Pioneer DEH-P6100BT - Radio / CD User manual

Pioneer
Brand
Pioneer
Model
DEH-P6100BT - Radio / CD
Type
User manual

This manual is also suitable for

ORDER NO.
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A.
PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium
PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
PIONEER CORPORATION 2009
DEH-P610BT/XS/UC
CRT4305
CD RECEIVER
DEH-P610BT
/XS/UC
DEH-P6100BT
/XS/UC
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3240 CRT4050
S10.5COMP2-iPod/USB
CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
For details, refer to "Important Check Points for Good Servicing".
K-ZZZ. MAR. 2009 Printed in Japan
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
2
1234
1234
C
D
F
A
B
E
SAFETY INFORMATION
CAUTION
Where in a manufacturer’s service documentation, for example in circuit diagrams or lists
of components, a symbol is used to indicate that a specific component shall be replaced only
by the component specified in that documentation for safety reasons, the following symbol shall
be used:
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
CAUTION:
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
- Safety Precautions for those who Service this Unit.
When checking or adjusting the emitting power of the laser diode exercise caution in order to get safe, reliable
results.
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
CAUTION
CLASS 1M INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS
2. During repair or tests, do not view laser beam for 10 seconds or longer.
WARNING
This product may contain a chemical known to the State of California to cause cancer, or birth defects or
other reproductive harm.
Health & Safety Code Section 25249.6 - Proposition 65
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
3
5678
56
7
8
C
D
F
A
B
E
[Important Check Points for Good Servicing]
In this manual, procedures that must be performed during repairs are marked with the below symbol.
Please be sure to confirm and follow these procedures.
1. Product safety
Please conform to product regulations (such as safety and radiation regulations), and maintain a safe servicing environment by
following the safety instructions described in this manual.
1 Use specified parts for repair.
Use genuine parts. Be sure to use important parts for safety.
2 Do not perform modifications without proper instructions.
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
3 Make sure the soldering of repaired locations is properly performed.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
4 Make sure the screws are tightly fastened.
Please be sure that all screws are fastened, and that there are no loose screws.
5 Make sure each connectors are correctly inserted.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc.
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
9 There should be no spark traces or similar marks on the power plug.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
a Safe environment should be secured during servicing.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
3. Lubricants, Glues, and Replacement parts
Use grease and adhesives that are equal to the specified substance.
Make sure the proper amount is applied.
5. Shipping mode and Shipping screws
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be
installed before shipment. Please be sure to follow this method especially if it is specified in this manual.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
4
1234
1234
C
D
F
A
B
E
CONTENTS
SAFETY INFORMATION..................................................................................................................................... 2
1. SERVICE PRECAUTIONS............................................................................................................................... 5
1.1 SERVICE PRECAUTIONS ........................................................................................................................ 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 5
2. SPECIFICATIONS............................................................................................................................................ 6
2.1 SPECIFICATIONS ..................................................................................................................................... 6
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 7
2.3 PANEL FACILITIES.................................................................................................................................... 8
2.4 CONNECTION DIAGRAM ....................................................................................................................... 12
3. BASIC ITEMS FOR SERVICE........................................................................................................................ 14
3.1 CHECK POINTS AFTER SERVICING..................................................................................................... 14
3.2 PCB LOCATIONS .................................................................................................................................... 14
3.3 JIGS LIST ................................................................................................................................................ 15
3.4 CLEANING............................................................................................................................................... 15
4. BLOCK DIAGRAM.......................................................................................................................................... 16
5. DIAGNOSIS.................................................................................................................................................... 19
5.1 OPERATIONAL FLOWCHART................................................................................................................ 19
5.2 ERROR CODE LIST................................................................................................................................ 20
5.3 CONNECTOR FUNCTION DESCRIPTION............................................................................................. 23
6. SERVICE MODE ............................................................................................................................................ 24
6.1 DISPLAY TEST MODE ............................................................................................................................ 24
6.2 CD TEST MODE...................................................................................................................................... 25
7. DISASSEMBLY .............................................................................................................................................. 26
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 30
8.1 CD ADJUSTMENT................................................................................................................................... 30
8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 31
8.3 PCL OUTPUT CONFIRMATION.............................................................................................................. 33
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 34
9.1 PACKING ................................................................................................................................................. 34
9.2 EXTERIOR(1) .......................................................................................................................................... 36
9.3 EXTERIOR(2) .......................................................................................................................................... 38
9.4 CD MECHANISM MODULE..................................................................................................................... 40
10. SCHEMATIC DIAGRAM............................................................................................................................... 42
10.1 TUNER AMP ASSY(GUIDE PAGE)....................................................................................................... 42
10.2 KEYBOARD UNIT.................................................................................................................................. 48
10.3 CD MECHANISM MODULE(GUIDE PAGE).......................................................................................... 50
10.4 ANTENNA UNIT .................................................................................................................................... 56
10.5 WAVEFORMS........................................................................................................................................ 57
11. PCB CONNECTION DIAGRAM.................................................................................................................... 60
11.1 TUNER AMP ASSY................................................................................................................................ 60
11.2 KEYBOARD UNIT.................................................................................................................................. 64
11.3 CD CORE UNIT(S10.5COMP2-iPod-C3)............................................................................................... 66
11.4 ANTENNA UNIT..................................................................................................................................... 68
12. ELECTRICAL PARTS LIST .......................................................................................................................... 69
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
5
5678
56
7
8
C
D
F
A
B
E
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
1.2 NOTES ON SOLDERING
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.
5. Be careful in handling ICs. Some ICs such as MOS
type are so fragile that they can be damaged by
electrostatic induction.
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
The following lead-free solders are available as service parts:
Parts numbers of lead-free solder:
GYP1006 1.0 in dia.
GYP1007 0.6 in dia.
GYP1008 0.3 in dia.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
6
1234
1234
C
D
F
A
B
E
2. SPECIFICATIONS
2.1 SPECIFICATIONS
Dimensions (W × H × D):
DIN
Chassis.................. 178 mm × 50 mm × 162
mm
(7 in. × 2 in. × 6-3/8 in.)
Nose....................... 188 mm × 58 mm × 24 mm
(7-3/8 in.× 2-1/4 in.× 1 in.)
D
Chassis.................. 178 mm × 50 mm × 162
mm
(7 in.× 2 in.× 6-3/8 in.)
Nose....................... 170 mm × 46 mm × 24 mm
(6-3/4 in.× 1-3/4 in.× 1 in.)
Weight .................................... 1.3 kg (2.9 lbs)
Audio
Maximum power output ...... 50 W × 4
50 W × 2/4
+ 70 W × 1/2
(for subwoofer)
Continuous power output .. 22 W × 4 (50 Hz to 15 000
Hz, 5 % THD, 4
load, both
channels driven)
Load impedance ................... 4
to 8 ×4
4
to 8 ×2+2 ×1
Preout max output level ...... 4 V
Equalizer (3-Band Parametric Equalizer):
Low
Frequency.............. 40/80/100/160 Hz
Q Factor ................. 0.35/0.59/0.95/1.15 (+6 dB
when boosted)
Gain......................... ±12 dB
Mid
Frequency.............. 200/500/1k/2k Hz
Q Factor ................. 0.35/0.59/0.95/1.15 (+6 dB
when boosted)
Gain......................... ±12 dB
High
Frequency.............. 3.15k/8k/10k/12.5k Hz
Q Factor ................. 0.35/0.59/0.95/1.15 (+6 dB
when boosted)
Gain......................... ±12 dB
HPF:
Frequency....................... 50/63/80/100/125 Hz
Slope............................... –12 dB/oct
Subwoofer (mono):
Frequency....................... 50/63/80/100/125 Hz
Slope................................–18 dB/oct
Gain.................................. +6 dB to – 24 dB
Phase .............................. Normal/Reverse
Bass boost:
Gain................................. +12 dB to 0 dB
CD player
System..................................... Compact disc audio system
Usable discs .......................... Compact disc
Signal-to-noise ratio............. 94 dB (1 kHz) (IHF-A net-
work)
Number of channels ............ 2 (stereo)
MP3 decoding format .......... MPEG-1 & 2 Audio Layer 3
WMA decoding format ........ Ver. 7,7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format...........MPEG-4 AAC (iTunes en-
coded only) (.m4a)
(Ver. 7.7 and earlier)
WAV signal format ................ Linear PCM & MS ADPCM
(Non-compressed)
USB
USB standard specification
............................................... USB 2.0 full speed
Maximum current supply .... 500 mA
Minimum memory capacity
............................................... 256 MB
USB Class............................... MSC(Mass Storage Class)
File system.............................. FAT16, FAT32
MP3 decoding format .......... MPEG-1 & 2 Audio Layer 3
WMA decoding format ........ Ver. 7,7.1, 8, 9, 10, 11 (2ch
audio)
(Windows Media Player)
AAC decoding format...........MPEG-4 AAC (iTunes en-
coded only) (.m4a)
(Ver. 7.7 and earlier)
WAV signal format ................ Linear PCM & MS ADPCM
(Non-compressed)
FM tuner
Frequency range................... 87.9 MHz to 107.9 MHz
Usable sensitivity.................. 9 dBf (0.8 μV/75
, mono,
S/N: 30 dB)
Signal-to-noise ratio............. 72 dB (IHF-A network)
AM tuner
Frequency range................... 530 kHz to 1 710 kHz (10
kHz)
Usable sensitivity.................. 25 μV (S/N: 20 dB)
Signal-to-noise ratio............. 62 dB (IHF-A network)
General
Power source..........................14.4 V DC (10.8 V to 15.1 V
allowable)
Grounding system................. Negative type
Max. current consumption
...............................................10.0 A
Backup current ....................... 5.0 mA or less
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
7
5678
56
7
8
C
D
F
A
B
E
2.2 DISC/CONTENT FORMAT
Bluetooth
Version..................................... Bluetooth 2.0 + EDR certi-
fied
Output power ......................... +4 dBm Max.
(Power class 2)
CEA2006 Specifications
Power output ......................... 14 W RMS × 4 Channels (4
and 1 % THD+N)
S/N ratio .................................. 91 dBA (reference: 1 W into
4
)
Note
Specifications and the design are subject to mod-
ifications without notice due to improvements.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc.
and any use of such marks by Pioneer Corporation is under license.
Other trademarks and trade names are those of their respective owners.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
8
1234
1234
C
D
F
A
B
E
2.3 PANEL FACILITIES
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
9
5678
56
7
8
C
D
F
A
B
E
e MULTI-CONTROL
Move to perform manual seek tuning, fast
forward, reverse and track search controls.
When a call comes in, press to answer the
incoming call.
Also used for controlling functions.
Turn to increase or decrease the volume.
• While using hands-free phoning, you can
select END VOLUME and switch
END VOLUME and PRIVATE in
FUNCTION by pressing
MULTI-CONTROL .
f DISP/SCRL button
Press to select different displays.
Press and hold to scroll through the text in-
formation.
g S.Rtrv/SAT MODE button
Press to switch advanced sound retriever
settings.
• When XM tuner or SIRIUS tuner is se-
lected as the source, press to change the
channel select mode.
• When SIRIUS tuner is selected as the
source, press and hold to perform the In-
stant Replay mode.
h CLOCK/DISP OFF button
Press to change to the clock display.
Press and hold to turn the display indication
and button illumination off or on.
i BAND/ESC button
Press to select among three FM bands and
one AM band.
Press to return to the ordinary display when
operating the menu.
Remote control
Operation is the same as when using the but-
tons on the head unit.
j VOLUME buttons
Press to increase or decrease the volume.
k FUNCTION button
Press to select functions.
l Thumb pad
Move to perform manual seek tuning, fast
forward, reverse and track search controls.
Also used for controlling functions.
Functions are the same as
MULTI-CONTROL except for volume con-
trol.
m DIRECT button
Press to directly select the desired track.
Press to enter a phone number while operat-
ing a phone source.
n CLEAR button
Press to cancel the input number when0 to
9 are used.
o 0 to 9 buttons
Press to directly select the desired track or
preset tuning. Buttons 1 to 6 can operate
the preset tuning for the tuner.
Press to enter a phone number while operat-
ing a phone source.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
10
1234
1234
C
D
F
A
B
E
p (off hook) button
Press to start talking on the phone while op-
erating a phone source.
q
(on hook) button
While operating the phone source, press to
end a call or reject an incoming call.
r
(mute) button
Press to turn off the sound. To turn on the
sound, press again.
s PGM button
Press to operate the preprogrammed func-
tions for each source. (Refer to Using the
PGM button.)
t AUDIO button
Press to select an audio function.
Display indication
1 Main display section
Displays band, frequency, elapsed playback
time and other settings.
• Tuner
Band and frequency are displayed.
• Built-in CD player, USB storage device,
iPod
Elapsed playback time and literal infor-
mation are displayed.
2
indicator
Appears when an upper tier of folder or
menu exists.
3
(list) indicator
Appears when operating list function.
4
indicator
Appears when a lower tier of folder or menu
exists.
5
(artist) indicator
Appears when the disc (track) artist name is
displayed on the main display section.
Appears when artist search refinement on
the iPod browsing function is in use.
6
(disc) indicator
Appears when the disc (album) name is dis-
played on the main display section.
Appears when album search refinement on
the iPod browsing function is in use.
7
(song) indicator
Appears when the track (song) name is dis-
played on the main display section.
Appears when song search refinement on
the iPod browsing function is in use.
8 LOC indicator
Appears when local seek tuning is on.
9
(stereo) indicator
Appears when the selected frequency is
being broadcast in stereo.
a
(folder repeat) indicator
Appears when folder repeat is on.
When repeat function is on, only
is dis-
played.
b
(folder random) indicator
Appears when folder random is on.
When random function is on, only
is
displayed.
c
(shuffle) indicator
Appears when shuffle function is on while
the iPod source is being selected.
d
(Sound Retriever) indicator
Appears when Sound Retriever function is
on.
For details, refer toUsing advanced sound
retriever.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
11
5678
56
7
8
C
D
F
A
B
E
e indicator
Appears whenCONTROL(control mode) is
set to IPOD.
For details about the control mode, refer to
Operating this unit’s iPod function from your
iPod.
f
(received call) indicator
Appears when received call list is displayed
while telephone source is being selected.
g
(dialled call) indicator
Appears when dialled call list is displayed
while telephone source is being selected.
h
(auto answer) indicator
Shows when the automatic answering func-
tion is on (Refer toSetting automatic an-
swering).
i
(missed call) indicator
Appears when there are missed call log.
Appears when missed call list is displayed
while telephone source is being selected.
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.
Screw
BPZ20P060FTC
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
12
1234
1234
C
D
F
A
B
E
2.4 CONNECTION DIAGRAM
When not connecting a rear speaker lead to a subwoofer
4 m (13 ft. 1 in.)
Microphone input
This product
Rear output
Front output
Antenna jack
Subwoofer output
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by
ignition switch (12 V DC).
Black (chassis ground)
Connect to a clean, paint-free metal location.
Fuse (10 A)
Fuse resister
To subwoofer
output
To front output
To rear output
IP-BUS input (Blue)
IP-BUS cable
Multi-CD player
(sold separately)
Wired remote input
Hard-wired remote control adaptor
can be connected (sold separately).
Power amp
(sold separately)
Connect with RCA cables
(sold separately)
System remote control
Power amp
(sold separately)
Power amp
(sold separately)
Microphone
Perform these connections
when using the optional
amplifier.
Blue/white
Connect to system control terminal of the power
amp or auto-antenna relay control terminal (max.
300 mA 12 V DC).
With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
thgiRtfeL
Front speakerFront speaker
Rear speakerRear speaker
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Front speaker
Front speaker
Rear speaker
Rear speaker
Subwoofer
Subwoofer
When connecting speakers without using the internal
amplifier, we recommend that this unit’s internal amp is
turned off. For more details, refer to operation manual.
DEH-P610BT/XS/UC
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
13
5678
56
7
8
C
D
F
A
B
E
When using a subwoofer without using the optional amplifier
Microphone input
4 m (13 ft. 1 in.)
Microphone
Blue/white
Connect to system control
terminal of the power amp or
auto-antenna relay control
terminal (max. 300 mA 12 V DC).
Left Right
Front speakerFront speaker
White Gray
Gray/blackWhite/black
Green Violet
Green/black Violet/black
Subwoofer (4
Subwoofer (4) )
Green Violet
Green/black Violet/black
When using a subwoofer of 70 W (2
), be sure to connect
with Violet and Violet/black leads of this unit.
Do not connect anything with Green and Green/black leads.
Subwoofer
(4
) 2
Not used.
This product
Front output
Antenna jack
Subwoofer output
Rear output
IP-BUS input (Blue)
Wired remote input
Hard-wired remote control adaptor
can be connected (sold separately).
IP-BUS cable
Multi-CD player
(sold separately)
Yellow
Connect to the constant 12 V supply terminal.
Red
Connect to terminal controlled by ignition switch (12 V DC).
Fuse (10 A)
Fuse resister
Note:
Change the initial setting of this unit.
The subwoofer output of this unit is monaural.
Black (chassis ground)
Connect to a clean, paint-free metal location.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
14
1234
1234
C
D
F
A
B
E
3. BASIC ITEMS FOR SERVICE
3.1 CHECK POINTS AFTER SERVICING
3.2 PCB LOCATIONS
To keep the product quality after servicing, please confirm following check points.
demrifnocebotmetIserudecorP.oN
1 Confirm whether the customer complain has
been solved.
If the customer complain occurs with the
specific media, use it for the operation check.
The customer complain must not be
reappeared.
Display, audio and operations must be
normal.
2 CD Play back a CD.
(Track search)
No malfunction on display, audio and
operation.
3 FM/AM tuner Check FM/AM tuner action.
(Seek, Preset)
Switch band to check both FM and AM.
Display, audio and operations must be
normal.
4 Check whether no disc is inside the product. The media used for the operating check must
be ejected.
retfaecnaraeppastinotridrosehctarcsoNkcehcecnaraeppA5
receiving it for service.
See the table below for the items to be checked regarding audio:
Item to be checked regarding audio
Distortion
Noise
Volume too low
Volume too high
Volume fluctuating
Sound interrupted
A
B
Keyboard Unit
D
Antenna Unit
CD Core Unit
(S10.5COMP2-iPod-C3)
C
Tuner Amp Assy
Unit Number : YWM5339(P610BT)
Unit Number : YWM5338(P6100BT)
Unit Name : Tuner Amp Assy
Unit Number : (P610BT)
Unit Number : (P6100BT)
Unit Name : Keyboard Unit
Unit Number : CWX3678
Unit Name : CD Core Unit(S10.5COMP2-iPod-C3)
Unit Number : YWM5398
Unit Name : Antenna Unit
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
15
5678
56
7
8
C
D
F
A
B
E
3.3 JIGS LIST
3.4 CLEANING
- Jigs List
Name
Test Disc
L.P.F.
Jig No.
TCD-782
Remarks
Checking the grating
Checking the grating (Two pieces)
Na
m
e
J
i
g
No.
R
emar
k
s
- Grease List
Name
Grease
Grease
Grease No.
GEM1024
GEM1045
Remarks
CD Mechanism Module
CD Mechanism Module
Na
m
e
G
rease No.
R
emar
k
s
Before shipping out the product, be sure to clean the
following portions by using the prescribed cleaning
tools:
Portions to be cleaned Cleaning tools
CD pickup lenses Cleaning liquid : GEM1004
Cleaning paper : GED-008
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
16
1234
1234
C
D
F
A
B
E
4. BLOCK DIAGRAM
CDL
MUTE
JA401
CN551
JA151
1
MIC1N
MICIN
MIC1PF
MICSENS
GND
KEYAD
KEYD
MIC1P
BTRX3
NRESET
BTTX3
I2C_CLK
I2C_MCLK
I2S_OUT1
I2S_SYNC
2,3
CN701
JA101
TUNER AMP ASSY
1
85
AMPMUTE
49
SYSPW
64
BTPW
87
BTSENS
A
18
19
7
1
11
7
5
8
ANTENNA
61
DDSYNC
BRST,BRXEN,BSRQ,BDATA,BSCK
VDD
ASENBO
BTMICM
TELBEE
BTRST5
BTTX5
BTRX5
CE2
SL
Lch
1
2
80
IPPW
79
RX
27
TX
28
PEE
XOUT
XIN
26
11
13
B.UP
11
9
12
CDRST
ASENB
92
VDCONT
CDRST
20
USBCTL
21
FM/AM TUNER UNIT U401
8
BUS+
BUSL+
BUSL-
IPL+
IPL-
BUS-
6
5
MECHA VDD
MECHA VD
1
3
IC701
NJM2885DL1-33
3V
→
5V
IC501
TC7SET08FUS1
5V
→
3V
Q751
Q752
Q101
A8V
Q551
B.UP
USBFLG
CDVDD
VD
DPDT
KYDT
30
29
SSENS
DSENS
71
18
38
ILMPW
SWVDD
ROT1
ILMCLR2
58
37
36
ROT0
43
BT3V
CK
DI
CE1
VCC
ROM_VDD
VDD3.3
DO
CE2
DO
DI
FM_ANT
AM_ANT
BUS+
BUS-
DIN1
ROUT
IC101
HA12241FP
STBY
WIRED
REMOTE
IP-BUS
RMIC
SYSTEM
CONTROLLER
IC601(1/2)
PEG544B8
C
OUT/IN1
OUT/IN2
2
3
2
IN/OUT1
CONT1
CONT2
BTMICMUTE
BTRX5
BTRST5
BTTX5
DACDT
DACCK
DACCS
KEYD
KEYAD
MICSENS
TELBEEP
1
IN/OUT2
4
13
5
4
IC551
TC4066BFT
BILATERAL SWITCH
1 3 23 5 6 8 9 10 14 4 13 17
A8V
VDD
TUN3V
ML
VOUTL
MC
MD
DATA
LRCK
SCK
BCK
13
15
7
DAC
IC531
PCM1753DBQ
14
1
2
3
16
OUT1IN+1
LPF
IC541
NJM4558MD
13
IN-1
2
IP-BUS DRIVER
CN601
32
BUSY
VDD
VDD
RESET
2
BUSY
31
CLOCK
CLOCK
DALMON
CNVSS
KYDT
7
CNVSS
DPDT
10
RESET
RST1
1
IC651
S-80835CNMC-B8U
1
2
3
5
9
8
4
10
DP
DM
D+
D-
4
3
30
23
24
5
3
4
5
6
1
2
3
35
37
38
10
29
39
BLUETOOTH
MODULE
:DEH-P610BT/XS/UC
:DEH-P6100BT/XS/UC
A
B
BUZZER
BZ601
X601
20.000MHz
JOYST
90
PICKUP UNIT
(P10.5)(SERVICE)
CD CORE UNIT(S10.5COMP2-iPod-C3)
C
BRST,BRXEN,BSRQ
CN701
Q101
M
LD
MD
S903
DSCSNS
SPINDLE
MOTOR
M
LOADING/CARRIAGE
MOTOR
LD-
MD
15
5
HOLOGRAM
UNIT
IC301
BA5839FP
IC201
PE5661A
RF AMP, CD DECODER, MP3&WMA DECODER
DIGITAL SERVO/DATA•PROCESSOR
CPU, USB HOST CONTROLLER
CD
DRIVER
2
VD
VD
VD
13
LOUT
9
CN101
16
SOP
15
SOM
18
LCOP
17
LCOM
21
CLCONT
55
LOUT
9
CONT
TD,FD
AC,BD,E,F
SD,MD
S901
HOME
S904
12EJ
S905
8EJ
LD+
14
141
LD
142
PD
12EJ
CONT
CLCONT
HOME
8
9
20
41
VDD
1
VDD2
BDATA,BSCK
Q201
17
/ADENA
VDD
15
5
FOCUS ACT.
TRACKING ACT.
FOP
TOP
2
1
TOP
FOP
11
FOP
14
TOP
2
1
14
8EJ
7
DSCSNS
10
VDD3
16
/RESET
8
/RESET
88
VREF
REFO
133
REFOUT
33
FOM
FOM
12
FOM
44
TOM
TOM
13
TOM
22
LOEJ
LOEJ
28
52
50
X201
XTAL
/XTAL
16.93MHz
VDSENS
11
16
17
DP
DM
4
5
DM
DP
2
1
X205
48MHz
USBXTAL
/USBXTAL
VDD2
Q102
39
/PUEN
VCC
VDD2
IC205
341S2162
iPod CP
CPRDY,CPRST
SDA,SCL
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
17
5678
56
7
8
C
D
F
A
B
E
BSENS
ASENS
B.UP
72
73
DALMON
67
10
Pre/SW_L
11
Rear_L
13
VP
SW
MUTE
5
3
21
23
OUT2(+)
OUT2(-)
OUT4(+)
OUT4(-)
ACC1
IN1_L
IN2
12
VCC1,VCC2
6,20
IN4
14
22 4
IC201
PML018A
AMP
IC351
PA2030A
Q921
SYSPW
ELECTRONIC VOLUME/
SOURCE SELECTOR
MUTE STBY
A8V
B.UP
BT3V
BT5V
1
85
AMPMUTE
49
SYSPW
64
BTPW
87
BTSENS
Q383
MUTE
Q301
12
Front-L
25
OUT
CONTROL
VOUT
H-SW/VOS_DET
BSENS
ASENS
SYS+B
IC911
NJM2388F84
5
10
12
11
9
1
4
CN981
JA301
VDD
SL
TUNPCE1
TUNPDO
TUNPDI
95
69
70
47
46
TUNPCK
48
CE1
DO
DI
CK
Q381
SWL
VBUS
AUXL
61
DDSYNC
VCK,VDT,VST
RCA OUT
SOURCE
CONNECTOR
RL22
BREM
RL21
FL22
FL21
IN
VIN
TUNPCE2
CE2
BO
B.UP
A12V
1
2
3
2
1
8
5
1
TUN3V
A8V
TUNER3V
IC431
NJM2885DL1-33
1
3
4
SL
BTMICMUTE
TELBEEP
BTRST5
BTTX5
BTRX5
DACCS
54
DACCK
56
DACDT
55
BTTX
33
BTRST
65
BTRX
34
BTMUTE3
45
TELBEEP2
24
BT3V
7
IN5-_L
1
IN5+_L
2
PVIN
VIN
EN/SYNC
4
Q302
2
Q303
6
B.UP
RCFL
RCRL
SWL
NT
T
Q304
B.UP
20
USBCTL
21
CN1101
Q382
CDL
IN4-_L
4
BUSL-
B.UP
CN801
14
7
AUXG
6
USBFLG
BT+B
B.UP
Q451
Q452
B.UP
1
6,7
IC261
NJM2360M
IC761
BD9007F
VOUT
5
1
3
4
VIN
EN
OC
IC741
BD6538G
HI-OUT12V
B.UP
A12V
Q262
Q261
DALMON
DPDT
KYDT
KYDT
D-
D+
KYDT
30
DPDT
DPDT
SW5V
29
SSENS
DSENS
71
18
38
ILMPW
SWVDD
ILM+B
SWVDD
VDD
Q842
Q841
15
ROT1
ILMCLR2
58
37
36
ROT0
ROT1
ROT0
17
16
ILMCLR2
10
SRC
4
DSENS
20
19
18
13
12
3
ILM+B
43
B.UP
Q822
Q821
SYSTEM
ONTROLLER
C601(1/2)
PEG544B8
IC461
NJM2885DL1-33
Q201
RL
FL
MICSENS
40
KEYAD
89
KEYD
2
K
S
T
SYSTEM
CONTROLLER
IC601(2/2)
PEG544B8
VDD
Q902
Q901
TUNL
6
IN2_L
BUSL+
AUXG
AUXL
3
IN4+_L
AUDIOL
5
IN3_L
B
GND
2
C
/UC
S/UC
B
A
MUTE
USB5V
JOYST
90
JOYST
8
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
18
1234
1234
C
D
F
A
B
E
FM/AM TUNER UNIT
A
A
A
A
FMRF
ANT adj
RF adj
FM ANT
T51
CF52
RFGND
OSCGND
DGND
AUDIOGND
NC
VCC
VDD_3.3
3.3V
2.5V
IC4
3.3V 2.5V
IC2
2.5V
NC
CE2
ROM_VDD
SL
DI
CK
CE1
DO
76 13 5 1098 11 14 1819 2021
1
3
212 1522 16 4 17
IC1
3.3V
AM ANT
FMRF
AT T
LPF
OSC
IC3 EEPROM
5.0V
IC5
5V 3.3V
AT T
MIXER, IF AMP
DET, FM MPX
23
Lch
NC
NC
NC
NC
NC
→
→
CN801
A
7
CN1101
JA1102
ROTARY COMMANDER
S1112
SRC
S1110
19
8
16
17
20
4
DSEN
SRC
6
USB
50
10
1
49
13
12
14
18
RXD
VCC
V3
REM
ROUT3
POUT1
TXD
LCD DRIVER/
KEY CONTROLLER
IC1101
PD6538A
AUXL
AUXR
AUXG
AUXL
AUXG
3
SW5V
ILMCTR2
ILM+B
CN1103
1
VBUS
3
2
1
3
D+
2
D-
D-
D+
VBUS
DPDT
JOYST
KYDT
KEYBOARD UNIT
B
10
15
ROT0
ROT1
Phase_B
Phase_A
57
47
46
X0
X1
54
X1101
55
KEY MATRIX
S1101
LIST
S1102
ipod
S1103
SW
S1111
PHONE
S1106
TA
BAND
S1105
S,Rtrv
S1104
CD EJECT
S1108
S1107
MUTE
S1109
DISP
KDT1-3,KST1-4
FRONT
AUX
48
59
D1104
Q1102
Q1101
LCD
D1103
D1141
Q1106
Q1103
ILLUMI
D1110
D1131
-
D1140
ILLUMI
IC1102
GP1UXC14RK
REMOTE CONTROL
SENSOR
3
1
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
19
5678
56
7
8
C
D
F
A
B
E
5. DIAGNOSIS
5.1 OPERATIONAL FLOWCHART
Vcc = 5 V
Pin 14
BSENS
Pin 73
ASENS
Pin 72
DSENS
Pin 58
ASENBO <- H
Pin 80
BSENS = L
DSENS = L
Starts
communication
with Grille
microcomputer.
SWVDD <- H
Pin 38
Source keys
operative
Source ON
SYSPW <- H
Pin 1
500 ms
500 ms
In case of the above signal, the communication
with Grille microcomputer may fail.
If the time interval is not 500 msec, the oscillator
may be defective.
Completes power-on operation.
(After that, proceed to each source operation)
Power ON
ASENS = L
Last source returns.
CD loading functions are available.
Keys except for EJECT key are not available.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
DEH-P610BT/XS/UC
20
1234
1234
C
D
F
A
B
E
5.2 ERROR CODE LIST
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.
(1) Basic Indication Method
1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.
2) Head unit display examples
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.
8-digit display 6-digit display 4-digit display
ERROR-xx ERR-xx E-xx
(2) Error Code List
Code Class Displayed error code Description of the code and potential cause(s)
10 Electricity Carriage Home NG CRG can't be moved to inner diameter.
SERVO LSI Com- CRG can't be moved from inner diameter.
munication Error -> Failure on home switch or CRG move mechanism.
Communication error between microcomputer and SERVO LSI.
11 Electricity Focus Servo NG Focusing not available.
-> Stains on rear side of disc or excessive vibrations on REWRITABLE.
12 Electricity Spindle Lock NG Spindle not locked. Sub-code is strange (not readable).
Subcode NG -> Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Turned over disc are found, though rarely.
CD signal error.
17 Electricity Setup NG AGC protection doesn't work. Focus can be easily lost.
-> Damages or stains on disc, or excessive vibrations on REWRITABLE.
30 Electricity Search Time Out Failed to reach target address.
-> CRG tracking error or damages on disc.
44 Electricity ALL Skip Skip setting for all track.
(CD-R/RW)
50
Mechanism
CD On Mech Error Mechanical error during CD ON.
-> Defective loading motor, mechanical lock and mechanical sensor.
A0 System Power Supply NG Power (VD) is ground faulted.
-> Failure on SW transistor or power supply (failure on connector).
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.
http://www.xiaoyu163.com
http://www.xiaoyu163.com
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74

Pioneer DEH-P6100BT - Radio / CD User manual

Pioneer
Brand
Pioneer
Model
DEH-P6100BT - Radio / CD
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents