Tecno BC1 User guide

Brand: Tecno

Model: BC1

Type: User guide

Tecno BC1: Your gateway to a world of possibilities. With its advanced features and sleek design, the Tecno BC1 offers an immersive experience like never before. Capture stunning moments with its high-resolution rear camera, and enjoy crystal-clear selfies with the front camera. The powerful battery ensures long-lasting usage, while the expansive storage lets you store all your cherished memories. Stay connected with friends and family using the dual SIM capability, and navigate seamlessly with the user-friendly interface. Experience the Tecno BC1 - where technology meets elegance.

CTP

CTP glue

LCD

Upper housing

Front camera rubber

Front camera

Front camera conductive cloth

Rear camera

Receiver

Receiver conductive velvet

Rear second camera

Rear second camera rubber

Fingerprint bracket

Fingerprint

Sidekey FPC

Speaker FPC

Speaker

Main board

Receiver FPC

Sub board

Motor

USB rubber

Rear housing A part

Rear housing B part

Rear camera lens

Battery

Battery steel

Battery cover

Know your phone

1.Status LED

2.Front camera

3.Front flash

4.Volume key

5.Power key

①

SIM/SD card installation

1. Power off mobile.

2. Refer to the following picture for SIM / SD card installation.

You can charge your device using a charger or by connecting it

to the computer using a USB cable (comes with the phone).

1. Please remind the front and back of the plug.

2. Use only TECNO charger and cables. Other chargers or cables

may damage the device. This will invalidate your phone

warranty.

FCC Statement

1.This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including

interference that may cause undesired operation.

2.Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in

a residential installation.

This equipment generates uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.`

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

SAR Information Statement

Your wireless phone is a radio transmitter and receiver. It is designed and

manufactured not to exceed the emission limits for exposure to

radiofrequency (RF) energy set by the Federal Communications

Commission of the U.S. Government. These limits are part of

comprehensive guidelines and establish permitted levels of RF energy for

the general population. The guidelines are based on standards that were

developed by independent scientific organizations through periodic and

thorough evaluation of scientific studies. The standards include a

substantial safety margin designed to assure the safety of all persons,

regardless of age and health. The exposure standard for wireless mobile

phones employs a unit of measurement known as the Specific Absorption

Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. * Tests for SAR are

conducted with the phone transmitting at its highest certified power level

in all tested frequency bands. Although the SAR is determined at the

highest certified power level, the actual SAR level of the phone while

operating can be well below the maximum value. This is because the phone

is designed to operate at multiple power levels so as to use only the power

required to reach the network. In general, the closer you are to a wireless

base station antenna, the lower the power output. Before a phone model is

available for sale to the public, it must be tested and certified to the FCC

that it does not exceed the limit established by the government adopted

requirement for safe exposure. The tests are performed in positions and

locations (e.g., at the ear and worn on the body) as required by the FCC for

each model. The highest SAR value for this model phone when tested for

use at the ear is 1.194W/Kg and when worn on the body, as described in

this user guide, is 0.498W/Kg(Body-worn measurements differ among

phone models, depending upon available accessories and FCC

requirements). The maximum scaled SAR in hotspot mode is 1.322W/Kg.

While there may be differences between the SAR levels of various phones

and at various positions, they all meet the government requirement for

safe exposure. The FCC has granted an Equipment Authorization for this

model phone with all reported SAR levels evaluated as in compliance with

the FCC RFexposure guidelines. SAR information on this model phone is on

file with the FCC and can be found under the Display Grant section of

http://www.fcc.gov/ oet/fccid after searching on

FCC ID: 2ADYY-BC1 Additional information on Specific Absorption Rates

(SAR) can be found on the Cellular Telecommunications Industry

Asso-ciation (CTIA) web-site at http://www.wow-com.com. * In the United

States and Canada, the SAR limit for mobile phones used by the public is

1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard

incorporates a sub-stantial margin of safety to give additional protection

for the public and to account for any variations in measurements.

Body-worn Operation

This device was tested for typical body-worn operations. To comply with RF

exposure requirements, a minimum separation distance

of 10mm must be maintained between the user’s body and the handset,

including the antenna. Third-party belt-clips, holsters,

and similar accessories used by this device should not contain any metallic

components. Body-worn accessories that do not meet these requirements

may not comply with RF exposure requirements and should be avoided.

Use only the supplied or an approved

Tecno BC1 User guide

Tecno BC1 User guide

Related papers