Jiangsu Tech Leading Information Technology EW-BLED-26 User manual

Brand
Jiangsu Tech Leading Information Technology
Model
EW-BLED-26
Type
User manual
Jiaxing Tech-leading information technology Co., Ltd.
EW-BLED-26
Bluetooth module
V1.0
20201208 1
Jiaxing Tech-leading information technology Co., Ltd.
Rev.
Information
management
About this Manual
<<EW‐BLED‐26ModuleSpecifications>>providesanintroductiontothebasicfunctionsofthe
EW‐BLED‐26module,includingitselectricalspecifications,RADIOfrequencyperformance,pinsize,and
referenceschematicdesign.Readerscanrefertothisdocumentforadetailedunderstandingofthe
overallfunctionalparametersofthemodule.
Revision history
2
Rev No.
Date Update history Editor
V1.02020.12.08Initial release Jon
Jiaxing Tech-leading information technology Co., Ltd.
Contents
About this manual......................................................................................................2
Revision history...........................................................................................................2
Contents.......................................................................................................................3
1. Profile...............................................................................................................................4
1.1
Features...............................................................................................................4
1.2
Application scope.................................................................................................5
2. Electrical specification...................................................................................................6
3. Pins explanation..............................................................................................................7
3.1
Pins layout.............................................................................................................8
3.2
Pins definition.......................................................................................................8
4. Design reference..............................................................................................................9
4.1Reference schematic...............................................................................................9
4.2Module dimension................................................................................................10
4.3  Attention................................................................................................................11
4.4
Reference PCB package........................................................................................12
5. Reflow parameter recommendation................................................................................13
3
Jiaxing Tech-leading information technology Co., Ltd.
1.Profile
1.1Features
EW‐BLED‐26isasmallandlow‐costBTandBLE5.0dual‐modeBluetoothmoduledevelopedby
JiangsuTech‐leadingCo.,Ltd.
Thefeaturesofthismoduleareasfollows：
protocol
Built‐inhighperformanceRISC32‐bitCPU,160MHzmainfrequency,512KBFlash,128KBRAM
MeetBluetooth5.0standard,support1Mbps,500Kbps,125Kbpsrate
Transmittingpower:BLE:4.82dBm; BR(GFSK):0.24dBm; EDR(π/4-DQPSK):1.02dBm .
Receivingsensitivity:Thereceivingsensitivityreaches‐94dBmin125Kbpsmode
SupportUSB,UART,ADC,SPI,PWMandotherinterfaces
SupportFTMSprotocol,canbecustomizedaccordingtothecustomercommunication
Supporttruerandomnumbergenerator
SupportBTclassicBluetoothandBLEdataBluetoothdual‐modeoperation
On‐boardhighperformancePCBantenna
Stampholepin,easyandreliablewelding
Ultra‐smallpackage：11.2x16mm
Ultra‐widesupplyvoltage：2.2V-5.5V
Working temperature：-20℃ ~ + 70℃
4
Jiaxing Tech-leading information technology Co., Ltd.
TheEW‐BLED‐26moduleneedstoconnectthefourlinesofVCC,GND,TXandRXto
completethedatatransmissionandcommunicationfunction,andcancustomizethe
specificcommunicationprotocolandcustomizationfunctionunderthespecificapplication
environmentaccordingtotheneedsofcustomers.Afterthemoduleisconfigured,youcan
userelevanthandsoftwaretotestthecommunicationdatafunction.Userscanconduct
Bluetoothconnectionandcommunicationtestthroughthecommonlyusedmobile
Bluetoothcommunicationtesttool.BTaudiotransmissioncanbedirectlyconnectedtothe
twochannelsofDACRandLofthetestmodulethroughthemobileBluetoothforaudio
signaloutput.
Tech‐leadingcompanyhasbeenengagedinthefieldofBluetoothformanyyears,and
hasstrongresearchanddevelopmentstrength.Itcaneasilyrealizetheinterconnection,
datatransmissionandothervariousapplicationsofusers'Bluetoothdevices.Ourcompany
cancustomizeanddesigntheBluetoothmoduleaccordingtocustomers'requirements
basedontheEW‐BLED‐26dualmodeBluetoothmoduleandprovidecorresponding
softwareandhardwaresupport.
1.2ApplicationScope
IoT devices; Fitnessequipment:treadmill,rhythmmachine,etc
5
Jiaxing Tech-leading information technology Co., Ltd.
AbsoluteMaximumRatings
Attention:
RecommendedOperatingConditions
PowerConsumption
2. Electricalspecifications
Theelectricalcharacteristicslistedaretargetspecificationsforreferenceonly.Someofthedata
maybeupdatedbasedonactualtestresults
ThevoltagevaluesshownarebasedonGNDinthemodule.Anyvoltageexceedingthe"maximum
rating"maycausepermanentdamagetotheequipment
5
5
Operation
Mode
Average
Maximum
Unit
TXpeekcurrent(0dB) 16mA
RXpeekcurrent 30mA
Deepsleepcurrent(include
128KretentionRAM)300μA
Poweroff10 μA
Rating
Min
Max
Unit
SupplyVoltageVCC2.25.5V
I/OVoltageALDO_OUT2.23.6V
Storage
Temperature
Tstr‐2070ºC
Item
Symbol
Min
Type.
Max
Unit
SupplyVoltageVCC2.23.35.5V
I/OVoltageALDO_OUT 2.23.33.6V
Operating
TemperatureTopr‐20‐70ºC
Jiaxing Tech-leading information technology Co., Ltd.
Audio
CODEC
6
Di
g
ital
to
Analo
g
ue
Converter(Mono)
PARAMETER
CONDITIONS MIN TYP MAX
UNIT
Resolutio
n
‐‐ ‐ 20Bits
Sam
p
lin
g
fre
uenc
Thes
y
nchronized clock 848kHz
SNR
(SignaltoNoiseRatio)
Fin=1kHz
B/W=20Hz—20KHz
A‐WeightedTHD_N<0.01%
Fs(8K,16K,32K,44.1K,48K)92dB
Di
g
italGai
n
Di
g
italGain ‐48 32dB
Analo
g
ueGainAnalo
g
Gain Resolutio
n
= 0 ‐30dB
Out
p
u
t
volta
g
eVDDA=2.9V 1500 mV
Sto
p
bandattenuation 65 dB
Analo
g
to
Di
g
ital Converter(Mono)
PARAMETER
CONDITIONS MIN TYP MAX
UNIT
Resolutio
n
‐
‐ ‐
16Bits
Sam
p
lin
g
fre
uenc
Thes
y
nchronized clock
8
48kHz
SignaltoNoiseRatio
A‐wei
g
hted 79 dBFS
W/Owei
g
htin
g
79 dBFS
Di
g
italGainDi
g
italGain ‐48 32dB
Analo
g
ueGainAnalo
g
Gain Resolutio
n
=
0
30dB
Jia
n
3.
3.
1
n
gsuTech‐
Pins
d
1
Pins
LeadingI
n
d
escri
p
distrib
Note:Fig
u
n
fotechn
o
p
tion
ution
Figu
r
u
re3‐1Pinf
u
o
logyCo.,
r
e
3-1
Modu
u
nctionalityc
a
Ltd.
le
pins
fi
g
a
nberedefi
n
g
ure
n
edbypinre
u
u
se
7
Jiaxing Tech-leading information technology Co., Ltd.
3.2
Pins definition
8
PIN
#
Pin name
Type Description
1PA4I/OPWMH1H
2USBDMI/OADC11/USBDM
3USBDPI/OUSBDP
4PA5I/OADC2
5 PA3 I/O PDC0/AUX1L/PA1
6 PA4 I/O PWM1/ADC1/AUX1R
7PA0I/O MIC
8DACRAnalogOutputDACR
9DACRAnalogOutputDACL
10PB3I/OSD0DAT/AUX2R/PWM2
11PB6I/OAUX2L
12PB2I/OSPI2DIA/UART2TXC/SPI0_CLKB
13VCC POWER
14PR2I/ORESET1/ADC12
15PR2I/ORESET2
16PB0I/OADC6/PWMH2L/TXD
17PB1I/OADC7/RXD
18GNDGNDGND of module
19 VDDIO IOPOWER VDDIO
20PB5I/OSD0CLK/AUX0R/ADC9
21PB4I/OSD0CMD/AUX0L/ADC8/PWM3
3RZHUVXSSO\2.25.5VW\SLFDOYDOXH9
Jiaxing Tech-leading information technology Co., Ltd.
4.2
 Modulesize
4‐1
Top
View
(Seen
from
Top)
Bottom
View
(Seen
from
Bottom)
4‐
2
Module thickness
Note:Tech‐Leadingcompanyreservestherighttoselectcomponentsfromdifferentsuppliers
torealizethefunctionofmodules.Allmechanical,electricalspecificationsandmodule
certificationsaremaintained.Alldimensionsareinmm(mm)
9
Jiaxing Tech-leading information technology Co., Ltd.
Table 4-3 Module design size
4.3
Attention
Bluetoothworksatthefrequencyof2.4GHz,sotheinfluenceofvariousfactorsonthe
wirelesstransceivershouldbeavoidedasfaraspossible.Pleasenotethefollowingpoints：
Avoidusingmetalaspartoftheproducthousingsurroundingthemodule.Ifthehousingis
metal,considerusinganexternalantenna
ThemetalscrewsinsidetheproductshouldbekeptawayfromtheRFpartofthemodule
TomaximizeRFperformance,theusermainboardlayoutshouldfollowthefollowing
recommendations：
Antennaclearancearea:theuser'smainboardlocateddirectlybelowthemodule
antennaareashallnothaveanycopperfoilwiring,includingpowersupply,groundand
signallayer)。
Modulelocation:Ideally,themoduleshouldbeplacedinacorneroftheuser's
motherboard.ThePCBantennaislocatedatthefarendofthemotherboard.Thisposition
minimizestheantennaclearancearea。
（Refertothefollowingfigureforthedefinitionofantennaclearancearea）
4‐
4
Antenna
Keep
out
10
Module profile size /HQJWK;PP
:LGWK<PP
Antenna location size /HQJWK;PP
:LGWK<PP
PCB thickness +HLJKW+PP
Total
module
thickness
(PCB
thicknes
s
maximum component height)
+HLJKW+PPW\SLFDO
Jiaxing Tech-leading information technology Co., Ltd.
4.4
Reference PCB packaging
4‐
5
Reference packaging size
11
Jiaxing Tech-leading information technology Co., Ltd.
5.
Reflow parameter recommendation
The reflow parameters can be set as follows：
Figure5‐1Recommendedreflowcurv
Table5‐1Recommendedparametersforreflow
12
7HPSHUDWXUHUDQJH7LPH.H\SDUDPHWHUV
3UHKHDW]RQH℃6 5DPSXSUDWH≤6
8QLIRUPWHPSHUDWXUH]RQH℃6 5DPSXSUDWH6
5HFLUFXODWLRQ]RQH!℃6 3HDN℃
&RROLQJ]RQH5DPSGRZQUDWH℃V≤6ORSH≤℃V
FCC Statement：
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference,and (2) this device must accept any
interference received, including interference that may cause undesired operation.
OEM Guidance
1. Applicable FCC rules
This module is granted by Single Modular Approval. It complies to the
requirements of FCC part 15C, section 15.247 rules.
2. The specific operational use conditions
This module can be used in IoT devices. The input voltage to the module is nominally 3.3V DC. The
operational ambient temperature of the module is -20 to 70 degree C. Only the embedded PCB
antenna is allowed. Any other external antenna is prohibited.
3. Limited module procedures
N/A
4. Trace antenna design
N/A
5. RF exposure considerations
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment can operated with minimum distance 5mm between the radiator and your body.
6. Antenna
Antenna type: PCB antenna; Antenna Gain: 0 dBi
7. Label and compliance information
An exterior label on OEM’s end product can use wording such as the
following: “Contains Transmitter Module FCC ID: 2AXDJ-EW-BLED-26”
or “Contains FCC ID: 2AXDJ-EW-BLED-26”
8. Information on test modes and additional testing requirements
a)The modular transmitter has been fully tested by the module grantee on the required
number of channels,modulation types, and modes, it should not be necessary for the host
installer to re-test all the available transmitter modes or settings. It is recommended that the
host product manufacturer, installing the modular transmitter,perform some investigative
measurements to confirm that the resulting composite system does not exceed the spurious
emissions limits or band edge limits (e.g., where a different antenna may be causing
additional emissions).
b)The testing should check for emissions that may occur due to the intermixing of emissions
with the other transmitters, digital circuitry, or due to physical properties of the host product
(enclosure). This investigation is especially important when integrating multiple modular
transmitters where the certification is based on testing each of them in a stand-alone
configuration. It is important to note that host product manufacturers should not assume that
because the modular transmitter is certified that they do not have any responsibility for final
product compliance.
c)If the investigation indicates a compliance concern the host product manufacturer is
obligated to mitigate the issue. Host products using a modular transmitter are subject to all
the applicable individual technical rules as well as to the general conditions of operation in
Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of the host product
will be obligated to stop operating the device until the interference have been corrected .
9. Additional testing, Part 15 Sub part B disclaimer The final host / module combination
need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order
to be properly authorized for operation as a Part 15 digital device.
The host integrator installing this module into their product must ensure that the final
composite product complies with the FCC requirements by a technical assessment or
evaluation to the FCC rules, including the transmitter operation and should refer to guidance
in KDB 996369. For host products with certified modular transmitter, the frequency range of
investigation of the composite system is specified by rule in Sections 15.33(a)(1) through
(a)(3), or the range applicable to the digital device, as shown in Section 15.33(b)(1),
whichever is the higher frequency range of investigation When testing the host product, all
the transmitters must be operating.The transmitters can be enabled by using publicly-
available drivers and turned on, so the transmitters are active. In certain conditions it might
be appropriate to use a technology-specific call box (test set) where accessory 50 devices or
drivers are not available. When testing for emissions from the unintentional radiator, the
transmitter shall be placed in the receive mode or idle mode, if possible. If receive mode only
is not possible then, the radio shall be passive (preferred) and/or active scanning. In these
cases, this would need to enable activity on the communication BUS (i.e., PCIe, SDIO, USB)
to ensure the unintentional radiator circuitry is enabled. Testing laboratories may need to add
attenuation or filters depending on the signal strength of any active beacons (if applicable)
from the enabled radio(s). See ANSI C63.4, ANSI C63.10 and ANSI C63.26 for further
general testing details.
The product under test is set into a link/association with a partnering device, as per the
normal intended use of the product. To ease testing, the product under test is set to transmit
at a high duty cycle, such as by sending a file or streaming some media content.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15

Jiangsu Tech Leading Information Technology EW-BLED-26 User manual

Brand
Jiangsu Tech Leading Information Technology
Model
EW-BLED-26
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents