Zanussi DCS14S User manual

Category
Dishwashers
Type
User manual

This manual is also suitable for

INSTRUCTION BOOKLET
822 90 11-21
DISHWASHER
DCS 14 W
DCS 14 S
- 2 -
For the user
Important safety information 3
Description of the appliance 4-5
- Rinse aid dispenser
- Spray arm
- Coarse strainer
- Fine filter
- Detergent dispenser
- Water softener
- Water softener plug
The control panel and programmes 6
Using your appliance 7
How to load the dishwasher 8-9
-Instruction for verification tests
Maintenance and cleaning 10
- Important
- General cleaning
- Cleaning the filters
- Cleaning the cabinet
- Moving the machine
- Protecting the machine against freezing
If the machine is not working 11
Service 12
- Service and spare parts
- Customer care
Guarantee Conditions 13
Zanussi Service Force 14-15
For the installer
Technical specifications 16
Unpacking the machine 17
- If the machine is damaged
- Accossories
- Identification of materials
Installation 18-19
- Water inlet
- Water drainage
- Power supply
Guide to use the instruction book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Step by step instructions
Hints and tips
Environmental information
Contents
- 3 -
822 90 11-21
Before installing and first using the dishwasher, read the instruction booklet carefully, including
its hints and warnings. Doing so will ensure that your machine will perform properly and to best
advantage. Anyone using the machine should be thoroughly familiar with its instructions for use
and safety features. Save these instructions and make sure they remain with the machine if it is
moved or sold, so that everyone using it through its life can be properly informed on appliance
use and safety.
Installation
All installation work and other work done on the product
must be carried out by a qualified technician. Work
performed by persons with inadequate know ledge
may adversely affect the satisfactory functioning of
the product and may cause personal injury or damage.
This appliance is heavy. Care should be taken when
moving it.
Make sure that the power cord is not nipped or other-
wise damaged and that its hoses do not get crushed
or kinked when moving the dishwasher in connection
with installation or cleaning etc.
Child Safety
This appliance is designed to be operated by adults.
Children should not be allowed to tamper with the
controls or play with the product.
Keep all packaging well away for children.
Keep all detergents in safe place out of children´s
reach.
During Use
This dishwasher is designed solely for washing house-
hold utensils suitable for machine washing and only
in accordance with these instructions. Using it for
other purposes could lead to physical injury or damage
to property.
Items that are contaminated by petrol, paint.steel or
iron debris, corrosive, acidic or alkaline chemicals
must not be washed in this dishwasher.
Avoid opening the door while the machine is running.
If you take any dishes out of the machine before the
end of the dishwashing cycle, it is extremely important
to rinse them thoroughly under running water to remove
any remaining detergent.
Only use detergent specifically designed for use in
dishwashers.
Long bladed knives stored in an upright position are
a potential hazard.
Long and/or sharp items of cutlery such as carving
knives must be positioned horizontally in the basket.
When finishing loading or unloading close the door,
as an open door can be a hazard.
Make sure that the machine is disconnected from the
power supply during cleaning and maintenance work.
After using the machine, turn off its water supply and
disconnect it from the power supply. When removing
the electrical plug, grip the plug, not the lead.
Servicing and repairs must be carried out by a service
company authorised by the supplier. Use only spare
parts supplied by these. Never try to repair the machine
yourself.
Conservation
In the interest of the environment:
At the end of the machine's useful life, disconnect
the electrical plug from the power supply, then cut
the electrical lead at the point where it enters the
machine. Make quite sure that children will not be
able to play with the severed lead and plug.
Important safety information
- 4 -
Description of the appliance
1
2
3
4
5
6
1. Rinse aid dispenser
2. Spray arm
3. Coarse strainer
4. Fine filter
5. Detergent dispenser
6. Water softener
- 5 -
Rinse aid dispenser
Use of rinse aid will result in faster drying of the load and
gives the dishes a shiny finish. It may be necessary to adjust
the quantity of rinse aid dispensed if you live in either a very
hard water or a very soft water area. More is needed for
hard water and less for soft water. Leave the dispenser in
its preset position when you first use the dishwasher and
only adjust if, after a few cycles, you notice the following:
• Crockery remaining dull looking and/or showing
occasional round spots. If this happens, increase the
quantity of rinse aid by turning the red dial below the
filter trough clockwise.
• Crockery feeling sticky or showing whitish spots. If this
happens, decrease the quantity of rinse aid by turning
the red dial below the filler trough anti-clockwise.
The dispenser holds about 140 ml. This is enough for 40-
70 wash cycles, depending on the dosage setting. When
the rinse aid level is approaching the bottom of the scale it
is time to refill the dispenser. Swivel out the filler trough and
carefully fill up with rinse aid until the level reaches up to the
red mark on the level indicator tube. Do not overfill and
carefully wipe off any spillage to prevent sudsing problems.
Don’t forget to close the filler trough afterwards.
Do not fill the rinse aid dispenser with liquid
detergent.
Spray arm
It is important to keep all the holes in the spray arm clear.
If the spray arm becomes blocked this will affect washing
efficiency. If the spray arm needs cleaning, unscrew the
nut clockwise (left-hand thread) and lift off the spray arm.
Clear the holes and shake out any food particles.
Coarse strainer
The purpose of the coarse strainer is to catch large objects,
such as toothpicks and pieces of eggshell. Make sure that
the strainer is always clean. Lift it out and rinse it under
running water whenever necessary.
Fine filter
It is just as important to keep this filter clean. A dirty or
clogged filter will impair washing efficiency. The fine filter
can easily be lifted out for cleaning when you have removed
the coarse strainer.
Detergent dispenser
Only use detergents specially designed for dishwashers.
Open the detergent compartment on the inside of the door
by pushing the lid catch sideways. Pour the detergent into
the compartment, for a normal load pour about 15g.
Close the lid firmly. The detergent will be automatically
dispensed at the right time. Pre-wash detergent is not
generally needed, but if the dishes ar heavily soiled add
an extra 5g anywhere on the inside of the door.
Since not all detergents are the same, you should also
consult the instructions on the packet. Using the correct
amount of detergent also contributes to reducing pollution.
Zanussi recommends the use of Finish dish-
washer detergent and Rinse Aid.
Water softener
This dishwasher is equipped with a water softener for hard
(chalky) water, therefore the rinse aid dispenser should
be set for a low dosage.
The lime (chalk) in hard water causes white deposits to
occur on dishes and the interior of the dishwasher.
To prevent this, the water has to pass through a special
container where its hardness is removed. Since the water
softener consumes coarse dishwasher salt, you will have
to replenish the salt container after a certain number of
dishwashing cycles. When the indicator lamp on the
control panel lights up, it is time to fill up with salt.
Proceed as follows:
1. Unscrew the salt container filler cap.
2. Fill up salt container with water (only the first
time).
3. Fill the container with coarse salt. Use the funnel
supplied with the machine.
Ordinary domestic salt will affect the effiency of
the water softener and damage it.
4. Remove the funnel and wipe off any spillage.
5. Screw the filler cap back in place.
The salt container holds about 1 litre, which is enough for
about 20 - 30 dishwashing cycles. Always ensure that
there is water in the salt container before filling salt.
Only fill with salt just before starting one of the
complete washing programmes. This will prevent
any grains of salt or salty water, which may have
been spilled, remaining in the bottom of the
machine for any period of time, this could cause
corrosion.
Water softener plug
As supplied from the factory,
the water softener is set for
a water hardness of up to
20°dH. If your water is harder
than this, you can increase
the capacity of the water
softener by pulling out the
rubber plug at the rear of the
dishwasher on the left hand
side viewed from the back.
See illustration.
Contact your local Water Authority to find the exact water
hardness level for your area.
Never run the dishwasher without salt in the container as
this may damage the water softener. If the damage is slight,
the water-softener function can be partially restored by
filling the container with salt and then running the Normal
cycle 4-5 times.
The control panel and programmes
- 6 -
123 6 5 4
1 On/Off-button
Press the button in order to start the required
programme.
