5019 300 00017
CONSUMPTION DATA
Whirlpool is a registered trademark of Whirlpool USA.
Add detergent as indicated on the front page and as described in the
chapter “Detergent and Additives” in your Instructions for Use.
1. Turn the programme selector to the desired programme.
The display shows the programme duration in hours and
minutes as well as the predefined temperature. The “Start/
Pause” button blinks.
2. The temperature can be altered by pressing the
“Temperature” button.
3. The indication lamp of the predefined spin speed lights up; in
case you want to set another spin speed, press the “Spin/Rinse
hold” button.
ADD DETERGENTS, CLOSE THE LID AND
SELECT THE PROGRAMME
“LID OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to
show the the lid can be opened. As long as a wash programme is
running, the lid remains locked and must on no account be forced
open. In case you have an urgent need to open it during a running
programme, refer to “Cancel a running programme before the end”.
“Spin” button (incl. “Rinse hold”)
• Every programme has a predefined spin speed.
• Press the button to set another spin speed.
• If you select spin speed “0”, the final spinning is cancelled and
the water is drained out only. However, intermediate spin
phases remain during the rinse.
• If you select “Rinse hold”, the laundry remains in the last rinse
water without progressing to the final spin cycle, to avoid
creasing and prevent colours from changing. To activate the
“Rinse hold”, press the “Spin” button repeatedly until the
“Rinse hold” symbol on the display lights up.
- The wash programme stops to “Rinse hold” when the “Rinse
hold” symbol on the display blinks; the light of “Start/Pause”
button also blinks.
- To terminate the “Rinse hold” by spinning the laundry, press
“Start/Pause” - the laundry will be spun with the default spin
speed. You can also select another spin speed with the “Spin”
button before you start the spin cycle by pressing “Start/Pause”.
- To terminate the “Rinse hold” by draining the water without
spinning, press the “Spin” button until spin speed “0” appears
on the display; then press “Start/Pause” to start the
draining. Do not leave the laundry to soak for too long in the
“Rinse hodl” (especially silk).
“Colours 15° ” button
• Saves energy used for water heating while maintaining a good
wash result.
• Supports colour maintenance when washing coloured laundry.
• Recommendable for lightly soiled laundry without stains.
• Make sure that your detergent is suitable for cold wash
temperatures.
• Not selectable for Cotton 70 - 95°C.
“Rapid” button
• Enables quicker washing by shortening the programme duration.
• Recommendable for small loads or only lightly soiled laundry.
PROGRAMME START
ECO MONITOR
Open the tap and press the “Start/Pause” button. The
indication lamp next to the “Start/Pause” button lights up.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is
the case, an animation appears on the time display.
The “Eco monitor” gives you a rough feedback about the power
consumption of the programme setting you selected. As soon as
you turn the programme selector to any programme, the “Eco
monitor” is on.
less more
The indicator on the left is to show that the “Eco monitor” is active.
The four indicators next to it show the degree of consumption:
the less power your programme setting is forecasted to consume,
the less indicators will light up. This depends on the programme,
temperature and options selected, and also on the size of the wash
load. For that reason, the forecasted degree of power consumption
may adapt when the washing machine detects the wash load.
PROGRAMME END
• All the lights of the programme sequence indicator are off, and
the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the interior of the
machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
1. Press the “Start/Pause” button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the “Start/Pause” button again. The new programme
continues at the same position where the previous programme
was interrupted. Do not add detergent for this programme.
CANCEL A RUNNING PROGRAMME BEFORE
THE END
The “Reset/Drain” button cancels a programme before the end.
• Press the “Reset/Drain” button for at least 3 seconds. The
water is drained out; it may last a while until you can open the lid.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective
indication lights up. When the combination of programme and
additional option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are deselected
automatically.
“Prewash” button
• Only for heavily soiled loads (for example sand, granular dirt).
Increases the cycle time by approximately 15 min.
• Do not use liquid detergent for the main wash when activating
the Prewash option.
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with very soft
water, washing baby linen and helping people with allergies.
“Soil level” button
• Adapts the programme duration to the soil level of your
laundry. Also influences the detergent quantity.
= lightly soiled - = normaly soiled - = heavily soiled
Not all soil levels are selectable for each programme.
START DELAY
The “Start delay” button allows to run the machine at the
consumer's convenience, for example at night when electricity is
cheaper. Do not use liquid detergent when activating the “Start delay”.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay time 1 to 23 hours;
• Press the “Start/Pause” button. The indication light over the
“Start delay” button flashes and the countdown of the delay
time begins. The dot between hours and minutes of the delay
time indicated flashes.
• The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
• Once having pressed the “Start/Pause” button, the number
of hours preselected can be changed by pressing and holding
the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
• Turn the programme selector to another position or press the
“Reset/Drain” button.
..after having pressed the “Start/Pause” button:
• Press “Start/Pause” - the delay time disappears from the
display; press “Start/Pause” again to start the selected
programme immediately.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with
respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer
to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Standard Cotton programme and basis for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
FAILURE INDICATIONS
CHILD LOCK
DETERGENT OVERDOSAGE INDICATION
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Service” - Lighting up of the “Service” indication can be
caused by a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your “Instructions for Use”; if the
fault persists, contact our After Sales Service.
“Water tap closed” - The appliance has no or insufficient water
supply. Open the water tap: if the indications still lights up, refer
to the “Troubleshooting Guide” in the Instructions for Use.
“Clean filter” - Waste water is not pumped out. Check whether
the drain hose is kinked or the filter must be cleaned: in the latter
case refer to the Instructions for Use (“Removing the Filter”).
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “Off/0” position. To activate the child lock:
• Turn the programme selector to a programme position or run
a programme as usual.
• Press the 2 buttons marked with the key symbol simultaneously
for at least 3 seconds. The key-like symbol will shortly appear
on the display to ndicate that the child lock is active.
Any time you try to change a programme setting with active
child lock, the display will briefly show the key-like symbol.
The programme setting cannot be changed anymore. The only
change possible is to swithch the washer off by turning the
programme selector to the “Off/0” position.
To deactivate the child lock:
• Press again the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds.
the symbol will light up at the end of the programme if you
used too much detergent. use less detergent next time. If the
symbol lights up and the display shows “Fod”, too much foam
interrupted the wash process; refer to the “Troubleshooting
Guide” in your Instructions for use.
Programme
Tempe-
rature
(°C)
Load
(kg)
Water
(l)
Energy
without “Rapid”
(kWh)
Approx. Programme Duration (hrs : min)
without “Rapid” with “Rapid”
Mixed 40 3.0 45 0.43 1:00 –
Cotton 95 6.5 55* 1.90 2:35 2:00
Cotton 60 6.5 51 1.10 2:30 1:45
Cotton 40 6.5 51 0.60 2:20 1:30
Synthetics 60 3.0 54* 0.85 1:55 1:14
Synthetics 40 3.0 50 0.50 1:40 0:59
Delicates 40 1.5 50 0.55 0:45 –
Wool / Handwash 40 1.0 40 0.55 0:35 –
Baby 40 4.0 41 0.58 1:30 1:10
White 40 6.5 51 0.65 2:45 –
Light colours 40 4.0 67 0.50 1:20 1:00
Dark 40 4.0 41 0.58 1:40 1:10
Overnight 60 6.5 51 0.84 4:00 –
Aqua Eco 40 2.5 19 0.43 1:00 –
Speed 15´ 30 3.0 30 0.15 0:15 –
Eco Cotton** 60 6.5 51 0.85 3:30 –
Eco Cotton** 60 3.25 35 0.72 2:30 –
Eco Cotton 40 6.5 51 0.65 3:15 –
Eco Cotton** 40 3.25 35 0.49 2:30 –
Power consumption in off-mode 0.11 W / in left-on mode 1.93 W
If there is a programme setting which you use frequently, the
appliance offers the possibility to save one setting for each
programme so that it can be used again by just pushing one button.
• Select the desired programme, temperature, spin speed and
option(s), push and hold the “Favourites” button for at least
3 seconds. The lamp next to “Favourites” shortly flashes
and then lights up - the programme settings is saved.
Next time you want to use your individual programme settings,
select the programme, push the “Favourites” button and start
by pushing “Start/Pause”.
If you want to replace the saved programme setting by
another one:
• Select programme temperature, spin speed and options as
desired and then press and hold the “Favourites” button for
at least 3 seconds.The previously saved programme setting
will be replaced by the new one.
SAVE YOUR FAVOURITE PROGRAMMES