse” non-isolée dans la
clôture de produits qui peut être un risque de choc
électrique.
Dieses Symbol soll den Benutzer zum Vorhandensein der
nicht-lsolier “Gefährdungsspannung” innerhalb der
Produkteinschließung alarmieren die eine Gefahr des
elektrischen Schlages sein kann.
Este símbolo é pretendido alertar o usuário à presença
“di tensão perigosa non-isolada” dentro do cerco dos
produtos que pode ser um risco de choque elétrico.
Questo simbolo è inteso per avvertire I’utente alla
presenza “di tensione pericolosa” non-isolata all’interno
della recinzione dei prodotti che può essere un rischio di
scossa elettrica
.
The exclamation point within an equilateral
triangle is intended to alert the user to
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Este símbolo del punto del exclamation se piensa para
alertar al usuario a la presencia de instrucciones
importantes en la literatura que acompaña la
aplicación.
Ce symbole de point d’exclamation est prévu pour
alerter l’utilisateur à la presence des instructions
importantes dans la littérature accompagnant
l’appareil.
Dieses Ausruf Punktsymbol soll den Benutzer zum
Vorhandensein de wichtigen Anweisungen in der
Literatur alarmieren, die das Gerät begleitet.
Este símbolo do ponto do exclamation é pretendido
alertar o usuário à presença de instruções importantes
na literatura que acompanha o dispositivo.
Questo simbolo del punto del exclamaton è inteso per
avvertire l’utente alla presenza delle istruzioni importanti
nella letteratura che accompagna l'apparecchio.
TECHNICAL SUPPORT
AVAILABLE 24 HOURS
1- 800 - 554 -1124
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER ( OR BACK). NO USER- SERVICE-
ABLE PARTS INSIDE. REFER SEVICING TO
QUALIFIED SERVICE PERSONNEL.
Limited Warranty for Moog Videolarm Products
Moog Videolarm warrants these products to be free from defects in material or workmanship as follows:
PRODUCT CATEGORY PARTS \ LABOR
All Enclosures and Electronics* Five (5) Years
Poles/PolEvators™/CamEvator Three (3) Years
Warrior Series™/Q-View™/IR Illuminators Five (5) Years
SView Series™ Five (5) Years **6 months if used in auto scan/tour operation
Controllers Five (5) Years
Power Supplies Five (5) Years
EcoKit Three (3) Years
Accessory Brackets Five (5) Years
Liberty Dome Three (3) Years
*DeputyDome™, NiteTrac™, Igloo Dome, PurgeDome™ Three (3) Years **6 months if used in auto scan/tour operation
During the labor warranty period, to repair the Product, Purchaser will either return the defective product, freight prepaid, or deliver it to Moog Videolarm
Inc. Decatur GA. The Product to be repaired is to be returned in either its original carton or a similar package affording an equal degree of protection with
a RMA # (Return Materials Authorization number) displayed on the outer box or packing slip. To obtain a RMA# you must contact our Technical Support
Team at 800.554.1124, extension 101. Moog Videolarm will return the repaired Product freight prepaid to Purchaser. Moog Videolarm is not obligated to
provide Purchaser with a substitute unit during the warranty period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or
parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions.
TERMS AND CONDITIONS
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice with an
explanation of the claim shall be given promptly by Purchaser to Moog Videolarm. All claims for warranty service must be made within the warranty period.
If after investigation Moog Videolarm determines the reported problem was not covered by the warranty, Purchaser shall pay Moog Videolarm for the cost of
investigating the problem at its then prevailing per incident billable rate. No repair or replacement of any Product or part thereof shall extend the warranty period
of the entire Product. The speci c warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that
part or the remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Moog Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair any
Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Moog Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during the
warranty period which is subjected to any of the following: abuse, improper use, negligence, accident, lightning damage or other acts of God (i.e., hurricanes,
earthquakes), modi cation, failure of the end-user to follow the directions outlined in the product instructions, failure of the end-user to follow the maintenance
procedures recommended by the International Security Industry Organization, written in product instructions, or recommended in the service manual for the
Product. Furthermore, Moog Videolarm shall have no liability where a schedule is speci ed for regular replacement or maintenance or cleaning of certain parts
(based on usage) and the end-user has failed to follow such schedule; attempted repair by non-quali ed personnel; operation of the Product outside of the
published environmental and electrical parameters, or if such Product’s original identi cation (trademark, serial number) markings have been defaced, altered,
or removed. Moog Videolarm excludes from warranty coverage Products sold AS IS and/or WITH ALL FAULTS and excludes used Products which have not
been sold by Moog Videolarm to the Purchaser. All software and accompanying documentation furnished with, or as part of the Product is furnished “AS IS”
(i.e., without any warranty of any kind), except where expressly provided otherwise in any documentation or license agreement furnished with the Product. Any
cost associated with removal of defective product and installation of replacement product is not included in this warranty.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY
EXCEPT FOR THE FOREGOING WARRANTIES, Moog Videolarm HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO ANY AND/OR ALL IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND/OR
ANY WARRANTY WITH REGARD TO ANY CLAIM OF INFRINGEMENT THAT MAY BE PROVIDED IN SECTION 2-312(3) OF THE UNIFORM COMMERCIAL
CODE AND/OR IN ANY OTHER COMPARABLE STATE STATUTE. Moog Videolarm HEREBY DISCLAIMS ANY REPRESENTATIONS OR WARRANTY THAT
THE PRODUCT IS COMPATIBLE WITH ANY COMBINATION OF NON-Moog Videolarm PRODUCTS OR NON-Moog Videolarm RECOMMENDED PRODUCTS
PURCHASER MAY CHOOSE TO CONNECT TO THE PRODUCT.
LIMITATION OF LIABILITY
THE LIABILITY OF Moog Videolarm, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND
WHATSOEVER, REGARDLESS OF THE LEGAL THEORY AND WHETHER ARISING IN TORT OR CONTRACT, SHALL NOT BE GREATER THAN THE ACTUAL
PURCHASE PRICE OF THE PRODUCT WITH RESPECT TO WHICH SUCH CLAIM IS MADE. IN NO EVENT SHALL Moog Videolarm BE LIABLE TO PURCHASER
FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO, COMPENSATION,
REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.
PB26LG
Energía De Entrada: 110 Consumo De Energía de VAC/220VAC 1A/.5A:
1Amp (120 vatios) en 120 VAC de salida de energía: VA 96 en 24 VAC
52 vatios de Heater/Blower 32 vatios de energía de la cámara
fotográca
Todo el interruptor principal del poste con un contacto de por lo
menos 3m m en cada poste será incorporado en la instalación
eléctrica del edicio.
Herramientas Requeridas: destornillador de cabeza llana del 150"7/16
llave de la llave o del zócalo 9/16 o zócalo
Puissance D'entrée : 110 Puissance D'Énergie de VAC/220VAC 1A/.5A :
1Amp (120 watts) à 120 VCA de rendement de puissance: VA 96 à 24
VCA 52 watts de Heater/Blower 32 watts de puissance d'appareil-
photo
Un tout le commutateur principal de poteau avec un contact au moins
de 3mm dans chaque poteau sera incorporé dans l'installation
électrique du bâtiment.
Outils Requis: tournevis à tête plate de 150"7/16 clé de clé ou de douille
9/16 ou douille
Zugeführte Energie: 110 VAC/220VAC 1A/.5A
Leistungsaufnahme: 1Amp (120 Watt) bei 120 VAC
Abgabeleistung: VA 96 bei 24 VAC 52 Watt
Heater/Blower 32 Watt Kamera-Energie
Ein aller Pfostenhauptschalter mit einem Kontakt von 3mm mindestens
in jedem Pfosten wird in der elektrischen Installation des Gebäudes
enthalten.
Werkzeuge Erforderten: 150"Flachkopfschraubenzieher 7/16 Schlüssel-
oder Einfaßung 9/16 Schlüssel oder Einfaßung
Poder De Entrada: 110 Consumo De Potência de VAC/220VAC 1A/.5A:
1Amp (120 watts) em 120 VAC de saída de poder: VA 96 em 24 VAC
52 watts de Heater/Blower 32 watts de poder da câmera
Todo o interruptor principal do pólo com um contato ao menos de
3mm em cada pólo será incorporado na instalação elétrica do edifício.
As Ferramentas Requereram: chave de fenda athead do 150"7/16 de
chave da chave ou do soquete 9/16 ou soquete
Alimentazione in ingresso Di Entrata: 110 Assorbimento di corrente Di
energia di VAC/220VAC 1A/.5A: 1Amp (120 watt) a 120 VCA di uscita
di alimentazione: VA 96 a 24 VCA 52 watt di Heater/Blower 32 watt di
alimentazione della macchina fotograca
Tutto l'interruttore principale del palo con un contatto almeno di 3mm
in ogni palo sarà compreso nell'installazione elettrica della costruzione.
Attrezzi Richiesti: cacciavite a testa piatta del 150"7/16 di chiave dallo
zoccolo o dalla chiave 9/16 o zoccolo
Input Power: 110 VAC/220VAC 1A/.5A
Power Consumption: 1Amp (120 Watts) at 120 VAC
Power Output: 96 VA at 24 VAC 52 Watts
Heater/Blower 32 Watts Camera Power
An all pole main switch with a contact of at least 3mm in each
pole shall be incorporated in the electrical installation of the
building.
Tools Required: .150” Flathead Screwdriver 7/16 Wrench or Socket
9/16 Wrench or Socke
t
Electrical Specications
Français
Deutsch
Italiano
Portuguese
Español
English
Contents of Box
Power Feed Locations:
Pendant
mount location
Liquid tight strain
relief for main
power
Liquid tight
plug for optional
power / antenna
Liquid tight
modem cover
3G - 4G units
Liquid tight
security latch
WALL MOUNTING
POLE MOUNTING
Attach unit securely with (4) ⅜” bolts.
• Ate la unidad con seguridad con (4) pernos del ⅜ los”.
• Attachez l'unité solidement avec (4) boulons
de ⅜ des ».
• Bringen Sie Maßeinheit sicher mit (4) ⅜“
Schraubbolzen an.
• Una a unidade firmemente com (4) parafusos do ⅜”.
• Attacchi saldamente l'unità con (4) bulloni del ⅜„.
Step One: Attach the pole clips to the mounting
tabs as shown. Use hardware provided.
• Paso uno: Ate los clips del poste a las lengüetas del montaje
como se muestra. Utilice el hardware proporcionado.
• Étape une : Attachez les agrafes de poteau aux étiquettes de
support comme montrées. Utilisez le matériel fourni.
• Schritt einer: Bringen Sie die Pfostenclips zu den
Montagevorsprüngen wie gezeigt an. Benutzen Sie die
bereitgestellte Hardware.
• Etapa uma: Una os grampos do pólo às abas da montagem
como mostradas. Use a ferragem fornecida.
• Punto uno: Attacchi le clip del palo alle linguette del
montaggio come indicate. Utilizzi i fissaggi forniti.
Step Two: PB26LG is ready to mount. Use slots
to attach steel straps.
• Paso dos: PB26LG está listo para montar. Utilice las
ranuras para atar las correas de acero.
• Étape deux : PB26LG est prêt à monter. Employez les
fentes pour attacher les courroies en acier.
• Schritt zwei: PB26LG ist bereit anzubringen. Benutzen Sie
Schlitze, um Stahlbügel anzubringen.
• Etapa dois: PB26LG está pronto para montar. Use
entalhes para unir as cintas de aço.
• Punto due: PB26LG è pronto a montare. Usi le
scanalature per attaccare le cinghie d'acciaio.
Step Three: Use steel straps to mount the
unit to a pole.
• Paso tres: Utilice las correas de acero para montar la
unidad a un poste.
• Étape trois : Employez les courroies en acier pour
monter l'unité à un poteau.
• Schritt drei: Benutzen Sie Stahlbügel, um die Maßeinheit
zu einem Pfosten anzubringen.
• Etapa três: Use as cintas de aço para montar a
unidade a um pólo.
• Punto tre: Usi le cinghie d'acciaio per montare l'unità
ad un palo.
1
3
2
4
Inside view of the unit.
• Dentro de la vista de la unidad.
• Dessus à l'intérieur de la vue de l'unité.
• Innerhalb der Ansicht der Maßeinheit.
• Dentro da ideia da unidade.
• All'interno della vista dell'unità.
The wall mount bracket must be attached
using the gasket as shown.
• El soporte del montaje de la pared se debe atar usando la
junta como se muestra.
• La parenthèse de bâti de mur doit être attachée utilisant la
garniture comme montrée.
• Der Wandeinfassungshaltewinkel muss unter Verwendung
der Dichtung wie gezeigt angebracht werden.
• O suporte da montagem da parede deve ser unido usando
a gaxeta como mostrado.
• La staffa del supporto della parete deve essere attaccata
per mezzo della guarnizione come indicata.
Wall Mount
Gasket
This is the assembled unit with the housing
and conduit.
• Ésta es la unidad montada con la cubierta
y el conducto.
• C'est l'unité assemblée avec le logement
et le conduit.
• Dieses ist die zusammengebaute Maßeinheit mit dem
Gehäuse und dem Rohr.
• Esta é a unidade montada com a carcaça
e a canalização.
• Ciò è l'unità montata con l'alloggiamento
ed il condotto.
Conduit Fittings
5
6
7
PENDANT MOUNTING
Remove
barrier
cover
Remove barrier cover.
• Quite la cubierta de la barrera.
• Enlevez la couverture de barrière.
• Entfernen Sie Sperrenabdeckung.
• Remova a tampa da barreira.
• Rimuova la copertura della barriera.
o della vista dell'unità.
8
ON/OFF switch
(will not turn off
wireless circuit)
115/240VAC
selector switch
120/240VAC
input
12VDC output
24VAC
Aux. output
120/240VAC
Aux. output
1. Move the 115//240VAC selector switch (3) to the
desired position
2. Insure that the ON/OFF switch (2) is in the off position
3. Attach the in coming “main” power to the 120/240 VAC input
4. Move the ON/OFF switch (2) to the ON position.
• 1. Mueva el interruptor de selector 115//240VAC (3) a
la posición deseada
2. Asegure que el interruptor CON./DESC. (2) está en la
posición de reposo
3. Ate en energía “principal” que viene a la entrada de 120/240
VAC 4. Mueva el interruptor CON./DESC. (2) a la posición de trabajo.
• 1. Déplacez le sélecteur 115//240VAC (3) à la position désirée
2. Assurez-vous que le commutateur "MARCHE/ARRÊT" (2) est dans la
position de repos
3. Attachez dans la prochaine puissance « principale » à l'entrée de
120/240 VCA
4. Déplacez le commutateur "MARCHE/ARRÊT" (2) à la
position de fonctionnement.
• 1. Verschieben Sie den Schalter des Wähl 115//240VAC (3) auf die
gewünschte Position
2. Versichern Sie, dass der Ein/Aus-Schalter (2) in der Ausschaltstellung ist
3. Bringen Sie in kommender „Haupt“ Energie zum 120/240 VAC-
Eingang an
4. Verschieben Sie den Ein/Aus-Schalter (2) auf die Arbeitsstellung.
• 1. Mova o interruptor de seletor 115//240VAC (3) para a
posição desejada
2. Segure que o interruptor DE LIGAR/DESLIGAR (2) está no
posição de repouso
3. Una no poder “principal” de vinda à entrada de 120/240 de VAC
4. Mova o interruptor DE LIGAR/DESLIGAR (2) para o
posição de functionamento.
• 1. Sposti l'interruttore di selettore 115//240VAC (3) alla posizione voluta
2. Assicuri che l'interruttore acceso/spento (2) è nella posizione di riposo
3. Attacchi nel potere “principale„ venente all'input da 120/240 di VCA
4. Sposti l'interruttore acceso/spento (2) alla posizione di funzionamento.
9
Assign your camera the static TCP/IP address of
192.168.1.50 with a subnet mask of 255.255.255.0 and a
gateway of 192.168.1.1.
• Asigne a su cámara la dirección estática del TCP/IP de 192.168.1.50 con
un subnet mask de 255.255.255.0 y una entrada de 192.168.1.1.
• Assignez à votre appareil-photo l'adresse statique de TCP/IP de
192.168.1.50 avec un subnet mask de 255.255.255.0 et un passage de
192.168.1.1.
• Weisen Sie Ihrer Kamera die statische IP-Adresse von 192.168.1.50 mit
einem subnet mask von 255.255.255.0 und einem Zugang von
192.168.1.1 zu.
• Atribua a sua câmera o endereço de estática do TCP/IP de 192.168.1.50
com um subnet mask de 255.255.255.0 e uma passagem de 192.168.1.1.
• Assegni alla vostra macchina fotografica l'indirizzo statico del TCP/IP di
192.168.1.50 con un subnet mask di 255.255.255.0 e un ingresso di
192.168.1.1.
3G/4G Camera Prep
Connect to your camera with a laptop or pc
• Conecte con su cámara con un ordenador portátil o
una PC.
• Reliez à votre appareil-photo à un ordinateur portable
ou à un PC.
• Schließen Sie an Ihre Kamera an einen Laptop oder an
einen PC an.
• Conecte a sua câmera com um portátil ou um PC.
• Colleghi alla vostra macchina fotografica con un
computer portatile o un pc.
10
11
Change to HTTP port from the default port 80 to
the port 12345.
• Cambie al puerto del HTTP del puerto 80 del defecto al puerto 12345.
• Changez en le port de HTTP du port 80 de défaut en port 12345.
• Ändern Sie zum HTTP-Hafen vom Rückstellungshafen 80 zum Hafen
12345.
• Mude ao porto do HTTP do porto 80 do defeito ao porto 12345.
• Cambi all'orificio del HTTP dall'orificio 80 di difetto all'orificio 12345.
USB 3G/4G Card Prep
When ordering your service with your provider, have
them add a static ip address to the service <extra
charge may be involved>
• Al pedir su servicio con su abastecedor, haga que agreguen un IP
address estático al servicio (el recargo puede estar implicado).
• En commandant votre service avec votre fournisseur, faites-ajouter les
un IP address statique au service (le supplément peut être impliqué).
• Wenn Sie Ihren Service mit Ihrem Versorger bestellen, lassen Sie sie ein
statisches IP address dem Service hinzufügen (Extragebühr kann
beteiligt sein) .
• Ao requisitar seu serviço com seu fornecedor, mande-os adicionar um
IP address de estática ao serviço (a sobretaxa pode ser involvida.
• Nell'ordinare il vostro servizio con il vostro fornitore, facciali aggiungere
un IP address statico al servizio (la carica supplementare può essere
implicata).
12
13
Some users may require WiFi access to the unit as well. Connect to the WiFi
network by selecting the SSID that contains the word Videolarm and a
combination of three letters and numbers. An example is Videolarm2A0 as
shown above. The encryption key for the network is password.
• Algunos usuarios pueden requerir el acceso de WiFi a la unidad también. Conecte con la red de
WiFi seleccionando el SSID que contiene la palabra Videolarm y una combinación de tres letras y
números. Un ejemplo es Videolarm2A0 como se muestra arriba. La llave de encripción para la red
es contraseña.
• Quelques utilisateurs peuvent avoir besoin de l'accès de WiFi à l'unité aussi bien. Reliez au réseau de
WiFi en choisissant le SSID qui contient le mot Videolarm et une combinaison de trois lettres et
nombres. Un exemple est Videolarm2A0 comme montré ci-dessus. La clef de chiffrage pour le
réseau est mot de passe.
• Einige Benutzer können WiFi Zugang zur Maßeinheit außerdem fordern. Schließen Sie an das WiFi
Netz an, indem Sie das SSID vorwählen, das das Wort Videolarm und eine Kombination von drei
Buchstaben und von Zahlen enthält. Ein Beispiel ist Videolarm2A0 wie gezeigt oben. Der
Verschlüsselungschlüssel für das Netz ist Kennwort.
• Alguns usuários podem exigir o acesso de WiFi à unidade também. Conecte à rede de WiFi
selecionando o SSID que contem a palavra Videolarm e uma combinação de três letras e
números. Um exemplo é Videolarm2A0 como mostrado acima. A chave de cifragem para a rede
é senha.
• Alcuni utenti possono richiedere l'accesso di WiFi all'unità pure. Colleghi alla rete di WiFi
selezionando lo SSID che contiene la parola Videolarm e una combinazione di tre lettere e numeri.
Un esempio è Videolarm2A0 come indicato sopra. La chiave di crittografia per la rete è parola
d'accesso.
14
Connecting to the WiFI network allows a connection to the admin interface
on the address http://192.168.1.1 as well as local access to the camera on
address http://192.168.1.50:12345. The username for the admin interace is
root with a password of admin.
• La conexión con la red de WiFI permite una conexión al interfaz del admin en la
dirección http://192.168.1.1 así como el acceso local a la cámara en la dirección
http://192.168.1.50:12345.
El username para el interace del admin es raíz con una contraseña del admin.
• Se relier au réseau de WiFI permet un raccordement à l'interface d'admin sur
l'adresse http://192.168.1.1 aussi bien que l'accès local à l'appareil-photo sur
l'adresse http://192.168.1.50:12345. L'username pour l'interace d'admin est racine
avec un mot de passe d'admin.
• Die Verbindung an das WiFI Netz erlaubt einen Anschluss zur admin-Schnittstelle auf
der Adresse http://192.168.1.1 sowie lokalen Zugang zur Kamera auf Adresse
http://192.168.1.50:12345. Das username für das admin interace ist Wurzel mit
einem Kennwort von admin.
• Conectar à rede de WiFI permite uma conexão à relação do admin no endereço
http://192.168.1.1 assim como o acesso local à câmera no endereço
http://192.168.1.50:12345. O username para o interace do admin é raiz com uma
senha do admin.
• Collegandosi alla rete di WiFI permette un collegamento all'interfaccia di admin
sull'indirizzo http://192.168.1.1 così come accesso locale alla macchina fotografica
sull'indirizzo http://192.168.1.50:12345. Il username per il interace di admin è radice
con una parola d'accesso del admin.
15
Advanced configuration options for changing the WiFI settings, etc. are
available through the admin interface.
• Las opciones de configuración avanzadas para cambiar los ajustes de WiFI, el etc.
están disponibles a través del interfaz del admin.
• Les options de configuration avancées pour changer les arrangements de WiFI,
etc. sont disponibles par l'interface d'admin.
• Vorgerückte Konfigurationswahlen für das Ändern der WiFI Einstellungen, des etc.
sind durch die admin-Schnittstelle vorhanden.
• As opções de configuração avançadas para mudar os ajustes de WiFI, etc. estão
disponíveis através da relação do admin.
• Le opzioni di configurazione avanzate per il cambiamento le regolazioni di WiFI,
ecc. sono disponibili attraverso l'interfaccia di admin.
16
Use the provided velcro to mount and secure the USB modem.
• Utilice el Velcro proporcionado para montar y para asegurar el módem del USB.
• Employez le Velcro fourni pour monter et fixer le modem d'USB.
• Benutzen Sie den zur Verfügung gestellten Flausch, um das USB-Modem anzubringen und zu sichern.
• Use o Velcro fornecido para montar e fixar o modem do USB.
• Usi il Velcro fornito per montare e fissare il modem del USB.
17
Assemble the modem cover as shown.
• Utilice el Velcro proporcionado para montar y para asegurar el módem del USB.
• Employez le Velcro fourni pour monter et fixer le modem d'USB.
• Benutzen Sie den zur Verfügung gestellten Flausch, um das USB-Modem anzubringen und zu sichern.
• Use o Velcro fornecido para montar e fixar o modem do USB.
• Usi il Velcro fornito per montare e fissare il modem del USB.
SCREW
SPLIT WASHER
FLAT WASHER
CLAMP RING
CARD COVER
GASKET
FLAT WASHER
HEX NUT
18
MODEM - INSTALL
LID - INSTALL (3G - 4G)
SUPPORT FOR 3G/4G CARDS:
The PB26LG can support cards up to 5.25” x 1.45” x .5” ( L x W x D ) in size. Some cards may have intermittent service operating
at temperatures above (122°F).
INPUT FOR CAMERA
24VAC POWER FOR
CAAMERA AND HOUSING
ALARM INPUT FOR IP RESET
120VAC INPUT
Attach 120VAC main power to connector.
• Ate la alimentación principal 120VAC
al conectador.
• Attachez l'alimentation secteur 120VAC
au connecteur.
• Bringen Sie Netzspannung 120VAC zum
Verbindungsstück an.
• Una o poder 120VAC principal ao conector.
• Attacchi la alimentazione di rete
120VAC al connettore.
Connect down and camera power to this connector green wire and yellow
wire are for housing heater and blower. Red/black and orange/black are
for camera power. Because it is 24VAC. It is not polarity sensative.
• Conecte abajo y la energía de la cámara a este alambre del verde del
conectador y al alambre amarillo está para el calentador y el soplador de la
cubierta. Rojo/negro y naranja/negro esté para la energía de la cámara. Porque
es 24VAC. No es polaridad sensative.
• Reliez vers le bas et la puissance d'appareil-photo à ce fil de vert de connecteur
et à fil jaune sont pour le réchauffeur et le ventilateur de logement. Rouge/noir et
orange/noir soyez pour la puissance d'appareil-photo. Puisque c'est 24VAC. Ce
n'est pas polarité sensative.
• Schließen Sie unten an und Kameraenergie zu diesem Verbindungsstückgrün-
draht und zum gelben Draht sind für Gehäuseheizung und -gebläse.
Rot/Schwarzes und Orange/Schwarzes seien Sie für Kameraenergie. Weil es
24VAC ist. Es ist nicht die sensative Polarität.
• Conecte para baixo e o poder da câmera a este fio do verde do conector e ao
fio amarelo é para o calefator e o ventilador da carcaça. Vermelho/preto e
laranja/preto seja para o poder da câmera. Porque é 24VAC.
Não é polaridade sensative.
• Colleghi giù ed il potere della macchina fotografica a questo legare di verde del
connettore ed a legare giallo è per il riscaldatore ed il ventilatore
dell'alloggiamento. Rosso/nero ed arancio/nero sia per potere della macchina
fotografica. Poiché è 24VAC. Non è polarità sensative.
19
20
21
Connect network camera to network cable.
• Conecte la cámara de red con el cable
de la red.
• Reliez l'appareil-photo de réseau au câble
de réseau.
• Schließen Sie Netzkamera an Netzkabel an.
• Conecte a câmera de rede ao cabo da
rede.
• Colleghi la macchina fotografica di rete al
cavo della rete.
WAN INPUT
LAN INPUT
LAN INPUT
LAN INPUT
Connect appropriate alarm output of the camera to
the IP Reset alarm input wires. Please consult your
cameras operating instruction to insure proper
installation. Color codes for the ip reset are located
on device cover
IP RESET ALARM WIRES
IP RESET DEVICE
22
23
Replacement Parts
Liberty Series
PB26LG
DESCRIPTION
1 RP30VL3744 PB26LG POWER BOX
2
RP30VL2742 POLE MOUNT CLIPS
3 RP30VL3740 ELECTRONICS MOUNTING PLATE
4 RP70TRANS12 TRANSFORMER, 96 VA
5 RP30VL3737 SURGE BRACKET
6 RP70LF3VR3 120/240V 50-60 Hz LINE FILTER
7 RPSPPA405 15A PARALLEL SURGE PROTECTOR
8
RP110IPR01 IP RESET
9 RP76VL2007 4G POWER AND CONNECTION BOARD ASSEMBLY
10 RP70VL3727 BOARD SHIELD, LIBERTY SERIES
11 RP76RCNEX1 MOBILE ROUTER
12
13
14
15
16
17
18
PART #
RP71BLEH220 BLOWER, 115VAC 60mm
RP30VL3736 BLOWER BRACKET
RP96GK3745 MODEM LID GASKET
RP30VL3742 MODEM LID
RP94FSSR04 CABLE STRAIN RELIEF
RPPBLOCK TAMPER PROOF, LOCK, PB26
RPPB26PLUG ½” PLUG, 94-FSUP09, 94-FSRT03, 96-REORG19
Product Registration/Warranty
Thank you for choosing Moog Videolarm. We value your patronage and are solely committed to providing you with the highest
quality products available and superior customer service.
Should a problem arise, rest assured that Moog Videolarm stands behind its products by offering impressive 3 Year and 5 Year warranties, depending on the product
purchased. See full warranty details at www.moogvideolarm.com/technical-support/warranty-plan/
Register Your Products Online
Please take a few moments to register your purchase via the Online Product Registration Form at:
www.moogvideolarm.com/technical-support/product-registration
Register your recent Moog Videolarm purchase and benet from the following:
• Simple and Trouble-Free RMA process
• Receive product updates, and special promotion
• Eliminate the need to archive original purchase documents:
Receipts, Purchase Orders, etc…
/