2 Temperature selector
55° - Button in
65° - Button out
3 Extra drying effect
If the button is pressed in the temperature of the
final rinse water will be higher and the drying effect
will be improved.
4 Programme selector
Turn the programme selector clockwise to the
programme required and press in the On/Off button.
To isolate the dishwasher from the mains completely,
unplug it from the wall socket.
5 Indicator lamp
While the programme is in progress, the operating
lamp is lit and it goes out when the programme is ready.
6 Salt indicator lamp
The operating lamp indicates when the salt needs to be
replenished. The lamp may remain lit for one or more
programmes after replenishment, which is fully normal.
Door lock
Press the handle down and open the door. Avoid opening
the door while the machine is running. If the door is opened
and is put standing ajar after a completed programme the
dishes will dry faster.
Programmes
Rinse & Hold is used if you want to wait until you have
a full load. This cycle rinses the load and keeps it moist,
making the main wash easier later on.
No detergent should be used. It does not matter which
temperature you select.
Intensive for loads which have heavily dried-on food
remnants and for those which are heavily soiled.
Normal for normal soiled loads. Replaces the pre wash
with one rinse without heating.
Economy is used for lightly soiled loads which do not
need any rinse off, such as cups, saucers and glasses.
Using your appliance
- 7 -
Proceed as follows:
1. Scrape off solid food remnants.
2. Load the dishwasher.
(See page 8: “How to load the dishwasher”).
Pour aprox 15 g detergent into the detergent
dispenser and cloce the dispenser lid.
If the dishes are heavily soiled add an extra
5 g anywhere on the inside of the door.
3. Close the door.
4. Select a suitable programme.
5. Select the required temperature and eventually
the option for extra drying. The programme gets
started when the On/Off button is pressed in.
6. Check the strainers to see whether they need
cleaning when the dishwasher has finished
the wash.
1
2
3
4
5
6
How to load the dishwasher
- 8 -
The illustration to next page shows the machine loaded
with five standard place settings. Your own dishes are
not likely to be identical to this load, but if you follow the
advice below we are sure you will be pleased with the
results.
• Always place glasses, cups and bowls upside down.
• Incline deep dishes (soup plates etc.) so that the
water can run off when drying.
• Make sure that the dishes do not rest against each
other. This is particularly important in regard to the
cutlery basket - nested spoons, etc. simply cannot be
properly washed. MAKE SURE THAT THE WATER
CAN GET AT ALL THE SOILED SURFACES.
• Make sure that cutlery with slender handles and other
items do not protrude through the openings in the
basket and prevent the spray arm from rotating.
• Never put silver and stainless steel objects together.
When these metals come into contact with each other
a chemical reaction occurs which stains the silver.
• China with a pattern applied on top of the glaze may
not be suitable for machine washing as the colours
may fade and lose their lustre. The same applies to
cutlery with wooden or plastic handles.
Always buy articles that are machine washable
in future.
• Not all plastic articles are machine washable. If you
are in doubt as to whether your plastic-ware can be
washed in the machine, we suggest you check by
washing a single item or else wash them by hand.
• Aluminium becomes dull and tarnished when machine
washed. The machine gets it clean, but at the expense
of its appearance.
• When washing delicate items, select the lower wash
temperature.
• Substances such as ketchup containing strong
colouring agents can cause temporary discoloration
in the machine.
Rack and basket
Cutlery basket
Dish rack
- 9 -
Detergent recommendations
For best results we recommend the use of Finish detergents, rinse aid and salt.
A complimentary sample pack is included in your new dishwasher.
1
Instruction for verification tests.
Test standard: EN 50242
Rated capacity: 5 place settings
Loading of rack: According to figure 1
Test program: Normal 65° C (+ Extra Drying)
Detergent (IEC type B): 15 gram in the dispenser
Rinse aid (typ III): Setting medium
Feed water pressure: Minimum 0,8 bar, maximum 10 bar
Waste water outlet: Install according to figure 2
The salt container and rinse aid dispenser shall be filled in accordance with the instruction manual. Before conducting
the measurements the dishwasher shall be operated for one or two complete cycles using detergent and a clean load.
2
Important
Make sure that the machine is unplugged and the water
turned off before undertaking any kind of maintenance.
General cleaning
Inspect the filters and spray arm nozzle before re-loading
the machine and remove any food scraps. Wipe round
the rubber gasket at the bottom of the door to remove
grease which tends to collect there.
Cleaning the filters
There are two filters, a coarse one and a fine one which
should be cleaned after every wash. Lift out these filters
which are in the base of the dishwasher and wash under
running water.
The dishwasher must not be used without the
filters. Incorrect repositioning of the filters will
produce poor washing results.
Cleaning of the filters is vital to ensure correct
operation of the machine.
Cleaning the spray arm nozzle
The holes in the spray arm nozzle must be kept free of
scraps for the efficiency of the washing action.
Inspect the spray arm regularly. When thorough cleaning
is necessary, remove the spray arm by unscrewing the
nut clockwise (it has a left-handed thread) and lift off the
spray arm.
Wash the spray arm with hot soapy water using a stiff
saucepan brush if necessary to remove scraps.
Re-assemble carefully, making sure the nut is secure.
Cleaning the cabinet
Wipe the outside of the cabinet and control panel regularly
with a soft damp cloth. When necessary, use liquid kitchen
or household cleaner to remove stubborn marks, rinse with
a damp cloth and rub up with a soft duster.
Never use abrasive cleaners which could damage the
surface, ie: scouring pads or solvents (acetone, trichlori-
ethylene, etc).
If the machine is not going to be used for some time, take
the folllowing precautions:
1. Unplug the machine and turn off the water supply.
2. Fill up the rinse aid container.
3. Make sure the tub is clean by carrying out a wash
programme (without any crockery) using Finish
Dishwasher cleaner, then dry the inside thoroughly.
4. Leave the door ajar.
Moving the machine
If you have to move the machine (you are moving
house, etc):
1. Unplug it.
2. Turn off the water tap.
3. Remove the water inlet and discharge hoses.
Avoid tilting the machine during transportation.
Protecting the machine against freezing
If the machine is kept in a place where the temperature
may sometimes fall below 0°C, there is a risk that the
small amount of water which remains inside parts of the
machine after normal use will freeze and damage it.
To prevent this you should:
1. Turn off the water supply to the machine and
disconnect the water intake hose from the
supply pipe.
2. Select a wash programme, start the machine
and let the programme run for a short time.
- 10 -
Maintenance and cleaning
- 11 -
If the machine is not working
The machine will not start.
The machine is not filling with water.
The machine will not drain.
The dishes are not clean (poor wash).
Visible lime deposits or white film on
the dishes.
The machine is noisy.
The dishes are not quite dry.
Have you pressed the ON/OFF button?
Has the machine no power supply?
Check circuit-breakers/fuses (start with fuse in electrical plug).
Is the door closed properly?
Have you set the programme control knob properly?
Is the machine's water tap turned on?
Is the machine's water tap turned on?
Has your domestic water supply been cut off temporarily?
Is the water intake hose kinked or blocked?
Is the filter inside the intake hose blocked?
Is the water pressure too low?
Is the drain hose kinked?
Is the sink drain blocked?
Is the drain hose extension not correct?
Is there no air vent in the end of the drain hose?
Are the baskets too full?
Have the dishes not been arranged properly?
Does the spray arm not rotate?
Are the spray arm holes clogged?
Are the filters clogged?
Are the filters not in position?
Not enough detergent has been used or is it unsuitable?
Is the detergent old or has gone hard?
Is the salt container cap not properly closed?
Is the washing programme selected too gentle?
Is the end of the drain hose submersed in waste water
(in the sink?)
Is there no salt or has the softener not been adjusted to the
hardness of the water?
Has the rinse aid run out or is too little being used?
Are the dishes rattling against each other?
Is the spray arm knocking against the dishes?
Have the dishes been left too long inside the machine?
Symptom Check
The door is difficult to close.
Is the dishwasher not level?
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below.
Never attempt to repair the dishwasher yourself.
Repairs carried out by unauthorised or inexperienced
persons can cause injury or serious malfunctioning.
- 12 -
Service and spare parts
If you require an engineer or you wish to purchase spare parts
contact your local Zanussi Service Force Centre by telephoning:
0870 5 929929
Your call be routed to the service centre covering your post code
area. Before calling an engineer please read the checklist under
the heading ‘If the machine is not working’, as you may be able
resolve the problem yourself.
In-guarantee customers should ensure that the checks have
been made as the engineer will make a charge if the fault
is not a mechanical or electrical breakdown.
Please note that proof of purchase is required for any in-guarantee
service calls.
When you contact the Service Centre you will need to give the
following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance
(found on the rating plate)
5. The purchase date
Customer Care
For general enquiries or for further information on Zanussi
products, please contact our Customer Care Department at:
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
Tel: 08705 727727 *
Site: www.zanussi.co.uk
* call to this number may be recorded for training purposes.
Service
- 13 -
Guarantee Conditions
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of the purchase this Zanussi appliance or any part thereof
is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the
same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorised by us
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre
Any appliance or defective part replaced shall become the Company’s property
This guarantee is in addition to your statutory and other legal rights
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours in
which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside the
United Kingdom
Appliances found to be in use within a commercial environment, plus those which are the subject to rental
agreements
Products of Zanussi manufacture which are not marketed by Zanussi
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home subject
to the following qualifications:
The guarantee starts from the date you first purchased your product
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products
This guarantee relates to you and cannot be transferred to another user
Your new home is within the European Community (EC) or European Free Trade Area
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household
The product is installed taking into account regulations in your new country
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new
home. They will then ensure that the local Service Organisation is aware of your move and able to look after you and
your appliances.
France Senlis +33 (0)3 44 62 29 99
Germany Nurnberg +49 (0)911 323 2600
Italy Pordenone +39 (0)1678 47053
Sweden Stockholm +46 (0)8 738 79 50
UK Slough +44 (0)1753 219897
- 14 -
Zanussi Service Force
To contact your local Zanussi Service Force Centre telephone 08705 929 929
CHANNEL ISLANDS
GUERNSEY Guernsey Electricity
PO Box 4
Vale, Guernsey
Channel Islands
JERSEY Jersey Electricity Company
PO Box 45
Queens Road
St Helier
Jersey
Channel Islands JE4 8NY
SCOTLAND
ABERDEEN 54 Claremont Street
(M05) Aberdeen AB10 6RA
AUCHTERMUCHY 33a Burnside
(M03) Auchtermuchy
Fife KY14 7AJ
BLANTYRE Unit 5
(M07) Block 2
Auchenraith Ind Estate
Rosendale Way
Blantyre G72 0NJ
DUMFRIES 93 Irish Street
(M01) Dumfries
Scotland DG1 2PQ
DUNOON Brair Hill
(M67) 7 Hill Street,
Dunoon
Argyll PA23 7AL
GLASGOW 20 Cunningham Road
(M04) Clyde Estate
Rutherglen
Glasgow G73 1PP
INVERNESS Unit 3B
(M06) Smithton Ind. Estate
Smithton
Inverness IV1 AJ
ISLE OF ARRAN Arran Domestics
Unit 4 The Douglas Centre
Brodick
(OWN SALES) Isle of Arran KA27 8AJ
ISLE OF BARRA J Zerfah
244 Bruernish
Isle of Barra
(OWN SALES) Western Islands HS9 5QY
ISLE OF BUTE Walker Engineering
Glenmhor
Upper Serpentine Road
Rothesay
Isle of Bute PA20 9EH
ISLE OF LEWIS ND Macleod
16 James Street
Stornoway
Isle of Lewis PA87 2QW
KELSO 2-8 Wood market
(M08) Kelso
Borders TD5 7AX
ORKNEY Corsie Domestics
(M65) 7 King Street
Kirkwall
Orkney KW15
PERTH Hydro Electrical
Inveralmond House
Ruthervenfield Road
Perth PH1 3AQ
PERTH Graham Begg
Unit 4
Airport Ind. Estate
(OWN SALES) Wick KW1 4QS
SHETLAND Tait Electronic Systems Ltd.
Holmsgarth Road
Lerwick
(OWN SALES) Shetland ZE1 0PW
SHETLAND Bolts Shetland Ltd.
26 North Road
Lerwick
(OWN SALES) Shetland ZE1 0PE
WHALSAY Leask Electrical
Harisdale
Symbister, Whalsay
(OWN SALES) Shetland ZE2 9AA
NORTHERN IRELAND
BELFAST Owenmore House
(M27) Kilwee Business Park
Upper Dunmury Lane
Belfast BT17 0HD
WALES
CARDIFF Guardian Industrial Estate
(M28) Clydesmuir Road
Tremorfa
Cardiff CF2 2QS
CLYWD Unit 6-7 Coed - Parc
(M14) Abergele Road
Rhuddlan
Clwyd
Wales LL18 5UG
DYFED Maes Y Coed
(M77) High Mead
Llanybydder
Carmarthenshire
SA40 9UL
HAVERFORDWEST Cromlech Lodge
(M75) Ambleston
Haverfordwest
Pembrokeshire
SA62 5DS
OSWESTRY Plas Ffynnon Warehouse
(M17) Middleton Road
Oswestry SY11 2PP
NORTH EAST
GATESHEAD Unit 356a
(M39) Dukesway Court
Dukesway
Team Valley
Gateshead NE11 0BH
GRIMSBY 15 Hainton Avenue
(M42) Grimsby
South Humberside
DN32 9AS
HULL Unit 1
(M41) Boulevard Ind. Estate
Hull
HU3 4AY
LEEDS 64-66 Cross Gates Road
(M37) Leeds
LS15 7NN
NEWTON AYCLIFFE Unit 16
(M45) Gurney Way
Aycliffe Ind. Estate
Newton Aycliffe
DL5 6UJ
SHEFFIELD Pennine House
(M38) Roman Ridge Ind.
Roman Ridge Road
Sheffield S9 1GB
NORTH WEST
BIRKENHEAD 1 Kelvin Park
(M11) Dock Road
Birkenhead
L41 1LT
CARLISLE Unit 7
(M10) James Street Workshops
James Street
Carlisle
Cumbria CA2 5AH
ISLE OF MAN South Quay Ind. Estate
(M64) Douglas
Isle of Man IM1 5AT
LIVERPOOL Unit 1
(M15) Honeys Green Precinct
Honeys Green Lane
Liverpool L12 9JH
MANCHESTER Unit B
(M09) Central Ind. Estate
St Marks Street
Bolton BL3 6NR
PRESTON Unit 250
(M13) Dawson Place
Walton Summit
Bamber Bridge
Preston
Lancashire PR5 8AL
STOCKPORT Unit 20 Haigh Park
(M16) Haigh Avenue
Stockport SK4 1QR
- 15 -
Zanussi Service Force
To contact your local Zanussi Service Force Centre telephone 08705 929 929
MIDLANDS
BIRMINGHAM 66 Birch Road East
(M18) Wyrley Road Ind. Estate
Witton
Birmingham B6 6DB
BOURNE Manning Road Ind. Estate
(M44) Pinfold Road
Bourne PE10 9HT
BRIDGNORTH 68 St. Mary’s Street
(M72) Bridgnorth
Shropshire WV16 4DR
GLOUCESTER 101 Rycroft Street
(M23) Gloucester GL1 4NB
HEREFORD Unit 3
(M31) Bank Buildings
Cattle Market
Hereford HE4 9HX
HIGHAM FERRERS 30 High Street
(M51) Higham Ferrers
Northants NN10 8BB
ILKESTON Unit 2
(M43) Furnace Road
Ilkeston DE7 5EP
LEICESTER Unit 7
(M22) Oaks Industrial Estate
Coventry Road
Narborough
Leicestershire LE0 5GF
LINCOLN Unit 8
(M40) Stonefield Park
Clifton Street
Lincoln LN5 8AA
NEWCASTLE 18-21 Croft Road
UNDER LYME Brampton Ind. Estate
(M12) Newcastle under Lyme
Staffordshire ST5 0TW
REDDITCH 13 Thornhill Road
(M20) North Moons Moat
Redditch
Worcestershire B98 9ND
TAMWORTH Unit 3
(M19) Sterling Park
Claymore
Tamworth B77 5DO
WORCESTER Unit 1 & 2
(M73) Northbrook Close
Gregorys Mill Ind. Estate
Worcester WR3 8BP
LONDON & EAST ANGLIA
BECKENHAM 11A Gardener Ind. Estate
(M79) Kent House Lane
Beckenham
Kent BR3 1QZ
CHELMSFORD Hanbury Road
(M47) Widford Ind. Estate
Chelmsford
Essex CM12 3AE
COLINDALE Unit 14
(M53) Capitol park
Capitol Way
Colindale
London NW9 0EQ
ELTHAM 194 Court Road
(M78) Mottingham
Eltham
London SE9 4EW
ENFIELD 284 Alma Road
(M49) Enfield
London EN3 7BB
GRAVESEND Unit B4
(M57) Imperial Business Estate
Gravesend
Kent DA11 0DL
HARPENDEN Unit 4
(M46) Riverside Estate
Coldharbour Lane
Harpenden AL5 4UN
LETCHWORTH 16-17 Woodside Ind. Estate
(M50) Works Road
Letchworth
Herts SG6 1LA
LONDON 2/4 Royal Lane
(M76) Yiewsley
West Drayton
Middlesex UB7 8DL
MAIDENHEAD Reform Road
(M60) Maidenhead
Berkshire SL6 8BY
MOLESEY 10 Island Farm Avenue
(M61) West Molesey
Surrey KT8 2UZ
NEWBURY 9 Pipers Court
(M24) Berkshire Drive
Thatcham
Berkshire RG19 4ER
IPSWICH Unit 6C
(M48) Elton Park Business Centre
Hadleigh Road
Ipswich IP2 0DD
NORWICH 2b Trafalgar Street
(M52) Norwich NR1 3HN
SUNBURY Unit 1a
(M63) The Summit
Hanworth Road
Hanworth Ind. Estate
Sunbury on Thames
TW16 5D
SOUTH EAST
ASHFORD Unit 2
(M58) Bridge Road Business Est.
Bridge Road
Ashford
Kent TN2 1BB
FLEET Unit 1
(M59) Redfields Ind. Estate
Church Crookham
Fleet
Hampshire GU13 0RD
HAYWARDS HEATH 21-25 Bridge Road
(M55) Haywards Heath
Sussex RH16 1UA
SOUTH WEST
BARNSTAPLE Main Road
(M30) Fremington
Barnstaple
North Devon EX31 2NT
BOURNEMOUTH 63-65 Curzon Road
(M26) Bournemouth
Dorset BH1 4PW
BRIDGEWATER 6 Hamp Ind. Estate
(M35) Bridgewater
Somerset TA6 3NT
BRISTOL 11 Eldon Way
(M25) Eldonwall Trading
Bristol
Avon BS4 3QQ
EMSWORTH 266 Main Road
(M33) Southbourne
Emsworth PO10 8JL
ISLE OF WIGHT Unit 8
(M34) Enterprise Court
Ryde Business Park
Ryde
Isle of Wight PO33 1DB
NEWTON ABBOT Unit 2
(M29) Zealley Ind. Estate
Kingsteignton
Newton Abbot
S. Devon TQ12 3TD
REDRUTH Unit 7D
(M36) Pool Ind. Estate
Wilson Way
Redruth
Cornwall TR15 3QW
Installation instructions
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Technical specifications
This appliance complies with E.E.C. directive Np. 87/308 of 2.6.87 relative to radio interference suppression.
DIMENSIONS Height 460 mm
Width 450 mm
Depth 480 mm
WEIGHT (net) 17 kg
(gross) 20 kg
CAPACITY 5 (standard IEC place settings)
WATER PRESSURES Minimum 50 kPa (0.5 bar)
Maximum 1000 kPa (10 bar)
ELECTRICAL DATA Power supply 230 V - 50 Hz
Fuse 13 A
Heating element 1200 W
Power rating 1280 W
- 16 -
Unpacking the machine
If the machine is damaged
If the machine has been damaged during transportation,
you should immediately notify the company responsible
for delivering it.
Check that the dishwasher is undamaged. If you discover
any damage, faults or that anything is missing, you should
notify the seller immediately.
Never leave packaging material in a place where children
may play with it.
Accossories
• Discharge hose (1)
• A funnel for filling with salt (2)
• Elbow for discharge hose (3)
• Hose clip (2x) for discharge hose
and the rubber nozzle (4)
• Washer/filter for inlet hose (5)
• A rubber nozzle for the discharge hose (6)
Identification of materials
All materials used in packaging this machine are
environmentally-friendly. The various plastics used
are identified and can be recycled:
• PE stands for polyethylene, which is used for the bag
around the machine and the bag in which these
instructions were supplied.
• PS stands for polystyrene (moulded), which is used for
the sections of packaging needed to cushion the machine.
The cardboard components of the packaging are made
from recyclable paper and should be taken to a collection
point for recycling.
The machine contains plastic and rubber components.
These have identifying marks to show what they are
made from, so they can be recycled or disposed of
properly at the end of the machine's life.
The materials are identified according to international
standards.
2
3
4
5
6
1
- 17 -
Installation
The dishwasher is intended for installation on a
kitchen sink or worktop. It is important to ensure
the dishwasher is level to avoid any difficulty
opening and closing the door. Its height can be
adjusted with the adjustable feet (8 mm each) in
each corner of the dishwasher.
Water inlet
The dishwasher should be permanently plumbed
into a separate cold water supply.
The water pressure must be within the limits given
in the technical specifications, as it will not function
correctly if pressure is outside these specifications.
Your local Water Authority will advise you on the
average mains pressure in your area. Where the
water is supplied from a cold water cistern you can
work out the pressure yourself by measuring the
vertical distance (or ‘Head’) between the machine’s
inlet hose and the outlet from the cold water storage
cistern; allowing .86 psi for every 2 feet under normal
conditions.
We would advise you to have a shut-off valve or
stopcock in the water supply pipe close to the dish-
washer and accessible for easy use. This should
be turned off when the appliance is not in use.
Insert the combination rubber washer/filter and
connect the inlet hose to a tap with a 3/4” pipe
thread.
The inlet hose (1) must not be joined onto any form
of extension hose. If it is too short, the entire hose
must be replaced with a longer high-pressure hose,
specially designed for the purpose.
The machine end of this hose can be turned in any
direction. Loosen the retaining nut, turn the hose,
then retighten the nut.
- 18 -
1
Water drainage
The grey discharge hose should be permanently
plumbed in. If this is not possible, it can be placed
in the sink to drain. Don’t forget that the water will
come out with some force, so position the pipe so
that the force of the water will not push the hose out
of the sink, use the elbow supplied which should be
fitted over the pipe to support it. Ensure the sink
outlet is not blocked.
Connect the discharge hose to the pipe stub at the
rear of the dishwasher, using the hose clip supplied.
It is important to push the discharge hose (2) onto
the pipe stub as far as it will go and tighten the hose
clip (3) as hard as possible. Make sure that the hose
clip is pushed as far towards the cabinet as possible
in order that it is covering both pipes completely.
The discharge hose must not at any point rise higher
than the top of the dishwasher. If it runs higher, ope-
ration of the dishwasher might be impaired. It is also
important to ensure that the inside diameter of the
hose is not less than 13 mm at any point.
If the discharge hose is too long it can easily be cut
to the right length.
1. Cut the hose to a suitable length, using a
sharp knife.
2. Fit the elbow supplied onto the end of the
hose.
Do not extend the hose under any circumstances as
this could affect the operation of the dishwasher.
Power supply
The dishwasher is supplied with a lead and electrical
plug for connection to a 230 V, 13 A earthed wall
socket. Before any work is carried out on the machine,
it must be isolated from the electric mains supply, for
example by removing the plug from the wall socket.
Permanent electrical installation must be
carried out by an authorised electrician.
- 19 -
2
3
© Electrolux Household Appliances Limited 2000
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Zanussi DCS14S User manual

Category
Dishwashers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI