Wet Sounds TB-MIC User guide

Type
User guide

Wet Sounds TB-MIC is a high-performance audio device designed to enhance your sound system. With its ability to connect to your existing Wet Sounds audio system, the TB-MIC lets you enjoy crystal-clear communication and control your music from the convenience of your vehicle's glove box. The TB-MIC features an easy-to-use control panel, allowing you to adjust volume levels and easily switch between audio sources. Its compact size and durable construction make it the perfect addition to any off-road adventure.

Wet Sounds TB-MIC is a high-performance audio device designed to enhance your sound system. With its ability to connect to your existing Wet Sounds audio system, the TB-MIC lets you enjoy crystal-clear communication and control your music from the convenience of your vehicle's glove box. The TB-MIC features an easy-to-use control panel, allowing you to adjust volume levels and easily switch between audio sources. Its compact size and durable construction make it the perfect addition to any off-road adventure.

High Performance Audio
TB-MIC Installation on AR-5 Ranger Crew Roof (Zone 2 Tower)
WET SOUNDS, INC.
2975 LOUISE ST ROSENBERG, TX 77471 TOLL FREE 877-938-7757 FAX 832-550-2331
v8.7.23
OFF SYSTEM
POWER ON
MC-2
Zone 2 Output From
MC-2 to TB-MIC Input
2x 25’ AUX Cable to
run to the Glove Box
for Mic/Lvl Control
TB-MIC
RCA from Secondary
Tower Amp will go to
Output on TB-MIC
Power/Ground to Fuse Box.
Tap Blue Trigger Wire into Blue
Amp On Wire on MC-2 Plug
Pin #7 Amp-On
WS-TB-MIC
ROUTE FOR
AUX CABLES
High Performance Audio
TB-MIC Installation on AR-5 Ranger Crew Roof (Zone 2 Tower)
WET SOUNDS, INC.
2975 LOUISE ST ROSENBERG, TX 77471 TOLL FREE 877-938-7757 FAX 832-550-2331
v8.7.23
You will need to
remove 4 Allen
screws to gain
access behind
the radio. You will
have room on
both sides of the
MC-2.
Wipe area with
alcohol let dry then
apply double side
tape to the Talk
Back Mic. mount
the unit on the
left-hand side add
some foam pad-
ding to prevent
rattle.
Once you have the
box secured then
time to wire into the
MC-2’s harness. Wire
up Blue to Blue and
then extend your
power and ground to
go towards the back
with the Aux Cables.
The Fuse box is in
the same area as
the secondary amp.
There is a 12v output
location available.
remove cover and
place a 2amp fuse in
the empty location.
And connect your
red wire from the talk
back mic and ground
at any ground post.
In order to reach
the glove box area
or just anywhere up
front you will need
to purchase two 25ft
Aux Cables to make
the run.
High Performance Audio
TB-MIC Installation on AR-5 Ranger Crew Roof (Zone 2 Tower)
WET SOUNDS, INC.
2975 LOUISE ST ROSENBERG, TX 77471 TOLL FREE 877-938-7757 FAX 832-550-2331
v8.7.23
With the amp out you
will pull the grommet
out some and will
need to cut the elec-
trical tape in order to
slide the cables into
the main harness of
the roof. You will tuck
the cables in till you
get down to the area
were its connected
to the battery.
Wrapp the aux cables in
tesa tape to make the
run easier. There are a
few tabs you will need
to remove from the
cupholder panel. This
will allow you to run the
cables up front following
OEM wires.
The center
switch panel will
need to be re-
moved to gain
access to the
glove box.
Now the front cup hold-
er/center console needs
to be removed same
process as the rear one.
There is an OEM harness
that you can zip tie and
run the cables along
side it.
Lift passenger sear and
remove tray to gain
access and pull the AUX
cable from the back.
Once the rear center
console is removed
you can run the Aux
cables along side OEM
wire.
Plug in your 3.5 Aux
cables and tape/heat
shrink and rout them
towards the back of the
roof with a Long zip Tie or
a wire grabber. removing
the Secondary amp will
make things easier to sh
the cables through.
High Performance Audio
TB-MIC Installation on AR-5 Ranger Crew Roof (Zone 2 Tower)
WET SOUNDS, INC.
2975 LOUISE ST ROSENBERG, TX 77471 TOLL FREE 877-938-7757 FAX 832-550-2331
v8.7.23
Under the switch
panel you will lo-
cate 2 tabs to be
removed.
Route your cable along
side of OEM harness and
up into the dash area. In
order to make your way
to the glove box. Any
access wire you can tie
up in this area.
The male Aux will go to
the controller and the
female Aux will go to the
Mic. The Mic will reach
to the driver area and
can still close the glove
box. We recommend
this location to prevent
loss or damage when
not in use.
Mount the control
just shy of the glove
box you can and
pop 2 holes big
enough for the AUX
cable to t through.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Wet Sounds TB-MIC User guide

Type
User guide

Wet Sounds TB-MIC is a high-performance audio device designed to enhance your sound system. With its ability to connect to your existing Wet Sounds audio system, the TB-MIC lets you enjoy crystal-clear communication and control your music from the convenience of your vehicle's glove box. The TB-MIC features an easy-to-use control panel, allowing you to adjust volume levels and easily switch between audio sources. Its compact size and durable construction make it the perfect addition to any off-road adventure.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI