CONTENTS
•
Warnings ................................................................ 1-4
•
Assembly ................................................................ 6-7
•
Operation ................................................................8-9
•
Maintenance & Storage ................................... ...... 10
•
Trouble Shooting .................................................... 11-12
•
Warranty Information ............................................... 13
•
Diagram ................................................................... 5
Page 1 of
13
Warnings
●
If the propane gas tank is leaking gas,
you may hear, see, or smell a hiss. Do
the following:
1. Disconnect the propane gas tank.
2. Do not attempt to fix the problem by
yourself.
3. Move yourself and all persons away
from the immediate area.
●
Do not use a flame to check for gas
leaks.
●
Keep gas tank at least 5 ft away from
unit when lit. (if external tank)
●
The maximum gas supply pressure is
250 psi
WARNING
●
Improper installation,
adjustment, alteration, service or
maintenance can cause injury or
property damage.
●
Read the owners manual
thoroughly before installing or
servicing this equipment. If the
information in this manual is not
followed exactly, a fire or
explosion may result causing
property damage, personal
injury, or loss of life.
WARNING
CARBON MONOXIDE HAZARD
●
This appliance can produce carbon
monoxide which has no odor. Using it in
an enclosed space can kill you.
●
For outdoor use only.
●
Never use in the unventilated or
enclosed areas.
DANGER
IF YOU SMELL GAS:
●
Shut off gas to the appliance.
●
Extinguish any open flame.
●
If odor continues, keep away from
the appliance and immediately call
your gas supplier or fire department
for help.
●
WARNING indicates an
imminently hazardous situation
which, if not avoided, will result
in death or serious injury.
●
Do not store or use gasoline
or other flammable vapors and
liquids in the vicinity of this or
any other appliance. An LP-
cylinder not connected for use
shall not be stored in the
vicinity of this or any other
appliance.
WARNING
Page 2 of
13
WARNING
●
Applying too much propane may result in gas pooling and will not burn.
Allow fresh air into the unit so that the remaining gas may escape.
●
Use LP propane tanks with the following dimensions: diameter 12inch,
height 18inch, capacity 20lbs.
●
You must use a propane tank that has a collar to protect the gas valve.
●
DO NOT fill tank over 80 Percent full.
●
The LP gas tank must have a listed overfilling prevention device and a
QCCI or Type I, (CGA810) LP gas tank connection.
●
The gas supply tank should be constructed and marked with the
specifications for the LP gas tanks of the U.S. Department of Transportation
or the National Standard of Canada CAN/CSA-B339, LP gas tanks, spheres
and tubes for Transportation of Dangerous Goods and Commission.
●
Discontinue use if any part of the propane tank is damaged. Rust and
dents may be hazardous and should be inspected by a gas supplier.
●
The installation of this unit must adhere to local codes or either the
National Fuel Gas Code, ANSI Z223. 1/NFPA54, OR CAN/CGA- B149.1,
National Gas and Propane Installation Code.
●
This unit is to be used with propane gas only! (sold separately), is
not intended for natural gas.
●
Do not use any solid fuel or charcoal for this unit.
●
Do not use any more than 1/4in depth lava rocks/ pumice stones/
Lava Glass above the burner holes. Doing so will suffocate the flame.
WARNING
Warnings
Page 3 of
13
WARNING
● Never place hands or fingers onto upper portion of this unit while in use.
● Keep all electrical cords and fuel supply hose away from heated surfaces.
●Combustible material should Not be within 72 inches of the top of the
unit,and within 48 inches around the entire unit. Combustible materials
could be and are not limited to any items that may catch fire such as dry
vegetation,wood,branches,leaves,plants,buildings,structures,fabrics,clothing,
sawdust,all chemicals,and all flammable liquids. Do not paint or color any
part of this Fire Table.
● Do not operate on a boat or vehicle.
●This unit can only be used on any stationary outdoor flat surface ONLY.
●All Fire Burner to cool down completely before placing lid.
●Do not store a spare Propane Gas Tank on or near this unit.
●Check for leaks after not using the unit for long periods of time.
●
The tank system must be set up for vapor with drawal.
●
Keep away from the unit for the first 20 minutes after igniting your
unit for the first time,as pumice stones/fire glass could pop out and
cause injury.Should any rocks pop out,discard them.
●
Always ensure that lava rocks/pumice stones/fire glass are
completely dry before use.
●
Do not paint or color any part of this Fire Table.
●
Do not sit or rest hands or feet on this Fire Table.
WARNING
Warnings
Page 4 of
13
WARNING
●
Do not operate unit until all parts are fully assembled.
●
Do not attempt to move it while in use.
●
This unit is not intended for cooking.
●
Young children must never operate this fire table.They should be
carefully supervised AT ALL TIMES while near the area of the
appliance.
●
Do not hang clothing or any other flammable materials from the
fire pit, or place on or near the fire pit.
●
Do not set the protective cover over the unit until it is turned
off and completely cooled down.
●
Combustible material should not be within 72 inches of the top of
the unit, or within 48 inches around the entire unit.
●
If the flame goes out while burning, turn the gas valve off. Wait 5
minutes before repeating the initial lighting procedure. Once you
have a flame started, hold down the control knob for 1 minute.
●
Inspect all elements of this heating unit before each use. If there is
damage, the burner must be replaced.
●
Keep the hose out from any pathways to eliminate any accidental
damage. (if external tank)
●
Installation and repair should be done by a qualified service person.
The appliance should be inspected before use and at least annually by a
qualified service person. More frequent cleaning may be required as
necessary.
●
You must follow all steps to properly assemble this heating item. Make
sure the gas valve is turned “OFF” before assembling. Do NOT attempt
to assemble without proper tools.
WARNING
Warnings
Page 5 of
13
Parts Diagram & List
*XDUG
,JQLWLRQ 3LQ
/DYD5RFN
1R]]OH
,JQLWHU
:LQJ6FUew with Nut
$$ Battery
,WHP3LFWXUH'HVFULSWLRQ 4W\
7KHUPRFRXSOH
*URXQG :LUH
%XUQHU3ODWH
0DLQ)UDPHRI Fire Table
&RUUXJDWHG 3LSH
6ZLWFKLQJ 9DOYH
5HJXODWRU9DOYH
ZLWK*DV+RVH
&RQWURO.QRE
0HWDO6WDQG for Propane
Tank (Optional)
Burner
1
Page 6 of
13
Step 1:
Check that the control knob (13) for the gas
supply system is turned to the “OFF”
position before starting any assembly.
Step 2:
Place a 20 lbs Propane Gas Tank (not
included) into a secure position.Put it into the
tank holder (16).Turn the wing screw on the
outside of the tank holder (16) clockwise to
tighten the tank into the tank holder.
DANGER
Propane tank must be a minimum of 60
inches away at all times.
Step 3:
Turn the cylinder valve (21) on the tank
clockwise direction to TURN OFF SUPPLY of
the LP Gas supply-Attach the pressembled
Regulator(12/19) from the Fire Table to the
Cylinder Value(21) by turning the Black
Regulator Coupling Nut(20) clockwise.
Make sure it is fastened securely and tighten
connections-by HAND only.
Assembly Instructions
16
13
Page 7 of
13
Step 4:
Remove the Electronic igniter Cap(14) on the
Electronic igniter (14) by unscrewing and slide
the Battery(17) into the battery slot(14).Make
sure the positive side of the Battery(17) faces
outwards.Screw the Electronic Igniter Cap(14)
over the battery,tightly.
Step 5:
Subject to your preference,you may pour
Lava Rocks over the Burner Ring.
The Guard MUST NOT BE BLOCKED.Refer to
guidance below:
Do not place more than 1/4 inch depth of lava
rocks above the burner holes.Doing so will
suffocate the flame.
Do not place more than 6.6lb of lava rocks
above the burner holes.Doing so will suffocate
the flame.
WARNING:Fire Table and LP-Cylinder must be
at a minimum of 60 inches apart.
Assembly Instructions
To ensure proper function,the
Guard (01) on the Burner (08)
should never have lava rocks
(07) covered over it.
Page 8 of
13
FOR YOUR SAFETY, READ BEFORE LIGHTING
•Before performing a leak test, make sure that no sparks can occur and you
are in a spacious outdoor area.
•Connect the propane gas tank to the regulator and turn the valve on the
unit to the “off” position.
•Brush a soap and water mixture on all connections.
•Make sure the igniter battery has been installed properly. The igniter will
not operate otherwise.
•Before operating, smell around the appliance and next to the ground for
gas odors. If you smell gas or a leak is discovered,immediately turn the gas
valve off, disconnect propane gas tank and do not use the appliance until
the leak is repaired.
•After turning the gas supply, if bubbles occur on any connection there may
be a leak.
•Do not use the appliance if any part has been submerged under water.
Immediately call a qualified service technician to inspect the unit and to
replace the part.
•Do not use the heating unit without inspecting the gas hose (if applicable).
•If there are signs of wear or abrasion, please immediately replace the hose.
•Pumice stones/lava rocks/Lava Glass could pop up and strike somebody’s
face during the process of lighting this unit; stand away from the unit for
the first 20 minutes after igniting.
•Inspect the Gas Hose(12) before using the Fire Table.
•If there are signs of wear or abrasion on the hose,you must replace the
Gas Hose(12).The Gas Hose must be supplied directly by manufacturer.
•Wait 10 minutes after extinguishing flame prior to replacing a lid(if
applicable) or protective cover on to the Fire Table.
Operation
Page 9 of
13
LIGHTING INSTRUCTIONS
1. Make sure the control knob (13) is in the “off” position
2. Push and hold the electronic igniter (14) to create sparks within the
electrode, continue to hold.
3. Push in the control knob (13) and turn to the “low”
position. Keep holding the control knob (13) to allow gas to flow for
15 seconds.
4. If ignition does not occur within a few seconds release the control
knob (13) and rotate to the “off” position. Wait for 5 minutes for gas to
clear and then repeat the above lighting instructions.
5. Once the product is lit, the flame intensity may be controlled by
turning the control knob (13) between the “low” and “high” positions.
6. Observe flame height when lit:
1) Flame color should be yellow/blue.
2)Flame height burns at 2-20 inches high.
HOW TO EXTINGUISH ?
•Turn control knob (13) clockwise to the “low” position; let the
knob pop up and continue turning the control knob (13) to the
“off” position.
•Wait 5 minutes after extinguishing flame prior to placing a lid (if
applicable) or protective cover on heating item.
•Close the cylinder valve on the propane gas tank if you don’t intend
to use it for a long time.
Operation
Page 10 of
13
To enjoy years of outstanding performance from your heater, make
sure you perform the following maintenance activities on a regular
basis:
•Before performing any maintenance always disconnect propane gas
tank.
•Use warm soapy water for cleaning. Never use flammable or corrosive
cleaning agents.
•Keep the heating item free and clear from combustible materials.
•Visually inspect burner for obstructions and keep tank enclosure free
and clear from debris.
•Use a soft brush to get rid of the mild stains, loose dirt and soil after
the burner and pumice stones/lava rocks/Lava Glass completely cooled
down. Wipe down with a soft cloth.
•Harsh weather conditions may cause stubborn stains, discoloration and
possibly rust pitting.
•Permanent damage may occur if powder or solvent comes in contact
with painted or plastic components on this heating unit.
•Keep the heating unit stored away from direct sunlight.
•If storing this unit inside, disconnect the propane gas tank from the
gas valve.
•Not using manufacturer approved or supplied parts/accessories may
result in a defective condition and void the warranty of this heating
unit.
•Always place lid (if applicable) or protective cover on heating item
when not in use. Turn control knob OFF.
NOTE: In a salt-air environment (such as near to ocean),
corrosion occurs more quickly than normal. Frequently check for
corroded areas and repair them promptly.
Maintenance & Storage
Page 11 of
13
Trouble Shooting
PROBLEM SOLUTION
Electrode and burners are wet
Igniter battery is dead or
backwards
Igniter Pin cracked or broken
-sparks a crack
Wipe dry with cloth.
Check that the battery is inserted correctly in
the igniter or replace the battery.Make sure the
plastic wrap on the battery has been removed.
Please contact us to request the parts.
Residue on Igniter Pin
No Gas Flow
Check for residue on the igniter pin or
Thermocouple. If dirty,thoroughly clean the area.
Check that the electronic Ignitor Cap is tightly
fitted to the spring.If loose,please adjust the
spring accordingly.
Check if the LP gas tank is empty. If empty,
replace and refill. If the propane tank is not empty,
refer to Problem: Sudden drop in gas flow on the
following page.
Coupling nut and regulator not
fully connected
Turn the coupling nut about one half to three
fourths a turn, until you feel a solid stop. Do not
use tools, tighten by hand only.
Obstruction of gas flow Check for bent or kinked hose.
Spider webs or insect nest in
the venturi Clean the venturi.
Burner ports clogged or
blocked
Reference Problem: Irregular flame pattern on the
following page. Clean the burner ports as
described there.
Hose from gas fire table
is pinched
Make sure the hose is not pinched between the
fire table and the source of the gas.
Flame is being obstructed at
burner ports or mixing chamber
of the burn tube is blocked or
obstructed
Make sure that the gas ports on the burner are
free of any lava rocks/fire glass so that the
flame can flow naturally.Clear out the mixing
chamber located before the Venturi.
Out of Gas Check for gas in the LP gas tank.
Excess flow safety device may
have been activated
Turn control knob to OFF, wait 30 seconds and
light outdoor fire table.if flames are still too low,
reset the excessive flow safety device by turning
off the control knob and LP gas tank valve.
Disconnect regulator. Turn burner control knob to
HIGH. Wait at least 5 minutes. Turn burner control
knob off. Reconnect regulator and perform a leak
check at tank connection. Turn LP gas tank valve
on slowly, wait 30 seconds and then light outdoor
fire table.
Irregular flame pattern, flame does
not run the full length of the burner
Burner ports are clogged or
blocked
Clean burner ports.Do this by inserting a
paperclip into each of the burner ports to
ensure they are not clogged.
WARNING: Make sure burner is not on, and
has had sufficient time to cool before touching it.
High or gusting winds Increase flame to HIGH setting.
Low on LP gas Replace or refill LP gas tank.
Excess flow valve tripped Refer to Problem: Sudden drop in gas flow.
Flame seems to lose heat when
burning in cold weather -
temperature below 50°F
Ice has built up on the outside
of the LP gas tank because
the vaporization process is too
low
Turn the control knob and the LP gas tank to OFF.
Replace with a spare LP gas tank and resume
burning. Store the spare LP gas tank in a well
ventilated area, away from children.
Burner will not light using igniter
Burner will not light with match
The fire table emits a lot of
black smoke when in use
Sudden drop in gas flow, or a
reduced flame height
Flame blow out
CAUSE
AA
Page 12 of
13
Trouble Shooting
Problem: Burner JUST LIGHT UP FOR SECOND AND WILL AUTOMATICALLY TURN OFF
PILOT
GUARD
1
3
.
4
.
THERMOCOUPLE
IGNITION
PIN
THERMOCOUPLE IGNITION
PIN
2.
1. The thermocouple will be under the Pilot Guard on the top of the unit.
Please remove the Pilot guard by unscrewing it from the metal bowl with a screw driver.
2. Once the Pilot Guard has been removed, you will have two components exposed; the copper one is your
thermocouple. Please unscrew the nut holding the thermocouple in place.
3.
Inside the unit, you will notice that the end of the thermocouple line is directly screwed to the gas valve. Please unscrew
the thermocouple from the back end of the gas valve. Do not take off the valve’s silver backing, only unscrew the small
nut as shown above.
4.Screw the end of the thermocouple to the back end of the gas valve with the silver backing.
Once this has been done, please test the unit. You may have to reset the gas valve once again as the safety mechanism may
have been set off by the new components introduced:
Resetting Your Gas Valve
Completely detach the propane tank from the table. Do not forget to turn the propane tank valve down. Turn the heat knob to
high and leave it on that setting for about two to three minutes.
propane tank and turn the propane tank’s valve a Once you have done this, please turn the knob back to off. Hook up the
quarter of a turn at a time.
NOTE: When reattaching the propane tank, please turn the valve to release the gas back in to the unit VERY SLOWLY. We
want the unit to register gas coming through but not too much at once, this will flood the unit and you will have to start all
over!
This is so that the gas valve can register the gas coming through a little at a time. Once you have turned the gas on all the
way please go ahead and try to light the table again. This should reset your fire table’s safety mechanism
Page 13 of
13
This product has been manufactured under the highest standards of
quality and workmanship.
We warrant to the original consumer that all aspects of this product will
be free of defects in material and workmanship for one year from the
date of purchase. A replacement for any defective part will be supplied
free of charge for installation by the consumer. Defects or damage
caused by the use of other than genuine parts are not covered under
this warranty.
This warranty shall be effective from the date of purchase as shown in
the purchase receipt.
The manufacturer warranty will be voided by,
and manufacturer disclaims any responsibility
for, the following actions but not limited:
•Modification of the unit and/or components including the gas
valve assembly.
•Use of any component part not manufactured or approved by
us.
•Use and installation other than what is listed in this manual.
Warranty Information
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
EcoSmart PHFT30S User manual
- Type
- User manual
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Other documents
-
Topcraft ZQ-W85340126 User manual
-
Sunnydaze Decor WAR-986 Owner's manual
-
Sunnydaze Decor WAR-840 Operating instructions
-
Costway NP10261CF User manual
-
Sego Lily SL-SS4FT-13-GRY-K Installation guide
-
Table Fire 50857N Owner's manual
-
SereneLife SLFPS3 Owner's manual
-
SereneLife SLFPTL.3 User manual
-
Hanover NAPLES1PCFP User manual
-
ROOMS TO GO 79200300 Assembly Instructions
